English - La Nordica
Contents
1. 41 24 ALARM 41 25 WARRANTY CONDITIONS 42 1 WARNINGS Installation must carried out by qualified staff and or manufacturer technical assistance who must provide the buyer with a declaration of conformity for the system and will assume full responsibility for final installation and as a consequence the correct functioning of the installed product It is necessary to bear in mind all laws and national regional provincial and town council Standards present in the country the appliance has been installed The manufacturer cannot be held responsible for the failure to comply with such precautions 1 Electric connections it is therefore recommended that after any intervention on the product that authorised staff pay particular attention to the electric connections especially the stripped parts of the wires These must not escape from the terminal board in any situation thus preventing possible contact with the live parts of the wire 2 Type of use this stove must be destined for the use for which it has been expressly realised 3 Liability of the manufacturer The manufacturer is exempt from any liability contractual and extracontractual for injury damage caused to persons animals and objects due to installation adjustment and maintenance errors and improper use 4 Check integrity of the product After the packaging has b2. 4 Riscaldamento a Pellet USER MANUAL LUCREZIA LP14 LP20 LP30 Scheda 2202512 Rev002 200411 ENGLIS P Pe 63344 9 1 55 8585 9 2 COMMISSIONING OPERATIONS 10 2 1 BURN POT BRACKET LUCREZIA IDRO 10 3 MOUNTING THE TILES LUCREZIA IDRO 11 4 SAFETY 12 5 TECHNICAL FEATURES 13 6 SAFETY DEVICES eese eere eene eee eene eene annue 16 6 1 INSTALLATION AND SAFETY DEVICES 17 6 2 SAFETY DEVICES FOR CLOSED VESSEL SYSTEM 17 6 3 DISTANCES OF SAFETY DEVICES ACCORDING TO THE SIE DLL D rere 17 7 HYDRAULIC SYSTEM 1 17 8 AUTOMATIC THERMOSTATIC MIXER VALVE MANDATORY 18 9 INSTANT DOMESTIC WATER PRODUCTION ACCESSORY KIT 18 55 5 5 555505 6 19 10 1 INSTALLATIONS ALLOWED 19 10 2 INSTALLATIONS NOT ALLOWTLD 19 10 3 CONNECTION TO THE SMOKE EVACUATION n 19 10 3 1 5MOKE CHANNEL OR FITTINGS 19 10 3 2 CHIMNEY OR INDIVIDUAL FLUE
3. 20 10 3 3 DISTANCES RECOMMENDED FOR BOILER COMPARTMEN T aeui unu ute tentent been ado 20 10 3 4 APPLIANCE CONNECTION TO THE FLUE AND COMBUSTION PRODUCTS EVACUATION 21 10 3 S CHIMING GS AD u un 22 10 4 CONNECTION TO EXTERNAL AIR INLETS 22 10 5 INSULATION FINISHINGS COVERING AND SAFETY RECOMMENDATIONS uuu 23 10 6 NATIONAL REGIONAL PROVINCIAL AND TOWN 23 11 PELLETS AND FEEDING 23 12 PRODUCT FUNCTIONALITY 24 CONTROL BOARD tech crete eee eee 24 12 2 DISPLAY ICONS KE Y ism ER 24 13 FUNCTIONING CYCLE 25 13 1 BASIC INSTRUCTION 25 L 2 acetates 25 133201 25 13 4 PUMP FUNCTIONING 25 135 WCT OP u T 25 14 ADDITIONAL THERMOSTAT 25 14 1 ADDITIONAL THERMOSTAT FUNCTIONING WITH STBY sates acess E E 25 14 2 ADDITIONAL THERMOSTAT INSTALLATION 26 15 AIR DISCHARGE 26 16 USER 5 27 16 1 TEMPERATURE SE aderit Un EE D de RE 28 162 SET REGULATIONS 28 16 2 ENABLE CHRONO uuu ass
4. A OL 4 5 875 mm 5 19 12 4 23 2 S EH LP14 LP30 figure 10 figure 12 REFERENCES objects 5b mm 10 3 4 APPLIANCE CONNECTION TO THE FLUE AND COMBUSTION PRODUCTS EVACUATION The flue must receive the discharge from only one heat generator Direct discharge towards closed spaces is forbidden even with Clear sky The direct discharge of the combustion products must be at roof and the smoke pipe must have the features provided in the Chimney or individual flue section LP20 figure 11 Inspection 3 5 figure 13 17 HSI IDN3 gt Chimney cap fy windproof sx pipe B Inspection figure 14 External pipe that is isolated inspection figure 15 lt 3 m 54 Inspection 4 43 SE figure 16 10 3 5 CHIMNEY CAP The chimney cap must comply with the following requisites have an internal section equivalent to that of the chimney have useful outlet section not lower than double the chimney internal section be built in order to avoid rain snow foreign bodies penetrating the chimney and so that in the event of winds in any direction and inclination the discharge of the combustion products is assured be positioned in a way to guarantee an adequate dispersion 18 and dilution of the combustion products and however outside the reflux area in which the formation of counterpressures occu
5. Flow of water Water side resistance kg h Corresponding temperature difference 10K 1223 5 21 3 Flow of water Water side resistance cima un kg h Min working water pressure accepted ies Corresponding temperature difference AT 10K 1835 4 Flow of water Water side resistance Corresponding temperature difference 10 2751 6 TECHNICAL FEATURES LP14 20 Lucrezia 10 Safety valve discharge Thermometer Manometer e S Mw be lt figure 6 SI Flow 7 As balance valve Filling system ise ioe i Return exhaust Safety valve discharge Thermometer Manometer Ti 7 Flow 2 balance valve 3 Ma 2 Return 55 C automatic thermostatic mixing valve H Filling system gt lt si system exhaust 3 bar 1 2 safety drain boiler 1 flow outlet boiler 1 return inlet manometer thermometer filling system safety valve discharge TECHNICAL FEATURES graphics given below illustrate the behaviour of the pump used on our thermo products at the speeds that can be set x wes Head m NO LP30 Pump integrated in the thermo product with 5 m head Volume of expansion vessel integrated into thermo product 1 Automatic cleaning mechanism 5 0 Shell and tube turbulator clea
6. iJ Extraflame has an optional additional board that allows the boiler the following further functions when managing the system The table below indicates the various possibilities that the optional can offer rm nn a T Puffer pump or 4th heating area management Anti legionella management for DHW storage DHW storage chrono management Auxiliary output management and control LP30 DISPLAY AND PRODUCT FUNCTIONALITY 2 HSIIDN3 19 LP30 MENU STRUCTURE 3 TEMPERATURE SET H20 USER REGULATION LZ MANUAL AUTOMATIC e PELLET REGULATION is STOVE STATUS gt SET CLOCK TAS 5 LANGUAGE die gt SET HEAT 3l e SET USER SET CHRONO INSTALLER 28 LP30 MENU STRUCTURE 19 1 TEMPERATURE REGULATION SET 20 From the main screen turn P2 to select the icon Press P2 to confirm Turn P2 to regulate the temperature Confirm and memorising by pressing P2 To exit without memorising press key P1 From the main screen turn P2 to select the icon Press P2 to confirm Turn P2 to regulate the power Confirm and memorising by pressing P2 To exit without memorising press key P1 05 19 3 USER REGULATIONS MENU oF The set user menu offers the following possibilities
7. 35 HSI IDN3 22 TECHNICIAN YEARLY CLEANING Fumes motor disassembly and cleaning and fumes pipe new silicone in envisioned points Gaskets inspections ash drawer and door replace them and apply silicone where envisioned heat exchanger Feed box complete emptying and cleaning Check air intake pipe and cleaning of the flow sensor 36 TECHNICIAN YEARLY CLEANING 23 DISPLAYS Display START The start phase is in progress the continuous feeding of the pellets during the ignition a phase is in progress the normal working phase is in progress the boiler is working at the power set BURN POT CLEANING the automatic burn pot cleaning is in progress 5 FINAL CLEANING the final cleaning is in progress MODULATION the boiler is working at minimum power STAND BY 22 for re ignition due to an external the boiler will only re start when the external thermostats makes a request COOL STDBY BLACK OUT the boiler is cooling after a power cut once cooling is completed it will automatically ignite boiler in stand by for re ignition because the temperature of the water has exceeded the parameters set the anti freeze function is in progress as the H20 t is nee I _ ANTI FREEZE below the factory set threshold the pump is active until the water reaches the pre set factory parameter Ifthe boiler has remained in the Off status for at least 96 ANTILOCK hours the pump starts to function so that b
8. o wes figure 2 21 2 DEFLECTOR CLEANING It is necessary to remove the smoke deflector located under the cleaning springs of the heat exchanger every month To extract it follow the procedure below remove part A of the door upper deflector fixed with 3 screws remove part B of the door upper deflector fixed with 2 screws extract the smoke central deflector as if it were a drawer le zn a I NIS er LUCREZIA IDRO CLEANING 21 3 CLEANING THE ASH DRAWER The ash drawer must be emptied at least weekly and however on the basis of the frequency of use of the machine Before emptying the content into an appropriate container make sure that there are no hot ashes inside To open the drawer after having removed the ash drawer cover pull the handle as indicated by the arrows figure 32 figure 31 21 4 DOOR GASKET AND ASH DRAWER Thegasketsguaranteethetightnessofthe boilerandits consequent good functioning These must be checked regularly if they should be worn or damaged they must be replaced immediately These operations must be carried out by an authorised technician N B For correct functioning the boiler must undergo routine maintenance by an authorised technician at least once a year If the power supply cable is damaged it must be replaced by the after sales service or by a similarly qualified person so as to avoid al risks
9. pou b the switch off time of the 1st time period 1 22222 P5 displays START CLEANER Toconfirm and continue programming press the 5 button 2 regulate the times using the or key Press the P4 button to go back to the previous parameter gt press key displays STOP CLEANER regulate the times using the P2 Jor key memorise and exit pressing the P1 key several times USER PARAMETERS 25 17 QUICK ACCESS DIAGRAM for 3 seconds SET TEMPERATURE SET H20 PH ENABLE NE PERS onor REGULATIONS P4 Da lPL STOVE ADJUSTMENT P2 P3 PELLETS eran display of the various components B ETIN UNA 1 IPS START 5 i STOP CLEANING 4 CLEANER 1 CLEANER TECHNICAL MENU CHRONO MAX 4 TIME SPANS 26 QUICK ACCESS DIAGRAM 18 LP30 DISPLAY AND PRODUCT FUNCTIONALITY SABATO 29 04 2010 18 56 Boiler ignition or switch off key Encoder wheel by turning select the different icons on the display by pressing enter selection Multiple function key advancement through menus etc The flame icon is not present in the OFF START BURN POT CLEANING FINAL CLEANING ALARM RE START STBY status Flashes in IGNITION mode Fixed in START UP and WORK mode During the WORK phase it displays the flame with real work power
10. SELPRO COExtraflame START PRG1 STOP PRG1 MONDAY PRG1 LP30 MENU STRUCTURE 19 7 3 SET LANGUAGE MENU The boiler allows to set the con languages Italian English French German and Spanish ITALIAN is the default setting e Turn P2 to select the icon Press P2 to confirm Turn P2 to select LANGUAGE Confirm pressing P2 Turn P2 to select the desired parameter Press P2 to enter modification mode Turn P2 to modify the value Press P2 to confirm and exit If you wish to exit without memorising press key P1 COExtraflame USER MENU SET CLOCK SET CHRONO LANGUAGE SET HEAT EXCHANGER E 4 LANGUAGE A 2 O 19 7 4 SET HEAT EXCHANGER MENU 1 This menu allows to program the start and end time of automatic cleaning of the heat exchanger Cleaning takes place mechanically via metal springs that clean the exchange pipes By default the parameters are START 6 00 STOP 22 00 which mean that cleaning is excluded from 22 to 6 in the morning Turn P2 to select the icon Press P2 to confirm Turn P2 to select SET HEAT EXCHANGER Confirm pressing P2 Turn P2 to select the desired parameter Press P2 to enter modification mode Turn P2 to modify the value Press P2 to confirm and exit If you wish to exit without memorising pres
11. 22 AIR DISCHARGE FUNCTION 16 USER PARAMETERS D DISPLAY D2 TEMPERATURE 5 20 65 C 80 C Boiler water T regulation SET S ENABLE CHRONO x ON OFF Chrono activation deactivation ET REGULATIONS PELLET 30 420 Selecting the percentage of pellet feed REGULATION STATUS STOVESTATUS ST1 ST10 VALUE SETCLOCK MON SUN Setingthedayoftheweek _ HouRS Adjustmentofthehour MINUTES 200 459 Adjustment oftheminutes DATE 431 Adjustmentofthedate MONTH 112 Adjustmentofthemonth SET CHRONO OFF 00 00 SUNDAY OFF Setting room temperature for the 1 time span SUNDAY PRG2 OFF START PRG3 OFF 00 00 Time 3 ignition OFF 00 00 SUNDAY PRG3 OFF OFF 00 00 SUNDAY PRG3 OFF ITAL ENGL DEUT FRAN Se HEAT STARTCLEANER OF F 23 50__ Start heat exchanger cleaning time period CLEANING TECHNICIAN The following menu is reserved for the technical after sales service MENU The following menu is available only for products with version 1 firmware and not the successive versions USER PARAMETERS 23 HSI IDN3 16 1 TEMPERATURE SET This set allows to regulate the temperature of the water in the boiler with a range from 65 C to 80 C NN Vy AWE Procedure 4 16 2 SET REGULATIONS The menu allows to activate or deactivate the Chrono and regulate the flow of pellets 16 2 1 ENABLE CHRONO Vy AWE Procedure 7 Once the desired chrono time periods a
12. Do not touch the surfaces as they could still be unstable Air the room well several times The hardening of the surfaces is terminated after several heating processes This appliance must not be used to burn waste 13 2 IGNITION Before igniting the stove the following points must be verified thefeed box must be full of pellets combustion chamber must be clean The burn pot must be completely free and clean check the hermetic closure of the fire door and the ash 4 4 4 4 drawer make sure the power supply cable is connected correctly The bipolar switch in the rear right part must be positioned on 1 Press key 1 for 3 seconds If the machine has not ignited the NO IGNITION alarm occurs Inthe event of the alarm due to no ignition wait for the machine to cool down Press key 1LP1 for 3 seconds FUNCTIONING CYCLE 13 3 WORK The boiler will work to reach the water temperature set by the user see user menu The pump will start to function as soon as the factory set parameters are reached An always open heating area is recommended to make the product functioning homogenous avoiding overheating blocks boiler will automatically modulate when approaching the temperature set going to minimum power and then switching off H OFF if it will exceed the set over the factory set parameters When the temperature of the water drops within the factory set parameters the
13. MANDATORY The automatic thermostatic mixing valve finds applications in solid fuel boilers as it prevents cold water return into the exchanger Routes 1 and 3 are always open and together with the pump installed on the return they guarantee water circulation inside the biomass boiler exchanger An elevated return temperature allows efficiency improvement reduces formation of combustion product condensation and prolongs the boiler life span Valves on the market have different calibrations The company advises use of 55 C model with 1 hydraulic connections Once the valve calibration temperature is reached route 2 is opened and the boiler water goes to the system via the flow It is recommended not to use this device whenever the DHW is produced through an instant heat exchanger 9 INSTANT DOMESTIC HOT WATER PRODUCTION ACCESSORY KIT Warnings if the instant hot water production accessory kit is to be used contact the company technical after sales service AUTOMATIC THERMOSTATIC MIXER VALVE MANDATORY 10 INSTALLATION The installation must be in compliance with UNI 10683 2005 heat generators fed with wood and other solid fuels installation The chimneys must be in compliance with UNI 9731 1990 chimneys classification based on thermal resistance EN 13384 1 2006 Thermal and fluid dynamic calculation methods UNI 7129 point 4 3 3 Fire Department dispositions local rules and prescriptions UNI 1443 20
14. PRG2 00 10 OFF 00 00 STOP PRG2 00 10 0000 MONDAY PRG2 OFF SUNDAY PRG2 OFF ON OFF this is not the case press the key again lt Press the P5 key to select the day and the P2 and P3 key to activate ON or not activate OFF TEMPERATURE REGULATION FORTHE TIME PERIOD HSI IDN3 After having programmed the desired days press the P5 key to program the temperature of the water desired in that time period SET PRG1 will appear in the display Set the desired water temperature for the time period of interest using the P2 or P3 buttons Press the key to memorise and continue programming other time periods or exit pressing the P1 key For the other time periods follow the procedure described for the first and use the quick access diagram that follows for help SET PRG2 65 C 80 C START PRG3 00 10 OFF 00 00 STOP PRG3 00 10 OFF 00 00 MONDAY PRG3 OFF SUNDAY PRG3 OFF ON OFF SET PRG3 65 C 80 C START PRG4 00 10 OFF 00 00 STOP 4 00 10 OFF 00 00 MONDAY PRG4 OFF SUNDAY PRG4 OFF ON OFF SET PRG4 65 C 80 C The menu allows to set the language Let s suppose that the weekly programmer function is to be used 72 16 4 3 LANGUAGE and 3 time periods are to be used in the following way 2 Procedure 1st time span from 08 00 to 12 00 every day of the week excluding Saturday and Sunday 16 4 3 1 2nd time span from 15 00 to 22 00 only Saturday and Sunday 4 Press ke
15. automatic manual mode allows enabling disabling of the chrono inside the boiler pellet regulation allows pellet regulation 19 4 AUTOMATIC MANUAL MODE The automatic mode allows to ignite the boiler and switch it off following the programming set by the user To regulate the time periods see the CHRONO REGULATION paragraph From the main screen turn P2 to select the icon Press P2 to confirm Turn P2 to take chrono enabling to ON Confirm and memorising by pressing P2 to exit without memorising press key P1 LP30 MENU STRUCTURE 29 HSI IDN3 ENABLE CHRONO OFF 5 4 19 5 PELLET SETTING The boiler allows regulation of the pellets via the relative menu Considering the different types of pellets on the market the user can increase or decrease the amount of pellets as a percentage QIExtraflame 30 From the main screen turn P2 to select the icon Press P2 to confirm and successively press P2 again to select PELLET REGULATION Turn P2 to modify the parameter as a percentage Confirm and memorising by pressing P2 to exit without memorising press key P1 LP30 MENU STRUCTURE 19 6 STATUS MENU The status menu is used to display the status of the inputs and outputs in the board From the main screen turn P2 to select the Press P2 to confirm display of STATUS 1 screen Press P2 again to display STATUS 2 sc
16. boiler will re start Nota bene the general times of the various functioning status are variable on the basis of the type of system and on the basis of the parameters set 13 4 PUMP FUNCTIONING The pump activates water circulation when the temperature of the water inside the stove reaches approx 60 C As the pump always functions above 60 an always open heating area is recommended to make product functioning homogenous avoiding overheating blocks Normally this area is defined Safety zone 13 5 SWITCH OFF Switch off can take place manually by pressing key P1 three seconds automatically due to a control programmed from the utility in CHRONO mode due to a contact of an additional external thermostat satisfied or H OFF temperature of the water reached and exceeded When the operation has been performed the appliance automatically enters the switch off phase blocking the supply of pellets Display DT will show OFF The flue gas exhaust motor will remain on until the stove temperature has dropped below the factory parameters 14 ADDITIONAL THERMOSTAT N B Installation must be performed by an authorised technician It is possible to thermostat a room adjacent to the room where the stove is positioned just connect a thermostat following the procedure described in the next point it is recommended to position the optional mechanical thermostat at a height of 1 50m from the ground STBY fu
17. features The chemical physical features of the system and reinstate water are fundamental for the correct functioning and life span of the boiler Amongst the inconveniences caused by bad quality feeding water the most frequent is the scaling of the heat exchange surfaces Less frequent but equally serious is the corrosion of the water side surfaces of the entire circuit Itis known thatthe lime scale even if there is only a few millimetres due to their low thermal conductivity greatly reduce the heat exchange determining damaging localised heating It is strongly recommended to treat the water in the following cases a very hard water available higher than 20 b very extended systems c large water quantities restored due to leaks d subsequent fillings due to system maintenance work It is recommended to always contact specialised companies to treat the feeding water of the heating systems Filling the system Once the hydraulic connections have been carried out proceed to connecting the plant Open all air venting valves of radiators boiler and plant Gradually open the load cock ensuring that the air venting valves work regularly Using the manometer check that the system is pressurised In case of closed vessel system reach the pressure of about 0 11 0 12 MPa 1 1 1 2 bar Close the load cock and again release the air from the boiler through the venting valve 14 8 AUTOMATIC THERMOSTATIC MIXER VALVE
18. individual flue must respond to the following requisites seal the combustion products be waterproof and adequately insulated in line with the use conditions berealised with materials which resist the normal mechanical stress heat action of the combustion products and any condensate have mainly vertical progress with deviations from the axis not greater than 452 be adequately distanced from fuel or flammable materials through air space or opportune insulation have preferably circular internal section the square or rectangular sections must have round corners with a radius not lower than 20 mm have constant internal section free and independent have rectangular section with max ratio between the sides of 1 5 It is recommended that the smoke pipe be equipped with a collection chamber for solid materials and any condensate situated under the smoke channel inlet so that it can be easily opened and inspected from airtight door 10 3 3 DISTANCES RECOMMENDED FOR BOILER COMPARTMENT Below find images relative to the measurements that the company recommends are respected For the Lucrezia idro model respect the measurements for Lp14 INSTALLATION PO P Su ae S Py 252212 2 4 HI Qu Ri ll o 82 22 e ET gia Nora as N x d d IR e Se E bog Vv yc Ax 44 7 INSTALLATION 3 s
19. is functioning and hot to the touch especially all external surfaces attention must be paid Check for the presence of any obstructions before switching the appliance on following a prolonged standstill period The stove has been designed to function in any climatic condition also critical In particularly adverse conditions strong wind freezing safety systems may intervene that switch the stove off If this occurs contact the technical after sales service and always disable the safety system If the flue should catch fire be equipped with suitable systems for suffocating the flames or request help from the fire service This appliance must not be used to burn waste Do not use any inflammable liquids for ignition During the filling phase do not allow the bag of pellets to come into contact with the product 8 SAFETY 5 TECHNICAL FEATURES nota bene for the features of the Lucrezia Idro model consult the sheet attached to the inside of the product Features t PI4 20 LP30 333 1406 HSI IDN3 875 663 941 772 120 Airintakepipediameter 46 60 33 8 31 1 Tanvoume 7 61 0 12 470 230 50 1 2 2 5 2 5 br 06 l N N NO r Bolerdass 23 J 3 3 48 18 Yield 9 90 92 920
20. of the chrono i e automatic mode the boiler can ignite and switch off in automatic mode The chrono has absolute priority over every control therefore this factor must be considered Four time periods can be programmed By default all of the time periods are in OFF EXPLANATION First time period ignition time First time period switch off time day allowed or not on off day allowed or not on off day allowed or not on off day allowed or not on off day allowed or not on off day allowed or not on off day allowed or not on off setting water t Turn P2 to select the icon Press P2 to confirm Turn P2 to select SET CHRONO Confirm pressing P2 Turn P2 to select the desired parameter Press P2 to enter modification mode Turn P2 to modify the value Press P2 to confirm and exit If you wish to exit without memorising press key P1 OExtraflame SET CLOCK SET CHRONO LANGUAGE HEAT EXCHANGER aa of O A 2 32 5 SIAR 00 00 OP acetate acct 00 00 MONDAY PRG1 ON TUESDAY PRO assi tease OFF WEDNESDAY PRG1 OFF THURSDAY PRG 1 OFF FRIDAY PRG I caudis OFF SATURDAY 1 SUNDAY
21. similarly qualified person so as to avoid al risks LP14 20 figure 23 34 LP14 20 figure 24 With machine off open the ash drawer to empty the content The frequency of emptying the ash drawer will be proportional to the use of the product Lp30 has 3 drawers 30 30 X figure 26 20 3 CONNECTION TO THE FLUE AND CLEANING OF THE SAME Suckand clean the pipe that leads to the flue yearly or anytime that it is necessary If there are horizontal tracts the residues must be removed before they obstruct smoke passage NON CLEANING jeopardises safety Maintenance operations guarantee correct functioning of the product through time Failure to comply with these operations can jeopardise the safety of the product LP14 20 30 BOILER CLEANING 21 LUCREZIA IDRO CLEANING Some images could be offset from the original model Maintenance operations guarantee correct functioning of the product through time Failure to comply with these operations can jeopardise the safety of the product The cleaning operations must be performed when the stove is completely cold 21 1 BURN POT CLEANING The burn pot is cleaned via a mechanical system at pre fixed intervals automatically by the boiler The figure below shows the burn pot with underlying opening The company recommends to remove any ash residue using a suction device at least once every two days rA un 3 3 5
22. the machine from 250V overcurrents F rapid 85 C calibrated mechanical bulb with manual rearm intervenes by blocking fuel feed whenever the pellet tank t reaches the limit of 85 C Rearm must be performed by qualified staff and or the manufacturer s technical after sales assistance 100 C calibrated mechanical bulb with manual rearm intervenes by blocking the fuel feed whenever the t of the water inside the product is near to 100 Rearm must be performed after the boiler has cooled completely Minimum and maximum pressure switch intervenes in the event of inadequate water pressure Rearm must be performed by qualified staff and or the manufacturer s technical after sales assistance TABLE OF SAFETY DEVICES FOR CLOSED VESSEL SYSTEM AND NOT PRESENT IN THE PRODUCT Safety valve Pump control thermostat Temperature indicator Acoustic alarm activation thermostat Adjustment automatic circuit breaker switch firmware board Water overheating automatic circuit breaker switch block thermostat Circulation system Expansion system Safety dissipation system incorporated with the generator with thermal safety valve self activated whenever the appliance does not have a temperature self adjustment system Not necessary as the machine has a t self adjusting system and a block automatic circuit breaker switch During installation of the stove it is MANDATORY to adjust the system with a manometer in order t
23. 05 chimneys general requisites UNI 1457 2004 chimneys clay ceramic flue liners UNI 11278 chimneys smoke channels pipes flues metal pipes Selection and correct use depending on the type of application and relative designation of the product GLOSSARY CLOSED HEARTH APPLIANCE Heat generator which opening is only allowed through the loading of the fuel during use BIOMASS Biological material excluding the material incorporated in geological formations and transformed into fossils BIOFUEL Fuel produced directly or indirectly by biomass CHIMNEY Vertical pipe with the aim of collecting and expelling the fuel products coming from only one appliance at a convenient height from the ground SMOKE CHANNEL OR FITTING Pipe or connecting element between heat generator appliance and chimney to evacuate combustion products INSULATION Group of set ups and materials used to prevent the transmission of heat through a wall that separates rooms with different temperatures CHIMNEY CAP Device positioned at chimney peak to ease the dispersion of combustion products into the atmosphere CONDENSATE Liquid products that form when the combustion gas temperature is lower or equal to the water dew point HEAT GENERATORS Appliance which allows to produce thermal energy heat through the rapid transformation via combustion of the chemical energy of the same fuel GATE VALVE Mechanism for modifying the combustion gas dynamic
24. The side tiles are all the same 7 Position the ceramic covering between the two cast iron sides E p m a ae ge k e sa m MOUNTING THE TILES LUCREZIA IDRO 7 HSIIDN3 4 SAFETY For safety reasons remember that The stove must not be used by persons including children with reduced physical sensorial and mental capacities or who are unskilled persons unless they are supervised and trained regarding use of the appliance by a person responsible for their safety Children must be controlled to ensure that they do not play with the appliance Do not touch the stove when you are barefoot or when parts of the body are wet or humid The safety and adjustment devices must not be modified without the authorisation or indications of the manufacturer Do not pull disconnect twist electric cables leaving the stove even if disconnected from the electric power supply mains It is advised to position the power supply cable in a way that it does not come into contact with hot parts of the appliance The power supply plug must be accessible after installation Do not close or reduce the dimensions of the airing vents in the place of installation The airing vents are indispensable for correct combustion Do not leave the packaging elements within reach of children or unassisted disabled persons The hearth door must always be closed during normal functioning of the product When the appliance
25. aka eio 28 16 2 2 2 2 PELLET SET TING odit en esiti 28 28 16 4 USER MENU 28 16 4 1 SET CLOCK ettet 28 16 4 2 5 CHRONO tet 28 16 4 3 LANGUAQGE eet 29 16 4 4 EXCHANGER 29 17 QUICK ACCESS 30 18 1 DISPLAY AND PRODUCT FUNCTIONALITY 31 19 LP30 MENU STRUCTURIE 32 19 1 TEMPERATURE REGULATION 24 33 192 POWER REGULATION tee 33 19 3 USER REGULATIONS MENU 33 194 AUTOMATIC MANUAL MODE 9 G 33 19 5 PELLET SETTING g 34 19 6 STATUS MENU 222 35 197 SET USER M Let 35 19 7 1 SET 0012 2252 35 19 7 2 CHRONO REGULATION 36 19 7 3 SET LANGUAGE MENU O 37 19 7 5 HEAT EXCHANGER MENU lll 37 20 LP14 20 BOILER 38 20 1 BURN POT CLEANING e 38 20 2 DOOR GASKET AND ASH DRAWER e 38 20 3 CONNECTION TO THE FLUE AND CLEANING OF THE ttt ttt 38 21 LUCREZIA IDRO CLEANING 39 21 1 BURN POT CLEANING ee 39 21 2 DEFLECTOR CLEANING ee 39 21 3 CLEANING THE ASH DRAWER e 39 21 4 DOOR GASKET AND ASH DRAWER e 39 22 TECHNICIAN YEARLY CLEANING 40 23 DISPLAYS
26. een removed check the integrity and completeness of the contents If this does not comply contact the dealer where the appliance was purchased 5 Electric connections All electric components that make up the stove must be replaced with original spare parts exclusively by an authorised after sales centre thus guaranteeing correct functioning 6 Maintenance The stove must be serviced at least once a year programming it in advance with qualified staff and or the manufacturer s technical after sales assistance Nota bene In case of thermo product or boiler the product or system venting is not covered by the warranty WARNINGS 5 HSI IDN3 2 COMMISSIONING OPERATIONS 2 1 BURN POT BRACKET LUCREZIA IDRO MODEL ONLY ATTENTION Before igniting the stove make sure the bracket indicated in the figure has been removed by removing the screw that fixes it IN THE MODELS WHERE ENVISIONED figure 1 6 COMMISSIONING OPERATIONS 3 MOUNTING THE TILES LUCREZIA IDRO 1 Remove the 4 fixing screws of the 2 cast iron sides as indicated 3 Position the central tile in the appropriate iron hooks in the drawing 4 Fix the upper grate with the 2 previously removed screws 2 Remove the 2 screws that fix the upper grate 5 Position the side tiles the appropriate iron hooks starting 6 Reposition the 2 cast iron sides and fix with the 4 previously from the bottom upwards in the two sides of the stove removed screws NB
27. ened glass coverings and cast iron or Ironker grids the painted chrome or gold plated details the majolica the handles and the electric cables Colour variations crackles and slight size differences of the majolica parts are not a reason for claims as they are natural features of the materials themselves Parts refractory material Masonry work The system particulars for the production of domestic hot water not supplied by EXTRAFLAME S p A water products only The heat exchanger is excluded from the warranty unless an adequate anti condensate circuit is realised which guarantees a minimum return temperature of the appliance of at least 55 C only water products Further clauses The warranty also excludes any calibration or regulation interventions of the product in relation to the type of fuel or the type of installation The warranty is not extended if particulars are replaced No compensation will be paid for the time the product is inefficient This warranty is valid only for the purchaser and cannot be transferred WARRANTY INTERVENTIONS The request for information must be sent to the dealer The warranty intervention envisions the repair of the appliance without any charge as provided by the law in force LIABILITY EXTRAFLAME S p A does not grant any compensation for direct or indirect damage caused or depending on the product LAW COURT The Vicenza Law Court is elected as the competen
28. enerally the closed vessel system has one of the following expansion vessels Pre loaded closed expansion vessel with membrane impermeable to the passage of gases Automatic closed expansion system with compressor and membrane impermeable to the passage of gases Automatic closed expansion system with transfer pump and membrane impermeable to the passage of gases Expansion system without diaphragm GENERALITY The closed systems must have Safety valve Pump control thermostat Acoustic alarm activation thermostat Temperature indicator Pressure indicator Acoustic alarm Adjustment automatic circuit breaker switch Automatic circuit breaker switch block thermostat Circulation system Expansion system Safety dissipation system incorporated with the generator with thermal safety valve self activated whenever the appliance does not have a temperature self adjustment system The temperature safety sensors must be in place on the machine at a distance no greater than 30 cm from the flow connection Whenever the generators lack a device those missing can be installed on the generator flow pipe within a distance no greater than 1m from the machine Domestic type heating appliances with automatic feed must have a fuel block thermostat or a cooling circuit prepared by the manufacturer of the appliance activated by a circuit breaker safety valve such as to guarantee that the limit temperature set by the Standard is
29. er sales Service in the event of intervention The warranty is not considered valid in the following cases 31 The warranty conditions described above have not been respected 32 Installation has not been performed with respect to the Standards in force regarding the provisions described in the manual book provided with the appliance 33 Negligence of the customer due to lack of or incorrect maintenance of the product 34 Presence of electric and or hydraulic plants that do not comply with the standards in force 35 Damages deriving from atmospheric chemical electro chemical agents improper use of the product modifications and tampering with the product 38 inefficacy and or unsuitability of the flue and or other causes not deriving from the manufacture of the product 36 Combustion of materials not compliant with the types and quantities indicated in the manual book supplied 37 All damages caused by transport It is therefore recommended to carefully check the goods on receipt immediately informing the dealer of any damage making a note on the transport document and on the carrier s copy EXTRAFLAME S p A is not liable for any damage that can directly or indirectly affect persons objects and pets as a consequence of failure to comply with the prescriptions indicated in this manual book All particulars subject to normal wear are not covered by warranty This category includes gaskets all ceramic or tough
30. hich guarantee total efficiency If during normal use of the product defective or badly working particulars should be detected the replacement of such particulars will be free of charge ex dealer who made the sale TERRITORIAL EXTENSION OF THE WARRANTY Italian territory VALIDITY The warranty is considered valid on the condition that 26 The purchaser forwards the inspection report and warranty validation copy 2 filled in completely within 8 days from the date of validation of the warranty The purchase date must be validated by the possession of a valid fiscal document issued by the dealer 27 The appliance is used as prescribed in the instructions manual provided with all products 28 The boiler is installed in compliance with the Standards in force with regard to the prescriptions contained in the installation use and maintenance manual relating to the product by qualified staff in possession of the legal requisites M D n 37 dated 22 January 2008 29 The client is in possession of the documentation which certifies its eligibility filled in in all its parts a INSTALLATION REPORT filled in by the installer b INSPECTION REPORT AND VALIDATION OF THE WARRANTY filled in by the customer the dealer and an Extraflame S p A authorised after sales centre 30 The warranty document filled in and accompanied by the purchase fiscal document issued by the dealer must be kept and shown to staff of the EXTRAFLAME S p A Technical Aft
31. installation must guarantee easy access for cleaning the appliance itself discharge gas pipe and flue 10 6 NATIONAL REGIONAL PROVINCIAL AND TOWN COUNCIL REGULATIONS It is necessary to bear in mind all laws and national regional provincial and town council Standards present in the country the appliance has been installed PELLETS AND FEEDING 11 PELLETS AND FEEDING The pellets used must comply with the features described by the Standard 4 O NormM 7135 DIN plus 51731 UNI CEN TS 14961 Extraflame recommends the use of pellets with a diameter of 6mm with its products To guarantee combustion without problems the pellets must be kept in a dry place We recommend the use of pellets with diameter of 6mm with our products See the images for feeding pellets Open the tank lid and load the pellets using a scoop In the event of the inserts only load when the machine is off and cold by extracting it from the compartment In the event of installation with feeding kit optional the machine must not be extracted figure 19 19 HSI IDN3 12 PRODUCT FUNCTIONALITY 12 1 CONTROL BOARD figure 20 P1 c ON OFF BUTTON P2 H20 TEMPERATURE r gt REGULATION OF FUNCTIONING POWER D r gt DISPLAY OF THE VARIOUS TEXT MESSAGES 2 DISPLAY OF THE POWER 12 2 DISPLAY ICONS KEY Indicates the presence of an alarm On indicates the presence of an alarm Off indicates the absence of alar
32. ion chamber is dirty Check cleanliness of the fumes pipe and the combustion chamber The flue exhaust pipe is blocked Check the mechanical pressure switch air side DEPR SENSOR flow sensor faulty the water in the boiler has exceeded 95 C Possible air in the system H20 OVERTEMP Insufficient circulation contact after sales centre No or inadequate safety zone Possible pump anomaly the system pressure read by the pressure switch is too low MINIMUM Possible presence of air in the system PRESSURE ALARM Possible lack of water or leaks due to anomalies in some system component contact after sales centre Switch off the machine wait for complete cooling and repeat the ignition I cycle TRAPDOOR BLOCK The automatic cleaning of the burn pot results blocked if the problem persists the reset operations must be carried out by an authorised technician WATERPROBE H20 probe failure DISPLAYS 37 HSI IDN3 25 WARRANTY CONDITIONS EXTRAFLAME S p A with offices in via dell Artigiananto 12 Montecchio Precalcino VI guarantees this product for 2 two YEARS from purchase date for manufacturer and material faults The warranty becomes void in case the defect of conformity is not filed with the dealer within two months from date of its finding The responsibility of EXTRAFLAME S p A is limited to the supply of the appliance which must be perfectly installed following the indications contained in the appropriate man
33. locking does not occur as soon as the water temperature drops below the pre established parameters the boiler will switch back on the pump activates for a brief period in a way to prevent blockage of the same 24 ALARMS check the calibration of pellet regulation If this cannot be solved contact an Check hermetic door closure Check hermetic closure of the ash drawer Check cleanliness of the fumes pipe and the combustion chamber Check cleanliness if the air supply pipe and the flow sensor The door is not closed correctly The ash drawer is not closed correctly The combustion chamber is dirty The flue exhaust or air supply pipe is blocked Check for the presence of pellets in the feed box Regulate the pellet flow Check the procedures described in the Ignition chapter Take the boiler to OFF conditions using key 1 and repeat the procedure BLACK OUT NOIGN No current during the ignition phase described in the Ignition chapter The pellet feed box is empty Check for the presence of pellets in the feed box NO PELLETS No pellet feed Adjust pellet flow see Pellet feed adjustment The motor reducer does not feed pellets The pellet feed box is empty NO IGNITION Pellet feed calibration inadequate The door is not closed correctly Check hermetic door closure DEPR ALARM The ash drawer is not closed correctly Check hermetic closure of the ash drawer The combust
34. ms Flashing indicates the deactivation of the depression sensor T H20 On H20 T lower than desired set Off 20 T higher that set point set Ign plug Off ign plug active On ign plug deactivated Flashing Ignition phase Chrono Indicator on Chrono on Indicator off Chrono off stby the LED is always activated by default 9 not used 20 It indicates functioning of the fumes motor Off fumes motor not working On fumes motor working Flashing breakdown 1 Pump inside the boiler h Off pump not running On pump running not used not used Input STBY status Off open contact On closed contact Ignite with the motor reducer functioning When the motor feeds the LED switches on When the motor does not feed the LED switches off PRODUCT FUNCTIONALITY Extraflame has an optional additional board that allows the boiler the following further functions when managing the system The table below indicates the various possibilities that the optional can offer Puffer pump or 4th heating area management Anti legionella management for DHW storage DHW storage chrono management v 13 FUNCTIONING CYCLE 13 1 BASIC INSTRUCTIONS The following recommendations must be followed the first times the stove is ignited It is possible that slight odours are produced due to the drying of the paints and silicones used Do not remain in the environment for long periods
35. municates directly with the installation room even if the air is withdrawn from outside through a pipe The air flow can also be INSTALLATION obtained from an adjacent room as long as the flow takes place freely through permanent openings communicating with the outside The adjacent room with respect to the installation room must not be put in depression with respect to the external environment by means of reverse draught caused by the presence of another used appliance or intake device in such room The permanent openings in the adjacent room must comply with the above described requisites The adjacent room cannot be set up as garage storage for combustion material or activity with danger of fire 10 5 INSULATION FINISHINGS COVERING AND SAFETY RECOMMENDATIONS The coverings independently from the materials from which they are made must constitute a self supporting construction with respect to the heating block and not be in contact with it The cross members and finishings in wood or combustion materials must be positioned outside the hearth radiation area or adequately insulated If coverings in combustion material or sensitive to heat exist in the space above the generator an insulating and non combustible protection diaphragm must be inserted Elements in combustible or inflammable material like wooden furniture curtains etc directly exposed to the hearth radiation must be positioned at a safe distance The appliance
36. must be realised in order not to present scales or deposits storage points In case of more heat generators which feed the same plant or the same secondary circuit each heat generator must be connected directly to the expansion vessel or plant expansion vessels unit altogether dimensioned for the total volume of water contained in the same plant or the same independent circuit Where it is necessary to separate the individual heat generator from the expansion vessel or expansion vessels unit a three way tap must be applied on the connection piping between the generator and the vessel in order to ensure in every position the connection of the generator with the expansion vessel or with the atmosphere The expansion vessels the connecting pipes the bleed pipes and drain pipes must be protected from freezing where this phenomenon occurs The solution used for this purpose is described in the design Commissioning checks Before connecting the boiler a wash all system piping in order to remove any residues which might compromise the correct functioning of certain system components pumps valves etc b check to verify that the flue has adequate draft is not narrowed and that other appliances do not discharge into the flue This is to prevent unexpected power increases Only after this control can the chimney fitting between the boiler and flue be mounted It is recommended to control the fittings with pre existing flues Feeding water
37. nction is always active from the factory led on and the STBY clamp leaves jumpered contact closed 14 1 ADDITIONAL THERMOSTAT FUNCTIONING WITH STBY ACTIVE When the contact or external thermostat is not satisfied open contact temperature reached the stove will switch off As soon as the contact or external thermostat passes to the not satisfied status closed contact temperature to reach it will re ignite Nota bene stove functioning depends on the temperature of the water inside the same and relative factory restrictions set If stoveisin HOFF watertemperature reached any additional contact or thermostat request will be ignored 21 HSI IDN3 14 2 ADDITIONAL THERMOSTAT INSTALLATION Switch the appliance off using the master switch positioned on the rear of the stove Remove the plug from the socket Refer to the electrical layout to connect the two thermostat cables onto the relative clamps positioned don the rear of the machine one is red and the other black STBY clamp The STBY and AUX clamps can be noted in the diagram below Every model can have a different position of the relative clamps in the rear of the machine The image is given as an example AUX STBY figure 21 15 AIR DISCHARGE FUNCTION Thefunction allows to vent the air from the product To activate the procedure press the P1 and keys at the same time and insert the password 77 Confirm using the P5
38. ning 00 05 10 15 20 25 3 bar safety valve integrated into the thermo product Minimum and maximum pressure pressure Flow rate m h switch integrated into the thermo product Load unload cock Heat exchanger water content I Tests performed using wooden pellets as fuel certified according to ONORM M7135 DIN PLUS The data given above is indicative and not binding The manufacturer reserves the right to make any modifications in order to improve product performance D 6 8 9 TECHNICAL FEATURES 11 HSIIDNA LUCREZIA IDRO 1 Pump integrated in the thermo product with 5 m head es 2 Volume of expansion vessel integrated 2 into thermo product 1 4 3 bar safety valve integrated into the Es thermo product y Minimum and maximum pressure 5 pressure switch integrated into the yes thermo product Load unload cock 6 SAFETY DEVICES Circuit board intervenes directly by sending the product into alarm conditions until complete cooling in the event of breakage of flue gas motor pellet feed motor breakage black out if more than 10 seconds no ignition Door micro switch With the door open the burn pot system functioning is blocked Flow sensor in the event of inadequate air flow it takes the machine to alarm conditions 2 5 A fuse they protect
39. not exceeded Connection between the power supply unit and the valve must be free from interceptions The pressure upstream from the cooling circuit must be at least 1 5 bar Safety valves The load capacity of the safety valve must allow the discharge of a quantity of vapour not lower than Q 0 58 kg h where Q is the useful outlet power to the generator water expressed in kilowatt The diameter of the minimum net transversal section of the valve inlet must not be lower than 15 mm The valve load pressure equal to the calibration pressure increased by the overpressure cannot exceed the maximum exercise pressure of the heat generator The designer must check that the maximum pressure existing in every point of the system does not exceed the maximum exercise pressure of its every component safety valve must be connected to the highest part of the heat generator or outlet pipes immediately near the generator The length of the pipes route included between the attachment to the generator and the safety valve must not be higher than 1 m The connection piping of the safety valve to the heat generator must not be traceable and must not present in any point section lower to the inlet of the safety valve or the sum of the inlet sections in case of more valves under the individual pipe The discharge piping of
40. o display the water pressure 12 SAFETY DEVICES 6 1 INSTALLATION AND SAFETY DEVICES The installation relative system connections commissioning and inspection of correct functioning must be carried out perfectly in total compliance with Standards in force both national regional and municipal as well as these instructions For Italy installation must be carried out by professionally authorised staff Ministerial Decree dated 22 01 08 n 37 Extraflame S p A declines all responsibility for damages to objects and or persons caused by the system 6 2 SAFETY DEVICES FOR CLOSED VESSEL SYSTEM According to the UNI 10412 2 2006 Standard in force in Italy the closed systems must have safety valve pump control thermostat acoustic alarm activation thermostat temperature indicator pressure indicator acoustic alarm regulation automatic circuit breaker switch automatic circuit breaker block switch block thermostat circulation system expansion system safety dissipation system incorporated with the generator with thermal safety valve self activated whenever the appliance does not have atemperature self adjustment system 6 3 DISTANCES OF SAFETY DEVICES ACCORDING TO THE STANDARD not Component On the machine or Temperature safety sensors exceeding 30 cm Missing devices because not Not exceeding one metre on as per standard the flow pipe The temperature safety sensors must be in place on the machine at a dis
41. re programmed the function must be activated press key amp press the P3 key until SET REGULATIONS is displayed Press P5 key to access the menu lt 02 displays ENABLE CHRONO press the P2 or key to activate the chrono ON or deactivate it OFF to exit and memorise press the P1 key several times Nota bene When the weekly programmer is active the LED of the relative icon will switch on on the control board 16 2 2 2 2 PELLET SETTING the following menu allows to increase or decrease the flow of pellets during product functioning NV Procedure Once the chrono is programmed activate the function press gt press the P3 key until SET REGULATIONS is displayed key to access the menu key to select PELLET key to regulate the values as a 4 Press press the press the percentage Or to exit and memorise press the key several times 24 16 3 STATUS The menu allow to display the boiler status M 2 Procedure press key press the key until STATUS is displayed Press P5 key to access the menu or key to see the status to exit press key several times press the st1 t flue gas st2 auger st3 fumes motor revs st4 minutes st5 t 2 st6 flow st7 real power st8 t inlet air st9 t heated s
42. reen To go back press P3 To exit press key P1 OExtraflame STATUS 1 LP30 MOTOR umm OUT 2 PEL MOTOR icon 4 OIExtraflame STATUS 2 LP30 REVS FUMES T H2O e IGN PLUG 19 7 SET USER The set user menu offers the following possibilities set clock allows regulation of the time and date set chrono allows to program 4 functioning time periods for the boiler with automatic switch ons and switch offs and setting of the desired water temperature for every time period language setting the desired language Italian English French German Spanish set heat exchanger programming of the start and end times of the automatic cleaning of the heat exchangers 19 7 1 SET CLOCK From the main screen turn P2 to select the icon Press P2 to confirm Turn P2 to select SET CLOCK Confirm pressing P2 Turn P2 to select the desired parameter Press P2 to enter modification mode Turn P2 to modify the value Press P2 to confirm and exit If you wish to exit without memorising press key P1 LP30 MENU STRUCTURE 31 HSI IDNA ChExtrafidarne USER MENU SET CLOCK SET CHRONO LANGUAGE SET HEAT EXCHANGER 19 7 2 CHRONO REGULATION OExtrafilame SET CLOCK SATURDAY Through regulation
43. resistance INSTALLATION COMBUSTION PRODUCT EVACUATION SYSTEMS Flue gas exhaust system independent from the appliance constituted by a fitting or smoke channel chimney or individual flue and chimney cap FORCED DRAUGHT Air circulation by means of the fan activated by electric motor NATURAL DRAUGHT Draught which is determined in a chimney flue for effect of the volume mass difference existing between smoke hot and surrounding atmosphere air without any mechanical intake aid installed inside it or at its peak RADIATION AREA Area immediately near the hearth in which the heat caused by combustion is diffused where no combustion materials must be present REFLUX AREA Area where leaking of the combustion products is verified from the appliance towards the installation room The installation must be preceded by checking the chimneys flues or unload terminals positioning of appliances similarly to Installation prohibitions Legal distances Limitations disposed by local administrative regulations or particular authority prescriptions Conventional limitations deriving from condominium regulations constraints or contracts 10 1 INSTALLATIONS ALLOWED Only appliances working in a sealed manner respect to the room or which do not place the room in depression respect to the external environment can exist or be installed in the room where the heat generator will be installed Appliances for cooking food and rela
44. rs Such area has different dimensions and configuration depending on the covering inclination angle It is therefore necessary to adopt the minimum heights indicated in the figure layouts below The chimney cap must not have mechanical intake means FLAT ROOF y 20cm Cor E 25 EB f ao J 150 U T Dan 5m l 5mg E 5m MEER r acc es 588 2 r CEPR gt 1 a Ut N figure 17 SLOPING ROOF Z REFLUX AREA figure 18 CHIMNEY CAPS DISTANCES AND POSITIONING Roof incli Ene visitat Minimum chimney height the ridge and the nation measured from outlet chimney 0 50 m over the ridge 10 4 CONNECTION TO EXTERNAL AIR INLETS The appliance must be able to use the necessary air to guarantee regular functioning through external air inlet The air inlets must comply with the following requisites 4 havea total free section of at least 80 cm mustbe protected by grates metal net or suitable protections as long as they do not reduce the minimum section stated in the previous point and positioned in order to avoid them being obstructed If the combustion agent air is withdrawn directly from outside through a pipe a downward bend must be mounted outside or a protection against the wind and no grates or similar must be positioned it is recommended that the air vent always com
45. s key P1 QExtraflame QExtraflame USER MENU SET CLOCK SET CHRONO LANGUAGE START 00 00 SET HEAT EXCHANGER E STOP 00 00 4 4 s cma Jide SET HEAT EXCHANGER LP30 MENU STRUCTURE 33 HSIIDN3 20 1 14 20 30 BOILER CLEANING Some images could be offset from the original model Maintenance operations guarantee correct functioning of the product through time Failure to comply with these operations can jeopardise the safety of the product The cleaning operations must be performed when the stove is completely cold 20 1 BURN POT CLEANING The burn pot is cleaned via a mechanical system at pre fixed intervals automatically by the boiler The figure below shows the burn pot The company recommends to remove any ash residue using a suction device at least once every two days figure 22 20 2 DOOR GASKET AND ASH DRAWER The gaskets guarantee the tightness of the boilerandits consequent good functioning These must be checked regularly if they should be worn or damaged they must be replaced immediately These operations must be carried out by an authorised technician N B For correct functioning the boiler must undergo routine maintenance by an authorised technician at least once a year If the power supply cable is damaged it must be replaced by the after sales service or by a
46. scharges with respect to the appliance combustion product outlet have to be reached the direction changes will have to realised using open bends not greater than 45 see figures below For the heat generator appliances equipped with electric fan for expelling combustion products the instructions below must be followed Insulating BI IR product 45 5 figure 8 lt 45 B x Flue Inspection figure 9 The horizontal routes will have to have a minimum upward slope of 3 The length of the horizontal route must be minimal however not longer than 3 metres Thenumber of direction changes including the one for effect of using the T element must not be more than 4 if 4 bends 16 are used use double wall piping with an internal diameter of 120 mm In any case the smoke channels must seal the combustion and condensate products and be insulated if they pass outside the installation room The use of counterslope elements is forbidden The smoke channel must allow the recovery of soot or be brushable The smoke channel must have constant section Any section changes are only allowed at the flue coupling It is forbidden to have other air supply channels and pipes for plant engineering especially if over sized transit inside the smoke channels The mounting of manual draught adjustment devices on forced draught appliances is forbidden 10 3 2 CHIMNEY OR INDIVIDUAL FLUE The chimney or
47. t court for any disputes WARRANTY CONDITIONS QUALITY CONTROL WARRANTY CONDITIONS 39 CIExtraflame Riscaldamento a Pellet EXTRAFLAME S p A Dell Artigianato 12 36030 MONTECCHIO PRECALCINO Vicenza ITALY Tel 0445 86591 1 Fax 0445 865912 http www lanordica extraflame com E mail info extraflame com Extraflame reserves the right to change the features and data stated in the following file at any time without forewarning in order to improve its products This manual cannot be considered as a contract for third parties This document is available at www extraflame it support
48. t10 mechanical pressure switch status 16 4 USER MENU 16 4 1 SET CLOCK This menu allows to adjust the clock and the date M 7 Procedure from the OFF status press the P5 key for 3 seconds 4 The stove will show SET TEMPERATURE lt Press the key several times until the USER MENU is displayed 4 Press the 5 key the stove will disolay SET CLOCK Press the 5 key the stove will show DAY press the P2 and key to regulate the exact day fr om Monday to Sunday the days will run in the small display LZ the stove will show HOURS press the Press the key and key to regulate the exact hour Press the key the stove will show MINUTES press the and key to regulate the minutes For the other values continue as indicated above consulting the table below To go back to selection of the hours press button 4 again or escape and confirm using button 1 16 4 2 SET CHRONO The function allows to regulate the ignition and switch off times and the setting of the water temperature for the programmed time periods The following table gives all weekly programmer function parameters USER PARAMETERS CONSENTS FOR VARIOUS DAYS D2 KEYS KEY After the first time period times have been programmed display D1 should show the day of the week in running mode If START PRG1 STOP PRG1 OF 0000 MONDAY PRG1 OFF SUNDAY PRG1 OFF ON OFF START
49. tance no greater than 30 cm from the flow connection Whenever the generators lack a device those missing can be installed on the generator flow pipe within a distance no greater than 1m from the machine The domestic heating appliances with automatic feeding must be supplied with a fuel block thermostat or be supplied with a cooling circuit set up by the appliance manufacturer The cooling circuit must be activated by a heat safety valve such to guarantee that the limit temperature set by the Standard is not exceeded Connection between the power supply unit and the valve must be free from interceptions The pressure upstream from the cooling circuit must be at least 1 5 bar ATTENTION THE COMFORT IDRO MODEL DOES NOT HAVE EXPANSION VESSEL AND PUMP AS PER STANDARD HYDRAULIC SYSTEM 7 HYDRAULIC SYSTEM Certain concepts referring to the Italian UNI 10412 2 2006 Standard are described in this chapter As previously described when installing all national regional provincial and town council Standards in force provided by the country in which the appliance has been installed must be complied with TYPE OF SYSTEM There are two different types of system open vessel system and closed vessel system The product has been designed and realised to work with closed vessel systems CLOSED VESSEL SYSTEM FOR AUTOMATIC LOADING APPLIANCES System in which the water it contains is not in direct or indirect communication with the atmosphere G
50. the safety valve must be realised in order not to prevent the regular functioning of the valves and not to cause damages to persons the discharge must flow immediately near the safety valve and be accessible and visible The diameter of the discharge piping must not however be lower than that of the outlet connection of the safety valve For diameter of outlet connection it is intended the minimum internal diameter on the valve outlet upstream of the eventual internal threading 13 HSI IDN3 Closed expansion vessel The vessel maximum exercise pressure must not be lower than the calibration pressure of the safety valve increased by overpressures characteristic of the same valve bearing in mind the eventual level difference between vessel and valve and the pressure generated by the functioning of the pump The capacity of the expansion vessel s is evaluated depending on the total system capacity as results from the project The closed expansion vessels must comply with the dispositions regarding the planning manufacturing evaluation of conformity and use for pressure appliances Intercepting objects or section decreases must be inserted practiced on the connection piping which can be constituted by system portions The insertion of a three way intercepting valve which allows connection between the vessel and the atmosphere for maintenance operations is allowed Such device must be protected against accidental manoeuvres The connection pipe
51. tive hoods without extractor are only allowed in kitchens 10 2 INSTALLATIONS NOT ALLOWED Inthe room where the heat generator will be installed the following must not pre exist or be installed hoods with extractor collective type ventilation pipes Should these appliances be in rooms adjacent communicating with the installation room the simultaneous use of the heat generator is forbidden where a risk exists of one of the two rooms being placed in depression respect to the other 10 3 CONNECTION TO THE SMOKE EVACUATION SYSTEM UNI 10683 2005 Standard 10 3 1 SMOKE CHANNEL OR FITTINGS To mount the smoke channels non flammable elements will have to be used ideal for resisting combustion products and their eventual condensing The use of flexible metal and asbestos cement pipes to connect the appliances to the flue is forbidden even for pre existing smoke 15 HSI IDN3 channels There must be continuity between the smoke channel and the flue so that the flue does not lean on the generator The smoke channels must not cross rooms where the installation of the combustion appliances is not allowed The mounting of the smoke channels must be carried out in order to guarantee smoke seal for the appliance functioning conditions limit the forming of condensate and avoid it being transported towards the appliance The mounting of horizontal routes must be avoided For appliances where ceiling or wall non coaxial di
52. uals and books provided with the purchased product and in compliance with the laws in force Installation must be performed by qualified staff under the responsibility of the person entrusting him who will assume complete responsibility for the definitive installation and consequent good functioning of the product installed EXTRAFLAME S p A cannot be held responsible for the failure to comply with such precautions WARNING The warranty is validated on the condition that The installation and relative connections of the plant have been carried out by professionally authorised staff in total compliance with the Standard in force M D n 37 dated 22 January 2008 in compliance with the Standards in force both national and regional as well as these instructions Testing has been carried out by an authorised Extraflame S p A After Sales Centre which assume the entire responsibility to have verified that the plant has been realised in compliance with the Standard in force by professionally qualified staff in compliance with the Standards in force and to have checked the good functioning of the installed product Once this has been verified the After Sales Centre will supply all the information for its correct use filling in and delivering a copy of the document which certifies the warranty undersigned by the client EXTRAFLAME S p A assures that all its products are manufactured with top quality materials and with manufacturing techniques w
53. y for 3 seconds chit using the key until 3rd time span not used USER MENU 4th time span not used display D2 shows Successively press the P5 key SET CLOCK will appear Press the key until LANGUAGE appears enter the sub menu by pressing ke PS select the language using the P2 or memorise and exit pressing the Let s set the weekly programmer M 27 Procedure 7 Press key P5 for 3 seconds shift using the P3 key until key display D2 shows USER MENU gt Successively press the key SET CLOCK will appear 16 4 4 HEAT EXCHANGER CLEANING The menu allows to program the cleaning times of the heat Press the key until SET CHRONO appears exchanger inside the boiler function only available with To enter programming press software version V1 and not successive versions M 22 5 5 AWE Procedure s Use buttons P2 or P3 to set 08 00 which corresponds to the ignition time of the 1st time period Press key 5 for 3 seconds shift using the key until display D2 shows USER MENU 4 Successively the LPS key SET CLOCK will appear Toconfirm and continue programming press thelP5 button Press the P4 button to go back to the previous parameter 4 Press the key until HEAT EXCHANGER Use buttons P2 or P3 to set 1 2 00 which corresponds to 27
Download Pdf Manuals
Related Search