TomTom GPS Systems User Manual
Contents
1. find in your WEBFLEET contract confirmation Download the latest version of the Activation Tool from the Reseller section on http business tomtom com under Software download Installing your ecoPLUS There are two steps to setting up your ecoPLUS 1 Configuring a Bluetooth connection between your ecoPLUS and your LINK 300 310 There are two ways to establish a Bluetooth conection between your ecoPLUS and your LINK UsingWEBFLE ET s e e Configuring a Bluetooth connection with WEBFLEET UsingtheActivationTlool s e e Configuring a Bluetooth connection with the Activation Tool Make sure you have properly noted and entered the Bluetooth address of your ecoPLUS which you can find on the label on the OBD II plug 2 Installing your ecoPLUS in your vehicle Follow the instructions in Installing ecoPLUS in your vehicle to install the ecoPLUS in your vehicle Configuring a Bluetooth connection with WEBFLEET This section describes how to pair your ecoPLUS with the LINK 300 310 installed in your vehicle using WEBFLEET If you want to use the Activation tool instead see instructions under Configuring a Bluetooth connection with the Activation Tool Note Make sure your vehicle is properly fitted with a LINK 300 310 as described in Requirements URL http business tomtom com login O By ees torner F Papini i Be Eat EA Feedback J Serre Begire 1 01 00 Erd Tarii WENT Acima code SEDER See Hee namn dubio2. TomTom ecoPLUS Installation Guide Welcome Before the installation With the TomTom ecoPLUS you can retrieve fuel consumption data over your vehicle s OBD II connector and see this in TomTom WEBFLEET in real time TomTom ecoPLUS works together with the TomTom LINK 300 310 via Bluetooth and therefore requires minimal installation effort This document shows how to set up your ecoPLUS If you need to use your vehicle s OBD II connector for something else for example for maintenance purposes simply remove your TomTom ecoPLUS from the connector and reconnect it afterwards Components The following figure shows you the different parts of your ecoPLUS Requirements A Power LED Bluetooth LED CO Reset button D Data cable E Bluetooth address OBD II plug 0 O 98 Before installing your ecoPLUS make sure you fulfil the following requirements Your vehicle is fitted with either a TomTom LINK 300 that has a serial number that starts with LA ora TomTom LINK 310 The LINK 300 310 must be activated in TomTom WEBFLEET The LINK 300 310 must have the firmware version 1 8501 or higher Download the latest firmware version from the Reseller setion on http business tomtom com under Software download Your vehicle has an OBD II connector To use the activation tool for your LINK 300 310 you need a laptop with the activation tool installed a serial cable and the activation code which you can
3. US can be calibrated amp Alex F work T 4h 58min amp Vehicle available no further orders for today gt Af Igntiion on 2665 km Business E ecoPLUS calibration in progress 55 ar SS Se U M _ Position v T ccc _ 15 42 67 km h 8 0 km south west Markaryd SE E4 near j frack Ga Trips Alex F O Work F 4h S8min Vehicle available no Further orders For today L A Ignition on 2665 km Business E 12 6 1 100 km 1 61 3100 rpm Gear 6 Jun a ES V CCS frack Ga Trips Diagnostics Understading your ecoPLUS In the following table the different LED modes are explained showing you working stages of your TomTom ecoPLUS _ X AA GTG O4 H RHHRH H Mn nB h j gt wtb Ht aS S SsSSYS gt j Fully operational Green LED Is on ecoPLUS has power and is on Blue LED is on The devices are identified to each other and a Bluetooth connection is established Establishing a connection Green LED is on ecoPLUS has power and is on Blue LED is flashing The devices are identified to each other and are trying to establish a Bluetooth connection Factory default devices not identified Green LED Is on ecoPLUS has power and is on Blue LED is off Devices are not identified to each other and have no Bluetooth connection Power save mode Green LED ts flashing and blue LED Is of
4. f ecoPLUS is in standby mode and has no Bluetooth connection No power Green and blue LED are off ecoPLUS has no power is not connected Resetting your ecoPLUS If you encounter errors with your ecoPLUS or your ecoPLUS is not working as expected you possibly need to reset the device To reset your ecoPLUS press the reset button for five seconds while it s connected to the OBD II connector and supplied with power Technical data IP33 Protection class Operating voltage 8V to 30V Temperature Operation 30 C to 70 C GPS SYSTEMS TOMTOM GPS
5. s Telerutics dev n LINE TP Serial miber LASS Software Aeee 6501 1 Log in to WEBFLEET here http business tomtom com login 2 Click Vehicles 3 Select your vehicle from the list 4 In the details panel on the right click Contract Device 5 Click Configure 6 Select the Accessory tab g 009 Your vehicle Fi Basic settings Status messages Order messages Input p ap Bluetooth configuration _ Connect navigation system onty Bluetooth acessories cannot be connected wh the configuration Connect Bluetooth accesso case a navigation system needs to be connected with thes configuration at least sofheare CEEE needs to be reset once Remote LINK Bluetooth remote control Bluetooth address e g On SAIF Az Oo 7 Under Bluetooth configuration check the radio button for Connect Bluetooth accessory to be set 8 Inthe TomTom ecoPLUS section enter the engine size of your vehicle in cc Make sure you have entered the correct engine size as this is the basis for the calculation of your vehicle s fuel consumption 9 Enter the Bluetooth address indicated on the OBD II connector of the ecoPLUS you want to install in that specific vehicle S N LM1234000000 10 Click Save The Bluetooth address of your ecoPLUS is now assigned to the LINK 300 310 in the vehicle you selected Now you should connect your ecoPLUS For more information see Installing ecoPLUS in your vehicle Configuring a Blue
6. stalling ecoPLUS in your vehicle This section describes how to connect your ecoPLUS to the vehicle and to the LINK 300 310 1 Find the OBD II connector in your vehicle You can find the OBD II connector in the driver s footwell area If you are not sure where to find it see your vehicle s service manual or contact you car dealer 2 Insert the OBD II plug of your ecoPLUS into the OBD II connector of your vehicle Make sure the plug is fully inserted so it cannot drop off SO The green Power LED goes on 3 Optionally you can slide off the ecoPLUS from the plug to place it aside if the available space does not allow for an assembled installation es in Important Affix the loose ecoPLUS so that it cannot drop off and fall into the footwell area or get damaged Make sure the Power and the Bluetooth LED stay visible for diagnostics purposes 4 Turn on the ignition The LINK 300 310 tries now to establish a connection to your ecoPLUS This may take up to two minutes If successful both LEDs should be solid You have now completed the installation of the ecoPLUS and successfully established a Bluetooth connection between your ecoPLUS and the LINK 300 310 The ecoPLUS automatically learns from the vehicle and the engine during operation Therefore the vehicle needs to be moved around for some time so the ecoPL
7. tooth connection with the Activation Tool This section describes how to pair your ecoPLUS with your LINK 300 310 using the Activation Tool If you want to use WEBFLEET instead see instructions under Configuring a Bluetooth connection with WEBFLEET 1 Install the latest version of the Activation Tool to your Microsoft Windows running PC 2 Use the serial cable from the LINK 300 310 Service Set to connect your LINK 300 310 to your computer 3 To start the Activation Tool double click the icon 4 Select from the pull down menu the COM port to which you have connected your LINK 300 310 Make sure the green LED on the LINK 300 310 is solid on before you continue with the next step 5 Click Ok 6 Select the ecoPLUS tab 7 Enter in the engine size of your vehicle in cc 8 Enter the Bluetooth address indicated on the OBD II connector of the ecoPLUS you want to install in that specific vehicle FKMO0 001 00 Made in TH TOMT Contains FCC ID Pl4411B S N LM1234000000 9 Click Save You are prompted to enter the activation code for the LINK 300 310 10 Enter the activation code You can find the activation code in your WEBFLEET contract confirmation Tomtom LINE Activation Tool 1 9 11 Click Ok After a few seconds the Bluetooth address also appears in the right text field Tomtom LINE Activation Tool 1 9 12 Carry out the steps described above for each additonal ecoPLUS and LINK 300 310 In
Download Pdf Manuals
Related Search