Home

Untitled

1. Projector 1 Projector 2 Projector 3 Starting address 1 Starting address 5 Starting address 9 Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal If you are using the standard controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other DMX outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the DMX CONTROL 24 with the DMX input of the nearest projector Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 ohms resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 3 Fixture addressing Projector addressing Please note that the DMX CONTROL 24 assigns the DMX starting addresses every 6 steps You have to address every projector to the respective starting address Otherwise the channel assignment will not be correct All projectors with the same starting address work synchronically
2. Projector Starting address Projector Starting address Projector 1 1 Projector 3 13 Projector 2 7 Projector 4 19 4 4 Connection to the mains Connect the fixture to the mains with the power plug The occupation of the connection cables is as follows Cable EU capies Fin ternational L Brown Live Light blue Neutral Yellow Green Earth The earth has to be connected 5 Operation Select the projectors With the DMX CONTROL 24 you can either control the DJ Scan 150 XT DJ Scan 250 XT or Spot 150 XT Spot 160 XT The standard setting of the controller is DJ Scan 150 XT A If you wish to switch the controller to the DJ Scan 250 XT B or Spot 150 XT Spot 160 XT C see instructions below Press and hold the Program Up Down buttons Plug the power plug in The Program Display and the Blackout LED are flashing and the Program Display shows the current selection A Press one of the Program Up Down buttons and adjust the selection B or C Confirm your selection via the Blackout key Calling up a pre programmed program Select the desired program between 1 9 C r via the Program Up Down keys The selection C means that all programs 1 9 will be run through The selection r means that the programs will be randomly selected Press the Blackout key in order to project the program LED off Adjusting the program speed The programs run through the selected program step b
3. DMX Control 24 USER MANUAL show lighting 9 DMX CONTROL 24 Table of contents 1 Salely instructions Sii adds 2 Operating determinations u nn dd ek wi Go ed Ta 3 Description of the device issie sd Ee UR inicia A Installation ia ENSUCIA Re er Ge Ge EG EG 4 2 DMX 512 connection with the Projectors ee ee ee ee Re ee ee ee ee ee ee 4 3 Fixture addressing si ae Ee ia 44 Connection TO ME MASS ee a aa erledige 5 Operation EE EE N raare EEan En 6 TechriiealspeellieatiorHE scannen 7 Cleaning and maintenance uussunssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 8 AppenAdDE ase EE Ee Ee ee ei en Ee ee waa CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FORYOUR OWN SAFETY PLEASE READTHIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START UP 1 Safety instructions Every person involved with installation and maintenance of this device have to be qualilfied follow the instructions of this manual CAUTION Be careful with your operations With a high voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Important The manufacturer will no
4. d up Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture 4 or dust There should not be any cables lying around You endanger your own and the safety of others Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit electric shock etc 3 Description of the device DS SS LANE ODI ZA EDESA ZE EER AAA BEF OLMEVE gt Ly AZ ESE A SSS Ss 0 Mario 1 Top panel 2 Audio input 3 DMX output 4 Power supply socket Top panel 13 l 9 DMX Control l 10 O o O Program Spee 11 Musi E Spee EO Oo ER 12 19 Fast ES pa O Strobe O O O an O A series Blackout 14 15 5 AUTOTRIG KEY If the LED shines the controller is in Auto mode n
5. e and service operations are only to be carried out by authorized dealers Should you need any spare parts please use genuine parts If the power supply cable of this device will be damaged it has to be replaced by authorized dealers only in order to avoid hazards 8 Appendix We believe you will enjoy your DMX CONTROL 24 We assure you will enjoy this product for years if you follow the instructions given in this manual If you have any questions and comments please do not hesitate to contact us Version 1 0
6. ormal operation without sound control 6 MUSIC TRIG KEY If this LED shines the controller is in Audio mode operation with sound control 7 MANUALTRIG KEY With the Manual Trig key you can jump from one step to another 8 STROBE KEY By pressing the Strobe key all channels are being strobed 9 SLOW SPEED KEY For adjusting the program to slow movement 10 MEDIUM SPEED KEY For adjusting the program to medium movement 11 FAST SPEED KEY For adjusting the program to fast movement 12 RANDOM SPEED KEY For adjusting the program to random movement 13 PROGRAM DISPLAY 14 BLACKOUT KEY The Blackout function closes the light output of all connected projectors via the shutter Caution The Blackout key has to be pressed LED is off as soon as a program is called up Otherwise there will not be any light output 15 PROGRAM UP DOWN KEYS 4 Installation 4 1 Sound control The sound control either works via the Va mono jack socket or the built in microphone If the DMX CONTROL 24 is supposed to work via a sound signal at the Audio In socket connect the 1 4 jack socket with the soundsignal of your headphones output or a second adjustable output if existing of your mixer or with the loud speaker output of your amplifier Tip Data Sleeve Ground Caution Never connect the sound input with the DMX output as this will destroy the electric DMX driver 4 2 DMX 512 connection with the projectors
7. t accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Always plug in the power plug least The power plug has to be accessable after installing the device Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth The electric connection repairs and servicing must be carried out by a qualified employee 2 Operating determinations This device was designed for indoor use only If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature When taking the device into operation please make sure that the housing is closed firmly with all the necessary screws tightene
8. y step with the programmed speed You can adjust the program speed via the Slow Speed button Medium Speed button or Fast Speed button Jump from one step to another Via the Manual Trig key you have the possibility to jump from one step to another If a program is run and the Manual Trig key is pressed the projector jumps to the next step after finishing the current step The Manual Trig LED shines and the program is stopped If you wish to start the program once more press the Auto Trig key or the Music Trig key Activating the sound control If the sound control is activated the program moves in the bass tact of the music Press the Music Trig key LED shines and the sound control is activated Strobe function Via the Strobe key you can strobe all channels at the same time 6 Technical specifications Power supply 100 125V 200 230V AC 50 60Hz Power consumption 4W Number of control channels 24 Sound control either via Va Jack or built in microphone Sound input Ya mono Jack Audio sensitivity 0 3 1V DMX 512 output 3 pin XLR connector Pre programed programs 9 Dimensions LxWxH 155 x 110 x 80 mm Weight 0 5 kg 7 Cleaning and maintenance DANGER Disconnect from the mains before starting any maintenance work We recommend a frequent cleaning of the device Please use a soft lint free and moistened cloth Never use alcohol or solvents There are no servicable parts inside the device Maintenanc

Untitled

Contents

Download Pdf Manuals

Related Search

Related Contents