Home
T-862 user`s manual in English
Contents
1. adjust the infrared lamps temperature at 300 350 The infrared ray lights directly infrared ray is the strongest when the temperature is up to 350 you need pay attention to the timing and prevent from burning out the chip 5 Adjust the focus The minimum focal diameter of infrared lamp body is 15mm the maximum is above 30mm adjust them according to different chips Usually the ideal height between lamp and the chip is 20 30mm Adjust the focusing knob by the size of the chip Ideally the bright spot Http www tech168 cn 9 IRDA Workstation T862 User Manual should cover the whole chip 6 Turn on the two switches on the front panel for the pre heating plate and the infrared lamp 2 Unsoldering operation Adjust temperature make the center of the infrared lamp aim at the unsoldered chip Http www tech168 cn 10 IRDA Workstation T862 User Manual 3 Soldering operation Clean up the welding plate with a brush 2 Put the tin ball and spread soldering flux not too thick only a thin layer of it on the soldering plate 8 Put the chip in the accurate place after the solvent volatilizes out of soldering flux heat the tin ball until it melts and solder the chip Http www tech168 cn 11 IRDA Workstation T862 User Manual 4 Using the lead free soldering iron Switch on the power set the temperature that you need turn on the switches Caution 1 Do not cut the power off right after
2. IRDA SMD amp BGA Rework Station T862 User Manual TAIAN PUHUI ELECTRIC TECHNOLOGY CO LTD www tech168 cn IRDA Workstation T862 User Manual CONTENT 1 Fe ttr CS hc ciscs tnwcwiasicsedbininisvien san womincaeiewiepuieisisws ii iE s 2 2 Technical Parameters sede seaesectdeesseusisrienses 2 3 List OF content ossos peas senori iEn E a EEs ipe ERE aS 2 4 Description of the main parts 3 CL Main DOGY sssi sentes ceni eri iii iana ideoi i n s a 3 2 Front PaAmels cicaunassvarins aise e nae iE E E 4 3 Back Panel iis ects sssocsssssosirossscssssssessossdos riso st caderadateveseduens 4 4 Focusing Support pp 5 D5 Installaatio Mh siceisossion nis csinsnssiniawe ois vas Caiwren abs seinne eeens 6 1 Install the guide 100 pp 4 2 Install the locating ring 5 3 Complete Assembly ssseessosssessssesoossssesssoossessessesssssseseo 5 4 Connecting wire of the lamp body pe 7 6 Operating instructions 7 D Staring nosses nnee sesan EEE eSEE Ei a 7 2 Unsoldering Operation cccsccccccccceccccccsccccsccsccecccees 8 3 Soldering operation pp 8 4 Using the soldering iron 9 te EALA CI 9 S Warranty 10 Http www tech168 cn IRDA Workstation T862 User Manual Features Use of infrared welding technology which is developed independently Use of an infrared heat lamp Heat is easy to pierce and distribute evenly which overcome disadvantage burn out elements of traditional welding
3. machines Easy operation You just need one day training and you can operate it skillfully No need for unsolder tools IRDA Welder T 862 can unsolder all the elements between 15 and 25 mm This machine has 350W hot melt system Its preheating area is 80x 120mm Infrared heating without heated air flowing No impact on circumjacent small elements It is suitable for all of the elements especially Micro BGA elements Http www tech168 cn 2 2 Technical parameter IRDA Workstation T862 User Manual Working Voltage ae Output power 600W Infra red lamp body temperature adjustable 100 C 350 C Preheating dish temperature adjustable 60 C 200 C Components Description Quantity Welder base 1 Guide rod 1 Locating ring 1 Lamp assy 1 Circuit Board PCB support 1 Power Cable 1 Soldering iron 1 Soldering iron support 1 User Manual 1 Http www tech168 cn IRDA Workstation T862 User Manual T 862 illustrated explaining 1 The whole machine Protection Cover of the fan The end covering Focus holder Lamp body Filter and Cover 936 soldering iron support 936 soldering iron Focusing knob Front panel Http www tech168 cn 4 IRDA Workstation T862 User Manual 2 Front Panel Infrared lamp Peak temperature 936 temperature display Preheater plate temperature display Infrared Lamp Swi
4. tch soldering Iron Switch Preheater plate Switch moa SMB amp BGA Rework Station SS0LPING Hie wwieelectron tools com Temperature level regulation Button Back Panel Connecter for Connecter for 936 Power Input infrared Lamp soldering Iron Ot DING IRON IRDA LIGHT GUN Http www tech168 cn 5 IRDA Workstation T862 User Manual 3 Focusing support IR Lamp Cooling Fan Guide rod Focusing knob 3 Q Focusing support Pinch nut of focusing support Pinch nut of locating ring Locating ring Http www tech168 cn IRDA Workstation T862 User Manual Installation 1 Install the guide rod Loosen the pinch nut of focusing support put the guide rod in according to the direction of arrow icon pointing Note The Infrared Head Body Mounting and Focus Assembly will be installed in the T 862 chassis later The direction of guide rod S 2 Inventory all Items confirm no parts are missing If parts are missing call 0086 538 6138575 3 Put the locating ring in Loosen the pinch nut of locating ring put the locating ring in according to the arrow icon pointing and fasten the nut to the appropriate height Locating ring The direction of the locating ring 4 Machine Assembled Loosen the pinch nut of focusing support Http www tech168 cn 7 IRDA Workstation T862 User Manual Pick up focusing support make
5. the guide rod aim at the corresponding nut on the base then rotate the guide rod Fasten the focusing support by rotating pinch nut of it Rip off the protective film of the filter pre Rotation Direction 5 Connecting the wire of the lamp body Get the adapter of connecting wire plug in the socket of infrared lamp connecting wire Rotate set screw clockwise 6 Attach IR Eye protective filter with the supplied screw and nut T 862 Operation Circuit Board Support Welder base work bench Http www tech168 cn 8 IRDA Workstation T862 User Manual 1 Starting 1 Inspect the infrared lamp body temperature sensor and power line and see if they are in good connection 2 Turn on the power switch then use self checking first The previous setting value demonstrated on the keyboard display monitor after you turn on the machine 3 Put PCB on the corresponding notch in PCB support and adjust the pinch nuts of locating ring and focusing support then adjust the height of infrared lamp body the ideal height between lamp and the unsoldering article is 20 30mm 4 Select the suitable heating temperature Select the suitable heating temperature of infrared lamp between 100 350 C according to the chip size that need to be unsoldered When you unsolder chips which are about 15x15mm you adjust the infrared lamp s temperature to 240 300 C When unsoldering chips which are about 30x30mm you
6. the work finished You need to wait until the fan cools down the lamp body 2 Keep the lamp body clean and the ventilation opening free of any obstructions 3 The guide rod and the focusing support should be spread with lubricant regularly 4 Pull out the power plug if you don t use it for a long term 5 Be careful of operating under high temperature conditions Http www tech168 cn 12 IRDA Workstation T862 User Manual Warranty statement Reminder These machines are very heavy between 8 to 15 kilograms and are not designed to be shipped on airplanes but in containers that do not move We are not the shipping company the airplane crew the customs agent or the carrier in your country and therefore take no responsibility for damage caused in transit Corollary When our machines leave QC they are tested 100 new and in perfect condition These machines consist of modules Should you receive a faulty or damaged module we will be happy to replace it However we will not replace the complete machine this is not covered by our warranty PUHUL is responsible to give proper guidance of the use and installation of the machine if you don t follow these it will void the warranty Http www tech168 cn 13
Download Pdf Manuals
Related Search
Related Contents
REFERENCE GUIDE Aero 2100 Series Color Palm 07AS Yes, No, Maybe So SMC Barricade SMCWBR14S-N4 router PowerPlay: Creating Virtual Power Meters Acerca deste Equipamento - Firmware Center T07-08-02_Reliability_Analysis_D7_1_Appendix kit marco.pub - Monitorhalterung.de Copyright © All rights reserved.
Failed to retrieve file