Stage 64 I/O Card Installation Guide
Contents
1. 192 Analog Input card DSI 192 Digital Input card SRO 192 Analog Output card DSO 192 Digital Output card Stage 64 supports installation of up to eight input cards providing a maximum of 64 input channels and up to four output cards providing a maximum of 32 output channels Installation is the same for each of these cards For instructions on installing and connecting the ANO A Net Option card see the documentation included in its package Stage 64 I O Card Features and Capabilities SRI 192 Analog Input Card Eight channels of analog mic line inputs via XLR 3 female connectors 48V phantom power 20 dB pad and phase reverse all selectable per channel via the control surface and VENUE software Signal and phantom power LEDs for each channel 24 bit A D conversion up to 192 kHz sample rate DSI 192 Digital Input Card Eight channels of digital inputs via four two channel AES EBU XLR3 female connectors or a single ADAT TOSLINK opti cal connector e Automatic sample rate conversion SRC and detection on input manually defeatable for lowest possible input latency e SRC and Lock status LEDs for both AES and ADAT connections Word clock output for synchronizing external digital devices SRO 192 Analog Output Card Eight channels of analog line outputs via male XLR 3 connectors e Automatic muting for system protection Signal and Mute LEDs for each channel 24 bit D A conversion DSO 192 Digital Output Card2. is highlighted in blue Under Information tap Settings The I O card slots of the selected Stage 64 are listed showing the cards that are currently in stalled Slots without cards are indicated as empty The newly installed Stage 64 I O card should appear in the slot in which you installed the card For instructions on using the Stage 64 see the VENUE S6L System Guide included with the S6L system software in your Avid account Stage 64 I O Card Installation Guide Compliance Information Environmental Compliance Disposal of Waste Equipment by Users in the European Union This symbol on the product or its packaging indicates that this product must not be disposed of with other waste Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city recycling office or the dealer from whom you purchased the product Proposition 65 Warning A This product contains chemicals including lead known to the State of California to cause cancer and birth defects or other re productive harm Was
3. AV I gt Stage 64 1 0 Card Installation Guide for VENUE S6L Systems Legal Notices 2015 Avid Technology Inc Avid all rights reserved This guide may not be duplicated in whole or in part without the written consent of Avid 003 192 Digital I O 192 I O 96 I O 96i I O Adrenaline AirSpeed ALEX Alienbrain AME AniMatte Archive Archive II Assistant Station AudioPages AudioStation AutoLoop AutoSync Avid Avid Active Avid Everywhere Avid Advanced Response Avid DNA Avid DNxcel Avid DNxHD Avid DS Assist Station Avid Ignite Avid Liquid Avid Media Engine Avid Media Processor Avid MEDIArray Avid Mojo Avid Remote Response Avid Unity Avid Unity ISIS Avid VideoRAID AvidRAID AvidShare AVIDstripe AVX Beat Detective Beauty Without The Bandwidth Beyond Reality BF Essentials Bomb Factory Bruno C 24 CaptureManager ChromaCurve ChromaWheel Cineractive Engine Cineractive Player Cineractive Viewer Color Conductor Command 8 Control 24 Cosmonaut Voice CountDown d2 d3 DAE D Command D Control Deko DekoCast D Fi D fx Digi 002 Digi 003 DigiBase Digidesign Digidesign Audio Engine Digidesign Development Partners Digidesign Intelligent Noise Reduction Digidesign TDM Bus DigiLink DigiMeter DigiPanner DigiProNet DigiRack DigiSerial DigiSnake DigiSystem Digital Choreography Digital Nonlinear Accelerator DigiTest DigiTranslator DigiWear DINR DNxchange Do More DPP 1 D Show DSP Manager DS S
4. Eight channels of digital outputs via four two channel AES EBU XLR3 male connectors and or a single ADAT TOSLINK optical connector Simultaneous output to both AES EBU outputs and ADAT optical output e Automatic muting for system protection Signal and Mute LEDs for each AES EBU channel pair Overview 1 What s Included I O card packages includes the following items I O card Health and Safety guide Avid Registration card Warranty claims card This guide System Requirements and Compatibility Avid can only assure compatibility and provide support for hardware and software it has tested and approved SRI 192 DSI 192 SRO 192 and DSO 192 cards are compatible with Stage 64 I O racks connected to VENUE S6L systems running VENUE software 5 0 and higher For complete system requirements and other compatibility information www avid com compatibility Conventions Used in This Guide All of our guides use the following conventions to indicate menu choices and key commands Convention Options gt System In the VENUE software click Options to display the Options tab then click the System tab File gt Save Choose Save from the File menu Control N Hold down the Control key and press the N key Control click Hold down the Control key and click the mouse button Right click Click with the right mouse button The names of Commands Options and Settings that appear on screen are in a different fo
5. Rocket Surfer Reso RetroLoop Reverb One ReVibe Revolution rS9 rS18 RTAS Salesview Sci Fi Scorch ScriptSync SecureProductionEnvironment Shape to Shape ShuttleCase Sibelius SimulPlay SimulRecord Slightly Rude Compressor Smack Soft SampleCell Soft Clip Limiter SoundReplacer SPACE SPACEShift SpectraGraph SpectraMatte SteadyGlide Streamfactory Streamgenie StreamRAID SubCap Sundance Sundance Digital SurroundScope Symphony SYNC HD SYNC I O Synchronic SynchroScope Syntax TDM FlexCable TechFlix Tel Ray Thunder TimeLiner Titansync Titan TL Aggro TL AutoPan TL Drum Rehab TL Everyphase TL Fauxlder TL In Tune TL MasterMeter TL Metro TL Space TL Utilities tools for storytellers Transit TransJammer Trillium Lane Labs TruTouch UnityRAID Vari Fi Video the Web Way VideoRAID VideoSPACE VTEM Work N Play Xdeck X Form and XMON are either registered trademarks or trademarks of Avid Technology Inc in the United States and or other countries The Interplay name is used with the permission of the Interplay Entertainment Corp which bears no responsibility for Avid products All other trademarks are the property of their respective owners Bonjour the Bonjour logo and the Bonjour symbol are trademarks of Apple Computer Inc Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation in the U S and or other countries This product may be protected by one or more U S and non U S patents Detai
6. es e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consultthe dealer or an experienced radio TV technician for help Any modifications to the unit unless expressly approved by Avid could void the user s authority to operate the equipment Australian Compliance Canadian Compliance This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada CE Compliance EMC Safety and ROHS CE Avid is authorized to apply the CE Conformite Europenne mark on this compliant equipment thereby declaring conformity to EMC Directive 2004 108 EC Low Voltage Directive 2006 95 EC and RoHS Directive 2011 65 EC Korean EMC Compliance o 7171 7R S BE AAA 71241 IRAAN ARB SHE ASA AGS F NSU 12 Stage 64 I O Card Installation Guide
7. f explosion if battery is incorrectly replaced Replace only with the same or equivalent type 18 The power inlet is the main disconnect device and should remain accessible Disconnect the power cord before servicing the unit 19 The equipment shall be used at a maximum ambient temperature of 40 C 20 Disconnect power from mains before opening the product Contents DIE del REAL ail 1 Stage 64 I O Card Features and Capabilities eee eens 1 What s Included Tn APERTE e E System Requirements and Compatibility dubbi iube fugit asd Luni baita 2 Conventions Used in This Guide sx ke css univ ai one RARE RR RARE EER RS 2 i l0 hb 059949 ERETTILE PERITI ETRE PIPER 3 Installing and Confirming I O Cards ennen nen nee RK ers 5 Installing I O Cards in the Stage 64 TERT TEDUCEE eani NEEE te Reed SERENE 5 Confieming insiallationi argo Race CHOR RU PY ECRIRE ROLACR NER RA Ras D Ede RIDE REOR RO RC RR GEO CE ob 10 Appendix A Compliance Information CEI TI sale Paste CORRI e dieque 11 Environmental Compliance eri 33 75 ers sei se ch bd bb da bap rin E RO KOC X GO ER 11 EMC Electromagnetic Compliance PERIT RT TORE ac Mire diario 14 Stage 64 I O Card Installation Guide v Overview This guide provides instructions for installing the following I O cards in VENUE Stage 64 I O racks SRI
8. h hands after handling Perchlorate Notice This product may contain a lithium coin battery The State of California requires the following disclosure statement Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate Recycling Notice ay Le EMC Electromagnetic Compliance This model Artist Mix complies with the following standards regulating interference and EMC FCC Part 15 Class B EN 55022 Class B EN 55024 Class B AS NZS CISPR 22 Class B CISPR 22 Class B Compliance Information 11 FCC Compliance for United States Radio and Television Interference Communication Statement NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measur
9. in slots J M Installing and Confirming VO Cards 5 5 Remove the blank card slot cover by unscrewing the two Philips head screws that secure the cover to the Stage 64 HEADPHONES NETWORK Stage 64 Figure 2 Blank card slot cover on the front of the Stage 64 6 Remove the I O card from its packing material and hold the card by its edges making sure the latches on the port on the back of the card are pushed inward 1 Mounting guide pin Ribbon cable port Port latches Mounting bracket Figure 3 Stage 64 I O card showing brackets and connector 6 Stage 64 I O Card Installation Guide 7 Gently slide the card into the slot Figure 4 making sure that inside the Stage 64 the pin at the top of the back of the card aligns with the corresponding guide hole on the chassis Figure 5 Figure 4 Sliding the card into the Stage 64 SRO card shown Figure 5 Guide pins and guide holes inside the Stage 64 Installing and Confirming O Cards 7 8 Push the card into the slot so it is flush with the front panel and tighten the two captive thumbscrews on the front of the card to secure it to the Stage 64 n If the card does not slide all the way into the slot make sure the latches on the port of the card are pushed fully inward M he ald NM NE a Ma r Figure 6 Tightening the front captive thumbscrews 9 Inside the back of the Stage 64 tighten the single captive thumbscrew to
10. ls are available at www avid com patents Product features specifications system requirements and availability are subject to change without notice Guide Part Number 9320 65329 00 REV A 9 15 Safety Compliance Safety Statement This equipment has been tested to comply with USA and Canadian safety certification in accordance with the specifications of UL Standards UL60065 7th IEC 60065 7th and Canadian CAN CSA C22 2 60065 03 Avid Inc has been authorized to apply the appropriate UL amp CUL mark on its compliant equipment Warning RISK OF ELECTRIC SHOCK DO NOT OPE AN Important Safety Instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings A Follow all instructions oa Only perform the services explicitly described in the install and or user manual For services or procedures not outlined in the install or user manual speak with authorized service personnel 6 Do not use this equipment near water N Clean only with dry cloth 8 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 9 Do not install near any heat sources such as radiators heat registers stoves or other equipment including amplifiers that produce heat 10 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding
11. nt The following symbols are used to highlight important information CE User Tips are helpful hints for getting the most from your system A Important Notices include information that could affect your data or the performance of your system Shortcuts show you useful keyboard or mouse shortcuts Cross References point to related sections in this guide and other VENUE guides 2 Stage 64 I O Card Installation Guide Resources The Avid website www avid com is your best online source for information to help you get the most out of your Avid system The following are just a few of the services and features available Account Activation and Product Registration Activate your product to access downloads in your Avid account or quickly create an account if you don t have one Register your purchase online download software updates documentation and other resources https www avid com US account Support and Downloads Contact Avid Customer Success technical support download software updates and the latest online manuals browse the Com patibility documents for system requirements search the online Knowledge Base or join the worldwide Avid user community on the User Conference https www avid com US Support index html Training and Education Study on your own using courses available online find out how you can learn in a classroom setting at an Avid certified training center or view a webinar For e
12. prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 11 Protect power cords from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the equipment 12 Only use attachments accessories specified by the manufacturer 13 For products that are not rack mountable Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the equipment When a cart is used use caution when moving the cart equipment combination to avoid injury from tip over 14 Unplug this equipment during lightning storms or when unused for long periods of time 15 Refer all servicing to qualified service personnel Servicing is required when the equipment has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the equipment the equipment has been exposed to rain or moisture does not operate normally or has been dropped 16 For products that are a Mains powered device The equipment shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the equipment Warning To reduce the risk of fire or electric shock do not expose this equipment to rain or moisture 17 For products containing a lithium battery CAUTION Danger o
13. secure the card to the chassis Figure 7 Securing the card to the Stage 64 chassis 10 On the card push the latches outward 8 Stage 64 I O Card Installation Guide 11 Locate the corresponding ribbon cable all ribbon cables in the Stage 64 are cut to length and push the cable connector into the port on the card so that the latches on the port move inward and lock the connector to the port on the card Double check to make sure the card is connected securely Figure 8 Connecting the I O card to its corresponding ribbon cable 12 After all cards have been installed replace the back panel making sure to properly align the guide pins on the back panel to the guide holes and secure it to the Stage 64 by tightening the captive thumbscrews Figure 9 Back panel guide pins 13 Proceed to Confirming Installation on page 10 Installing and Confirming VO Cards 9 Confirming Installation After you have installed an I O card you should confirm that you have installed it properly To complete and confirm installation 1 2 3 10 Connect the power cables to the Stage 64 and to a power source Connect the Stage 64 to the rest of your S6L system Power on your Stage 64 and the rest of the components of your S6L system In the VENUE software screen go to the Options gt Devices page In the Available Devices or Connected Devices columns tap the icon of the Stage 64 in which you installed the I O card so it
14. torageCalc DV Toolkit DVD Complete D Verb Eleven EM Euphonix EUCON EveryPhase Expander ExpertRender Fairchild FastBreak Fast Track Film Cutter FilmScribe Flexevent FluidMotion Frame Chase FXDeko HD Core HD Process HDpack Home to Hollywood HyperSPACE HyperSPACE HDCAM iKnowledge Impact Improv INEWS iNEWS Assign iNEWS ControlAir InGame Instantwrite Instinct Intelligent Content Management Intelligent Digital Actor Technology IntelliRender Intelli Sat Intelli Sat Broadcasting Recording Manager InterFX Interplay inTONE Intraframe iS Expander iS9 iS18 iS23 iS36 ISIS IsoSync LaunchPad LeaderPlus LFX Lightning Link amp Sync ListSync LKT 200 Lo Fi MachineControl Magic Mask Make Anything Hollywood make manage move media Marquee MassivePack MassivePack Pro Maxim Mbox Media Composer MediaFlow MediaLog MediaMix Media Reader Media Recorder MEDIArray MediaServer MediaShare MetaFuze MetaSync MIDI I O Mix Rack Moviestar MultiShell NaturalMatch NewsCutter NewsView NewsVision Nitris NL3D NLP NSDOS NSWIN OMF OMF Interchange OMM OnDVD Open Media Framework Open Media Management Painterly Effects Palladium Personal Q PET Podcast Factory PowerSwap PRE ProControl ProEncode Profiler Pro Tools Pro Tools HD Pro Tools LE Pro Tools M Powered Pro Transfer QuickPunch QuietDrive Realtime Motion Synthesis Recti Fi Reel Tape Delay Reel Tape Flanger Reel Tape Saturation Reprise Res
15. xample check out the live sound webinars hosted by Robert Scovill https www avid com US resources live sound webinar registration Products and Developers Learn about Avid products download demo software or learn about our Development Partners and their plug ins applications and hardware https www avid com US Products index html Overview 3 4 Stage 64 I O Card Installation Guide Installing and Confirming I O Cards This section shows how to install an I O card in the Stage 64 I O rack and confirm installation For operational information see the VENUE S6L System Guide Installing I O Cards in the Stage 64 To install an SRI SRO DSI or DSO card 1 Shut down your VENUE system and power down your Stage 64 2 Disconnect all cables from your Stage 64 3 Remove the back panel of your Stage 64 by loosening the eight captive thumbscrews completely using a 2 Philips screwdriver if necessary and set the panel aside Stage 64 Figure 1 Stage 64 back panel captive thumbscrews 4 On the front of the Stage 64 locate the slot where you want to install the input or output card Each slot is lettered and corre sponds to the card slot shown along the top of the VENUE Patchbay patching grid depending on the type of card installed input or output card Observe the following requirements when installing I O cards in Stage 64 Input Cards SRI and DSI Are installed in slots A H Output Cards SRO and DSO Are installed
Download Pdf Manuals
Related Search