Wonde Proud Technology
Contents
1. SWP REC Execute this command to enable automatically logging current position into the Description memory of the device according to the parameter Mode and corresponding conditions Sunk WP REC Tag Password Mode Time Distance Number of rite Format Times Record Basis Heading SWPEREC Taal Pasonord OK REC Tag Mode Time Distance Times Record basis Heading ERR REC Tag Error Code Error Response l N Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the Se device and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Q Disable Stop storing position data into flash memory 1 Time mode Parameters The position information is logged into the memory of the device according to the required time interval only integer can be used Effective parameters Range 1 65535 seconds Mode 2 Distance mode The position information is logged into the memory of the device according to the required distance in2. PWD PWD of the device Enable Disable 0 Disable the message on the LCD will be erased 1 Enable 2 USB the output format is following S TMSG Msg line 1 Msg line 2 Msg line 3 CR LF Display Options 0 Display the message permanently if WP TMSG is disabled then the message on the LCD screen would be erased 5 65534 seconds Duration of displaying message on the screen Msg line 1 ASCII format maximum length is 16 bytes The text should be put in start quote and end quote quote symbol If it is empty inside the quotes to indicate no text will be transmitted Msg line 2 ASCII format maximum length is 16 bytes The text should be put in start quote and end quote quote symbol If it is empty inside the quotes to indicate no text will be transmitted Msg line 3 ASCII format maximum length is 16 bytes The text should be put in start quote and end quote quote symbol If it is empty inside the quotes to indicate no text will be transmitted Enable disable beep on message arrival 0 Disable beep when the message arrival 1 Enable beep when the message arrival Enable disable the report for user deleting message 0 Disable report 1 Enable report 1 The device always returns the following OK TMSG Enable Disable Display Options Msg line 1 Msg line 2 Msg line 31 Enable disable beep on message arrival 2 Also it can be queried the parameters 3 If
3. 1 The Distance and Smart mode requires the GPS reception If the GPS reception is not stable then the accuracy will be decreased Record Basis is only available when mode is set to 1 Copyright Wonde Proud Technology 2007 All rights are reserved 22 of 58 WONDE PROUD TECHNOLOGY SWP CLREC Execute this command to erase all logging data from the memory of the device WP CLREC Tag Password S ERR CLRREC Tag Error Code Error Response l T Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it Tag is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Parameters Max 5 characters Password of the device Only correct password can access the device and change the configuration The minimum length of character is 4 Password E _ digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP CLREC 0000 Response OK CLREC Copyright Wonde Proud Technology 2007 All rights are reserved 23 of 58 WONDE PROUD TECHNOLOGY SWP DLREC a Execute this command to download request logging data from the memory of the Description ro evice WP DLREC Tag
4. Copyright Wonde Proud Technology 2007 All rights are reserved 6 of 58 WONDE PROUD TECHNOLOGY SSS ET 6 Parameter Format for Returning Messages The report string includes a series parameters indicating as following Unit ID DateTime Longitude Latitude Speed Heading Altitude Satellite Report ID Mileage Format for each returning parameters Unit ID The ID of the device Maximum length is 10 digits DateTime YYYYMMDDhhmmss GMT Longitude WGS 84 coordinate system Latitude WGS 84 coordinate system Speed 0 65535 km h Heading 0 360 degrees Altitude Parameter column Reserved currently showing 0 Satellite 0 12 Report ID xxx Different report ID indicates different meaning of each returning message Please refer to appendix for detailed description Please Note The above information is only for the returning string with Report ID parameter Copyright Wonde Proud Technology 2007 All rights are reserved 7 of 58 WONDE PROUD TECHNOLOGY 7 Command List of WP Commands Command Description WP UNCFG Set Read unit ID Password and PIN Code of the SIM card Copyright Wonde Proud Technology 2007 All rights are reserved 8 of 58 WONDE PROUD TECHNOLOGY 8 Command Description SWP UNCFG Execute this command to configure the unit ID unit password and PIN code of the Description SIM card WP UNCFG Tag Password Unit ID New Password
5. Invalid characters in dial sting Unknown Copyright Wonde Proud Technology 2007 All rights are reserved 56 of 58 WONDE PROUD TECHNOLOGY Error Code Description 103 Illegal MS 106 Illegal ME 107 GPRS services not allowed 111 PLMN not allowed 112 Location area not allowed 113 Roaming not allowed in this location area 132 Service option not supported 133 Requested service option not subscribed 134 Service option temporarily out of order 148 Unspecified GPRS error 149 PDP authentication failure 150 Invalid mobile class Copyright Wonde Proud Technology 2007 All rights are reserved 57 of 58 WONDE PROUD TECHNOLOGY SSS NN 10 About Wonde Proud Technology WondeX SPT100 series device is manufactured by Wonde Proud Technology Wonde Proud Technology provides advance solution for GPS related solutions including the various GPS components Automatic Vehicle Location AVL device data logger amp real time tracking devices Please contact us at the phone and fax number list below or visit our website for further product information Wonde Proud Technology Web site http www wondeproud com Tel 886 2 26968498 Fax 886 2 26968499 Address 4F No 100 Sec 1 Shin Tai Wu Rd Sijhih city Taipei county 22102 Taiwan R O C Copyright Wonde Proud Technology 2007 All rights are reserved 58 of 58 1 Low Battery Report WP LOWBATT PWD M
6. Remark o Positondaia SWPHGETLOCATION a osgrgesinsas swere OOOO OO 2 epiese BETRAG a overseas bwes SYS 4 Eemerseney contctrumber _SWerEMSS O O O O O OO 5 Unauthorized movement report WP EMOV 50 99 User defined report position SWP SETEVT ma N Copyright Wonde Proud Technology 2007 All rights are reserved 51 of 58 WONDE PROUD TECHNOLOGY 9 2 Returning Command Error List The error list will be indicating to ERR Code number Description o uow communication eror O O n Tms o 2 MEE ME Invalid command parameters GSM SMS base phone number or GPRS Server IP address not set pF 2 Unable to detect GSM signal 5 GSM Failed ce Unable to establish the GPRS connection 7 Download process interrupted 8 Voice busy tone Notes 1 All error codes can be appeared via serial port communication 2 Error code 1 2 or 3 could be sent back over the air communication or serial port communication 3 All error code will not be sent back to control center over GSM SMS communication even though the GSM SMS message is the primary communication type Copyright Wonde Proud Technology 2007 All rights are reserved 52 of 58 WONDE PROUD TECHNOLOGY ee ET 9 3 CMS Error List Error Code Description 1 Unassigned unallocated number 8 Operator determined barring 10 Call barred 21 Shor
7. WP ROAMING 0000 1 Example Response OK ROAMING 1 Copyright Wonde Proud Technology 2007 All rights are reserved 140f 58 WONDE PROUD TECHNOLOGY S WP GETLOCATION Execute this command to get current position of the vehicle WP GETLOCATION Tag Password Response Unit ID DateTime Longitude Latitude Speed Heading Altitude Satellite Report ID ERR GETLOCATION Tag Error Code Error Response l nS Please refer to appendix for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it Tag is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max Parameters 5 characters Password of the device Only correct password can access the device een and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP GETLOCATION 0000 Response 1010000001 20070313170020 121 123456 12 654321 45 233 0 9 0 1 The device returns the last valid GPS information upon request regardless the GPS reception The parameter of Number of Satellites is 0 if there is no GPS reception or GPS is not fixed Thus the parameter of number of satellite could be a refer
8. 5 32 Send a message to Control Center base on the primary communication type 64 Store this event into the device memory Ex Set to 36 means control center will receive the string with report ID 4 and the phone number of SMS 3 will receive the SMS emergency messages when the emergency button button 5 is pressed Ex1 Issue command WP EMSMS 0000 886123456789 0933733456 886987654321 886932400821 886910777777 24 Response OK EMSMS 886123456789 0933733456 886987654321 886932400821 886910777777 24 Ex Issue command WP EMSMS 0000 886123456789 0933733456 2 Response OK EMSMS 886123456789 0933733456 2 1 If control center option is selected in the EMSMS Mask parameter then the control center server will receive the following string with report ID 4 1010000001 20070313170020 121 123456 12 654321 45 233 0 9 4 The format for the SMS message to contact phone number is following Emergency Report Unit ID 1XXXXXXXXX Date Time YYYYMMDDHHMMSS Lon XXX XXXXXX Lat XXX XXXXXX Speed XXX Km h Satellites XX Copyright Wonde Proud Technology 2007 All rights are reserved 48 of 58 WONDE PROUD TECHNOLOGY WP ODSET Execute this command to set the Quick Dial phone numbers for quick dial function WP QDSET Tag Password QD1 QD2 QD3 QDMask Format WP QDSET Tag Password Response OK QDSET Tag QD1 QD2 QD3 QDMask ERR QDSET Tag Err
9. NMEA 0183 GPGGA GPGSA GPGSV GPRMC and GPVTG WP NMEA Tag Password Enable Disable S ERR NMEA Tag Error Code Error Response i Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it is helpful Tag to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Parameters Password of the device Only correct password can access the device seer and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Enable Q Disable Disable 1 Enable Ex Issue command SWP NMEA 0000 1 Response S OK NMEA GPGGA 094307 000 2503 6251 N 12138 9153 E 1 10 1 0 169 9 M 15 3 M 0000 56 GPGSA A 3 18 05 22 12 30 09 21 14 31 24 1 9 1 0 1 6 3B GPRMC 094307 000 A 2503 6251 N 12138 9153 E 0 00 110407 A 79 example GPGGA 094308 000 2503 6251 N 12138 9153 E 1 10 1 0 169 9 M 15 3 M 0000 59 GPGSA A 3 18 05 22 12 30 09 21 14 31 24 1 9 1 0 1 6 3B S GPRMC 094308 000 A 2503 6251 N 12138 9153 E 0 00 110407 A 76 GPGGA 094309 000 2503 6251 N 12138 9153 E 1 10 1 0 169 9 M 15 3 M 0000 58 GPGSA A 3 18 05 22 12 30 09 21 14 31 24 1 9 1 0 1 6 3B S GPRMC 094309 000 A 2503 6251 N 12138 9
10. PIN code Write Format Read WP UNCFG Tag Password Response OK UNCFG Tag Unit ID New Password PINCODE S ERR UNCFG Tag Error Code Error Response l Please refer to appendix 9 2 for detailed error code descriptions Password of the device Only correct password can access the device and change the configuration The minimum length of Password character is 4 digits maximum length of character is 10 digits It Parameters The tag could consist of number or character string which can be defined by user The returning message will include the same tag and T it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters supports numerical characters only Default password is 0000 a Unit ID Device identification number The maximum length is 10 digits Only integer can be used Default unit ID is 1000000001 Note The most left digit is reserved in which must be 1 N Ww New password of the unit Password 9 e PIN Code The PIN Code of the SIM card The effective range is 4 to 8 digits 0 Disable Ex Issue command WP UNCFG 0000 1000000002 Response Example OK UNCFG 1000000002 The SIM card will be locked by the TELCO if enter incorrect PIN code for 3 times then the PUK code is required Please contact the local TELCO to unlock the SIM card Note Copyright Won
11. WP LCEMSG is enabled then TMSG has the priority to display on the LCD The message of WP LCDMSG will be displayed when the TMSG is disabled or time interval is reached 4 Delete message Short press the C1 button then long press C1 button again to delete the message 5 When the user delete the message then the Enable Disable parameter automatically becoming Disable and the text will be remained in the command parameter when query the parameter of this command 6 The Enable disable beep on message arrival will be changed to O after the message arrival when you query the parameter 15 Add the function to show a owner message or unit ID to replace the GPS coordinates on the first menu WP LCDMSG PWD Enable Disable Text Message PWD PWD of the device Enable Disable 0 Disable display GPS coordinates 1 Enable Display unit ID to replace the latitude information and Owner message replaces the longitude information Text Message maximum length is 16 bytes if it is null then only unit ID will be displayed if this command is enabled 16 Displaying mode manipulate Rev28 and more WP MDSW PWD Enable Disable PWD PWD of the device Enable Disable Normal Pagee O 1 2 4 8 GPS page Dialing mode Phone book page Short message page 17 Add head message and Enable Disable a beep sound if alert for the S WP EMOV WP EMOV PWD SMS1
12. be the external one which connects to the router and the parameter GPRS_ServerPort should be the port number of the computer which is assigned by the router If the parameter GPRS ServerlPaddress is using Virtual IP address in the intranet then it will lead to the GPRS connection failure 10 If the device is configured under GPRS mode GPRS UDP TCP the device will send the acknowledgement for the receiving command or returning message back to the GMS SMS base phone number once the device receives the command from a GSM SMS phone number other than GSM SMS base phone number If the GSM SMS base phone number is not set then the device will take the parameters but will not returning any message back to GSM SMS base phone number or GPRS server 11 Please be aware that if the GSM base phone number is not set the device has following behaviors If the device receives any valid incoming command via GSM SMS the device will execute the command but all acknowledgements or returning message will NOT be sent and will be ignored If the unit is configured under GPRS mode GSM base phone number is set if the device receives any valid incoming GSM command from a phone number other than GSM base phone number then the device will execute this command and return all acknowledgements and returning messages back to the GSM base phone number 12 If this command is issued over GSM SMS please be aware the text length limitation of the GS
13. of 58 WONDE PROUD TECHNOLOGY Report This parameter is to define the actions when the conditions become Actions true The following actions are available 1 Logging When the defined report s conditions are true then the device will store the current GPS position information for the specify event into the memory 2 Polling When the defined report s conditions are true then the device will send the current GPS position information for the specify event back to the base station 3 Logging and Polling When the defined report s conditions are true then the device will store the current GPS position information for specific event into memory and send the event back to the base station as well Ex 1 Issue command WP SETEVT 0000 50 1 120 167453 28 649871 200 1 3 Response OK SETEVT 50 1 120 167453 28 649871 200 1 3 Ex 2 Issue command WP SETEVT 0000 25 Response OK SETEVT 25 1 20 145634 25 764956 500 2 1 Copyright Wonde Proud Technology 2007 All rights are reserved 33 of 58 WONDE PROUD TECHNOLOGY SWP CLEVT Execute this command to clear single all report settings OK CLEVT Tag Report ID ERR CLEVT Tag Error Code Error Response e Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag i
14. successfully communicate with SPT100 device the WP or wp prefix is required when issuing command and the lt CR gt is required for terminating the command line Throughout this document the lt CR gt char is omitted intentionally The response of the command is usually followed by the lt CR gt lt LF gt in the end of responding message Throughout this document the lt CR gt lt LF gt chars are omitted intentionally There are two types of the commands and responses will be seen through this documents as following 1 Two types of command acknowledgement Ex 1 Issuing commands configure the parameters for a command WP lt Command gt lt Tag gt lt Password gt lt Para gt lt Para gt lt Para gt lt CR gt lt LF gt OK lt Command gt lt Tag gt lt Para gt lt Para gt lt Para gt lt CR gt lt LF gt Ex 2 Querying command parameters read command parameters sw lt Command gt lt Tag gt lt Pwd gt lt CR gt lt LF gt OK lt Command gt lt Tag gt lt Para gt lt Para gt lt Para gt lt Para gt lt CR gt lt LF gt 2 Ask for positioning information The returning positioning string for WP GETLOCATION or WP TRACK will NOT include the lt command gt lt Tag gt in the beginning of the string message The positioning data will be displayed as described in the chapter 6 Please note All characters of returning acknowledgement will be in upper case Cop
15. 153 E 0 00 110407 A 77 SWP NMEA 0000 0 S OK NMEA Copyright Wonde Proud Technology 2007 All rights are reserved 40 of 58 Description WONDE PROUD TECHNOLOGY 1 While NMEA string is outputted via USB port of the device the error message will not come out via USB port Please disable output the NMEA string before doing any diagnostic for the device Copyright Wonde Proud Technology 2007 All rights are reserved 41 of 58 WONDE PROUD TECHNOLOGY SWP SPD Execute this command to enable the speeding event report If the vehicle speed is in Description the speeding range between minimum and maximum speed for the certain time period Duration then it will trigger the speeding report WP SPD Password Mode Min Speed Max Speed Duration Format WP SPD Tag Password OK SPD Tag Mode Min Speed Max Speed Duration SERR SPD Tag Error Code Error Response l a Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the ENRE device and change the configuration The minimum length of character is 4 digits maximum l
16. 933733456 886987654321 886932400821 886910777777 38 Ex2 Issue command WP EMOV 0000 886123456789 0933733456 1 Response OK EMOV 886123456789 0933733456 1 1 If control center option is selected in the EMOV Mask parameter then the control center server will receive the following string with report ID 5 1010000001 20070313170020 121 123456 12 654321 45 233 0 9 5 2 The format for the SMS message to contact phone number is following Moving Alert Unit ID 1XXXXXXXXX Date Time YYYYMMDDHHMMSS Lon XXX XXXXXX Lat XXX XXXXXX Speed XXX Km h Satellites XX Copyright Wonde Proud Technology 2007 All rights are reserved 45 of 58 WONDE PROUD TECHNOLOGY 3 The Moving Alert report only sends once this function will be disabled automatically If we need to enable the Parking function then we need to re enable the function by pressing and holding the Function Key 1 for 3 seconds Copyright Wonde Proud Technology 2007 All rights are reserved 46 of 58 WONDE PROUD TECHNOLOGY WP EMSMS Execute this command to set the emergency contact phone number up to 5 different numbers Once the emergency button is pressed then the emergency GSM message Description will be sent to the pre defined contact phone number The receiving message format for the contact phone numbers please refer to the Note section T WP EMSM
17. Action Read S WP SETEVT Tag Password Report ID OK SETEVT Tag ReportID Enable Disable Longitude Latitude Tolerance Response Zone Control Report Action SERR SETEVT Tag Error Code Error Response nap Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Format Password of the device Only correct password can access the device and change the configuration The minimum length of Password B _ character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 The identifier of individual report The report ID only can be assigned by the integers The device supports up to 50 event settings and the effective Id number is from 50 99 Parameters Enable 0 Disable The radius of the circle zone The effective range is from 50 to 65535 Tolerance meters 1 Inside Zone The event will be sent when the GPS coordinate is inside the defined zones 2 Outside Zone Zone Control The event will be sent when the GPS coordinate is outside the defined zones Copyright Wonde Proud Technology 2007 All rights are reserved 32
18. Error Code Error Response ae Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it Tag is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Parameters Max 5 characters Password of the device Only correct password can access the device esel and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP REBOOT 0000 Response OK REBOOT 1 Please re establish the direct connection after issuing the WP REBOOT command The physically unplug and re plug in the USB cable might be Nore necessary Copyright Wonde Proud Technology 2007 All rights are reserved 27 of 58 WONDE PROUD TECHNOLOGY SWP RESET or Execute this command to reset the device to factory default settings or pre set Description settings SERR RESET Tag Error Code Error Response a Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands Th
19. Execute this command to setup the local time The time of returning message will be Description based on the time zone setting The default time zone is the GMT time Format WP SETTZ Tag Password Sign Hour Minute Response OK SETTZ Tag Sign Hour Minute ERR SETTZ Tag Error Code Error Response oi Please refer to appendix 9 2 for detailed error code descriptions g Password of the device Only correct password can access the device and change the configuration The minimum length of Password Parameters character is 4 digits maximum length of character is 10 digits It The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Ta it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters supports numerical characters only Default password is 0000 ahead GMT time Sign behind GMT time Hour Offset hours Effective range is from 00 13 Offset minute based on 15 minutes basis Please select one of Minute following 00 15 30 45 Ex Issue command Example WP SETTZ 0000 08 00 Response OK SETTZ 08 00 Copyright Wonde Proud Technology 2007 All rights are reserved 50 of 58 WONDE PROUD TECHNOLOGY EE EE eee 9 Appendices 9 1 Report ID Description Report Descriptior
20. M message Copyright Wonde Proud Technology 2007 All rights are reserved 13 of 58 WONDE PROUD TECHNOLOGY S WP ROAMING Execute this command to enable disable GPRS roaming function This command does not affect GSM SMS roaming service If GPRS roaming function is disabled the device Description will automatically closed the GPRS session and all undelivered messages would be stored in the queue buffer Those undelivered messages would be sent out whenever the device returns the non GPRS roaming network p WP ROAMING Tag Password Enable Disable ormat WP ROAMING Tag Password OK ROAMING Tag Enable Disable S ERR NMEA Tag Error Code Error Response oe Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it is helpful Tag to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Parameters Password of the device Only correct password can access the device and change the configuration The minimum length of character is 4 Password E digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Enable 0 Disable GPRS roaming function Disable 1 Enable GPRS roaming function Ex Issue command
21. Password Start Date Time End Write command Format Date Time sw DLREC Tag 00007 For Write command Command acknowledgement OK DLREC Tag Start Date Time End Date Time Download task completes Download Completed Response For Read command OK DLREC number of logs start date enddate Ex OK DLREC 388 20070522074235 20070522074907 ERR DLREC Tag Error Code Please refer to appendix 9 2 for detailed error code descriptions Error Response The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the device and change the configuration The minimum length of character is 4 Password _ digits maximum length of character is 10 digits It supports numerical Parameters characters only Default password is 0000 The year month day hour minute and second of the starting date in local time or GMT Start Date Format of this parameter YYYYMMDDHHMMSS or 0 please refer to the Note section for detail The year month day hour minute and second of the ending date in local time or GMT End Date Format of this parameter YYYYMMDDHHMMSS or 0 please refer to the Note section for detai
22. S Tag Password SMS1 SMS2 SMS3 SMS4 rite Format SMS5 EMSMS Mask WP EMSMS Tag Password Response 0K EMSMS Tag SMS1 SMS2 SMS3 SMS4 SMS5 EMSMS Mask S ERR EMSMS Tag Error Code Error Response l i _ Please refer to appendix for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag Tag and it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the device and change the configuration The minimum length of Password character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 SMS 1 Set the emergency contact phone number 1 Parameters SMS 2 Set the emergency contact phone number 2 SMS 3 Set the emergency contact phone number 3 SMS 4 Set the emergency contact phone number 4 SMS 5 Set the emergency contact phone number 5 This setting is based on the bitwise operation This parameter can specify which quick dial buttons are available The bitwise definitions are following EMSMS Mask Q Disable 1 SMS 1 2 SMS 2 Copyright Wonde Proud Technology 2007 All rights are reserved 47 of 58 WONDE PROUD TECHNOLOGY 4 SMS 3 8 SMS 4 16 SMS
23. S TCP IP mode The downloading task could be resumed once the GPRS connection is re established Copyright Wonde Proud Technology 2007 All rights are reserved 25 of 58 WONDE PROUD TECHNOLOGY WP SPDLREC Execute this command to stop downloading process WP SPDLREC Tag Password OK SPDLREC Tag OK S ERR SPDLREC Tag Error Code Error Response ae Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it Tag is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Parameters Max 5 characters Password of the device Only correct password can access the device esel and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP SPDLREC 0000 Response OK SPDLREC 1 Once the downloading process gets interrupted the ERR 7 message will be Note sent out to the base station Copyright Wonde Proud Technology 2007 All rights are reserved 26 of 58 WONDE PROUD TECHNOLOGY WP REBOOT Execute this command to reboot the device All setting will be remained effective WP REBOOT Tag Password S ERR REBOOT Tag
24. SMS2 SMS3 SMS4 SMS5 EMOV Mask Enable Disable beep Text PWD PWD of the device Set the emergency contact phone number 1 Set the emergency contact phone number 1 Set the emergency contact phone number 1 Set the emergency contact phone number 1 Set the emergency contact phone number 1 EMSMS Mask This setting is based on the bitwise operation This parameter can specify which quick dial buttons are available The bitwise definitions are following SMS1 SMS2 SMS3 SMS4 SMS5 0 1 2 4 8 Disable SMS 1 SMS 2 SMS 3 SMS 4 16 SMS 5 32 Send a message to Control Center Base on the primary communication type Enable Disable beep 0 Disable beep 1 Enable beep Text message maximum length is 16 bytes The text should be put in start quote and end quote quote symbol If it is empty inside the quotes to indicate no text will be transmitted 18 Add the head function WP RPHEAD PWD Head Text PWD PWD of the device Head Text maximum length is 16 bytes The text should be put in start quote and end quote quote symbol If it is empty inside the quotes to indicate no text will be transmitted 19 Send text message from device to GPRS server WP DCMSG PWD Text PWD PWD of the device Head Text maximum length is 16 bytes The text should be put in start quote and end quote quote symbol If it is empty inside the quotes to indicate no tex
25. WondeX SPT100 Series Protocol Document Version 1 06 Status Preliminary Date 9 10 2007 WONDE PROUD TECHNOLOGY eee See General Notes All materials contained on this documentation is protected by the copyright law and may not be reproduced transmitting published or broadcast without the prior obtaining authorization of Wonde Proud Technology The documentation is provided for testing evaluation integration and product information purpose and it may contain deficiencies or inadequacies information of products This product is not intended for use in life support appliance devices or systems where a malfunction of the product can reasonably be expected to result personal injury Wonde Proud or its supplier will not be liable for any consequential direct indirect incidental punitive or other damages including without limitation damages for loss of business profits business interruption loss of business information or other pecuniary loss that arising out the use of or inability to use the documentation or product even if Wonde Proud has been advised of the possibility of such damages The customers using or reselling the product in such application do so at their own risk and agree to full indemnify Wonde Proud for any damages resulting from illegal use or resale Subject to change without notice at any time Copyright Reproduction dissemination edition of this document or utilization of the content and communication form
26. and change the configuration The minimum length of Password B character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP IMEI 0000 Response OK IMEI 357258004284081 Copyright Wonde Proud Technology 2007 All rights are reserved 35 of 58 WONDE PROUD TECHNOLOGY WP SIMID Execute this command to query the identification number of the SIM card WP SIMID Tag Password OK SIMID Tag SIM card Identification No ERR SIMID Tag Error Code Error Response _ Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Parameters Max 5 characters Password of the device Only correct password can access the device and change the configuration The minimum length of Password B character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP SIMID 0000 Response OK SIMID 87109834789209748618 Copyright Wonde Proud Technology 2007 All rights are reserved 36 of 58 WONDE PROUD TECHNOLOGY SWPI VWT Ex
27. ask PWD PWD of the device Mask 0 Disable Default 1 Enable Buzzer When low alarm will sound a beep every 1 minute and 2 beeps before shut down caused battery no power Logging Buzzer Logging Polling Polling Buzzer Polling Logging Polling Logging Buzzer N OU B WN Note Report ID 40 Main power low report 2 Power on off report WP PRSET PWD Power on report power off report PWD PWD of the device Power on report 0 disable 1 logging 2 polling Power low report 0 disable 1 logging 2 polling Report ID 41 Device power off report Report Id 42 Device power on report 3 Power Saving Mode WP PSM PWD Mode Power Down Delay Sleeping Priority enable disable cyclic wake up Mode Added mode 3 mode 2 disable G Sensor detection Enable disable Cyclic wake up 0 Disable no GSM GPRS cyclic wake up no report only GPS cyclic wake up 1 wake up only no sleeping report 2 Sleeping report only no GSM GPRS cyclic wake up only GPS cyclic wake up 3 Cyclic wake up and send sleeping report Note Report ID 37 Sleeping report 4 Switch for external power source to power on the device S WP EXPWR PWD Enable Disable external power on the device Enable Disable backlight function PWD PWD of the device Enable Disable external power on the device 0 Connect the power source to the USB would NOT power on the device 1 Connect the power source to t
28. at as well as giving to other without authorization are prohibited Offenders will be held liable for payment of damages Copyright Wonde Proud Technology 2007 All right are reserved Copyright Wonde Proud Technology 2007 All rights are reserved 2 of 58 WONDE PROUD TECHNOLOGY ee ee ET Table of Content 1 Introduction to WondeX SPT100 Protocol Document 4 Zi WEST Sy EE N EE es 4 DM ele COC NG EES oi DE E EE RE eg ER ee er cases ER ee ee ee ie 5 ME Soe SWP Conan OE OE OE EE Ed 5 5 Supported Communication TYDES iese ese ee ER RR Re Re ee ee ee ee ee ER Re ee ee ee ee 6 6 Parameter Format for Returning Messages sees ese DEE ee Es ee en ee be ure Ee 7 T Command Listol WP Commands RE EE EE NEEE ENEE NAN ER aE EG ee 8 6 Commie Ese DIO de ee ee E eT 9 EE ies ME OE EE EE N EE EE EE OE EE EE EO N 51 1 Report If Des OM er ern ne E E ER ee ee 51 9 2 Retuming Command Eror LIST ei DE EER tase Oe EE Ee ER AO Ee ei 52 EMM Errof L ee ee E E A ne Ree ee ee ee De 53 9 4 CME Error do EE NE EE EO N EE EE N eN 56 LO About W onde Proud leehaolo oi oe SE EG ei ee be GE ER ee ie re tei EN 58 Copyright Wonde Proud Technology 2007 All rights are reserved 3 of 58 WONDE PROUD TECHNOLOGY EE ee eg RNR 1 Introduction to WondeX SPT100 Protocol Document This document describes the protocol of the WondeX SPT100 devices This document is used for all communications information between the base station controller center and t
29. calls 1 Enable incoming call filter 2 Enable outgoing call filter 3 Enable incoming and outgoing call filter 4 Reject all incoming and outgoing calls Incoming call 1 Set the incoming filter phone number 1 Incoming call 2 Set the incoming filter phone number 2 Incoming call 3 Set the incoming filter phone number 3 Outgoing call 1 Set the outgoing filter phone number 1 Outgoing call 2 Set the outgoing filter phone number 2 Outgoing call 3 Set the outgoing filter phone number 3 7 Choice between GPRS report and or voice call on C1 C2 C3 button WP QDSET PWD QD1 QD2 QD3 QDMask for Voice call QDMask for GPRS report Enable Disable pickup hang up beep for QD function PWD PWD of the device QD1 QD2 QD3 Quick dial set up to 3 sets QDMask for Voice Call 1 QD1 2 QD2 4 QD4 QDMask for GPRS Report 1 OD1 Report ID 43 2 QD2 Report ID 44 4 QD4 Report ID 45 Enable Disable pickup hang up voice call 0 Disable 1 P to Pick up 2 Only C1 hang up 4 Sound a beep when C1 C2 or C3 button is pressed 8 Add a new function to adjust the voice volume by default 50 WP VOL PWD Set Volume Enable Disable the adjustment of voice volume by button PWD PWD of the device Set Volume value between 0 100 0 no voice 100 loudest voice Enable Disable the adjustment of voice volume by button 0 Disable the volume adjustment by button 1 Enable the volume adjustment by butt
30. ck to the base station when one of the following condition is satisfied a Heading direction parameter is changed beyond assigned degrees b Required BOTH Time AND Distance Interval are satisfied Copyright Wonde Proud Technology 2007 All rights are reserved 21 of 58 WONDE PROUD TECHNOLOGY eee 9 Heading OR Time OR Distance The position information is sent whenever one of the following condition is reached a When the Heading direction parameter is changed beyond assigned degrees b Required Time Interval is reached c Required Distance Interval is reached Time Specify elapsed time interval to report current position Default value is 0 The effective range please refer to the mode parameters option 1 Time mode Distance Specify elapsed distance interval to report current position Default value is 0 The effective range please refer to the mode parameters option 2 Distance mode Number of Frequency number of times the report needs to be sent Effective Times range is from 0 65535 Set 0 indicating Continuously logging Record 0 Position information is sent only GPS signal available Basis 1 Position information is sent regardless the GPS signal reception Ex Issue command WP REC 0000 1 5 0 0 0 Response OK REC 1 5 0 0 0 This function follows the FIFO first in first out algorithm algorithm
31. ctual voltage level of the interval backup battery this command must be issued via remotely communication such as GSM GPRS without the device connecting to a computer Copyright Wonde Proud Technology 2007 All rights are reserved 38 of 58 WONDE PROUD TECHNOLOGY SWP VER T Execute this command to query the current firmware and hardware version of the Description device WP VER Tag Password OK VER Tag firmware version hardware version ERR VER Tag Error Code Error Response ie Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it Tag is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Parameters Max 5 characters Password of the device Only correct password can access the device and change the configuration The minimum length of character is 4 Password E digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP VER 0000 Response OK VER 1 001 3 Copyright Wonde Proud Technology 2007 All rights are reserved 390f 58 WONDE PROUD TECHNOLOGY SWP NMEA Execute this command to enable the outputting the NMEA string through serial port The NMEA format is
32. de Proud Technology 2007 All rights are reserved 9 of 58 WONDE PROUD TECHNOLOGY SWP COMMTYPE od Execute this command to set the primary communication type and its related Description parameters WP COMMTYPE Tag Password CommSelect SMSBasePhonel CSDBasePhonel GPRS APNI Formal GPRS_Username GPRS_Password GPRS_ServerlPAddress GPRS ServerPort GPRS Synclntervall GPRS DNS WP COMMTYPE Tag Password OK COMMTYPE CommSelect SMSBasePhone CSDBasePhone Response GPRS APNLIGPRS Usernamel GPRS Password GPRS ServerlPAddressl GPRS ServerPort GPRS Synclntervall GPRS DNS S ERR COMMTYPE Tag Error Code Error Response l oe Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag Tag and it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the seed device and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Set primary communication type Parameters 0 Serial port communication Note Support COM numbers COM 1 COM 199 auto detectable CommSelect 1 GSM SMS comm
33. e will stop executing this function automatically Copyright Wonde Proud Technology 2007 All rights are reserved 37 of 58 WONDE PROUD TECHNOLOGY SWP TEST Execute this command to test major modules status and the voltage level of the Description device Command Write WP TEST Tag Password Format OK TEST Tag Status Voltage Level 0 No Error occurs 1 GSM Error Response Status 2 GPS Error Parameters Voltage peel The voltage level of the internal backup battery eve ERR TEST Tag Error Code Error Response o Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Parameters Max 5 characters Password of the device Only correct password can access the device and change the configuration The minimum length of Password character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP TEST 12345 0000 Response OK TEST 12345 3 3 9 1 If the device connect to a computer by USB cable then the voltage level always shows 4 2V approximately estimation Note 2 In order to get a
34. ecute this command to enable voice wiretapping function Once the device receives this command then it will call out to the assigned phone number automatically The device will enable microphone and disable speaker function once Description the phone line is connected Thus the user s conversation will be monitored by the assigned phone number This function will be disabled automatically once the phone line has been hung up WP VWT Tag Password Phone number OK VWT Tag Phone number S ERR VWT Tag Error Code Error Response _ Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Parameters Password of the device Only correct password can access the EE device and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Phone The specific phone number which the device will call out This phone x Issue command Example WP VWT 0000 886932400821 Response OK VWT 886932400821 1 If the device fails to establish the phone line i e gets the busy tone for 5 times Note the devic
35. ence to check whether there is GPS reception or not Copyright Wonde Proud Technology 2007 All rights are reserved 15 of 58 WONDE PROUD TECHNOLOGY SWP TRACK a Execute this command to enable automatically reporting current position to the base Description l n station according to the parameter mode and related conditions WP TRACK Tag Password Mode Time Distance Number rite Format of Times Track basis CommSelect Heading WP TRACK Tag Password OK TRACK Tag Mode Time Distance Times Track basis CommSelect Response Heading ERR TRACK Tag Error Code Error Response na Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the device and change the configuration The minimum length of Password _ character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Mode 0 Disable Stop tracking 1 Time mode The position information is sent to the base station according to Paeancters the required time interval only whole n
36. ength of character is 10 digits It supports numerical characters only Default password is 0000 Mode 0 Disable 1 Logging Parameters 2 Polling 3 Logging and Polling Min Speed Set Minimum Speed Max Speed Set Maximum Speed Duration The parameter defined the time duration to activate the speeding report For logging 15 65535 seconds For polling 15 65535 seconds For logging and polling 15 65535 seconds Copyright Wonde Proud Technology 2007 All rights are reserved 42 0f 58 WONDE PROUD TECHNOLOGY Ex Issue command WP SPD 0000 3 100 200 15 Response OK SPD 3 100 200 15 Copyright Wonde Proud Technology 2007 All rights are reserved 43 of 58 WONDE PROUD TECHNOLOGY SWP EMOV Execute this command to set up the contact number for detecting unauthorized movement Activation deactivation by depressing the Function Key 1 for 3 er seconds This command takes effect after 3 minutes of function activation If this Description function has not been disabled after 1 minute of event triggering selective actions will be executed The receiving message format for the control center and contact phone numbers please refer to the Note section ak S WP EMOV Tag Password SMS1 SMS2 SMS3 SMS4 rite Format SMS5 EMOV Mask sPsEMOv TagkPassnord Response OK EMOV Tag SMS1 SMS2 SMS3 SMS4 SMS5 EMOV Mask ERR EMOV Tag Error Code Er
37. etes the required task it goes to sleeping mode according to the Power Down Delay interval if all conditions of entering sleeping mode remaining true 4 If there is no wake up condition detected the device wakes up every 60 minutes and stay on for 1 minute to update the GPS information 5 If WP TRACK or WP SPD command are executing device will not going to sleeping mode until the command is disabled 6 When set to mode 2 the logging function will not be executed during the sleeping duration except the device waking up or power saving mode is disabled Copyright Wonde Proud Technology 2007 All rights are reserved 30 of 58 WONDE PROUD TECHNOLOGY 7 Please refer to the power saving mode diagram as following Power saving mode Wake up conditions conditions are true GPS wakes up are true fel ini Power saving mode Normal Mode PS on GSAUGPRS on t conditions are true Sleeping mode Mode 1 GPS Off GAM GPRS on Mode 2 GPS off x GSM idle state GPRS off Power Down Delay Sleeping duration Power Down Delay 60 min approximately Normal mode mleeping mode Copyright Wonde Proud Technology 2007 All rights are reserved 31 of 58 WONDE PROUD TECHNOLOGY SWP SETEVT Description Execute this command to set GEO Fencing event i WP SETEVT Tag Password ReportID Enable Disable rite Longitude Latitude Tolerance Zone Control Report
38. he SPT100 devices The document includes command syntax with full acknowledgement of sending receiving messages upon request also the features functionalities of each command Hence this document covers all information which you need to design build application software that uses the SPT100 as the devices 2 Version History Version Description Supported Supported Firmware Version Hardware Version 1 00 Initial commands V0 006 or above Added hardware version information to the 1 02 V1 002 or above V1 or above WP VER command 03 1 Modified the effective range for Sync V1 002 or above V1 or above message Added querying number of logs in the V1 003 or above V1 or above memory for WP DLREC command Modified the length of GSM SMS alert messages for WP EMOV and V1 003 or above V1 or above WP EMSMS command Modified the command format for WP PSM Power Saving Mode adding the power down delay and V1 003 or above V3 or above Sleeping Priority Add mode 2 for deep sleeping mode Correction of the Sync header definition Add CommSelect and Heading conditions for the WP TRACK command V1 006 or above V3 or above Add Heading condition for WP REC command Copyright Wonde Proud Technology 2007 All rights are reserved 4 of 58 WONDE PROUD TECHNOLOGY RR EE ee ee 3 Related Documents 1 SPT100 Operation User Manual 4 Syntax of SWP Commands In order to
39. he USB could wake up the device 2 While disconnecting the power source from the USB port the device will power off the device connecting power source to the USB could wake up the device Enable Disable backlight function 0 Default backlight function 1 Backlight always on 5 Choice between voice call and or SMS and or GPRS report if SOS button pressed WP EMSMS PWD SMS1 SMS2 SMS3 SMS4 SMS5 EMSMS Mask Text message Enable disable beep when press button to start the emergency process PWD PWD of the device SMS1 SMS 2 SMS3 SMS 4 SMS 5 pre defined phone numbers to receive GSM SMS report EMSMS Mask 0 Disable 1 SMS 1 2 SMS 2 4 SMS 3 8 SMS 4 16 SMS 5 32 Send a message to Control Center base on the primary communication type 64 Store this event into the device memory 128 Make a phone call to the SMS 1 Text message maximum length is 16 bytes The text should be put in start quote and end quote quote symbol If it is empty inside the quotes to indicate no text will be transmitted Enable disable beep when press button to start the emergency process 0 Disable 1 Enable 6 Incoming and outgoing calls limitation Enabled disabled if disabled no display of dialing mode menu WP CIFR PWD mode incoming call 1 incoming call 2 incoming call 3 outgoing call 1 outgoing call 2 outgoing 3 call PWD PWD of the unit Mode 0 Accept all incoming and outgoing
40. is tag could be left as empty if it is not used Parameters Max 5 characters Password of the device Only correct password can access the EUO device and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Ex Issue command Example WP RESET 0000 Response OK RESET The Unit ID parameter will remain the same after executing this command Other settings will be set back to factory default Note If the password is forgotten then the device can accept the last 6 digits of IMEI No as password in order to reset the device successfully Copyright Wonde Proud Technology 2007 All rights are reserved 28 of 58 WONDE PROUD TECHNOLOGY SWP PSM Description Execute this command to enable the Power Saving Function of the device Format WP PSM Tag Password Mode Power Down Delay Sleeping Priority Response OK PSM Tag Mode Power Down Delay Sleeping Priority SERR PSM Tag Error Code Error Response _ Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it Tag is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Pass
41. l Copyright Wonde Proud Technology 2007 All rights are reserved 24 of 58 WONDE PROUD TECHNOLOGY Example Ex Issue command WP DLREC 0000 0 0 Response O0K DLREC 0 0 1010000001 20070313180520 121 123456 12 654321 45 233 0 8 1 1010000001 20070313181020 121 123456 12 654321 45 233 0 7 1 1010000001 20070313181520 121 123456 12 654321 45 233 0 8 1 1010000001 20070313182020 121 123456 12 654321 45 233 0 8 1 1010000001 20070313182520 121 123456 12 654321 45 233 0 8 1 1010000001 20070313183020 121 123456 12 654321 45 233 0 8 1 1010000001 20070313183520 121 123456 12 654321 45 233 0 8 1 Download Completed Note 1 If the download process is interrupted by any insertion command message then the error message ERR 7 is sent back to the base station 2 This command does not support resume function 3 The value 0 can be used for both parameters Start Date Time and End Date Time The corresponding actions are following Get all logs from the memory Download all logs from the specific Start Date Time to the last log in the Valid Date amp Time format memory Download all logs from the 1 log to Valid Date amp Time the date specify in the End Date Time format in the memory Get all logs between the Start Date Time and End Date Time Valid Date amp Time Valid Date amp Time format format 4 This command supports Resume function in the GPR
42. l is reached Heading OR Distance The position information is sent whenever one of the following condition is satisfied a Heading direction parameter is changed beyond assigned degrees b Required Distance Interval is reached Heading OR Time AND Distance The position information is sent back to the base station when one of the following condition is satisfied a Heading direction parameter is changed beyond assigned degrees b Required BOTH Time AND Distance Interval are satisfied Copyright Wonde Proud Technology 2007 All rights are reserved 17 0f 58 WONDE PROUD TECHNOLOGY 9 Heading OR Time OR Distance The position information is sent whenever one of the following condition is satisfied a When the Heading direction parameter is changed beyond assigned degrees b Required Time Interval is reached c Required Distance Interval is reached Time Specify elapsed time interval to report current position Default value is 0 The effective range please refer to the mode parameters option 1 gt Time mode Note The counter of Times will be displayed the how many times left while the command is executing when we query the command parameters Distance Specify elapsed distance interval to report current position Default value is 0 The effective range please refer to the mode parameters option 2 gt Distance
43. mode Number of Frequency number of times the report needs to be sent Effective Times range is from 0 65535 Set 0 indicating Continuously tracking Track Basis 0 Position information is sent only GPS signal available 1 Position information is sent regardless the GPS signal reception CommSelect Set the output communication channel 0 Serial port communication Note Support COM numbers COM 1 COM 199 auto detectable 1 GSM SMS communication 2 CSD Circuit Switched Data communication Reserved currently not support 3 GPRS UDP communication 4 GPRS TCP IP communication Heading The effective value is from 10 90 degrees Copyright Wonde Proud Technology 2007 All rights are reserved 18 of 58 WONDE PROUD TECHNOLOGY Issue command WP TRACK 0000 1 5 0 5 0 Response OK TRACK 1 5 0 5 0 1010000001 20070313170020 121 123456 12 654321 0 233 0 9 2 1010000001 20070313170025 121 123456 12 654321 0 233 0 9 2 1010000001 20070313170030 121 123456 12 654321 0 233 0 9 2 1010000001 20070313170035 121 123456 12 654321 0 233 0 9 2 1010000001 20070313170040 121 123456 12 654321 0 233 0 9 2 1 The Distance and Smart mode requires the GPS reception If the GPS reception is not stable then the accuracy will be decreased 2 Record Basis is only available when mode is set to 1 Copyright Wonde Proud Technology 2007 All rights are reserved 19 of 58 WONDE PROUD TECHNOLOGY
44. mum length is 16 bytes 25 Idle command if G sensor does not detect any movement within certain interval then send a idle report gt V1 007RevO2 WP IDLESET PWD Time Interval Mask PWD PWD of the device Time Internal 30 65535 seconds Mask 0 Disable 1 IDLE report logging 2 IDLE report polling 4 Moving report logging 8 Moving report polling 16 Enable Idle beep beep 32 Enable Moving beep Note Report ID 30 Detect the device entering IDLE Report ID 29 The G sensor is triggered during IDLE 26 Track commands for low speed gt V1 007Rev04 a WP LOWTRACK PWD Mode Speed Limitation Speed Duration Time Times Heading PWD PWD of the device Mode 0 Disable 1 Time 5 Heading 6 Time or Heading Speed Limitation 0 255 Km Hr Duration 0 65535 Seconds Time GPRS UDP TCP IP 5 65535 seconds Times Frequency number of times the report needs to be sent Effective range is from 0 65535 Set 0 indicating Continuously tracking Heading Direction 10 90 degree b SWP MIT PWD Time Time 0 65535 seconds
45. ng Sync message This parameter will not send any Sync message to the control center GPRS_DNS Domain Name Service IP address Please contact local ISP for the DNS IP address Please use the xxx xxx xxx xxx as the format for this parameter Default setting 168 95 1 1 Ex1 GPRS TCP with static WAN IP address Issue command S WP COMMTYPE 0000 4 internet 60 210 45 68 1050 30 168 95 1 1 Response OK COMMTYPE 4 internet 60 210 45 68 1050 30 168 95 1 1 Example Copyright Wonde Proud Technology 2007 All rights are reserved 11 of 58 Note WONDE PROUD TECHNOLOGY Ex2 GPRS TCP with dynamic Domain Name Service Issue command WP COMMTYPE 0000 4 internet serverDNSNAME 6080 30 168 95 1 1 Response S OK COMMTYPE 4 internet serverDNSNAME 6080 30 168 95 1 1 1 GPRS phone number i e 99 1 does not require for SPT100 device SPT100 will detect it by itself 2 If primary communication is GPRS then both parameters SMSPhone and CSDPhone are not required 3 The port number of ServerPort parameter must be opened for the control center software and not conflict with others port which is occupied by OS or other software 4 Please enable the GPRS service for the SIM card before start GPRS configuration Also please obtain related information such as Access Point Name APN user name if applicable and password if applicable for GPRS configuration SWP COMMTYPE command 5 The static IP add
46. on Note The currently volume if the volume has been adjusted by the user it will be showing in the second parameters when query the parameters of this command EX WP VOL 0000 O0K VOL 80 70 1 80 current volume level by command 70 currently volume level by user adjustment 9 G sensor status inside sync message Indicates in the last bit of Sync ID this function only available when the Power Saving Mode is on 10 Add ULOCK function lock the USB communication WP ULOCK PWD Enable Disable PWD PWD of the device Enable Disable 0 Disable Default 1 Enable 11 Add a new parameter for the VWT command Enable Disable Speaker S WP VWT PWD Phone number Enable Disable PWD PWD of the device Phone number the destination number which the device will dial Enable Disable 0 Disable speaker 1 Enable speaker 12 Remove the time from the first page and use a satellite icon instead Icon blink GPS is not fixed Icon not blinking GPS is fixed 13 Displaying for Pin code for security reason Function is like normal but the pin code will not show up regardless the PIN code is enable or disable 14 Text transmission the message will be displayed in the normal mode to replace the GPS coordinate WP TMSG PWD Enable Disable Display Options Msg line 1 Msg line 2 Msg line 3 Enable disable beep on message arrival Enable Disable the report for user deleting message
47. or Code Error Response coe Please refer to appendix for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag Tag and it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the Bear device and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits lt supports numerical characters only Default password is 0000 QD1 Set the quick dial number for the quick dial function button 2 Set the quick dial number for quick dial function button 3 Parameters Set the quick dial number for quick dial function button 4 This setting is based on the bitwise operation This parameter can specify which quick dial button is available The bit definitions are following Q Disable 1 QD1 2 QD2 4 QD3 Ex Set to 6 means QD2 button 3 and QD3 button 4 are available Pressing the button 1 QD1 will not take any action QDMask Ex Issue command Example WP QDSET 0000 886932400821 886937400841 0933765432 3 Response OK QDSET 886932400821 886937400841 0933765432 3 Copyright Wonde Proud Technology 2007 All rights are reserved 49 of 58 WONDE PROUD TECHNOLOGY SWP SETTZ
48. ress is required for the GPRS communication Sometimes the failure of GPRS connection is caused by the firewall setting enabled 6 Synchronization message format Data transmission by binary format typedef struct WORD SyncHeader WORD SynclD DWORD UnitID Syncstruct SyncHeader is always OXD7DO SynclD is the sequence number for the Sync message UnitID is the device identification number The base station could use this information to recognize the current holding dynamic IP for each device Ex received Synchronization message following OxDO 0xD7 0x1A 0x01 OxC7 0x54 0x44 0x3C SyncHeader OxD7 0xDO synclD 0x01 0x1A Decimal 282 UnitID Ox3C 0x44 0x54 OxC7 Decimal 1011111111 Copyright Wonde Proud Technology 2007 All rights are reserved 12 of 58 WONDE PROUD TECHNOLOGY in which must echo back exact synchronization string back to the device once the base station receives the synchronization message which was sent from the device to confirm the GPRS connection 8 The performance of the GPRS connectivity might be affected by the synchronization interval due to the TELCO policy for the dynamic IP address control The optimized synchronization interval needs to be tested in the local area in order to obtain the optimized synchronization interval cost effective 9 If the control center software is installed in a computer which is located in the Intranet then the parameter GPRS_ServerlPaddress should
49. ror Response l ee Please refer to appendix for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the Bied device and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Set the contact phone number 2 This setting is based on the bitwise operation This parameter can specify which quick dial buttons are available The bitwise EMOV Mask definitions are following Q Disable 1 SMS 1 Copyright Wonde Proud Technology 2007 All rights are reserved 44 of 58 WONDE PROUD TECHNOLOGY 4 SMS 3 8 SMS 4 16 SMS 5 32 Send a message to Control Center base on the primary communication type 64 Store this event into the device memory Ex Set to 36 means control center will receive the string with report ID 5 and the phone number of SMS 3 will receive a SMS alert when the unauthorized movement alert is triggered Ex Issue command WP EMOV 0000 886123456789 0933733456 886987654321 886932400821 886910777777 38 Response OK EMOV 886 123456789 0
50. rved se C Operation notsupponed SSS 308 vats POU moseporameter O OO rvatotoxtmode promoter o OM wense SIM PIN reduired sa penne ss smee SSCS me lm OO as smwog SS MAKE O SIM PIN2 required se smeer oS O memon SSCS O an mammon OS o aa wea S Copyright Wonde Proud Technology 2007 All rights are reserved 540f 58 WONDE PROUD TECHNOLOGY SIM not ready Unread records on SIM PS busy Invalid length SM BL not ready Invalid non hex char in PDU Copyright Wonde Proud Technology 2007 All rights are reserved 55 of 58 WONDE PROUD TECHNOLOGY ee ET 9 4 CME Error List Error Code Description Operation not allowed Operation not supported PH SIM PIN required PH FSIM PIN required PH FSIM PUK required SIM not inserted SIM PIN required SIM PUK required SIM failure SIM busy SIM wrong Incorrect password SIM PIN2 required SIM PUK2 required Memory full Invalid index Invalid characters in text string Dial string too long Invalid characters in dial string No network service Network timeout Network not allowed emergency calls only Network personalization PIN required Network personalization PUK required Network subset personalization PIN required Network subset personalization PUK required Service provider personalization PIN required Service provider personalization PUK required Corporate personalization PIN required Corporate personalization PUK required 27
51. t is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Max 5 characters Password of the device Only correct password can access the Parameters oo device and change the configuration The minimum length of Password E character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Report ID Specify the report identifier which will be cleared The effective identifier range is from 50 99 255 clear all report ID Ex Issue command WP CLEVT 0000 50 Response OK CLEVT 50 Example Sm Issue command WP CLEVT 0000 255 Response OK CLEVT 255 Copyright Wonde Proud Technology 2007 All rights are reserved 34 of 58 WONDE PROUD TECHNOLOGY SWP IMEI Execute this command to query the IMEI No for the internal GSM module S WP IMEI Tag Password OK IMEI Tag IMEI No S ERR IMEI Tag Error Code Error Response _ Please refer to appendix 9 2 for detailed error code descriptions The tag could consist of number or character string which can be defined by user The returning message will include the same tag and Tag it is helpful to recognize the acknowledgements with corresponding issued commands This tag could be left as empty if it is not used Parameters Max 5 characters Password of the device Only correct password can access the device
52. t message transfer rejected 21 Destination out of service 28 Unidentified subscriber 29 Facility rejected 30 Unknown subscriber 38 Network out of order 41 Temporary failure 42 Congestion 47 Resources unavailable unspecified 50 Requested facility not subscribed 69 Requested facility not implemented 81 Invalid short message transfer reference value 95 Invalid message unspecified 96 Invalid mandatory information 97 Message type non existent or not implemented 98 Message not compatible with short message protocol state 99 Information element non existent or not implemented 111 Protocol error unspecified 127 Interworking unspecified 128 Telematic interworking not supported 129 Short message Type 0 not supported 130 Cannot replace short message 143 Unspecified TP PID error 144 Data coding scheme alphabet not supported 145 Message class not supported 159 Unspecified TP DCS error 160 Command cannot be actioned 161 Command unsupported 175 Unspecified TP Command error Copyright Wonde Proud Technology 2007 All rights are reserved 53 of 58 WONDE PROUD TECHNOLOGY eee rE eee ES Error code Description TP DU not supported o 176 TP DU not supported e es O No SC subscription it erm s rases E Destination SME barred E om rw Er TP VP not supported ais gsmssesee O 8 ne st seen eN Error in MS at E 212 sm appicaton Totey OOOO SoSo O as smosso OOS as Unspectiosenorcause OOOO NSS Ia SMS service of ME rese
53. t will be transmitted Ack OK DCMSG Text GPRS server receives DCMSG unit ID Text DateTime 20 Remote Parking function Enable Disable WP PARK PWD Enable Disable Enable Disable Parking Button PWD PWD of the device Enable Disable 0 Disable 1 Enable Enable Disable Parking Button 0 Disable 1 Enable Note Once the unit is parking enabling then configuring WP PARK 0000 1 remotely will renew parking enabling Query Status WP PARK 0000 21 Mileage function WP SETMILE PWD Enable Disable Set Mileage PWD PWD of the device Enable Disable 0 Disable 1 Enable Set Mileage Value of intial mileage 22 Contact list function gt V1 006Rev49 S WP PHONEBOOK PWD Index Name Phone number PWD PWD of the device Index 1 15 255 to clear all list Name The text should be put in start quote and end quote quote symbol The maximum length is 16 chars numerical and characters Use to clear the content Phone number maximum length is 16 digits Supporting Use to clear the content Note 1 This page will be displayed after the dialing page 2 Every time you switch to this page the first contact information will be displayed 3 Show the first contact information on the LCD for ex first line the name second line the GSM number 4 The empty information will be displayed with empty page with Index number the empty page
54. terval only integer can be used Range 25 65535 meters Note For vehicle application suggest to set 50 meters or above for better performance Copyright Wonde Proud Technology 2007 All rights are reserved 20 of 58 WONDE PROUD TECHNOLOGY ns EE The position information is logged into the memory of the device according to the reduired Time interval AND Distance interval the position information is not logged if one of the Time interval and Distance interval does not satisfy 4 Time OR Distance The position information is sent to the base station when one of the following condition is satisfied a Time Interval is reached b Distance Interval is reached Heading mode The position information is sent when the Heading direction parameter is changed beyond the assigned degrees Please enter the required value in the Heading column Heading OR Time The position information is sent back to the base station when one of the following condition is satisfied a Heading direction parameter is changed beyond the assigned degrees b Required Time Interval is reached 7 Heading OR Distance The position information is sent whenever one of the following condition is satisfied a Heading direction parameter is changed beyond assigned degrees b Required Distance Interval is reached Heading OR Time AND Distance The position information is sent ba
55. umber can be used Effective range for different communication types Direct Connection 1 65535 seconds GSM SMS 15 65535 seconds GSM CSD 5 65535 seconds GPRS UDP TCP IP 5 65535 seconds bs ee N The position information is sent to the base station according to the required distance interval only whole number can be used Effective range for different communication types Direct Connection 25 65535 meters GSM SMS 300 65535 meters GSM CSD 100 65535 meters GPRS UDP TCP IP 100 65535 meters Copyright Wonde Proud Technology 2007 All rights are reserved 16 of 58 WONDE PROUD TECHNOLOGY aaa AN ee ee ee 3 Time AND Distance The position information is sent back to the base station when following BOTH conditions are satisfied a Time Interval is reached b Distance Interval is reached 4 Time OR Distance The position information is sent to the base station when one of the following condition is satisfied a Time Interval is reached b Distance Interval is reached Heading mode The position information is sent when the Heading direction parameter is changed beyond the assigned degrees Please enter the required value in the Heading column Heading OR Time The position information is sent back to the base station when one of the following condition is satisfied a Heading direction parameter is changed beyond the assigned degrees b Required Time Interva
56. unication 2 CSD Circuit Switched Data communication Reserved currently not support 3 GPRS UDP communication 4 GPRS TCP IP communication SMSBase Base phone number for the GSM SMS base station Maximum Phone length is 16 digits could be ignored if uses GPRS communication Copyright Wonde Proud Technology 2007 All rights are reserved 10 of 58 WONDE PROUD TECHNOLOGY CSDBase Base phone number for the GSM Circuit Switched Data Phone communication Maximum length is 16 digits could be ignored Reserved if uses GPRS communication GPRS_APN Access Point Name for GPRS service required for GPRS communication The maximum length is 40 characters GPRS_Username User name for GPRS service if applicable ME N GPRS Password Password for GPRS service if applicable N Er si eN Default setting 0 0 0 0 GPRS ServerlPAddr 1 Static IP address ess format xxx Xxx Xxx xxx Please do not use virtual IP address DNS name GPRS_DNS must be defined for the base station The maximum length is 40 characters GPRS ServerPort The port IP of the computer which the control center software is operating The available range is from 1000 65535 Default setting 1000 GPRS Synclnterval Sync message is used to establish the GPRS connection and maintain the GPRS connectivity between the device and the base station The range is between 10 65535 seconds Default setting 30 seconds Note Set to 0 to disable sendi
57. will not be skipped 5 Navigate into the contact list by the C3 C2 button up down 6 Select the contact by P button and hold this key for 3 seconds to make dialing process 7 The reset function will not erase the phone book information 23 Pre defined message function gt V1 006Rev49 WP MSGBOOK PWD Index Text PWD PWD of the device Index 1 20 255 to clear all list Text The text should be put in start quote and end quote quote symbol The maximum length is 16 chars numerical and characters Use to clear the content Note 1 This page will be displayed after the Phone book page 2 Every time you switch to this page the first message will be displayed 3 Show the first message on the LCD 4 The empty information will be displayed with empty page with Index number the empty page will not be skipped 5 Navigate into the message by the C3 C2 button up down 6 Select the contact by P button and hold this key for 3 seconds to send the message back to control center 7 The Reset function will not erase the message list 24 Change the no phone message and emergency SMS message by an owner msg 2 V1 006Rev49 WP STDMSG PWD C button Msg SOS Msg PWD PWD of the device C Button Msg The text should be put in start quote and end quote quote symbol The maximum length is 16 bytes SOS Msg The text should be put in start quote and end quote quote symbol The maxi
58. word of the device Only correct password can access the device ese and change the configuration The minimum length of character is 4 digits maximum length of character is 10 digits It supports numerical characters only Default password is 0000 Parameters 0 Disable Mode 1 GPS off GSM on GPRS on LCD on 2 GPS off GSM on GPRS off LCD off Power Down 60 65535 seconds Delay 0 Device will not go to sleeping mode while the WP TRACK and Sleeping WP SPD command are executing Priority 1 Device goes to sleeping mode regardless the execution of WP TRACK and WP SPD command Ex Issue command Example WP PSM 0000 1 120 1 Response OK PSM 1 120 1 Copyright Wonde Proud Technology 2007 All rights are reserved 290f 58 WONDE PROUD TECHNOLOGY 1 Conditions for entering sleep mode AND algorithm 1 No movement within Power Down Delay duration mode 1 and mode 2 2 Not receive any command within Power Down Delay seconds mode and mode 2 3 No button is pressed within Power Down Delay seconds mode 1 and mode 2 4 No undelivered messages exist mode 1 and mode 2 5 No WP TRACK or WP SPD command is used mode 1 and mode 2 2 Condition for device waking up OR algorithm 1 Movement detected Mode and Mode 2 2 Any button is pressed mode and Mode 2 3 Receive GSM or GPRS command mode 1 4 Receive GSM command mode 2 3 If device wakes up and compl
59. yright Wonde Proud Technology 2007 All rights are reserved 5 of 58 WONDE PROUD TECHNOLOGY eee eae Entering a Series of WP commands on Separate Lines In order to successfully enter series commands through separate lines a pause is suggested to add between each command preceding and following commands until the final responses appears such as OK lt Command gt This action will avoid sending too many WP commands at the same time but without receiving the responses for each issuing command to ensure the device receives all command correctly and successfully Default parameters for each command are underlined in this document for reference There are two types of data transmission formats Binary format For Synchronization message ASCII format for all data transmission except the Synchronization message 5 Supported Communication Types The SPT100 device supports GSM frequency of 850MHz 900MHz 1800MHz and 1900MHz The device could be communicated with the base station via several communication ways such as following Direct connection via RS232 communication port Auto adjustable baud rate GSM SMS messages Peer to peer and TCP IP network GSM CS Data GSM Circuited Switch Data Reserved GPRS UDP Static IP address is required for controller center software GPRS TCP IP Static IP address is required for controller center Please note SPT100 currently does not support CDMA communication
Download Pdf Manuals
Related Search