OmniView Secure DVI Dual
Contents
1. determines in its sole discretion that it is impractical to ship the damaged equipment to Belkin Belkin may designate in its sole discretion an equipment repair facility to inspect and estimate the cost to repair such equipment The cost if any of shipping the equipment to and from such repair facility and of such estimate shall be borne solely by the purchaser Damaged equipment must remain available for inspection until the claim is finalized Whenever claims are settled Belkin reserves the right to be subrogated under any existing insurance policies the purchaser may have How state law relates to the warranty THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN THERE ARE NO OTHER WARRANTIES EXPRESSED OR EXCEPT AS REQUIRED BY LAW IMPLIED INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND SUCH IMPLIED WARRANTIES IF ANY ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL SPECIAL DIRECT INDIRECT CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS BUT NOT LIMITED TO LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES This warranty gives you specific legal rights and you may also have other rights which may vary from state2. 2 Using the Belkin DVI USB KVM Cable Kit F1D9201 XX connect the male DVI connector to the monitor port on your computer Then connect the other end of the cable into an available port on the Switch Refer to diagram below 3 3 Using the Cable Kit connect the USB Type A connector to an available USB port on your computer Then connect the USB Type B connector to the corresponding USB port on the Switch Refer to diagram below 3 4 Connect the two audio cables audio and microphone to your computer Then connect the other end to the corresponding audio and microphone port on the Switch 3 5 Repeat the steps above for each additional USB computer you wish to connect Note The Cable Kit must be connected directly to a free USB port on your computer with no USB hubs or other devices in between UOI I9S 12 Step 4 Powering Up the Systems required 4 1 Power on the attached monitor 4 2 Attach the power adapter to the DC power jack labeled 5V 3A on the back of the Switch Only use the power adapter supplied with the Switch Refer to diagram below User Console 4 coo 6 mmo usa D 4 3 Power on your computers All computers can be powered on simultaneously Note Your computers should recognize the Switch and automatically install the HID USB driver if necessary When you power on your computers the Switch emulates both a mouse and keyboard on each port and allows your
3. F1DN102D 2 5 Ibs 1 1kg F1DN104D 2 5 Ibs 1 1kg zu zn Made in the USA of imported parts The Switch includes a 5 volt 3 Amp power adapter Installation Before you begin please take a few minutes to register your product This may assist Belkin in contacting you regarding important information regarding secure use of your product You may register your product online by going to https www belkin com registration Pre Configuration Where to place the Switch The enclosure of the Switch is designed for desktop or rack mount configuration An optional Rack Mount Kit Belkin part number F1D005 is available for use with the 2 and 4 Port Switches Consider the following when deciding where to place the Switch your proximity to the port selectors on the front of the Switch the lengths of the cables attached to your keyboard monitor and mouse the location of your computers in relation to your console the lengths of the cables you use to connect your computers to the Switch Warning Avoid placing cables near fluorescent lights air conditioning equipment or machines that create electrical noise e g vacuum cleaners Installation Step 1 Mounting the Switch optional Bracket Installation FIDN102D and F1DN104D The 2 and 4 Port Switches can be installed into a 19 inch rack using an optional Rack Mount Kit sold separately Belkin part number F1D005 1 1 Attach the Rack Moun
4. this declaration relates Have been tested and found compliant with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation These limits are designed to provide reasonable protection against harmful interference in a commercial industrial installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressiy approved by the party responsible for compliance could void the user s authority to operate this equipment ICES This Class A digital apparatus co
5. BELKIN me User Manual F1DN102D F1DN104D Table of Contents Wis Introd ction 1 iid EIE eie 1 Package Contents eret tre nass 1 2 OVerViewW En En nde decreed a ceo 2 Security Features een tape RUD E nee een 2 Other Feat rBs eese rris tere Daniela sper ta armen er 3 Equipment Requirements cccceeeceeecee eee eee eee sansa eee ese eaeen eee eaeenees 4 System Requirements eese teen entente nnne nni 5 Unit Display Diagrams rper t hbro eh rene aaben 6 SPCCITI CATIONS mST 7 Se NStallatiO Mm EPPPRPRBSBEFAFEFEPE ABEFBFFPREFESEREELPESFERSEEB RRTERFREFERFEFEFEFENPEREEEFPERFEREFEHRSTERER 8 Pre Configuration nee nes nn 8 Mounting the Switch optional ussusssensennennennnnnnnnnnnnnnnnnnen nenn 9 Connecting the Console to the Switch uussenseessnnennnnnnnnnnnnnnnn 10 Connecting Computers to the Switch u zuussnsenennsnnnnnnnnnnnnnnnnn 11 Powering Up the Systems ssssssssssese Heer 12 LMUFIDPATIUSQUdIMME 13 Selecting a Computer Using Port Selectors eeeeesess 13 5 Frequently Asked Questions ccccccccceeeesseeeeeeeeeeeeeeeeeneneeeeeeeeeeeeeeeeeeees 14 6 TROUBLESHOOT Gis ccc cccctcsconsssdheecisesvacnceconaddiveceduesectesecuaterextssencedncssaisriee 16 7 Information eode eee il 18 Introduction Congratulations and thank you for purchasing this Belkin Omni
6. Support The Switch supports video resolutions of up to 2560x1600 This includes support for digital displays 20 inches and larger Audio Switching Allows you to share speakers and microphone between computers Dedicated Port Selectors Port selectors located conveniently on the front panel of the Switch allow you to switch easily from one computer to the next Each button controls a single computer port LED Indicators An LED above each port selector illuminates to indicate that the console currently controls the corresponding computer As a port selector is pushed the LED above it will illuminate Metal Enclosure The Switch features a rugged metal enclosure that provides stability and allows the Switch to be placed beneath your monitor or other desk item Desktop or Rack Mount Installation With its compact design the Switch can be placed on your desktop or mounted to a standard 19 inch server rack for 1U installation Global Power Adapter The Switch includes a global power adapter and interchangeable plugs to allow for both domestic and international installations The 2 and 4 Port Switches require an optional Rack Mount Kit for rack installation Belkin part number F1D005 Includes AC plugs for the U S U K Europe and Australia Overview Security Features Dedicated Processors Designed specifically for secure environments the Switch features a dedicated processor per computer port This keeps each com
7. View Secure DVI Dual Link KVM Switch the Switch Designed especially for secure military and government installations the Switch provides the centralized control required by today s IA Information Assurance computer environments It allows users to manage multiple computers from a single USB console while preventing unintended data transfer between computers running on different security levels This User Manual provides all the details you ll need to install and operate your new Switch in addition to expert troubleshooting advice in the unlikely event of a problem For quick and easy installation please refer to the Quick Installation Guide included in your packaging Package Contents OmniView Secure 5V DC 3A Global 4 Interchangeable DVI Dual Link Power Adapter AC Plugs KVM Switch User Manual Quick Installation Guide Includes AC plugs for the U S U K Europe and Australia Important Tamper evident seals have been placed on both sides of the Switch enclosure to provide evidence if the product has been opened and potentially compromised see diagram on page 6 If either seal has been removed or appears disrupted please call Belkin Technical Support at 800 282 2355 EH UuoI1298S s e o lo Overview Other Features USB Support The Switch is compatible with USB 1 1 and USB 2 0 technology and supports Plug and Play connectivity with USB computers keyboards and mice Dual Link DVI
8. computer The Switch also prevents any data transfer between connected computers ensuring the security of your computers Please note that the default port at power up is port one In case of a power failure or if the power is cycled the Switch will default to port one Note It may take longer for your mouse and keyboard to re synchronize when the computer is recovering or initializing from Standby Hibernate or Sleep modes e a EN UuoI128S 14 Frequently Asked Questions What does NIAP Common Criteria validation to EAL 4 mean To learn more about NIAP Common Criteria and EAL 4 visit http www niap ccevs org cc scheme consumer guidance cfm What do I do if I find that the tamper evident seals on the Switch have been removed or disrupted Please call Belkin Secure KVM Support at 800 282 2355 immediately The KVM Switch s circuitry may have been compromised Where can I register my Switch You can register your Switch on the Web by directing your browser to https www belkin com registration Where can I go to report a product issue You may call Belkin Secure KVM Support at 800 282 2355 or direct your web browser to http www belkin com support contact email technicalsupport How does the Switch allow the user to switch between computers The Switch only supports one method of port selection The user can access the desired computer by pushing the associated port selector How fa
9. computers to boot normally The computer connected to port 1 will be displayed on the monitor Check to see that the keyboard monitor and mouse are working normally Proceed to do this with all occupied ports to verify that all computers are connected and responding correctly If you encounter an error check your cable connections for that computer and reboot If the problem persists please refer to the Troubleshooting section in this User Manual Using your Switch Selecting a Computer Using Port Selectors Now that you have connected your console and computers to the Switch it is ready for use You can select which computer you wish to control by pressing the corresponding port selector on the front of the Switch The LED will illuminate to indicate which computer or port is currently selected It takes approximately 1 2 seconds for the video signal to refresh after switching computers Re synchronization of the mouse and keyboard signals also occurs This is normal operation and ensures that proper synchronization is established between the console and the connected computers Once you press a port selector the Switch immediately disables the connection between your console and the previously selected computer and establishes a new connection between your console and the new computer selected Keyboard and mouse inputs can only be sent to the selected computer and video outputs can only be received from the selected
10. esh rate setting on your computer Lower the video resolution of your monitor Check that the video cable length does not exceed 15 feet 4 6m Check that the graphics card you are using supports the resolution and refresh rate setting on your computer Connect the monitor directly into the computer you are having trouble with to see if the problem still appears am getting a black screen on my monitor Check that all video cables are inserted properly Check that there is proper voltage available to the power adapter and that it is inserted correctly Connect your monitor directly to the computer to verify that your monitor is functioning properly Reboot the computer i e Ey uoI1298Ss 16 Troubleshooting Keyboard The computer does not detect my keyboard or my keyboard does not work when I switch computers or reboot Check that the keyboard you are using is connected properly to the Switch Check that the USB cable between the Switch and the computer is firmly connected Try connecting to a different USB port on the computer Make sure the keyboard works when directly plugged into the computer the HID USB driver is installed on the computer Rebooting may be necessary when trying this f you are using keyboard software that was included with your keyboard uninstall it and then reinstall f the computer is coming out of standby mode allow up to one minute
11. mplies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada CE Declaration of Conformity We Belkin International Inc declare under our sole responsibility that the products F1DN102D F1DN104D to which this declaration relates are in conformity with Emissions Standard EN55022 and with Immunity Standard EN55024 LVP EN61000 3 2 and EN61000 3 3 Belkin International Inc Limited 3 Year Product Warranty What this warranty covers Belkin International Inc Belkin warrants to the original purchaser of this Belkin product that the product shall be free of defects in design assembly material or workmanship What the period of coverage is Belkin warrants the Belkin product for three years Information What will we do to correct problems Product Warranty Belkin will repair or replace at its option any defective product free of charge except for shipping charges for the product Belkin reserves the right to discontinue any of its products without notice and disclaims any limited warranty to repair or replace any such discontinued products In the event that Belkin is unable to repair or replace the product for example because it has been discontinued Belkin will offer either a refund or a credit toward the purchase of another product from Belkin com in an amount equal to the purchase price of the product as evidenced on the original purchase receipt as discoun
12. nd audio video transmission One Cable Kit is required per connected computer F1D9201 XX J Belkin DVI USB KVM Cable Kits with Audio amp Mic F1D9201 06 6 ft 1 8m F1D9201 10 10 ft 3m F1D9201 15 15 ft 4 6m F2E0271 SD DVI I to DVI D Adapter Note Due to USB and DVI limitations the cable length cannot exceed 15 feet 4 6m System Requirements Operating System 0S Platforms The Switch is compatible with computers running on but not limited to the following OS platforms Windows 2000 Windows XP Home Professional Windows 2003 Server Windows Vista Linux Red Hat Enterprise Linux WS Mac OS X v10 3 and higher Keyboards USB compatible including wireless keyboards Mice USB compatible including wireless or optical mice Monitors Digital displays with DVI D support single link and dual link Speakers Computer speakers with 3 5mm stereo plug Microphone Computer microphone with 3 5mm plug Overview Unit Display Diagrams Front View LED Indicators aD 02 03 94 Port Selectors Back View Console Audio Mic Input Jacks Computer DVI USB Console USB Keyboard Port u and Audio Mic Ports Console USB Mouse Port Console DVI Monitor Port Side View DC Power Jack Tamper Evident Seals F1DN104D model shown IMPORTANT NOTICE There should be one tamper evident seal on each side of the S
13. puter running on different security levels completely separated and secure at all times and prevents any unintended data transfer between computers No Memory Buffer The Switch does not have a memory buffer and does not have the ability to store data This prevents any keystrokes or other data input from being unintentionally transferred as you switch between computers ensuring the integrity of your data The Switch does not include any features that require memory such as hot keys AutoScan or an on screen display OSD Non Reprogrammable Firmware The Switch features custom firmware that is not reprogrammable preventing the ability to tamper with the KVM logic Tamper Evident Seals Tamper evident seals are placed on both sides of the enclosure to provide indication if the Switch has been opened or compromised Tamper Proof Hardware All integrated circuits are soldered directly to the printed circuit board to prevent tampering with the components NIAP Listing The Switch is listed by the National Information Assurance Partnership NIAP It is NIAP Common Criteria validated to EAL 4 Evaluation Assurance Level 4 augmented with ALC FLR 3 Is je a gt o IN UOIY I9S Equipment Requirements Cables Belkin highly recommends you use Belkin DVI USB KVM Cable Kits with Audio amp Mic for your Switch to help ensure superior performance These cables offer the highest quality possible to ensure optimal data a
14. r can the Switch be from my computer The Switch can be located up to 15 feet 4 6m away from your computer due to DVI and USB cable limitations Do have to install software to use the Switch No the Switch does not require any software to be installed on your computers Can I use the Switch with a computer that does not support USB No the Switch only works with USB capable computers Does the Switch require an AC adapter Yes the Switch requires a 5 volt DC 3 Amp minimum power adapter in order to function properly Frequently Asked Questions Does the Switch support Linux Yes the Switch works with Red Hat Linux and some Linux operating systems configured for USB support Does the Switch support Microsoft IntelliMouse The Switch supports mice from Belkin Microsoft Logitech Kensington and many other manufacturers Please contact Belkin Technical Support at 800 282 2355 for any compatibility issues you may experience General My computer does not boot when connected to the Switch but works fine when I connect my keyboard video and mouse directly to my computer Make sure that the DVI USB KVM Cable Kit is connected firmly between the Switch and the computer Video am getting ghosting shadowing or fuzzy images on my monitor Check that all video cables are inserted properly to the Switch computer and monitor Check that the monitor you are using supports the resolution and refr
15. t Bracket to the Switch using the Phillips screws provided Refer to diagram below Your Switch is now mounted securely to the rack and you are ready to connect your console Is ola s Kis UO0I D9S Step 2 Connecting the Console to the Switch required Warning Before attempting to connect anything to the Switch or your computers please ensure that all computer equipment and devices are powered off Plugging and unplugging cables while computers are powered on may cause irreversible damage to the computers and or the Switch Belkin International Inc is not responsible for damage caused by your failure to do so Before you connect your console to the Switch make sure that your USB keyboard and mouse work properly with all your computers the Human Interface Device HID USB drivers are installed on all computers 2 1 Connect your monitor DVI cable to the DVI port on the back of the Switch in the User Console section Refer to diagram below 2 2 Connect your keyboard and mouse USB cables to the USB keyboard and mouse ports on the back of the Switch in the User Console section Refer to diagram below 2 3 Connect your speaker and microphone cables into the corresponding ports in the User Console section Installation Step 3 Connecting Computers to the Switch required 3 1 Make sure all computers and the Switch are powered off 3
16. ted by its natural use What is not covered by this warranty All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkin s request at the sole expense of the purchaser or if Belkin determines that the Belkin product has been improperly installed altered in any way or tampered with The Belkin Product Warranty does not protect against acts of God such as flood lightning earthquake war vandalism theft normal use wear and tear erosion depletion obsolescence abuse damage due to low voltage disturbances i e brownouts or sags non authorized program or system equipment modification or alteration How to get service To get service for your Belkin product you must take the following steps 1 Contact Belkin International Inc 12045 E Waterfront Drive Playa Vista CA 90094 Attn Customer Service or call 800 223 5546 within 15 days of the Occurrence Be prepared to provide the following information a The part number of the Belkin product b Where you purchased the product c When you purchased the product d Copy of original receipt 2 Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim Belkin reserves the right to review the damaged Belkin product All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser If Belkin
17. to regain keyboard function Try a different keyboard Some of the keys on my keyboard are not functioning properly when I use a Mac computer f you are using a PC keyboard on a Mac system a few of the option keys on your PC keyboard may be reversed All major keys will function as labeled Troubleshooting Mouse The computer does not detect my mouse or my mouse does not work when I switch computers or reboot Check that the mouse you are using is connected properly to the Switch Check that the USB cable between the Switch and the computer is completely connected Try connecting to a different USB port on the computer Make sure the mouse works when directly plugged into the computer the HID USB driver is installed on the computer Rebooting may be necessary when trying this f you are using a mouse driver that was included with your mouse uninstall it and install the standard Microsoft mouse driver f the computer is coming out of standby mode allow up to one minute to regain mouse function Try a different mouse ENS S on uoI12es 18 Information Federal Communication Commission Interference Statement Subpart A FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We Belkin International Inc of 12045 E Waterfront Drive Playa Vista CA 90094 declare under our sole responsibility that the products FIDN102D F1DN104D to which
18. to state Some states do not allow the exclusion or limitation of incidental consequential or other damages so the above limitations may not apply to you Bo 2 e n 19 UOIY I9S BELKIN belkin com Belkin Tech Support US http www belkin com support UK http www belkin com uk support Australia http www belkin com au support New Zealand http www belkin com au support Europe http www belkin com uk support 2011 Belkin International Inc All rights reserved All trade names are registered trademarks of respective manufacturers listed Windows Windows Vista Microsoft and IntelliMouse are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Mac OS and Mac are trademarks of Apple Inc registered in the U S and other countries PM00507 Rev A01
19. witch enclosure total of two seals If both seals are visible and do not appear to be disrupted your Switch has not been opened or compromised since time of production If for any reason one of the seals is missing or appears disrupted please call Belkin Technical Support at 800 282 2355 Specifications Part No F1DN102D FIDN104D Enclosure Metal enclosure with high impact plastic faceplate Power Requirements 5V DC 3A minimum power adapter with center pin positive polarity D AC Input 100 to 240VAC Interchangeable AC Plugs 4 U S U K Europe Australia A No of Users Supported 1 No of Computers Supported 2 and 4 respectively for 2 and 4 port models Monitors Supported Single Link and Dual Link digital DVI D displays Resolution Support Up to 2560x1600 Console Keyboard Input USB Type A Console Mouse Input USB Type A Console Monitor Port DVI Dual Link female Console Speaker Mic 3 5mm female CPU Keyboard Mouse Ports USB Type B CPU Audio Mic 3 5mm female CPU Monitor Ports DVI Dual Link female Port Selectors 2 and 4 respectively for 2 and 4 port models LED Indicators 2 and 4 respectively for 2 and 4 port models Operating Temp 32 to 104 F 0 to 40 C Storage Temp 4 to 140 F 20 to 60 C Humidity 0 80 RH non condensing Warranty 3 years Dimensions F1DN102D 11 x 1 75 x 6 in 279 x 45 x 150mm F1DN104D 11 x 1 75 x 6 in 279 x 45 x 150mm Weight
Download Pdf Manuals
Related Search