TUBE OVERDRIVE - HARMAN Professional
Contents
1. HARDWIRE 1157 7 TUBE OVERDRIVE e OWNER S MANUAL Digiech bv HARMAN DECLARATION OF CONFORMITY Manufacturers Name Harman Signal Processing Manufacturer s Address 8760 S Sandy Parkway Sandy Utah 84070 USA declares that the product Product name CM 2 Product option All requires Class power adapter that conforms to the requirements of EN60065 EN60742 equivalent conforms to the following Product Specifications Safety IEC 60065 01 Amd EMC EN 55022 2006 EN 55024 1998 FCC Part 15 Supplementary Information The product herewith complies with the requirements of the Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC RoHS Directive 2002 95 EC WEEE Directive 2002 96 EC EC Regulation 278 2009 With regard to Directive 2005 32 EC and EC Regulation 1275 2008 of 17 December 2008 this product is designed produced and classified as Professional Audio Equipment and thus is exempt from this Directive With regard to the PS200R and Directive 2005 32 EC and EC Regulation 278 2009 of 6 April 2009 this regulation applies to Class A single output external power supplies The PS200R used with this product is a multi output power supply and thus is exempt from this Directive Roger Johnsen Vice President of Engineering 8760 S Sandy Parkway Sandy Utah 84070 USA Date October 4 2010 European Contact Your local DigiTech Sales and Service Office or Harman Signal P2. Lock over the pedal knobs do the following I Set the knobs to your preferred setting 2 Gently push the StompLock over the top of the knobs 3 remove the StompLock gently lift one side and then the other Specifications Controls Jacks Input Impedance Output Impedance Input Impedance Output Impedance Power Supply Current Draw Power Consumption Dimensions Weight Optional Power Supply Power Supply Polarity Power Supply Output Level Low High Gain Voice Switch On Off Pedal Input Output 7500 kQ effect on kQ effect on True hardwire bypass effect off True hardwire bypass effect off 9V Alkaline Dry Battery or Harman power supply 25 mA typical at 9 VDC 220 mW typical w optional power supply 525 L x 3 5 W x 2 15 1 3 Ibs Country Voltage Japan 100 VAC 50 60 Hz US and Canada 120 VAC 60 Hz Europe 230 VAC 50 Hz UK 240 VAC 50 Hz Australia 240 VAC 50 Hz 6 6 o Compatible PSU Models PS200R 100 or PS09 3DC 01 PS200R 120 or PS0913DC 01 PS200R 230 or PS0913DC 01 PS200R 240 or PS0913DC 02 PS200R 240 AU or PS0913DC 02 PS200R 9 6 VDC 300 mA P509 13DC 9 VDC 1 3 Recommended power saving GreenEdge power supply models SEE Digitech by HARMAN 8760 South Sandy Parkway Sandy Utah 84070 PH 801 566 8800 FAX 801 566 7005 DigiTech and HardWire are registered trademarks of Harman Designed in the U
3. SA Copyright Harman Printed in China HardWire CM 2 Owners Manual 5024334 B Please visit our website at GreenEdge www digitech com by HARMAN
4. battery compartment Make sure the battery cable does not interfere with the spring or pedal switch arm Place one hole of the Foot Switch over its corresponding pin Push the opposite pin in and lower the other side of the Foot Switch into place over the depressed pin Release the pin When the Foot Switch is properly fastened both Release Pins are flush with the outer side of Foot Switch m the pedal SS Pedal Switch 3x 7 Arm A 9VDC Battery Foot Switch Release Pin Foot Switch Release Pin Pedal Chassis Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap The following accessories are included e Hook and loop Pedalboard Pad designed to attach to the surfaces found on most commercial pedal boards e Foot Switch Glow Sticker easily visible on dark stages StompLock keeps your settings where you want them Hook and loop Pedalboard Pad To attach the Pedalboard Pad do the following Peel off the existing rubber skid pad from the bottom of the pedal 2 Peel the adhesive protector from the back of the Pedalboard Pad 3 Apply the Pedalboard Pad to the bottom of the pedal Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker do the following Peel the adhesive backing from the Foot Switch Glow Sticker 2 Apply the Glow Sticker to the top of the Foot Switch StompLock To place the Stomp
5. following Important Safety Instructions Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Do not use this apparatus near water 5 Clean only with dry cloth 6 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 7 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 8 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 9 Unplug this apparatus during lightning storms or when unused for long periods of time 10 No user serviceable parts inside Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture 12 Refer to labels on the unit including bottom cover for other markings and pertinent information WARRANTY We at DigiTech are very proud of our products and back up each one we sell with the following warranty 2 Please register online at www digitech com wi
6. ied DigiTech technician or if the product is used with AC voltages outside of the range suggested by the manufacturer The foregoing is in lieu of all other warranties expressed or implied and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control NOTE The information contained in this manual is subject to change at any time without notification Some information contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed The information contained in this version of the owner s manual supersedes all previous versions Introduction More than a remarkable achievement DigiTech s HardWire series represents a collection of significant improvements in guitar effects pedals The HardWire series pedals provide a suite of well known effects each with superior tone and control But these pedals go above and beyond their peers to provide such distinguishing features as true bypass and high voltage operation making them essential additions to the signal chain of players who know about sound quality and demand the utmost in performance Included Items ardWire CM 2 Tube Overdrive StompL
7. k when not in use If the optional Harman power supply is used cables can remain connected Foot Switch Release Pins These two pins are spring loaded hinges that hold the Foot Switch in place See page 7 for information on accessing and changing the battery 9 Indicator LED Lights when the effect is turned on When battery power is low approximately 15 minutes before it dies the Indicator LED begins to dim giving you advanced warning that very shortly you will need to replace the battery 10 Foot Switch Turns the effect on and Output Connect this output to the input of your amplifier or the input of another pedal NOTE Use unbalanced mono instrument cables only Amplifier Setup a Harman Power Supply optional HardWit Tube Overdrive eS 3 Digilech Battery Operation In the event that battery power is completely depleted HardWire pedals automatically switch into bypass This eliminates the need to remove the pedal from your pedal chain if the battery is dead replace the battery do the following Using the tip of a 1 4 guitar cable push in one of the Release Pins on either side of the Foot Switch and remove it from the pedal chassis Remove the battery from the battery compartment and disconnect the battery cable Connect a new battery to the battery cable and put it back in the
8. ock Foot Switch Glow Sticker ook and loop Pedalboard Pad Online Warranty Registration Information Card Pedal Interface HardWire 2 Tube Overdrive What Does This Do Level Knob Controls the overdrive output level Turn the knob clockwise to increase and counterclockwise to decrease the output level DC Adapter Jack Connect the optional Harman power supply to this jack Use the proper supply for your area s mains line voltage Low Knob Controls the level of low frequency bass boost cut Turn the knob clockwise to increase and counterclockwise to decrease bass level High Knob Controls the level of high frequency treble boost cut Turn this knob clockwise to increase and counterclockwise to decrease treble level Gain Knob Controls the overall overdrive gain Turn the knob clockwise to increase and counterclockwise to decrease the amount of overdrive gain Voicing Switch This switches between the Overdrives two voicings Classic voicing provides the kind of gain you need for amazingly crunchy rhythms Modified voicing pushes your amp to the limits with just the extra gain you need for hot solos Input Connect your instrument or the output of another pedal to this jack This jack enables battery power to the pedal when connected To prolong battery life disconnect the cable from the Input jac
9. rocessing 8760 South Sandy Parkway Sandy Utah 84070 USA Ph 801 566 8800 Fax 801 568 7583 If you want to dispose of this product do not mix it with general household waste There is a separate collection system for used electronic products in accordance with mmm legislation that requires proper treatment recovery and recycling Private households in the 25 member states of the EU in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer if you purchase a similar new one For countries not mentioned above please contact your local authorities for a correct method of disposal By doing so you will ensure that your disposed product undergoes the necessary treatment recovery and recycling and thus prevent potential negative effects on the environment and human health ELECTROMAGNETIC COMPATIBILITY This device complies with part 15 of the FCC Rules and the Product Specifications noted on the Declara tion of Conformity Operation is subject to the fol lowing two conditions this device may not cause harmful interference and this device must accept any interference received including interference that may cause undesired operation Operation of this unit within significant electromagnetic fields should be avoided only shielded interconnecting cables WARNING For your protection read the
10. thin ten days of purchase to validate this warranty This warranty is valid only in the United States DigiTech warrants this product when purchased new from an authorized U S DigiTech dealer and used solely within the U S to be free from defects in materials and workmanship under normal use and service This warranty is valid to the original purchaser only and is non transferable DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect provided the product is returned to DigiTech WITH RETURN AUTHORIZATION where all parts and labor will be covered up to a period of one year this warranty is extended to a period of six years when the product has been properly registered through our website A Return Authorization number may be obtained from DigiTech by telephone The company shall not be liable for any consequential damage as a result of the product s use in any circuit or assembly Proof of purchase is considered to be the responsibility of the consumer A copy of the original purchase receipt must be provided for any warranty service DigiTech reserves the right to make changes in design or make additions to or improvements upon this product without incurring any obligation to install the same on products previously manufactured The consumer forfeits the benefits of this warranty if the product s main assembly is opened and tampered with by anyone other than a certif
Download Pdf Manuals
Related Search