MS-SW5 - User`s manual
Contents
1. The Alyseum MS SWS5 is a 5 ports switch in Eurorack format The switch uses an industrial chipset assure hi pass thru performance and reliable operations oo e o o o o o o oe gt Se N Features UnManaged 5 ports switch in Eurorack format Plug and play no configuration required Build in Industrial Chipset for the better performance 1 0Gbps high performance memory bandwidth Direct Eurorack power supply interfacing without adapter 100 Base T Ethernet interface with shielded RJ 45 Auto MDIX allows using straight trough or cross over UTP cable Panel wide 5 HP Specifications Front Panel width 25 4 mm 5 HP Module Depth 55 mm RJ 45 shielded Power requirement 5 Volts regulated 320 mA with 5 active ports Page 3 MS SW5 Users manual Revision 1 1 4 1 Package content e 1MS SW5 module with Eurorack compliant front panel and power supply connector e 1 plastic bag containing o 2 x M3 screws o 2 x M3 nylon washers e Warranty amp user s manual access card 4 2 Accessories CAT5e cable 0 5 meter CAT5e cable 1 meter CAT5e cable 3 meters CAT5e cable 10 meters http www alyseum com accessories 4 3 Installing the MS SW5 into the A 100 rack The module MS SW5 need solely a power supply of 5 Volts make sure that your backplane provided well this voltage and with sufficient current If no install a converter from 12 Volts to 5 Volts DC no linear regulator only switching converte2. e ts preferable to connect your computer on the port 1 the LED L A Link Activity indicates the proper operation of the connection betwwen the switch and your computer Each Ethernet Alyseum product are quiped by its own indicators on the RJ45 e Connect your modules on ports 2 to 5 e Connect a computer on port 2 to 5 is possible ALYSEUM Ethernet MIDI Oo 9 l Page 5 MS SW5 User s manual Revision 1 1 5 Miscellaneous 5 1 Disclaimer All rights reserved Reproduction in whole or part of this document is prohibited without the express permission of Alyseum O 2011 2015 Alyseum The information and specifications described in this manual are subject to change without prior notice Throughout this manual trademarked names might be used We state herein that we are using the name to the benefit of the trademark owner with no intention of infringement 5 2 Maintenance Switch Off the power before maintenance Do not attempt to clean the unit with chemical solvents thinner benzene or alcohol as this might damage the fini
3. MS SW5 Users manual O Revision 1 1 More than technology MS SW5 User s manual This symbol is intended to alert the user of important operating and maintenance servicing instructions in the literature provided with the equipment This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may present a risk of electric shock Read Instruction Read and understand all of the safety and operating instructions before using this equipment Retain Instructions The safety instructions should be kept for future reference Follow Warnings Follow all warnings and instructions marked on the equipment or in the user manual Avoid Attachments Do not use tools or attachments that are not recommended by Alyseum because they may be hazardous A Installation e Choose the installation location of your unit carefully e Avoid placing it in direct sunlight or close to a source of heat e Also avoid locations subject to vibrations and excessive dust heat cold or moisture A Power Source e This equipment should only be operated from the power source indicated on the product A Servicing Refer all servicing to qualified service personnel There are no user serviceable parts inside To prevent the risk of shock do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards A
4. WARNING TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE Page 1 MS SW5 Users manual Revision 1 1 2 Contents 1 E A e PE E E E a r a tanalesseualecatenets 1 2 COMES o a 2 3 Wak Ste MS OWS Vieri a i a e a aa 3 3 1 miis 00 Oo A UU 3 3 2 SS PEC AMAN E E E do ur ua 3 4 mto ANC i dar ate ld 4 4 1 Package COMEN ia A ATi 4 4 2 ACCOSSOMES ri 4 4 3 Installing the MS SW5 into the A 100 rack oooccccccoccocococcnnconoconconononnononcnnnonanonnonanennnnnnnnnnnnos 4 4 4 Front panel descriptiON ooccoconcoccnccccncconccnnnoconnononnonononnnnonnnnonnnnonannonnnnnnnnnnnnnnnnnnnannenannnnnnns 5 5 WITS CCN ANC OU eiro a a a a a A E E DT 6 5 1 DISCIIIMO ais ai 6 9 2 Mamtenante nat eso 6 9 3 Static Electriciby ESD it id 6 5 3 1 Some tips and precautions for ESD sensitive environment eeeeseeeesse 6 5 3 2 Standard symbols for ESD advertiSiNQ ooonccococoncnnococoncononcnnononnnnnonanonoonononnnnncnnonnanenoss 6 9 4 Statement and Agency COMP IANCe cccoooccccccocnococoncnnncnanononannncononnnnonnnnonnnnannncnnannnnennnnanos 7 SA1 WEEE for EU COUHITIOS iria lola 7 5 4 2 RoHS Compliance for EU COUN TIES cccoonccnccconconccoconconoccnnononnnnonnnnnnnonanennononranonnnnonos 7 OS SOESMOPEU COLA MOS ar a e ai 7 9 0 Warranty and TOD aI ssepe AA A AAA T Page 2 MS SW5 Users manual Revision 1 1 3 What s the MS SW5
5. e Alyseum assumes no liability as a consequence of such events under the terms of this Warranty Please consult your shop for more details Page 7
6. r To install MS SW5 yourself pay attention to the following notes e First of all take the A 100 rack s mains plug out of the wall socket e Check very carefully that the red wire of the flat cable is connected to the minus 12Volts on the A 100 bus board e Failure to check this may result in the module s instant destruction as soon as the power is turned back on e The module has to be connected only to an A 100 bus board that is powered by a specified A 100 power supply with 5 Volts rail e For damaged modules that have been connected obviously in the wrong way to the bus board the warranty is void e Place the module carefully into the space in the rack and fasten it firmly in place with the supplied screws and nylon washers Put back any covers or blanking plates and screw them in firmly e Now plug the system A 100 back into the main power supply and switch it on Test out the newly installed MS SW5 If it doesn t seem to be working as expected immediately disconnect the system from the power supply again In this case double check the connections making completely sure that the ribbon cable is the right way round where it connects to the module and the bus Page 4 MS SW5 Users manual Revision 1 1 4 4 Front panel description 1 Green LED Power MS SW5 2 Yellow LED Link Activity LK ACT Mode LED Pattern OFF LINK established Network activity ON with OFF pulses 3 RJ 45 5 ports 100Mbits
7. r human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources 3 Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling 5 4 2 RoHS Compliance for EU countries Alyseum products comply with the European Union restriction of the use of certain hazardous substances in electronics equipment RoHS directive 2002 95 EC The RoHS directive prohibits the sale of certain electronic equipment containing some hazardous substances such as Mercury Lead Cadmium Hexavalent chromium and certain Flame retardants PBB amp PBDE in the European Union http eur lex europa eu LexUriServ LexUriServ do uri CELEX 32002L0095 EN HTML 5 4 3 CE for EU countries C Alyseum products comply with the requirements of European Directive 89 336 EC 5 5 Warranty and repair Alyseum warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for a period of two years from the date of purchase This warranty does not apply to any products which have been repaired or altered by other than repair personnel authorized by Alyseum or which have been subject to ESD moisture abuse accident or improper installation and us
8. sh Use only a clean dry cloth 5 3 Static Electricity ESD Electrostatic discharge ESD can cause malfunction and or damage to electronic devices if discharged into the device Despite Alyseum products having built in protections against ESD voltages might build up at levels that could harm your equipment 5 3 1 Some tips and precautions for ESD sensitive environment e Make sure to discharge any built up static electricity from yourself and your devices before touching or connecting one device to another e Ground yourself by touching an earth grounded metal surface before handling your device and other equipments For fixed installations put the device in a grounded metallic rack Ensure air relative humidity is minimum 60 Install ESD specific prevention items such as grounding mats Reduce movement speed in handling or dis connecting devices Avoid carpet or other synthetic flooring 5 3 2 Standard symbols for ESD advertisin AA AZ Wy Page 6 MS SW5 Users manual Revision 1 1 5 4 Statement and Agency Compliance 5 4 1 WEEE for EU countries Waste Electrical and Electronic Equipment Directive 2002 96 EC Applicable for E U Customers or others countries with separate collection systems 1 This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life 2 To prevent possible harm to the environment o
Download Pdf Manuals
Related Search