BJ192e-3X4 Multi-Power Meter User Manual Version
Contents
1. actions are essential high qualified operators must perform them Before any adjustment replacement maintenance or repairing operation is carried out the instrument must be disconnected from any power supply source When any protection failure is suspected to exist the instrument must be immediately put our of service The instrument s design allows a quick replacement in case of any failure 6 TECHNICAL SERVICE For any inquiry about the instrument performance or whether any failure happens contact to Blue Jay s technical service Blue Jay After sales service Redstone Road 2 17 3 Jiangbei District 400020 Chongqing Tel 0086 023 67636974 Fax 0086 023 67636974 E mail tech cqbluejay com2. BJ192e 3X4 Multi Power Meter User Manual Version 1 2 Please read carefully before using this user manual Please save this document 1 SPECIFICATIONS Input Voltage Rated 400V optional 100V Current Rated 20A directly connection Frequency 45 65Hz Load Voltage lt 0 5VA phase rated 220V Current lt 0 5VA phase rated 20A Overload Current 1 2 times rated continuous 10 seconds for 10 times the rated Voltage 1 2 times the rated continuous 10 seconds for 800V Dielectric strength IEC 688 IEC 255 3 1989 2kV AC RMS 1 minute between input output case power supply EMC Test standard Test voltage Electrostatic discharge immunity IEC 61000 4 2 BKy test level 4 Electrical fast transient burst ESS TNO level 3 Input 1kV Power supply 2kV immunity test IEC61000 4 5 Surge Shock immunity test uaa common mode test voltage 4kV Work environment Temperature 20 C 60 C Humidity RH 20 95 No condensation Protection Panel IP40 Storage Conditions Temperature 25 C 70 C Humidity RH 20 95 Working Power AC 85 265VAC DC 45 65Hz Maximum power consumption 6W Dimensions L x W x H 72mmx72mmx123mm Installation hole size L x W 66 0 8mm x 66 0 8mm 2 INSTALLATION AND START UP The manual you hold in your hand contains information and warnings that the user should respect in order to guarantee a proper operation of
3. Power Supply 58 59 60 46 47 48 49 4 5 6 7 8 9 11121314 ji Bil ji 0 o i S1 S2 A pm Po j B a S1 S2 C Pi Mm P2 IMPORTANT REMARK If power 0 01 is shown for any of the phases and voltage and current are not zero for this phase check out following points Assure that A B C phases coincide in voltage and current Correct polarity Reverse the current transformer placed at this phase 2 3 Mounting BJ 192e 3X4 is for panel mounting controller is to be mounted on panel cut out 66 0 5 x 66 0 5 mm All connections keep inside the cabinet Notes 1 The controller must not be power on until this is completely installed 2 Panels shall not exceed 12 mm maximum thickness If more than this range please consider using the rail mounting 3 OPERATION MODE The instrument has three line displays Each one has also two LED type indicators red colour Every led will be on according to the parameter presently shown in screen When the 192e 3X4 is powered up all the LED indicator will on and meter start self test after some seconds the meter is ready for operation and shows one of the available screens Press this key the meter will show the measured data in different screen the change turn is U V I lo h When show the data the LED indicator will on and show the related parameter Press this key the meter will change the measurement data in the insta
4. all the instrument functions and keep its safety conditions The instrument must not be powered on and used until its definitive assembly on the cabinet s door If the instrument is not used as manufacturer s specifications the protection of the instrument will be damaged When any protection failure is suspected to exist for example it presents external visible damages the instrument must be immediately powered off In this case contact a qualified service representative 2 1 Installation Mounting Instrument is to be mounted on panel cut out 66 0 8 x 66 0 8 mm All connections keep inside the cabinet Note that with the instrument powered on the terminals could be dangerous to touching and cover opening actions or elements removal may allow accessing dangerous parts Therefore the instrument must not be used until this is completely installed Notes Input signal BJ192e using a separate acquisition calculate for each measurement channel to ensure consistent in use for different load forms its a variety of connection mode A Voltage input Input voltage should not exceed the rated input voltage products 100V or 400V Otherwise should use external CT the input voltage to be installed in the 1A fuse B Current Input Standard input current is 20A if greater than 20A should use external CT Even if you are using on the CT are connecting with other instruments wiring methods should be used in series Before
5. ntaneous value average value and maximum value as the current shown data Press this key can reset the maximum value and average value to zero The SETUP procedure of the BJ192e X is performed by means of several SETUP options Once into the SETUP use the keyboard to select different options and enter required variables 1 Password enter 2 Input signal selection 3 Communication preferences o Code Codd o Haft A Set network 7999 Ooo C1 faa one Set Input LiaPr Set current Cani range lt Set voltage 2 el range port QD Set PT ratio InP in PE gt var Ca y Set CT ratio dam Lo Canal Set slave n gone Sa address Set communication me gna Conn anal Set baud bAUd bAUd bAUd bAUd BAUd fate 608 H320 BASDI Conn Set data fou i fomat 4 SAFETY CONSIDERATIONS All installation specification described at the previous chapters named INSTALLATION AND STARTUP OPERATION MODE and SPECIFICATIONS Note that with the instrument powered on the terminals could be dangerous to touching and cover opening actions or elements removal may allow accessing dangerous parts This instrument is actory shipped at proper operation condition 5 MAINTENANCE The 192e 3X4 does not require any special maintenance No adjustment maintenance or repairing action should be done when the instrument open and powered on should those
6. remove the current input connection must be sure to disconnect the primary circuit or shorted secondary circuit of CT Suggest using the terminal block please not directly connect to CT in order to facilitate disassembly Auxiliary power BJ192e 3X4 Multifunction Power Meter with universal AC DC power input if not for a special statement we provide the 220VAC DC or 110VAC DC power interface for standard products Instruments limit work power supply AC DC 85 265V please ensure that the auxiliary power can match for BJ192E series meter to prevent damage to the product A Suggest install 1A fuse in the fire line side B For the areas with poor power quality suggest install lightning surge suppressor and rapid burst suppressor to prevent lightning strikes 2 2 Connection terminal see label on the rear part N O Oa ADNa 12 Voltage B phase input 13 Voltage C phase input 14 Neutral Voltage input 58 RS 485 59 RS 485 60 RS 485 GND Current A phase S1 input Current A phase S2 input Current B phase S1 input Current B phase S2 input Current C phase S1 input 9 11 Voltage A phase input Supply voltage input 0 V Power Supply Supply voltage input 220 Va c a a a 60 46 47 18 43 Current C phase S2 input g 11 T2 13 14 E a ae EDIL IELI iii cs oO WwW gt Three phase network 3 wires low voltage
Download Pdf Manuals
Related Search