Series K . Modules R2, R4, R6
Contents
1. User s Manual FEMA ELECTR NICA Series K Modules R2 RA R 1 Modules R2 R4 R6 Modules with 2 4 and 6 relays Modules with 2 4 and 6 relay outputs for K Series panel meters Re lays with 3 contacts each with switching capability up to 250 V 6A The R2 R4 and R6 modules provide setpoint configuration hyster esis independent activation and deactivation delays and second alarm setpoint for windowed alarms Modules R2 R4 and R6 are installed on slot Opt 1 see section 1 8 and are configured from instruments front keypad Index 1 ModulesR2 R4 R6 2 LE HOW to order 0 wa aaa m wer wand 2 1 2 How to install the R2 R4 R6 modules 2 1 3 Technical specifications 2 1 4 Rear view and connections 3 Lo FROME VIEW 4 iw nc ee Pe he es ee nad asa 3 1 6 Configuration menu 4 1 6 1 Alarm configuration 22 204 4224 ra 8084 4 1 6 2 Alarms 1 2 3 4 5and6 5 1 6 3 Factory reset 4 4 0 a apa bee ee erh 5 1 6 4 Firmware version Eur 5 1 7 To access the instrument 6 1 8 Modular system ee 6 1 9 Precautions on installation 1 1 10 Factory configuration 2 2 222er nen 7 1 11 CE declaration of conformity 7 1 12 Warranty 2 2 0 0 2 oa cyano ken ae ae a 7 1 1 How to order To order pre installed R2 R4 or R6 modules2. of the alarm The deactiva IES 1 III tion delay starts counting when the setpoint value plus the hyster DEL IT OOGGS esis value is passed Delay 1 Alarms can be configured with a second setpoint to work with win E FL 7 17 ooo da dowed alarms The first setpoint activates the alarm and the second Jeee mY A OOGG pear V setpoint deactivates the alarm configuration for Alarm as maxi 4 far F F mum type of alarm Second setpoint must always be higher in value than the first setpoint y e to activate the second setpoint activate Setpoint SEt2 to on and then configure the desired setpoint value Reading set point hysteresis Reading set point 2 Time set point 1 Alarm as maximum no hysteresis no delays on off Time Time on off Alarm as maximum with hysteresis and delays Time Alarm as minimum with double setpoint no hysteresis no delays Time on deactivation activation delay delay off on off Alarm as minimum no hysteresis no delays Time 1 6 Configuration menu cont lt A L FP Menu for Alarm 2 Available in modules R2 R4 and R6 H L Mm y Menu for Alarm 3 Available in modules R4 and R6 V_ H L Mm Ly Menu for Alarm 4 Availab
3. al plug in screw terminal pitch 3 81 mm terminals approved for 300 V according to UL1059 groups B and D and 160 V according to VDE on CAT III and pollution degree 3 FEMA ELECTRONICA Series K Modules R2 R4 R6 1 4 Rear view and connections 1 5 Front view Alarm leds Opt 1 Opt 2 acco mom AHA i Elle Uso I An I D ss O UW IS N Opt 3 Relay Common Normally Open Normally Closed NO NC Table 1 Connections for modules R2 R4 and R6 Detail of the plug in screw terminals provided with the instrument The instrument is provided with all terminals needed both male and female FEMA ELECTR NICA Series K Modules R2 RA R 1 6 Configuration menu To access the configuration menu of the module press the EM key for 1 second and then move through the menu with the 4 key until the Opt X entry corresponding to the slot were the module is installed see section 1 8 is displayed Press the M key to access the module configuration menu See the How to operate the menus section in the instrument user s manual for a detailed description on e select Active Act to on how to move through the menus 1 6 1 Alarm configuration To configure alarm 1 access the Alarm T ALr1 menu and config ure the fol
4. ent conforms to CE rules and regulations Instrument protected with double isolation No earth con nection required This instrument has been designed and verified conforming to the 61010 1 CE Security Regulation for industrial applications Installation of this instrument must be performed by qualified per sonnel only This manual contains the appropriate information for the installation Using the instrument in ways not specified by the manufacturer may lead to a reduction of the specified protection level Disconnect the instrument from power before starting any maintenance and or installation action 1 10 Factory configuration Alarms 1 2 3 4 5 and 6 Active on Type as maximum Setpoint 1 1000 Setpoint 2 2000 Setpoint 3 3000 Setpoint 4 4000 Setpoint5 5000 Setpoint 6 6000 Hysteresis O counts Activation delay 0 0 seconds Deactivation delay 0 0 seconds Setpoint 2 Off FEMA ELECTRONICA Series K Modules R2 R4 R 1 11 CE declaration of conformity FEMA ELECTRONICA S A Altimira 14 Pol Ind Santiga E08210 Barbera del Valles BARCELONA SPAIN www fema es info fema es Modules R2 R4 and R6 The manufacturer declares that the instruments indicated comply with the directives and rules indicated below Directive of electromagnetic compatibility 2004 108 CEE Directive of low voltage 73 23 CEE Security rules 61010 1 Emission rules Manufacturer Products 61000 6 4 Generic rules of emission Immu
5. into K Series panel me ters see the How to order section into the panel meter user s man ual for information on how to build the order reference To order standalone R2 R4 or R6 modules for delayed installation into K Series panel meters use the following ordering references BK R2 BK R4 or BK R6 Only one module R2 R4 or R6 can be installed per instrument Mod ules R2 R4 and R6 are not compatible with standard R1 modules The R2 R4 and R6 modules can be ordered pre installed into a K Series panel meter or standalone for delayed installation as they do not require soldering or special configuration 1 2 How to install the R2 R4 R6 modules To install a R2 R4 or R6 module into a K Series panel meter 1 open the instrument housing see section 1 7 2 install the module at slot Opt 1 see section 1 8 and close the instrument 3 configure the module as indicated in the Configuration menu see section 1 6 4 connect the signal terminals see section 1 4 1 3 Technical specifications Slots allowed Opt 1 see section 1 8 e Module R2 occupies Opt 1 e Module R4 occupies Opt 1 and Opt 2 e Module R6 occupies Opt 1 Opt 2 and Opt 3 2 with module R2 4 with module R4 6 with module R6 3 contact relay NC NO common Number of relays Type of relay Current maximum 6A per relay resistive load Voltage maximum 250 Vac continuous Isolation 2500 Veff Type of termin
6. le in modules R4 and R6 e A L m Menu for Alarm 5 Available in modules R6 H L nr E Menu for Alarm 6 Available in modules R6 cA T Acc r TE Factory reset LEE Il IIE _ LOGOL wer Anonn Version Vo FEMA ELECTRONICA Series K Modules R2 R4 R6 1 6 2 Alarms 1 2 3 4 5 and 6 To configure alarm 1 enter the Alarm 1 ALr1 menu see section 1 6 1 Menus Alarm ALr2 Alarm 3 ALr3 Alarm 4 ALr4 Alarm5 ALr5 and Alarm6 ALr6 control the configuration for alarms 2 3 4 5 and 6 and are identical to the Alarm 1 ALr1 menu Module R2 provides alarms 1 y 2 Module R4 provides alarms 1 2 3 and 4 Module R6 provides alarms 1 2 3 4 5 and 6 1 6 3 Factory reset At the Factory reset FAct menu select yes to load the default factory configuration for the instrument see section 1 10 1 6 4 Firmware version The Version VEr menu informs of the current firmware version installed in the module FEMA ELECTR NICA Series K Modules R2 RA R 1 7 To access the instrument You may need to access the inside of the instrument to add or re place internal modules Use a flat screwdriver to unlock the upper clips marked with A Then unlock the lower clips marked with B and remove the front cover Let the inside of the instrument slide out of the housing To reinse
7. lowing parameters e at Alarm type TypE select the alarm acting as a maximum II 1 1 E type alarm MAX or a minimum type alarm Min The maxi J Z mum type alarm or minimum type alarm activates when the dis play value is higher or lower than the setpoint value Hiri Act on orf ee an e at Setpoint SEt enter the value for the alarm activation point Alarm 1 Active i e configure the hysteresis value at Hysteresis hySt The hys COC Man teresis applies to the deactivation process of the alarm The alarm E AH L y EHEN deactivates when the reading has passed the setpoint value plus AON NYE AT the hysteresis value Hysteresis helps to avoid repetitive switching of the alarm relays due to fluctuating input signals around the set SEE HAABA point e ib Activation and deactivation delays have independent configuration parameters They are expressed in tenths of second and can be con Fu HHAA figured from 0 0 to 99 9 seconds Hysteresis e at Delay0 dEL 0 configure the activation delay The activation delay will delay the activation of the alarm The activation delay cde LE gt Al A HH starts counting when the setpoint value is passed Delay 0 e at Delay1 dEL 1 configure the deactivation delay The deacti vation delay will delay the deactivation
8. nity rules 61000 6 2 Generic rules of immunity 61000 4 2 By contact 4 KV Criteria B By air 8 KV Criteria B 61000 4 3 Criteria A 61000 4 4 On signal lines 1 KV Criteria B 61000 4 6 Criteria A 61000 4 8 30A m a 50Hz Criteria A Barbera del Valles November 2012 Daniel Junca Quality Manager 1 12 Warranty This instrument is warranted against all manufacturing defects for a period of 24 MONTHS from the shipment date This warranty does not apply in case of misuse accident or manipulation by non autho rized personnel In case of malfunction get in contact with your local provider to arrange for repair Within the warranty period and after examination by the manufacturer the unit will be repaired or substi tuted when found to be defective The scope of this warranty is lim ited to the repair cost of the instrument not being the manufacturer eligible for responsibility on additional damages or costs
9. rt the instrument make sure that all modules are correctly connected to the pins on the display module Place all the set into the housing assuring that the modules correctly fit into the internal guiding slides of the housing Once introduced place again the front cover by clipping first the upper clips A and then the lower clips B Important If your instrument was delivered with the IP65 front seal option accessing the inside of the instrument will permanently break the IP65 seal on the areas of clips A and B Risk of electric shock Removing the front cover will grant access to the internal circuits Disconnect the input signal to prevent electric shock to the operator Operation must be performed by qualified personnel only 1 8 Modular system K Series panel meters are designed to create a modular system This modular system allows for addition replacement or substitution of any of the internal modules conforming the instrument Below is a graphic explanation for the position of each module Front Filter Zs Display Module Optional Control Modules N x Power Supply Module Opt 3 Input Signal Module Housing 1 9 Precautions on installation A Risk of electrical shock Instrument terminals can be con nected to dangerous voltage C Instrum
Download Pdf Manuals
Related Search