User Manual For Zamst A2 DX Ankle Brace
Contents
1. ZAMST A2 DX ANKLE SUPPORT INSTRUCTIONS FOR USE Please read through the following instructions completely before using the product Intended use Ankle protection Restriction of ankle inversion and eversion Anterior ankle stability This product is not for medical treatment This product is for ankle support however it will not prevent all ankle injuries Do not use this product in the following cases If you have abnormal conditions such as cuts fractures numbness swelling or rash in the area where product is used Safety precautions Ifyou experience pain swelling skin irritation discomfort or any other abnormal reaction while using this product discontinue use and consult with a physician If your skin is sensitive or you have allergies you may develop a rash or allergic reactions while using the product If such symptoms occur discontinue use and consult with a physician Do not use the product while sleeping If the product shifts to an abnormal position or is used for extended periods while sleeping it may interfere with blood circulation If the body part is compressed for extended periods blood circulation may be adversely affected or you may experience discomfort To avoid such conditions it is recommended that you remove and re apply the product at regular intervals If you play sports where the product s plastic components such as rigid guards could cause harm to other people do not use the product I2. f the product is broken or worn or if the hook and loop fastener does not work do not use the product Make sure to use the correct size and apply the support to the correct foot left or right Refer to the size chart on the package and size tag inside the product Do not pull the straps too tight or create excessive compression with the support If the product shifts out of place or becomes too loose re apply the product starting with the first step described in the How to apply instructions Do not modify or repair the product The product may lose its effectiveness and or cause injuries Wear the product over a sock Wearing the product in direct contact with skin may cause skin discomfort To prevent product damage The product may become discolored by perspiration or other liquids The product s dye may bleed onto clothing worn under or near the product Make sure that the hook and loop fasteners do not touch fabric They may damage fabric How to apply Illustrations are for the right ankle 1 Release and loosen all hook and loop fasteners Lay the rigid guards flat behind the ankle Hold the ankle in a vertical position Slide foot into the support from the back until the inner ankle bone is aligned with the area indicated by the dotted circle which is right above the rivet on the rigid guard Illustration 1 a Make sure that the center line of the foot is positioned just under the support s center line seam Illust
3. ration 1 b Pull hook fasteners A and B upward at opposite angles Fasten hook A Illustration 2 Wrap the support tightly around the ankle by pulling B hook fastener and C so as not to loosen the support Fasten B Illustration 3 Pull the crossing straps at opposing angles Fasten their edges above the ankle bone on opposite sides of the ankle Illustration 4 Stand the rigid guards upright Position them so that the raised area on the guard just above the rivet comes over the bone of the ankle which is indicated by the dotted area D by adjusting the length of the rear portion of the upper strap Fasten the hooks located on the inner side of each rigid guard to stabilize the guards Illustrations 5 a and 5 b 6 Use one hand to prevent the rigid guards from moving Wrap the upper strap around the leg and pass the strap through the plastic loop E Illustration 6 a Fold the strap back over itself Fasten hook Illustration 6 b 7 Product properly fastened Illustration 7 a Front view b Medial view c Back view 8 Inserting buffers F Illustration 8 The A2 DX is sold with two buffer accessories If you experience discomfort caused by the rigid materials use the buffers Examples a For top part of the rigid guard b For ankle bone area c For inside rivet area How to wash Hand wash with mild detergent and air dry Do not place in dryer Do not dry clean or iron Do not use products containing chlorine incl
4. uding bleach These may damage the product The product s dye may bleed Do not wash with whites or bright colors Composition Nylon styrene polyester polyurethane polyethylene rigid guards and brass rivet A2 DX indd 1 2 22 06 09 10 53
Download Pdf Manuals
Related Search