Home

BALE KING V-RAKE VMAX 1214 User Manual Bridgeview

image

Contents

1. Tire warranty is covered by the tire manufacturer 14 WHEEL EXTENSION The 12 wheel rake can be fitted with an extension kit This kit extends the length of the rake arms adding one rake wheel to each side making the rake a 14 wheel rake This option increases the area covered by the rake and can be purchased as a separate kit to the 12 wheel rake HYDRAULIC HOOK UP There are six hydraulic hoses to be connected to the tractor All six hoses run out of the gooseneck of the rake near the hitch The hose marked with green controls the wing cylinder used to open and close the rake arms The hose marked with blue controls the windrow adjustment cylinder to change the width of the rear opening and the size of the windrow The hose marked with yellow adjusts the lift arm cylinders used to raise and lower the rake wheels These hoses should be connected to the most convenient hydraulic hook ups on the tractor The long green and blue open the rake while the long yellow lifts the rake wheels HIGHWAY TRANSPORT When transporting your V Rake on the highway there are a number of safety precautions that must be taken to ensure safe travel First is to insert the cylinder safety locks The lift arm cylinders located on the left and right rake arms should be fitted with cylinder safety locks To insert the safety locks raise the rake wheels to their highest position then insert the safety lock Cylinder Lock Cylinder Ensure that
2. spring that allow the spring to be loosened or ye 2 TINE REPLACEMENT lf a tine on one of the rake wheels needs to be replaced the following procedure can be used e The bolt on the back of the rake wheel that corresponds to that tine should be loosened and removed completely e Slide the tine out of the hole in the center disk e Slide the tine out of the wind guard tab if necessary e Slide the tine out of the hole in the outer ring e Insert the replacement tine in the same direction as the other tines on the rake wheel e Then insert the bolt back in to the wind guard and tighten the nut Wind Guard Tooth Wind Guard Clip SPECIFICATIONS Overall Length 33 5 Overall Width 10 1 Overall Height 6 8 Overall Weight 12 4813 165 14 5605 Ibs Tire Size 9 5L15SL 8Ply Tire Pressure 37 psi Torque Settings Wheel Bolts amp Nuts 1 2 Dry 90 Lb 9 16 Dry 120 Lb 10 NOTES
3. BRIDGEVIEW BALE KING V RAKE VMAX 1214 User Manual Bridgeview Manufacturing Inc P O Box 4 Gerald SK SOA 1 0 306 745 2711 Email bmi sasktel net www bridgeviewmanufacturing com TABLE OF CONTENTS TABLE OF CONTENTS nn ae INTRODUCTION es aaa SAFETY PRECAUTIONS nu MACHINE MAINTENANCE AND LUBRICATION WHEEL AND TIRE WHEEL EXTENSION sirieni ueniren HYDRAULIC HOOK UP ua HIGHWAY WINDROW WIDTH FIELD OPERATION ADJUSTING WHEEL ARM SPRING 2 0200 00 TINE REPLACEMENT SPECIFICATIONS an re INTRODUCTION Thank you for purchasing your new Bale King V Rake With the proper operation and service as outlined in this manual this V Rake will provide you with years of trouble free operation SAFETY PRECAUTIONS The following safety precautions MUST be followed to ensure the safe operation of the Bale King V Rake 1 This trailed machine was designed and intended for on farm use only Tow at speeds not to exceed 20 MPH Slow down for hills curves rough areas and in advance of braking to prevent loss of control and possible injury or death Always turn off the tractor when leaving the operating platform Always use the transport links when towing the V Rake on the hig
4. hway Unless operating tractor stand clear of the rake when in operation Do not stand inside the rake while it is being opened or closed oe D MACHINE MAINTENANCE AND LUBRICATION General maintenance of your V Rake should be done on a regular basis This includes checking all bolts to ensure they are tight making sure all grease zerks are accepting grease and ensuring that all moving parts are functioning correctly Your Bale King V Rake is equipped with a number of grease zerks It is important that these locations are lubricated according to the following maintenance schedule Wheel hubs for the tires and rake wheels should be greased every 200 hours of use Knuckles caster pivots wheel arms and any remaining grease zerks should be greased every 10 hours use Grease Zerks 1214 V Max Rake Caster Cylinder Pins Not Shown Wheel Rake Hubs gt ER 5 a A 0 __ Rake Wheel Arms all Hubs Knuckle and Box WHEEL AND TIRE INFORMATION The proper tire pressure for the Bale King V Rake is 37 psi Proper tire inflation will help alleviate a puncture problem when pulling and operating the machine in rough terrain The optimum tire size is 9 5L15SL 8 Ply NOTE Check and tighten wheel bolts on a regular basis to ensure that bolts are tightened to 90 ft lb Warranty does not cover damaged rims and hubs due to loose wheel bolts
5. indrow to suit field conditions and accommodate different baler sizes Rake wheel arm open and close Windrow width adjustment FIELD OPERATION The recommended raking speed is 8 mph 13 km h depending on field conditions Rougher land and heavier windrows require slower operation This will prevent damage to the rake wheels and ensure that hay is picked up properly For faster operation it is recommended that rake wheel spring tension is increased to prevent bouncing of the tines ADJUSTING RAKE WHEEL ARM SPRING TENSION Optimum rake performance is achieved when the rake wheels are lightly scraping the ground Ifthe spring tension is set too heavy premature rake tine damage will occur If tension is too light the hay will not be properly picked up If the tension in the spring arms needs to be adjusted there are a number of ways to accomplish this The first is by moving the threaded rod adjusters The threaded rod adjusters are located at the rear end of each rake arm and are directly attached to the lift rod cylinder By adjusting the bolts attached to the rod adjusters the tension in all the springs of that rake arm are adjusted evenly To increase tension decrease length x as shown below To decrease tension increase length x Adjust Spring Tension Here lf the spring tension in only one spring needs to be adjusted then the adjustment can be done on the individual spring There are two nuts near the end of the
6. the rear opening is in the narrow position by fully stroking the windrow adjustment cylinder Then bring in the arms by retracting the wing cylinder until the front castors are brought in near the hitch The transport links must then be installed First remove the links from the carrying brackets by removing the pin at each end as shown below Transport link pins Next insert the large end into the bracket at the bottom of the main frame Pull out the self locking pin and allow the inside tube to freely slide then insert the small end into the bracket on the arm Retract the wing cylinder until the self locking pin locks in transport position Ensure that both arms are secured and all hairpins are in place Self locking pin Locked Align the road wheels and tighten the brake springs for all casters The caster wheels will whip if the brakes are not sufficiently tight Tighten this nut Ensure that all of the tires are at the correct pressure and that all wheel bolts are secured WINDROW WIDTH ADJUSTMENT The rear opening of the V Rake is adjustable using the windrow adjustment cylinder It must be in the narrow position to be able to transport on the highway Widening the rear opening will space the rake wheels further apart creating a wider windrow Pulling the rear opening closer together will also pull the rake wheels closer together and make a tighter swath This allows the operator to adjust the width of the w

Download Pdf Manuals

image

Related Search

Related Contents

Echo CS-510 User's Manual  C-VX870 C-VX872 取扱説明書  取扱説明書 - 三菱電機  XFINITY® HOME SECURITY USER MaNUal  Samsung SGH-D780 manual de utilizador  Manual de Usuario ADInstruments AD300  Nuova Direttiva MacchinePDF - Benvenuto su www.wpsitalia  Categoria 3 ISAF OSR  Pregnancy test for visually impaired women Tereza Hyková  Descargar  

Copyright © All rights reserved.
Failed to retrieve file