49024 SS procedure headlight user manual
Contents
1. WelchAltyn Solid State Procedure Headlight System REF 49020 49022 49024 49026 Part No 460134 Rev B A bol Description Attention Consult user s Manual for additional Double Insulation information ATTENTION Read Operating Manual for Warnings Cautions and Instructions for Use WARNING Solid State Procedure Headlight is not suitable for use in the presence of a flammable anesthetic mixture with air or oxygen or nitrous oxide An explosion may result AN IPX Not protected against the ingress of water INTENSE LIGHT Lamp is bright Do not stare at the lamp when in use May be harmful to eyes USE ONLY Solid State Procedure Headlight Power Source Battery Charger and rechargeable battery pack supplied by Welch Allyn l There are no userserviceable parts inside the device except the rechargeable batteries and headband Contact the Authorized Service Center listed at the end of this document for further assistance Guidelines for the safe use of the Solid State Portable Headlight General practices to minimize risk of harm to the skin from optical radiation hazards include minimizing illumination AN intensity at the tissue examination site minimizing exposure times and taking additional precautions when skin sensitivity has been altered through tissue trauma or the use of anesthesia General good practices to minimize risk of harm to the eyes from optical radiation hazards include Avoiding looking at b2. 1060 Altitude storage Transport 4 F 120 F 20 C 49 C 95 RH Max continuous 500 hPa 1060 Altitude Equipment Classification Class II Continuous Operation IPX Not protected against the ingress of water Category Not AP APG Equipment This device complies with current required standards for electromagnetic interference and should not present problems to other equipment or be affected by other devices As a precaution avoid using this device in close proximity to other equipment Approvals CERTIFIED TO CAN CSA STD C22 2 NO 601 1 CONFORMS TO IEC 60601 1 IEC 60601 1 2 UL STD 60601 1 AS NZS 3200 1 The CE mark on this product indicates that it has been tested to and conforms with the provisions noted within the 93 42 EEC Medical Device Directive Authorized European Representative Address European Regulatory Manager Welch Allyn Ltd Navan Business Park Dublin Road Navan County Meath Republic of Ireland Tel 353 46 90 67700 Fax 353 46 90 67754 Complies with EMC Framework of Australia Power Sources UL Recognized US Canada UL2601 1 CAN CSA C22 2 No 601 1 VDE Certified IEC 60601 1 EN 60601 1 VDE 0750 Warranty Instrumentation purchased new from Welch Allyn Inc Welch Allyn is warranted to be free from original detects in material and workmanship under normal use and service for a period of one year for the Solid State Procedure Headlight from the date of Tirst shipment trom Welc
3. environment Emissions Test Electromagnetic Environment Guideance Ar EMISSIONS e 49000 uses H y TOT i emissions are CISPR11 Group 1 very low and are not likely to cause any interference in nearby electronic equipment Leakage Current Electromagnetic Environment Guideance eco 1 1 CISPR11 Class B Harmonics IEC 61000 3 2 Class A The REF 49000 is suitable for use in all establishments including domestic and those directly connected to the public low voltage power supply network that supplies buidlings Flicker IEC 61000 3 3 Complies wd used for domestic purposes Radiated and Conducted Emissions were tested on the FRIWO 15 1504 power supply It complies with the EN55022 Class B limits same limits as EN55011 Group 1 Class B Harmonics and Flicker testing were performed on a REF 46000 with a 230 VAC FRIWO 15 1504 power supply Guidance and Manufacturer s Declaration Immunity The REF 49000 is intended for use in the electromagnetic environment specified below The customer or user of the REF 49000 should ensure ul it is used In such an environment IEC 60601 Test Level Compliance Level Electromagnetic Environment Guidance O 6kV Contact ontact 6 8kV Contact ontact oors SNOUIA De Wooa Floors should be wood concrete or ceramic or ceramic n 61000 4 2 a Air 15kV Air tile If floors are synthetic the r h should be at i least 30 EFT 2kV Mains oO Mains power quality should be that of a typ
4. Aston Abbotts Fax 86 21 6327 9632 Buckinghamshire England HP22 4ND Tel 0 207 365 6780 Fax 0 207 365 9694 Welch Allyn 4341 State Street Road Skaneateles Falls NY 13153 Tel 800 535 6663 or 815 685 4560 Fax 315 685 3361 www welchallyn com
5. ansmitters as determined by an electromagnetic site GHz survey should be less than 10Vrms or 10V m Interference may occur in the vicinity of equipment containing a transmitter Conducted RFI and Radiated RFI testing was performed on a FRIWO 15 1504 power supply monitoring the output for drops in voltage none were detected Recommended Separations Distances between portable and mobile RF Communications equipment and the REF 49000 The REF 49000 is intended for use in the electromagnetic environment in which radiated disturbances are controlled The customer or user of the REF 49000 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF Communications Equipment and the REF 49000 as recommended below according to the maximum output power of the communications equipment Separation m Separation m Separation m Separation m 150kHz to 80MHz 150kHz to 80MHz 80 to 800MHz 800MHz to 2 5GHz Non ISM ISM D 3 5 E1 D 7 E1 D 3 5 V1 D 12 V2 Sprt P Sprt P Sprt P Sprt P Max Output Power Watts Dimensions Headband Adjustment Range small Medium Large Illumination System 5 watt Solid State Lamp Color Temperature 5500 Degree Kelvin 50 Lumens LED lite gt 10 000 hours Working distance 16 inches Spot size range 1 5 to 6 inches at the working distance Weight 6 ounces Environment Operating 32 F 104 F 0 C 40 C 75 RH Max continuous 500 hPa
6. enous and well defined spot gt Follow the assembly instructions listed below and the corresponding photographs Connecting Headlight to Portable Power Source Portable Power Source 1 Plug the instrument power cord into the power cord connector port on the top of the power SOUICE Push in until it is firmly in place 2 3 Gently screw the external connector sleeve clockwise to secure Recharging the Portable Power Source Power Cord Recharging the Portable Power Source On Off Switch Turn the portable power source off Disconnect instrument from power source Plug charging transformer into portable power source N Plug charging transformer into wall socket LED light indicates unit is charging Sea Disconnect charging transformer from power source when fully charged approximately 10 12 j hours Maintenance Each month examine cords and connections The user can perform battery and or headband replacement on an as needed basis Return the unit to an authorized Welch Allyn Technical Service Department or distributor for additional servicing See Service and Warranty Information section OL NS Cleaning Recommended monthly Excess solution entering the luminaire assembly could damage internal components Use caution to ensure cloth is not saturated with solution 1 Unplug the unit prior to cleaning 2 Wipe down the entire luminaire with a cloth slightly dampened with a mild solution of detergent 3 Do
7. h Allyn This warranty shall be fulfilled by Welch Allyn or its authorized representative repairing or replacing at Welch Allyn s discretion any such defect free of charge for parts and labor Welch Allyn should be notified via telephone of any defective product and the item should be immediately returned securely packaged and postage prepaid to Welch Allyn Loss or damage in shipment shall be at the purchaser s risk Welch Allyn will not be responsible for loss associated with the use of any Welch Allyn product that 1 has had the serial number defaced 2 has been repaired by anyone other than an authorized Welch Allyn Service Representative 3 has been altered or 4 has been used in a manner other than in accordance with the instructions Service Information For Technical Support or to obtain return instructions please contact the nearest Welch Allyn service center listed below USA Customers Canada Customers Phone 815 685 4560 Phone 905 890 0004 or 800 535 6663 North America only Jor 1 800 561 8797 North America only Fax 315 685 3361 Fax 905 890 0008 INTERNATIONAL Customers Welch Allyn Germany Welch Allyn Australia Latin America Tel 49 7477 927 170 Tel 61 2 9638 3000 Tel 305 669 9003 Fax 49 7477 927 170 Fax 61 2 9638 3500 Fax 305 669 8951 Welch Allyn Ltd Singapore Welch Allyn UK Ltd Welch Allyn China Tel 65 6291 0882 CublingtonRoad Tel 86 21 6327 9631 Fax 65 6291 5780
8. ical IEC 61000 4 4 1kV I Os oO commercial or hospital environment Surge 1kV Differential 2kV Mains power quality should be that of a typical IEC 61000 4 5 2kV Common 2kV commerical or hospital environment Voltage Dips Dropout gt 95 Dip for 0 5 Cycle gt 95 Dip for 0 5 Cycle Mains power quality should be that of a typical IEC 61000 4 11 commerical or hospital environment 60 Dip for 5 Cycles 60 Dip for 5 Cycles 30 Dip for 25 Cycles 30 Dip for 25 Cycles gt 95 Dip for 5 Seconds gt 95 Dip for 5 Seconds Power Frequency Power frequency magnetic fields should be that 50 60Hz of a typical commerical or hospital environment Magnetic Field IEC 61000 4 8 Guidance and Manufacturer s Declaration Immunity The REF 49000 is intended for use in the electromagnetic environment specified below The customer or user of the REF 49000 should ensure that it is used in such an environment Immunity Test TestLevel evel Electromagnetic Environment Guidance ea Portable and mobile communications equipment should be separated from the REF 49000 by ie eee than the distances calculated listed below Conducted RF 3 Vrms 10 Vrms P 9 39 Sart P IEC 61000 4 6 ies Fhe 10 Vrms D 1 2 Sart P 10Vrms In D P Radiated RF_ ISM Bands 10 Vim 2 082 Sart P IEC 61000 4 3 150 kHz to 80 to 800 MHz SOMHz Where P is the max power In watts and D is the recommended separation distance in meters 30 Ae 5 Field strengths from fixed tr
9. not operate the light until the light is thoroughly dry gt Do not sterilize the unit CAUTION Do not immerse in cleaning solutions Battery Replacement Direct Plug In Transformer 1 Plug Power cord trom the Solid State Procedure Headlight into the Direct Plug In Power cord Push until firmly in place Gently screw the external connector sleeve clockwise to secure The instrument is now ready for use Plug direct power source Into a nearby receptacle a w Troubleshooting Trouble Area Possible Cause Corrective Action Verify that the unit operates on direct power source If yes insure that the battery is connected properly refer to the battery replacement section for No Light Output Dead battery or battery not instructions on connecting the battery If the battery is connected properly connected properly recharge or replace battery Low Light Output Low charge on battery Verify that the unit operates on direct power source If yes recharge or replace battery Specifications Electrical Ref Output Model input vonage Voltage 49020 120VAC 50 60 Hz lt 10 uA 49022 230VAC 50 60 Hz lt 10 uA 49024 230VAC 50 60 Hz lt 10 uA 49026 240VAC 50 60 Fz Emissions and Immunity Information Guidance and Manufacturer s Declaration Emissions The REF 49000 is intended for use in the electromagnetic environment specified below The customer or user of the REF 49000 should ensure that It is used in such an
10. right light sources and their reflections and protect eyes where normal pupil sizes and aversion responses are not present Introduction Thank you for purchasing the Solid State Portable Headlight by Welch Allyn the worldwide leader in illuminated medical diagnostic instrumentation By following the use and care guidelines supplied in this owner s manual you will enjoy years of dependable trouble free service from your new headlight This headlight is designed to meet the various needs of a physicians office hospital environment and specialist s office Components Standard Parts List Solid State Procedure Headlight with Direct Power Supply Model 49020 Domestic Model 49022 European Model 49024 U K Model 49026 Australia Replacement Parts List When ordering replacement parts for your Solid State Procedure Headlight please use the following numbers Model 74180 Charger Domestic Model 74182 Charger European Model 74184 Charger U K Model 72250 Replacement Battery Model 74186 Charger Australia Model 75270 Direct Power Supply Domestic Model 75272 Direct Power Supply European Model 75274 Direct Power Supply U K Model 75276 Direct Power Supply Australia Accessory Parts List Model 75260 Battery Pack with Charger Domestic Model 49000 Procedure Headlight i Model 75262 Battery Pack with Model 49099 Carrying Case 3 Charger European Model 72250 Rechargeable Battery Model 75264 Batter
11. y Pack with Charger U K Model 75266 Battery Pack with Charger Australia Set up and Operation Instructions for Use The Solid State Procedure Headlight REF 49020 consisting of Procedure Headlight REF 49000 with Direct Power Source REF 75270 and Accessory Portable Power Source Charger REF 75260 The Solid State Procedure Headlight is designed to operate off the direct or the portable power source To operate the headlight using the direct power source follow the instructions and illustrations in the section labeled Direct Plug In Transformer Simply turn on the on off switch located on the Direct Plug to operate the headlight To operate the headlight using the portable power source follow the instructions and illustrations under the section labeled Connecting Headlight to Portabble Power Source To recharge the portable power source follow the instructions and illustrations in the Recharging the Portable Power source section To adjust the light spot size turn the knob on the front section of the luminaire To adjust the headband simply rotate the adjustment knob located on the back of the headband Use the Solid State Procedure Headlight to provide illumination while performing a number of activities in the physician s office hospital or emergency environment such as minor surgery general exam foreign body removal OB GYN applications procedures dermatology examinations or any procedure which requires a small homog
Download Pdf Manuals
Related Search