DOCKING GPS – GSM User Manual
Contents
1. ll PROFESSIONAL TIMING DOCKINGGPS GSM User Manual Version 11 2009 1 General e The GPS Docking is equipped with a Li Ion accumulator ensuring exceptional autonomy for the Chronoprinter 540 even at very low temperatures 20 C 4 F e Asatellite detection module GPS ensures the automatic Time of Day synchronization and precision control e A GSM communication modem allows wireless connection between two CP540 s through the mobile telephone network ILE Power Output Top Minute Antenna GPS Output SE Connector leer gt Slave a System A Master gt Slave System A Antenna GS Charge LED Connector e RESET button in case of a problem with the Docking To RESET press the mini contact located under the identification plate of the Docking Use a small blunt instrument to gently depress Important recommendation e To guarantee the security of your timekeeping it is necessary to use your CP 540 with the internal batteries in a charged state e Do not forget to charge the Docking before its use see How to charge the Docking gt e If the system is not used for several days we recommend that you disconnect the Docking from the Chronoprinter and remove the batteries from the CP 540 e Do not forget to replace the red blanking plug into the DOCKING on the CP 540 to protect its connector e Protect the Docking with its original packing e We recommend you to use the synch2. C Delta 15 sec Then GPS ready for Synchro Validate 2 times under GSP to make the Synchro mode Synchro The synchronization of Time of the Day with the correct date is automatically made REMARK UTC TIME The time provided by the satellites is GPS terrestrial hours of a certain number of seconds 15 seconds since January 2009 This information is transmitted by satellites every 12 5 mins It remains in the GPS almanac this allows fast synchronization WARNING When you remove the GPS antenna connector hold the connector firmly Never remove or hold by the cable 5 Remarks on GPS gt If GPS signal is Lost poor positioning of the antenna the printer indicates Synchro GPS lost The time of day The display time of day will flicker along with GPS LOST If the GPS signal is synchronized again the printer indicates repositioning of the antenna GPS Active Synchro GPS found Time of the day DEV 3 0 usec for example Remark Automatic resynchronization of the time base of the CP 540 temporary loss of GPS signal is acceptable in conditions where the drift of the time does not exceed 100 usec 1 10 000 of a second In case of resynchronization the drift DEV is always printed If the drift value is over 100 usec the base time of the CP 540 is the reference for the rest of the time keeping The GPS can be switched OFF If the Docking is disconnected the printers indicates Do
3. G Tighten all the screw slightly then while being conscious that you screw in plastic tighten a little more without over tightening risk of damage to the plastic We advise against the repeated opening and the closing of the Docking For the Pre paid SIM Card it is generally possible to top up the SIM Card via the internet Choose a telecom company with wider broadcast coverage It is also possible to have a SIM Card with an annual subscription Do not forget to write your phone number on the back of the Docking even if it is memorized in the Chronoprinter 540 Do not cross CP 540 and Docking Suggestion place a small green sticker on the CP 540 and Docking for the Start and red for the Finish 8 Information gt gt gt The GSM GPS Docking has banana output connector to provide a signal TOP MINUTE which is useful to synchronize other timing systems If the GPS is used only for the CP 540 it is recommended to wait 4 5 mins before to switching it OFF memorize the GPS precision The GSM GPS Docking has an Input output Master Slave This mode of synchronization between several CP 540 s is very useful for the timekeeper to guarantee absolute precision between different systems For example System A Master and the back up system B Slave Connect the CP 540 A Master to CP 540 B Slave with the special cable HL540 11 The CP 540 A is synchronized with the Tim
4. cking It is not necessary to do this setting each time as this information is stored Important if you download a new software version you will lose your settings For further information please read the user s manual Server GPRS available on www tagheuer timing com Select GPRS mode and validate by pressing on ENTER a As soon the docking is connected to your server the printer will print CONNECTION ETABLISHED You GPRS connection is now ready to transmit times ATTENTION The GPRS mode could take a couple of 1 10 seconds to transmit data NOTE It is very important to read carefully the user s manual of TAG Heuer CP540 Server 7 How to insert the SIM Card in the Docking Use a Standard SIM Card annual subscription or with pre payment To guarantee a bidirectional communication between CP 540 s it is necessary to have two GSM Docking stations with SIM cards with a different telephone number Proceed to the following steps Unscrew the 5 screws on the back of the Docking with a Phillips screwdriver N 1 Carefully remove the upper cover Place the SIM Card from the top into the support with the 45 angle at Top Left Push the card gently downwards SIM Card Replace the upper cover return the Docking and secure gently the 5 screws while checking that the two parts are well positioned Press on the top of the Docking when you tighten the screws WARNIN
5. cking disconnected Synchro GPS lost Time of the day When the Docking is reconnected the printer indicates Docking Connected with its serial number and Software version GPS Searching with GPS UTC Delta 15sec GPS Active Synchro GPS founded Time of the Day DEV 2 4 usec for example 6 How to use GSM ATTENTION The SIM Card should not have PIN number Please disable any SIM PINs via your SIM provider instructions 6 1 General e Fitthe GSM antenna to its connector e Switch ON the CP 540 by pressing the Key ON for 5 seconds e The LCD display shows o Docking with 4 arrows directed to the top arrow outgoing These arrows show the status of the 4 Data communication outputs via RS232 or GSM o Charge status of the Docking ex 85 or Power supply presence o GPS OFF o GSM OFF e The incoming message of the CP 540 is printed with indication Docking connected its serial number and software version e Validate OK by pressing on ENTER lt A The Docking menu shows o Status of the Docking o GPS ON OFF o GSM ON OFF If the GPS is used for the Synchronization please refer to the chapter how to use GPS If the Synchro with GPS is not used the display shows Mode Synchro select Manual or External Synchronize both CP 540 with the same date and time e As soon the Synchro is done come back to Docking GSM ON OFF o Select GSM ON and validate o The LCD shows the Input E1 to E4 Stat
6. e of Day manually or with GPS The CP 540 B is automatically synchronized by the CP 540 A by choosing Master Slave in the Synchro Menu If the Main system A is disconnected or communication fails the back up system B will operate with its own time of base The Drift DEV described later Synchronization by GPS is also into the mode Thus if the Main System A is again operational it will take its main function as Master if the Drift is lower that 100 usec All information is of course printed How to charge the Docking accumulator The Docking can be charged seperately or connected to a CP 540 Charge the docking with the power supply HL 540 1 from the CP 540 Connect the power supply to the POWER connector of the Docking connector 3 poles The LED located at the bottom of the Docking allows you to see the charging status o LED is red during the charge 6 hours for a complete charge o LED is green when the docking is fully charged e When the CP 540 is used with the Docking the external power supply should be connected to the CP 540 WARNING The Docking should be not charged in temperatures lower than 0 C 32 F Remarks The charging status of the Docking is displayed on the CP540 LCD if charged together If the Docking is too discharged the batteries of the CP 540 will power the system If the power is too low the Time on the LCD will flicker and the printer will print Low battery before to switching OFF au
7. l have access to GSM Hang Up Use this option to close the communication if you don t need the communication for a long period to save cost of communications To restore the communication use Modem on one of the systems In case of temporary lost GSM communication or poor reception of signal the caller system will try to automatically to re establish the communication All timing information not already transferred will be automatically stored and then transmitted when the connection is re established 6 3 GPRS mode The GPRS General Packet Radio Service is an extension of GSM protocol This mode is more adapted to the data transmission The resources are allowed only when data is being transmitted contrary to the CDS mode where the communication is allowed constantly O O O O Set the communication parameters via RS232 Use the program CP540 GPRS setting available on www tagheuer timing com Set the Access Point User ID Password if necessary Domaine Name or IP address sure as port number HE CP540 GPRS Settings loj x Serial Port COM1 sl Print Current Settings Access Point Name gprs swisscomch User ID IT Password IT Domain Name IP thtiming dyndns org Port 1505 Save New Settings For countries and operator the access point name is different It is necessary to contact your operator to get this information or via internet This information should be saved to the Do
8. mode CDS and valid by pressing on ENTER lt A LCD shows Modulation gt V 32 related to the analog networks gt V 110 related to the numerical networks Select V 110 the more popular choice for communicating Modem to Modem GSM Ready and Modem Setting V 110 are printed Choose Modem on the CP540 which calls the other CP540 Validate Compose the phone number of the second CP 540 and validate Call Modem is printed on the caller CP 540 Income Call is printed on the called CP 540 Connection Established is printed on both CP 540 s when the bidirectional communication is established ATTENTION The GSM connection can sometimes be difficult to establish If the connection Start Finish is not established after 3 or 4 automatic calls you can try to call the Start from the Finish or switch GSM OFF and then ON again on both systems There also exists on the market GSM antennas to ensure better communication When the communication is established the cost is the same as normal handy standard communication This communication could be expensive in certain cases But this communication offer you the possibility to work in real time no delay due to the communication as you have with GPRS communication The main menu has the indication DOCKING It is possible to check the status at anytime or battery status GPS Active or number of satellites Important information In the menu Docking you wil
9. ronization by GPS between two CP 540 which are communicating Modem to Modem The precision is thus guaranteed for your timing e If you do not wish to use the Synchronization by GPS please be sure to input the same date and time on both systems before synchronizing them IMPORTANT It is essential to update the software inside the CP 540 Docking before initial use You will find the software version on our internet site www tagheuer timing com Docking connection e Remove the DOCKING red blanking plug gt from the CP 540 which gives access to the docking connector e Place the DOCKING red blanking plug on the Docking at the reserved position under the female connector e Place the CP 540 on the DOCKING and press firmly to ensure a good connection 4 How to Use GPS e Carefully connect the GPS antenna cable in the socket 21 The GPS antenna must be installed in a clear open place outdoor with an unobstructed view of the sky in e Menu O O O order to correctly receive the satellite signals generated by the GPS system GPS ON OFF Select GPS ON and confirm Select the time difference between GMT time and your time zone ex GMT 2 in the west of GMT or GMT 2 in the east of GMT Validate your choice this information is stored in memory The display shows initially GPS Searching then GPS Active as soon as it locates several satellites GPS Searching is also printed with the indication GPS UT
10. tomatically When the charge indicator of the Docking shows 50 on the LCD Docking Menu you still have at least 4 hours of autonomy 10 Technical specification General 0000 Accumulator GPS GSM O O O 0000 O Operating condition 20 C to 60 C External power supply 12Vdc Top minute output optocoupler Connector IN OUT for Master Slave 2x RJ13 Type 7 4V Li Po 2700mAh Charging condition 0 to 40 C Charging current 500mA 5 5 hours Precision 50 n seconds 50 x 10 9 sec Current consumption when activated 30 mA when GPS is actived 12 channels continuous tracking receiver Connector for external antenna Quad band EGSM 850 900 1800 1900 MHz Output Power e Class 4 2W from 850 900 MHz e Class 1 1W from 1800 1900 MHz Data transmission e CDS 9600 Bds V 92 V 110 Modem e GPRS Class 10 Standby consumption 63 mA Average consumption in Modem Mode 197 mA Connector for external antenna KE TAGHeuer PROFESSIONAL TIMING TAG Heuer PROFESSIONAL TIMING 6A Louis Joseph Chevrolet 2300 la Chaux de Fonds Switzerland Tel 032 919 8000 Fax 032 919 9026 E mail info tagheuer timing com Http www tagheuer timing com
11. us with 4 arrows These arrows indicate the direction of data either transmit or receive of the timing information from one Chronoprinter 540 to another The status of each input can be modified by pressing the respective E1 Ed It is possible to receive at the Start the Finish Time and at the Finish the Start times Both CP 540 s will receive all information to edit results and ranking Example with one CP 540 at the start and another at the Finish Timing Mode NET TIME CP 540 at the Start With E1 program an outgoing arrow N to transmit the times of the Start to the Finish With E2 and E3 program because these are used to transmit or receive data for sector timing etc With E4 program the entering arrow V to receive the arrival time CP 540 at the finish With ET program an entering arrow V to receive the Start times to the Finish With E2 and E3 program because these are used to transmit or receive data for sector timing etc With Ed program the outgoing arrow N to transmit the Finish time Once the module GSM is enabled the display shows GSM Ready o Validate OK by pressing on ENTER lt A 6 2 Mode CDS Circuit Switched Data The Circuit Switched Data CSD is the original form for data transmission developed for the Ime division multiple access based mobile phone systems like Global System for Mobile communications GSM O O 0000000 Select the
Download Pdf Manuals
Related Search