User Manual (English)
Contents
1. 0 40 Red 0 45 Blue 5 56 223 Black 7 62 308 White Size of ball bearings per caliber Caliber Ball diameter 9 38 4 5mm 0 40 4 0mm 1 Threaded dropper body 2 Inner dropper tube 0 45 3 5mm 3 Lower brass adaptor 4 Perspex tube 5 Switch section 5 56 223 6 0mm 7 62 308 5 0mm The dropper also includes 3 steel ball bearings A retention spring A micro switch attached by cable tie MOUNT ASSEMBLY The mount assembly is shipped disassembled and you have to assemble it first Included in the kit are the screws needed as well as a 4 mm hex key You will also need a medium sized Phillips head screwdriver Horizontal mount rods Short vertical mount rod Long vertical mount rod Lower pucks Upper pucks ORWNR INSTALLING AND ADJUSTING THE POWDER FUNNEL Your Mr Bulletfeeder is supplied with a newly designed and improved powder funnel The powder funnel is a very important component of a bullet feeder of any kind as it prepares the brass correctly so that the bullet can be seated in the case and not tip over as you index the shell plate To achieve this we have redesigned the powder funnel to allow for just the right amount of expansion without over flaring or stressing your brass It is recommended that you adjust your powder funnel first before assembling the dropper as you will need properly prepared brass when adjusting the dropper Note that our droppers are somewhat shorter than the standa2. 8 mm and the bullet is now entering to the correct depth The second critical adjustment in the nose guide is to position it correctly so that the right amount of ledge shows inside the pocket This ledge allows bullets which are base down to ride over it and not fall into the groove in the nose guide while al lowing bullets which are nose down to fall in and be rotated The amount of ledge you want really depends on the caliber and profile of the bullets you are loading and should be adjusted as needed The left image shows the nose guide positioned too low too inwards and so no ledge is showing All the bullets regardless of their orientation will drop into the slot and be turned The middle image shows the correct amount of ledge showing in the pocket With this correct setting the bullets which are base down will ride past the slot and not be rotated while the bullets which are nose down will fall in and rotate to the correct orientation The image on the right shows the nose guide set too far out too much ledge showing and so no bullets will fall in and none will be rotated To adjust the nose guide loosen the screw from below the collator base and slide the nose guide inwards or outwards as needed Then tighten it up You will need a Phillips head screwdriver When you find the perfect position for a particular bullet type make note of the nose guide position and the number of spacers in use so the next time you can adjust d
3. change your brass you may find you need to adjust both the powder funnel and the height of the dropper for best results Now assemble the top part of the dropper back into place and tighten the lockup screw in the brass section Make sure that the dropper assembly is not rubbing up against any section of the powder measure In some machines these can be positioned very close together You may need to slightly rotate the powder measure a little and or rotate the retention spring in the drop per assembly It is important that the dropper moves freely up and down without any interference Dismantling the Dropper Body Should you need to dismantle the dropper body do so above a bowl as the small steel ball bearings in side fall out and are easily lost Take care not to bend the micro switch arm out of shape It must be free to move in and out of the slot First remove the top section by unscrewing the lockup screw in the brass section Remove the top section and set it aside This part cannot be dismantled and should not need to be You can clean it by running through a cloth or a bore rope type cleaner To dismantle the lower section first remove the reten tion spring Then the inner tube can slide down and out of the threaded die body As you push it down the three steel ball bearings will fall out be sure you are over a bowl to catch them Three extra steel ball bearings are included as spares You should not need to disma
4. into the holes in the rods first just to clear any burrs which may make it difficult to assemble 11 12 3 Once the horizontal bars are in place assemble the lower pucks to them and then the vertical rods The design of this mount system using all round profile parts allows for an almost unlimited range of adjustments This will allow you to posi tion the bullet collator just right 4 Set the angle The collator is designed to function at a 45 degree angle Small adjustments can be made from there as some bullets may collate better at a steeper or flatter angle However the starting point should always be 45 degrees A good method to set this angle is as follows Push the front vertical rod all the way up through the upper puck until both pucks on that front rod are touching On the back vertical allow a gap of 6 5cm 2 5 2 6 inches between the inner edges of those two pucks Tighten the screws only lightly just to hold the rods from sliding These puck positions will set the collator base at about 45 degrees when you hang it on the horizontal rim of your case feeder 5 Hang the bullet feeder on the rim of the case feeder rotating the hanger parts into shape as you position it Note that you will most likely need to push the bottom horizontal rod through the lower puck about half an inch so that it can make contact with the sloping side wall of the case feeder This is important to sta bilize the bullet collator and keep it leve
5. The flexibility of this design means that you can position your bullet feeder collator anywhere around the case feeder that best suits your need The symmetrical design of the new mount system enables you to mount the bullet feeder collator so that the case feeder is on its left or its right When mounting to a 1050 the case feeder will be to the left of the bullet feeder and when mounting on a 650 to the right The horizontal mount rods can be assembled protruding either left or right as needed The bullet feeder on the left is being prepared to mount to a 1050 with the case feeder to the right of the bullet feeder The right image shows the setup for a 650 on which the bullet feeder is mounted with the case feeder to its left Follow these steps to assemble the mount 1 Screw all the M8 screws into the threaded holes in the Delrin pucks Two screws in each for a total of eight Take care to align the screws correctly and do not force them so as not to damage the threads 2 First determine whether you are going to assemble the unit to the left or to the right of the bullet feeder and attach the horizontal rods accordingly These horizontal rods have a pair of M4 threaded holes through them which line up with the cor responding holes in the bottom of the collator base plate Use the four M4 screws supplied To access the screws you first need to remove the collator plate from the collator Note that it is better to try and run the screws
6. You will need a Phillips head screwdriver ASSEMBLING THE OUTPUT TUBE AND LEAD SPRING ASSEMBLY Now that your collator and dropper are well adjusted it is time to connect the two and see the system work Your bullet feeder includes a lead spring assembly which at one end has the collator output tube and at the other the spring adaptor cap which fits on top of the dropper First attach the collator output tube to the large hole positioned at about 2 o clock in the base of the collator Push it firmly in until it stops against the shoulder machined in the part Rotate the output tube so that its debris slot is on the downward side thus allowing debris to fall through if necessary Tighten the M4 screw lightly to hold it in place Do not over tighten The spring adaptor cap fits on top of the switch section in the dropper assembly with its flat side facing the switch There is a set screw in the side of the part screw that in to hold it in place The screw will enter into a groove in the switch section Again do not over tighten The output tube is positioned so that the debris slot is on the downward side allowing debris to fall out 17 Note the position of the spring s adaptor cap as it attaches to the top of the dropper assembly Its flat side fits snugly around the micro switch Note the two wires at tached to the outer ter minals of the switch Adjusting the Spring Length The spring is supplied long enough to s
7. a slightly slower speed and you can run the col lator on 9v or less as well CAUTION Should the collator stall for any reason be sure to turn the pow er off before trying to clear it It can be dangerous if it suddenly starts turn ing while your fingers are close to the collator plate The plate turns with considerable force Connect the end terminals of the retractable cable to the two terminals of the micro switch as shown The middle terminal is bent down and is not used There is no polarity to be concerned with 19 Double Alpha Academy B V Elzenweg 33b 5144MB Waalwijk Netherlands Tel 31 416 660 464 fax 31 416 392 040 Email 2sc doublealpha biz wwWw daublealpnha blz www Mc Bulletfeeder by Double Alpha
8. irectly to this setting Adjusting the Flip Ramp Once a nose down bullet has dropped into the slot in the nose guide the rotating plate continues to move it clockwise and it begins to rotate past the vertical position in the nose guide before reaching and riding up the flip ramp to complete the 180 degree flip inside the collator plate pocket 15 16 Make sure that it is up close to the collator plate if you are feeding short bullets such as 9 mm Adjust it further away for long rifle bullets If the ramp is set too far out and the tip of the bullet does not ride up it it may slip underneath causing the collator to jam If it is too close and a long bullet is used it may lift the entire bullet up and out of the pocket rather than rotating it in the pocket The ramp can be adjusted to move its tip closer to or further away from the spinning collator plate You should adjust it ac cording to the length of the bullets you are using The left image shows the correct ramp position for these 9 mm bullets the ramp is close up against the collator plate and so the bullets can ride up the ramp and complete their rotation In the right image the ramp is positioned much too far out for these bullets and the bullet tip is missing the ramp and jamming up beneath it To adjust the flip ramp loosen the screw from below the collator base and rotate the flip ramp s tip closer to or further from the collator plate as needed Then tighten it up
9. it is rejected and has to be inserted again These systems are always rather slow on feeding bullets and in some cases very slow Not so Mr Bulletfeeder by Double Alpha Mr Bulletfeeder s patented system has the ability to allow the bullets that are the right way up to pass on down the tube and those that are nose down to be flipped in their pockets so not wasting any time feeding them down the tube base down This is achieved by the nose guide and flip ramp 13 14 Adjusting the Nose Guide The first thing to consider with the nose guide is how many of the thin laser cut insert plates to use The unit is supplied with four two each 0 8 mm and 1 6 mm thick You can add and remove these as needed depending on the type and length of bullet you are loading Add or remove these insert plates so that when the head of the bullet falls down into the slot and rests on top of the insert plates the base of the bullet is not raised above the upper edge of the collator plate In fact it should be slightly below the top edge at all times If the bullet drops too low use an additional spacer plate You may need to experiment a little for best performance In the left image not enough spacers are used in the nose guide for this 124 gr 9 mm bullet and consequently the bullet s base is dropping too low below the level of the top of the collator plate In the right image extra spacers have been added into the nose guide 2 x 1 6 mm and 1 x 0
10. justing the 8 Assembling and Adjusting the Collator Mounting System 10 Adjusting the Nose Guide and Flip 13 Assembling the Output Tube and Lead Spring Assembly 17 Witlmgy 19 WHAT S IN THE BOX AND EXPLODED VIEW ASSEMBLIES Inside the box you will find Collator Assembly Dropper Assembly Powder Funnel for pistol calibers only Power Supply Mount Assembly dismantled Lead Spring Assembly Instruction Manual COLLATOR ASSEMBLY First remove the tape securing the collator plate in place and then turn the collator upside down to remove the collator plate You may need to shake it a little Once removed you can also remove the tape securing the spacers inside the nose guide Take care you do not lose these as they can fall out Collator base Motor and gear assembly Output tube Collator side wall Collator plate Flip ramp Dislodge arm Nose guide Nose guide spacers DROPPER ASSEMBLY Inside the square telescopic packaging tube you will find the dropper assembly the powder funnel and a set of spare stainless steel balls for the dropper as per your caliber Color identification for dropper assemblies Caliber Switch cable tie color 9 38 Yellow
11. l Once all is in position carefully remove the bullet feeder and tighten up all the screws in the mount assembly This image shows a good starting point for the angle adjust ment which will set the collator plate at the required 45 degree angle Note that the short vertical arm is set to zero distance between the pucks and the rear one has a gap of about 6 5cm 2 5 between the pucks 6 Hang the collator back on the rim of your case feeder Con nect the output tube and spring to the top of your dropper and make sure the collator is in the best possible position allow ing the most direct line for the bullets to feed down the output spring Make sure the spring is not pulling on the dropper Once you are satisfied with the bullet collator s position tighten the screws on the inside of the upper pucks to lock the bullet colla tor in place Especially when mounting to a 650 you will want the lower hori zontal rod to protrude through the lower puck as shown with the red arrow to rest up and support the collator s weight keeping it level and preventing it from sagging outwards The angled side wall of the case feeder makes this necessary ADJUSTING THE NOSE GUIDE AND FLIP RAMP The nose guide and flip ramp of the collator are the business end of the system and they are what make the collator work so efficiently Other bullet feeders utilize a rejection type system when a bullet enters a pocket the wrong way up
12. ntle the dropper often The picture above shows the dismantled dropper lower section Once the clip is removed the inner tube can be slid out down wards Note the three small ball bearings which are caliber spe cific Always dismantle over a bowl as the small balls will drop out when you remove the inner tube from the threaded body 10 In the inner tube you will notice two rows of three holes The lower level is normally only used for very short bullets perhaps 90 gr 9 mmor very short 40s It is better to use the upper row of holes as it will allow the column of bullets to drop a little further thereby better tapping the lower bullet into place Rifle caliber tubes may have three rows of holes To reassemble slide the inner tube into the threaded body from below until the row of holes is just visible Position the three steel balls on the same level of holes each separated by 120 degrees and slide it further up until the threaded body retains the balls Then slip the retention spring back into place Use the upper groove when using the upper row of steel ball pockets normal setup and the lower groove when the steel balls are positioned lower for very short bullets ASSEMBLING AND ADJUSTING THE COLLATOR MOUNTING SYSTEM The new Mr Bulletfeeder by Double Alpha is designed to be attached to the outer rim of your case feeder This improvement makes the unit lighter and more compact and takes no space at all on your reloading bench
13. rd ones provided by Dillon so you will most likely need to adjust your powder measure die down It is best to do this with an empty powder measure Place a resized brass under the powder measure and cycle the handle of the machine down Adjust the die of the powder measure down in small steps until it makes full contact with the brass and is operated fully charge bar slides forward and backward Note how far the powder funnel tip enters into the brass before it is released You should aim to adjust the funnel down until the top edge of the case just starts to push up onto the tapered section of the powder funnel achieving a minimum amount of rim flare In this position the lower section of the powder funnel has entered into the case expanding the top just a few millimeters enough to allow the bullet to sit correctly in the case and not tip over as the machine indexes A good test is manually to place a bullet into a case you have cycled through the powder station With a well adjusted powder funnel the bullet should be seated smoothly a couple of mm into the case and should not fall out easily even when you turn it upside down The picture on the left shows a powder funnel not adjusted far enough down The funnel enters into the case but does not go down far enough The bullet may not be seated deeply enough and may tip over as you index the machine The center image shows a correctly adjusted funnel the case enters up far enough to jus
14. supporting loop midway down the spring perhaps attached to the case feeder which prevents the bend from being too pronounced in the spring WIRING UP The power supply provided with your unit is dual voltage and includes a choice of two mains cables one for the US market 110v and one for Europe 220v Select and attach the correct one for your region The 12v DC cable is long enough to allow you to position the power supply in an accessible position on your reloading bench Plug that connector snugly into the female jack protruding from the side of the collator base The micro switch on the dropper serves to stop the collator from turning and feeding bullets when the dropper tube is full Since the bullet feeder can collate bullets much faster than you can use them it is necessary to have this cut off switch to prevent the bullets filling up the lead spring all the way to the collator and jamming it Attach the two terminals at the end of the retractable cord to the two outside ter minals of the micro switch and push firmly into place The middle terminal on the switch is not used and is bent down to avoid confusion There is no polarity to be concerned with either wire can be attached to either terminal Your unit is now ready to run The power supply provides an adjustable potentiometer switch which allows you to supply the default full 12v power that will provide maximum speed You may find that some bullets collate better at
15. t reach the chamfered area of the funnel and receive a slight belling The image on the right shows a funnel set too deep The case is excessively belled and will fatigue quickly it may not hold the bullet straight The resulting bullet seating of the three powder funnel heights The left bullet is not seated well as the funnel is too high and as a result the bullet is likely to tip over as you index the machine The middle bullet is well tapped into place and will remain straight and true as you index The right bullet shows the result of belling the case too much The deformation in the case will cause rapid case fatigue and the bullet may not remain straight as you seat it INSTALLING AND ADJUSTING THE DROPPER For ease of handling you can remove the top section of the dropper and use only the lower aluminum assembly To do this open the small lock screw in the lower brass section of the dropper and gently remove the upper part of the assembly from the brass section up and set it aside Since the dropper is generally installed in the station following the powder measure place a properly prepared case in the shell plate below that station and cycle the press handle all the way down Note If you are using a powder check in the station following the powder measure you will need to install the bullet dropper in the next station On a 650 this means you will need to use a combined seating and crimp die in the final station Slowl
16. uit the most extreme case we have found that of the old 650XL with the case feeder set off to the left of the machine In that setup the spring needs to be full length With the newer 650 or 1050 you may find that you can cut a little off from the spring to get better performance You need the spring to reach down to the dropper without pulling on it at all as that tension can cause the dropper to snag However you don t want the spring to be too long that can cause a bend in the spring which could trap bullets midway down causing them not to slide down as they should Find the best position for your collator which allows the straight est possible route down towards the top of the dropper so the bullets can slide easily Special note regarding 1050 setup Here the length of the spring is even more critical Since the tool head dropper assembly is moving up and down as you reload the spring should not be cut too short You do not want the spring to pull up on the dropper as you lower the tool head Therefore when you position the collator unit and adjust the spring check the length with the tool head all the way down Make sure the spring is long enough not to pull on the dropper You may then find that when you bring the tool head up a bend is created in the spring but if the collator is well positioned this should not become a bullet trap Check this as you set up You can also make a fur ther improvement by improvising a
17. www mrbulletfeeder com www doublealpha biz US Patent 7497155 and US Patents P MR BULLETFEEDER BY DOUBLE ALPHA USER MANUAL US PATENT 74975155 AND US PATENTS PENDING Thank you for choosing Mr Bulletfeeder by Double Alpha This newly designed product will give you years of reliable service It will make your reloading sessions easier and faster than ever before It is critically important that you set up your bullet feeder correctly so PLEASE take the time to read through this instruction manual before starting to assemble and use your bullet feeder You will save considerable time and effort by reading these instructions first For further information please visit our website www mrbulletfeeder com There you can view detailed video tutorials on how to set up and use your bullet feeder If you have any questions email us at osc doublealpha biz WARNING Reloading ammunition is inherently hazardous BE SAFETY CONSCIOUS AT ALL TIMES and ALWAYS USE EYE and EAR PROTECTION Maintain a sturdy clean organized reloading bench CONTACT INFORMATION Double Alpha Academy B V Elzenweg 33b 5144MB Waalwijk Netherlands Tel 31 416 660 464 fax 31 416 392 040 Email osc doublealpha biz www doublealpha biz www mrbulletfeeder com INDEX What s In the Box and Exploded View of 1 Assembling and Adjusting the Powder 5 Assembling and Ad
18. y screw the dropper s threaded body into the tool head for 2 or 3 turns and then fill the dropper tube with bullets all base down You can fit 5 or 6 bullets into that section Continue to screw the threaded body down until you see that the inner section stops moving down it has made contact with the rim of the case beneath it Very slowly continue to screw the threaded body down until you hear and see the column of bullets inside the tube drop down Turn the threaded body another quarter turn and tighten the nut by hand This is the cor rect height position Raise the tool head You should see one bullet sitting firmly in the case Note that the dropper does not seat the bullet to length and only lightly taps the bullet in so that it does not fall when the machine is indexed Do not over tighten the locking nut It is not necessary and you may damage the threaded body which is made of aluminum Tighten by hand or lightly using a spanner wrench There is no force applied to the dropper body during function so there is no risk of it moving If desired a drop or two of low strength Loctite may be applied Do a final check by cycling the press a few times Use your prepared case and 5 or 6 bullets in the tube for each cycle Confirm that each time one bullet is dropped and tapped into place on the case Your dropper is now correctly adjusted Note that different brass may have slightly different lengths even within the same caliber Should you
Download Pdf Manuals
Related Search