Spirotech template_S6.indd
Contents
1. Refill 5 4 2 Start up applies to types S6A R and S6A R 2P ON OFF 3 Feed a 3 core supply cable through swivel C and connect this to connector J16 4 If a BMS is used feed in the BMS cable through swivel E and connect this to connector J20 With the types S6A R and S6A R 2P 1 If an external device controls the refill feed in a cable through swivel D and connect this to connector J21 5 4 Commissioning 5 4 1 Preparation On off Display Status report in operation OK Up Confirm Enter Menu Down Cancel Exit Status report failure CAUTION A The start up routine starts automatically when the unit is switched on for the first time Press EXIT to go back one step in the menu while programming User manual version 1 1 English 29 SPIRO TECH FOR BETTER PERFORMANCE Follow the procedures given below for entering the required parameters Set date en time Press ON OFF Select a language using A and V Press ENTER Set the date using A and WV Press ENTER Set the day using A and V Press ENTER Set the time using A and V Press ENTER 9 aN Filling the unit 1 Press ENTER two times The unit starts filling 2 Wait for 20 seconds until Initial fill busy disappears 3 Loosen the air vent screw A a few turns and tighten it again when air has stopped coming out 4 Repeat steps 1 3 until water star2. O does not run Check the pump Check and replace the pump fuse in the control unit The unit sucks in air during the vacuum phase Replace the automatic air vent The pressure switch S is defect Replace the pressure switch Err 7 Fluid lack vessel There is a risk of running dry the fluid level in the vessel is at the minimum The automatic air vent A is defect or blocked Replace the automatic air vent The vessel has not been filled Fill the vessel see 5 5 4 The level switch H is defect Replace the level switch The unit runs continuously and does not switch off automatically The SmartSwitch does not seem to work The content of dissolved gases has not reached the minimum yet Check whether there is a possibility of gases entering The SmartSwitch R is defect Disconnect the hose on the automatic air vent Replace the SmartSwitch if the unit does not switch off after 10 minutes The automatic air vent A is defect Check whether gas is released through the valve Replace the automatic air vent when no gas is released The unit runs maximally 10 min per degassing period Gases remain in the installation The SmartSwitch does not seem to work The SmartSwitch R is defect Check whether gas is released through the valve Replace the SmartSwitch if gas is released The automatic air vent A is defect Replace the
3. a drain line H to the drain connection G Drain the unit through the drain connection G Open the air vent screw on the main pump to completely empty the unit See the figure in 5 4 2 33 SPIRO TECH FOR BETTER 7 3 Failure table General PERFORMANCE The letter indications comply with the main figure in 2 1 An overview of the replacement parts has been included in 8 2 SPIROVENT SUPERIOR Problem Possible cause Correction Err 3 Syst temp too low There is a risk of freezing The temperature of the system fluid is lt 0 C Provide a temperature of gt 0 C Err 4 Syst temp too high There is a risk of boiling The temperature of the system fluid is gt 90 C Provide a temperature of lt 90 C Entrance flow Err 5 The flow in the inlet line has been blocked The solenoid valve N in the inlet line does not open Replace a part of the solenoid valve A valve in the inlet line is closed Open the valve The inlet line has been blocked Remove the blocking The pressure switch S is defect Replace the pressure switch Err 6 Flow The flow in the outlet line has been blocked One of the solenoid valves N is not closing Replace a part of the solenoid valve The valve in the outlet line is closed Open the valve The outlet line has been blocked Remove the blocking The pump
4. automatic air vent The refill mode remains active this applies to types S6A R and S6A R 2P 34 English User manual version 1 1 SPIR TECH FOR BETTER Specific for types S6A R and S6A R 2P PERFORMANCE SPIROVENT SUPERIOR Problem Possible cause Correction Err 1 Psystem too low The system pressure is below 1 bar A failure in the installation Provide a system pressure of gt 1 bar There is a leak in the installation Repair the leak The pressure sensor Q is defect Replace the pressure sensor Err 2 Psystem too high The system pressure exceeds the set maximum A failure in the installation Provide a system pressure that is below the set value The set value is too low Increase the set value The pressure sensor Q is defect Replace the pressure sensor Err 10 Refill flow too low There is no or little supply of refill fluid A valve in the refill line is partly closed Open the valve The solenoid valve N in the refill line does not open Replace a part of the solenoid valve The refill line has been blocked Remove the blocking The water flow meter G is defect Replace the water flow meter Err 11 Refill valve Undesired supply of refill fluid The refilling does not stop The solenoid valve N in the refill line does not close Replace a part of the solenoid valve Er
5. guarantee lapses in cases of faulty installation incompetent use and or non authorised personnel trying to make repairs Consequential damage is not covered by the The guarantee for Spirotech products is valid until 2 guarantee years following the purchasing date 9 1 Terms of guarantee 10 CE STATEMENT 10 1 Declaration of conformity EU declaration of conformity We Spirotech bv Churchilllaan 52 Helmond NL declare entirely on our own responsibility that the products SpiroVent Superior S6A S6A R S6A R 2P to which this declaration applies comply with the standards EN 292 1 EN 292 2 EN 809 EN 60204 1 EN60335 1 EN 55014 1 and EN 55014 2 EN 61000 3 2 EN 61000 3 3 EN 61000 6 2 and EN 61000 6 4 in accordance with the stipulations of the Machine Directive 89 392 EEC amended by directives 91 368 EEC 93 44 EEC and 93 68 EEC the Low Voltage Directive 2006 95 EC The EMC Directive 89 336 EEC amended by directives 92 31 EEC and 93 68 EEC Helmond January 2009 Daphne Scholten General Manager 38 English User manual version 1 1 SPIR TECH FOR BETTER PERFORMANCE The manufacturer reserves the right to make changes without prior notification Copyright Spirotech bv Information given in this brochure may not be reproduced complete or in part without the prior written consent of Spirotech bv Spirotech bv The Netherlands www spirotech com
6. t Noise level Approx 57 dB a Approx 57 dB a Approx 57 dB a Refill connection n a Swivel G34 f t Swivel G34 f t 3 3 Electrical specifications S6A S6A R S6A R 2P Supply voltage 230 V 10 50 or 60 Hz 230 V 10 50 or 60 Hz 230 V 10 50 or 60 Hz Absorbed power 800 W 800 W 1300 W Nominal power consumption 3 5 A 3 5 A 5 5A Starting current 2 6 nominal current 2 6 nominal current 2 6 nominal current Protection 10 A 3 15 A T 10 A 3 15 A T 10 A 3 15 A T Protection class IP 44 IP 44 IP 44 Max load of potential free 24V 1A 24V 1A 24V 1A contacts Supply voltage for BMS 24 Vac 24 Vac 24 Vac control voltage of BMS Supply voltage of external n a 5 Vac 5 Vac refill signal supplied voltage 3 4 Other specifications S6A S6A R S6A R 2P System pressure 1 6 bar 1 6 bar 1 6 bar Ambient temperature 0 40 C 0 40 C 0 40 C Maximum compression 10 bar 10 bar 10 bar pressure with closed valve behind pressure gauge Refill flow n a See graph in 6 1 See graph in 6 1 System fluid temperature 0 90 C 0 90 C 0 90 C Refill pressure 0 6 bar 0 6 bar 0 6 bar Refill fluid temperature n a 0 70 C 0 70 C User manual version 1 1 English 25 SPIRO TECH FOR BETTER PERFORMANCE 3 5 Building Management System BMS The unit has been prov
7. unit empty weight 10 kg Floor mounting Place the unit on a flat surface Mount the unit on the floor using the holes B Move the unit with two persons to the place of installation Lift the unit using the handles C User manual version 1 1 English 27 SPIRO TECH FOR BETTER PERFORMANGE SPIROVENT SUPERIOR 5 3 2 Installation With the types S6A R and S6A R 2P f Insert a valve F and a non return protection E in Mechanical the refill fluid supply line 2 Connect the supply line to the refill connection G of the unit CAUTION A Use a locally approved non return protection A non return protection can be optionally delivered Make sure that the pressure in the refill line is below the system pressure This prevents undesired refilling in case of failure of the refill line Make sure that the lines leave the unit at the rear Electrical SSi 1 Make two branch lines 3 4 A on the side of the CAUTION main transport line The distance between them UN Gent tense 500 mri A Preferably use a wall socket for the power supply to the unit This should 2 Insert a valve B in each branch With this the unit always be accessible can be depressurised y Mount an all pole main switch contact opening gt 3mm if the unit is directly CAUTION connected to the power supply Make sure that the valves are opened before Use supply cables with the correct putting the unit into ope
8. 19 09401 SPIR TECH FOR BETTER SPIRO VENT SUPERIOR S6 PIR ppT CH FOR BETTER PERFORMANCE TABLE OF CONTENTS 7 Preface 21 2 Introduction 22 3 Technical specifications 24 4 Safety 26 5 Installation and commissioning 27 6 Use 32 7 Failures 33 8 Maintenance 36 9 Guarantee 38 10 CE statement 38 All rights reserved No part of this manual may be duplicated and or made public through the Internet by means of printing photocopying microfilm or in any other way without prior written permission from Spirotech bv This manual has been composed with the utmost care Should however this manual contain any inaccuracies Spirotech bv cannot be held responsible for this SPIROVENT SUPERIOR 1 PREFACE This user manual involves the installation commissioning and operation of the SpiroVent Superior of the types S6A S6A R and S6A R 2P Always carefully read the instructions before installation commissioning and operation Keep the instructions for future reference 1 1 Symbols Throughout the instructions the following symbols are used Warning or important note Note Risk of electric shock Risk of burning gt e 9o User manual version 1 1 English 21 SPIRO TECH FOR BETTER PERFORMANCE 2 INTRODUCTION 2 1 Overview of the unit SPIROVENT SUPERIOR Superior S6A R 2P Automatic air vent Deaeration vessel Inlet hose Refill connecti
9. ad the data on the type plate User manual version 1 1 SPIR TECH FOR BETTER 5 PERFORMANCE INSTALLATION AND COMMISSIONING A SPIROVENT SUPERIOR Installation and mounting CAUTION Install the unit in accordance with the 5 1 Installation conditions 0 local guidelines and rules Install the unit on a frost free well ventilated place Install the unit as bypass on the main Electrically connect the unit to a 230 V 50 60 Hz transport line of the installation socket Make sure the expansion system has the proper NOTE dimensions The water displacement in the unit can oomi Preferably install the unit at the point in cause pressure variations in the installation There must be overpressure in the installation This prevents spontaneous aeration 5 2 A Unpack WARNING Do not hoist the unit when unpacked The use of webbing slings chains and hooks can cause irreparable damage The unit is delivered on a pallet 1 Remove the packaging 2 Loosen the screw A half a turn 3 Remove the cover B from the unit 5 3 1 the installation with the lowest temperature Here the most dissolved gases are found in the fluid Make sure when installing that the operating panel is always easily accessible Mounting O O YR ey iff Wall mounting Mount the unit on the wall using the holes A Make sure that the mounting can carry the filled
10. ed successfully 9 Press MENU Select Manual operation using A and V Press ENTER 10 Select Reset using A and V Press ENTER a EF NOTE The green LED OK indicates that the unit is ready for use 5 5 5 Reading the memory During operation the following data are stored in the memory Accumulative running hours Degassing history Fault history Refilling history only with types S6A R and S6A R 2P The memory can be read in the following way 1 Press MENU Select User menu gt History using A and V Press ENTER 2 Select Fault history or Operation history using A and V Press ENTER 3 Select an item using A and Y Press ENTER 4 Repeatedly press EXIT to return to the status report 5 5 6 Reading data The following general data have been stored in the memory of the unit Unit type Software version Installation date The general data can be read in the following way English 31 SPIRO TECH FOR BETTER PERFORMANCE SPIROVENT SUPERIOR With the types S6A R and S6A R 2P The amount of fluid that is added B depends on the difference A between the system pressure and 1 Press MENU Select User menu gt General info using A and V Press ENTER 2 Select an item using A and Y Press ENTER 3 Repeatedly press EXIT to return to the status report 6 USE 6 1 General The display lighting automatically dims after no key has been pressed for 5 minutes Press a ke
11. ided with auxiliary contacts for communication with a BMS The BMS has to offer the 24 Vac voltage SPIROVENT SUPERIOR Signal S6A S6A R S6A R 2P Unit in operation Potential free Potential free Potential free Unit failure Potential free Potential free Potential free Unit release stop 24 Vac 24 Vac 24 Vac Refill by BMS n a 24 Vac 24 Vac 4 SAFETY WARNING A Installation and maintenance of the unit should only be carried out by authorised personnel Remove the voltage and pressure from the unit before starting the activities WARNING A There are hot parts below the cover Let the unit cool down before starting the activities 4 1 CE marking The unit has a CE marking This means that the unit has been designed constructed and tested in compliance with the current safety and health regulations Provided that the user manual is adhered to the unit can be safely used and maintained 26 English 4 2 Type plate SpirRoVENT SUPERIOR Type Power input Voltage IP class Pressure Temperature Serial number Year of manufacture SPIROTECH bv Helmond The Netherlands ee A B C D E F G 4 Type of the unit Absorbed power Supply voltage Protection class System pressure System temperature Serial number Year of construction The type plate has been applied on the inside of the unit Remove the cover to re
12. lish User manual version 1 1 PIR ppT CH 7 7 1 A a gt 4 User manual version 1 1 FOR BETTER PERFORMANCE FAILURES Remedy failures WARNING In case of failure always warn the installer Remove the voltage and pressure from the unit before starting the activities see S 7 2 Pressing ON OFF does not remove the voltage from the unit WARNING There are hot parts below the cover Let the unit cool down before starting the activities NOTE In case of a failure the red LED is lit The failure report appears in the display NOTE With the types S6A R and S6A R 2P the seriousness of the failure determines whether the whole unit or a part of the unit switches off With partly switching off the refilling process remains active In this case both the red and the green LEDs are lit Localise the failure using the failure table see 7 3 If necessary put the unit out of operation see 7 2 Remedy the failure Reset the unit see 7 3 1 or put the unit into operation again see 5 5 4 7 2 m English SPIROVENT SUPERIOR Putting out of operation Take the plug out of the wall socket or switch off the main switch Make sure that switching on the voltage unintentionally is not possible Close the valves A and or C in the inlet line and B and or D in the outlet line Close if applicable the valve E in the refill supply line as well Connect
13. noid valve excluding coil 12 022 N Coil for solenoid valve 12 018 N Interior for solenoid valve 12 021 T Pressure gauge 15 513 Non return valve 15 514 A Automatic air vent 13 468 S Pressure switch 15 515 U Control unit cover incl print S6A 15 784 U Control unit cover incl print S6A R 15 785 U Control unit cover incl print S6A R 2P 15 516 J Temperature sensor 15 517 R SmartSwitch 15 518 1 P Adjustment valve 13 466 H Level switch 15 519 G Water flow meter S6A R and S6A R 2P 15 520 Q Pressure sensor S6A R and S6A R 2P 15 521 K Pump type PSAM70 A S6A R 2P 50 Hz 15 522 K Pump type PSAM706 A S6A R 2P 60 Hz 36 English User manual version 1 1 SPIR TECH FOR BETTER PERFORMANCE SPIROVENT SUPE RIOR 8 3 Maintenance card Type Serial number Installation date Installed by firm Installed by technician Inspection date Technician Initials Nature of the maintenance Inspection date Technician Initials Nature of the maintenance Inspection date Technician Initials Nature of the maintenance Inspection date Technician Initials Nature of the maintenance Inspection date Technician Initials Nature of the maintenance Inspection date Technician Initials Nature of the maintenance User manual version 1 1 English 37 SPIRO TECH pep aera PEHFORMANGE SPIROVENT SUPERIOR 9 GUARANTEE The
14. on types S6A R and S6A R 2P Valve behind pressure gauge Notch in the cover Water flow meter Level switch in bottom of vessel Adjustable inlet valve Temperature sensor Back up pump for type S6A R 2P Screw Drain connection under the vessel Solenoid valve O N N English Superior S6A R Main pump Adjustable outlet valve Pressure sensor SmartSwitch in bottom of control unit Pressure switch Pressure gauge Control unit Outlet hose Cover User manual version 1 1 SPIR TECH FOR BETTER PERFORMANCE 2 2 Operation The figure below schematically shows the operation of the unit The letter indications comply with the main figure on the previous page SPIROVENT SUPERIOR 0 Hi T Le 7 S6A R 2P O User manual version 1 1 English 23 SPIRO TECH FOR BETTER PERFORMANCE 2 2 1 General The Superior is a fully automatic vacuum degasser for installations filled with fluid The fluid contains dissolved and undissolved gases The function of the unit is to remove these gases from the installation until the concentration of undissolved gases has reached an absolute minimum Problems caused by gases in the installation are thus eliminated The types S6A R and S6A R 2P have an integrated refill automat The refill au
15. r 13 Refill freq too high Refilling takes place too frequently There is a leak in the installation Repair the leak Check the setting Max refill freq Err 14 Refill time too high Refilling takes too long There is a leak in the installation Repair the leak Check the setting Alarm refill after Err 15 Refill quantity Too much is added There is a leak in the installation Repair the leak Check the setting Alarm refill The refill mode remains active this applies to types S6A R and S6A R 2P 7 3 1 Resetting the unit 1 Press MENU Select User menu gt Manual operation using A and V Press ENTER 2 Select Manual operation reset using A and WV Press ENTER User manual version 1 1 English 35 SPIRO TECH PERFORMANCE FOR BETTER 8 MAINTENANCE SPIROVENT SUPERIOR 8 1 Periodic maintenance 1 Annually replace the interior of the solenoid valves N 8 2 Replacement parts The letter indications comply with the main figure in 2 1 Article number Letter Description 15 552 O Shaft sealing for pump type CR1 13 1 9 AAA HQQE 15 553 O Gasket set for pump type CR1 9 and CR1 13 15 554 O Condensator for pump type CR1 13 15 790 O Condensator for pump type CR1 9 15 510 O Pump type CR1 13 AAA HQQE 50 Hz 15 511 O Pump type CR1 9 AAA HQQE 60 Hz 15 512 W Cover 12 023 N Sole
16. ration dimensions Always replace a defect fuse by a fuse of the same value See 3 3 S i re J f saii NOTE se K As seen from the direction of the volume flow the first branch is the inlet into the unit 1 Loosen the screws A of the control cabinet 2 Fold down the operating panel B to the front 3 Connect the line A to the flexible outlet hose D 4 Connect the line B to the flexible inlet hose C 28 English User manual version 1 1 SPIR TECH FOR BETTER PERFORMANCE SPIROVENT SUPERIOR 1 Set the adjustment valves A and B from the position fully open with the following table Emi F2 2 Open the valve C behind the pressure gauge D dia fa E 3 Open the valves E and F in the inlet and outlet ee e ed lines j i i 4 Open the valve G in the refill line Fa j 2 System System Position Position pressure pressure adjustment adjustment bar bar valve inlet valve Medium Medium B outlet A water water glycol 1 2 3 2 2 3 2 5 2 5 3 4 2 25 connector contact connection 4 5 2 J20 1 and 2 Refill 5 6 1 75 3 and 4 Release off 1 2 6 2 5 and 6 Failure 2 3 6 2 5 7 and 8 In operation 3 6 6 6 ij J21 1 and 2
17. rent time Auto start 1 Time 1 for starting the degassing process See Auto start 1 Auto start 2 Block time day 1 Time for stopping the degassing process User manual version 1 1 SPIR TECH FOR BETTER PERFORMANCE Parameter Description Block time day 2 See Block time day 1 Block time week Days of the week on which the unit is not working After having changed this parameter select Save using A or YV Press ENTER Selected days are marked with an Block time year 1 Period per year during which the unit is not working Block time year 2 5 See Block time year 1 Max syst pressure g Pressure at which the unit stops Psystem desired Pressure at which the refilling stops Set this as low as possible if the refilling is controled by the BMS or external devices Refillpressure Pressure at which the refilling starts Set this as low as possible when the refilling is controled by the BMS or external devices Refill alarm Maximum amount of fluid that may be refilled per time 0 2500 l 0 switched off Refill alarm after Continuous refilling time 0 255 min 0 switched off Max refill freq Maximum number of times per day that refilling is allowed 0 10 times 0 switched off applies to types S6A R and S6A R 2P 5 5 2 Manual operation E NOTE If manually switched off
18. the process must be manually switched on again 1 Press MENU Select User menu gt Manual operation using A and YV Press ENTER 2 Select Manual operation start or Manual operation stop using A and V Press ENTER 5 5 3 Filling the installation Applies to types S6A R and S6A R 2P NOTE The unit also fills the installation with degassed or not degassed fluid When the desired system pressure is reached the unit automatically goes to the standby status User manual version 1 1 SPIROVENT SUPERIOR 1 Press MENU Select User menu gt Manual operation using A and V Press ENTER 2 Select Manua1 operation gt system fill using A and Press ENTER 3 Select Degassed or Non degassed Press ENTER 5 5 4 Switch on again Follow the procedure described below after the unit has been switched off 1 Set the adjustment valves from the position fully open in accordance with the table in 5 4 1 2 Press ON OFF Press ENTER two times The unit starts filling 4 Wait for 20 seconds until Initial fill busy disappears 5 Loosen the air vent screw A see figure on the previous page a few turns and tighten the screw again when air has stopped coming out 6 Repeat steps 3 5 until water starts coming out of the air vent screw at step 5 7 Also deaerate the back up pump with type S6A R 2P 8 Press EXIT two times The status menu shows the message Err 7 when the test of the run dry protection has been complet
19. tomat maintains continuous pressure in the installation For this the unit adds 2A degassed fluid if necessary The unit can also fill the entire installation with degassed fluid The type S6A R 2P also has a back up pump In case of a break down of the main pump the back up pump takes over the refill function of the main pump thus guaranteeing the system pressure 3 3 1 2 2 2 Degassing The unit starts up daily with the degassing process at a time indicated by the user The process has two phases 1 The flushing phase The fluid flows from the installation through the solenoid valve N into the vessel B The pump O continuously pumps the degassed fluid from the vessel into the installation Here the degassed fluid absorbs gases again 2 The vacuum phase The solenoid valve N regularly closes starting the vacuum phase The continuously running pump O provides underpressure in the vessel B The underpressure causes the release of the gases dissolved in the fluid which are collected at the top of the vessel The solenoid valve N opens again starting a new flushing phase The SPIROVENT SUPERIOR The unit should be used within the limits of the technical specifications as given in chapter 3 WARNING In case of doubt always contact the supplier In case of a heavily contaminated system fluid a dirt separator is to be installed in the main return line of the installation Scope of deli
20. ts coming out of the air vent screw at step 3 5 Also deaerate the back up pump with type S6A R 2P 6 Press EXIT two times The status menu shows the message Err 7 when the test of the run dry protection has been completed successfully 7 Press MENU Select Manual operation using A and V Press ENTER 8 Select Reset using A and V Press ENTER Cm NOTE The green LED OK indicates that the unit is ready for use The degassing starts by default daily at 08 00 hours 30 English SPIROVENT SUPERIOR Check operation Als Manually start the unit see 5 5 2 2 Check the indication of the pressure gauge B This should alternately display overpressure and underpressure 3 Close the valve A behind the pressure gauge B 4 Put back the cover C on the unit and fasten it with the screw D EP NOTE The SmartSwitch will automatically turn off the unit when the concentration of dissolved gases has reached the minimum level 5 5 Install and operate 5 5 1 Install Set the user parameters 1 Press MENU Select Settings using A and Y Press ENTER 2 Select the parameter to be changed using A and YV Press ENTER 3 Change the setting using A and V Press ENTER Repeat steps 2 and 3 if necessary 5 Repeatedly press EXIT to return to the status report gt Parameter Description Language Language for the display texts Date The current date Weekday The current weekday Time The cur
21. very 1x SpiroVent Superior 1x User manual 1x Non return protection optional TECHNICAL SPECIFICATIONS Dimensions gases collected in the vessel are removed from the installation through the automatic air vent A The Height mm Width mm Depth mm SmartSwitch R in the control unit makes sure that 880 590 350 the degassing is stopped as soon as the content of dissolved gases has reached the minimum level 2 2 3 Re fill The types S6A R and S6A R 2P of the unit constantly check the installation pressure The refill process starts and stops automatically at the set values The unit can also be used to automatically fill the installation with degassed fluid 2 3 Operating conditions The unit is suitable for use in systems filled with clean water or mixtures of water with a maximum of 40 glycol Use in combination with other fluids may result in irreparable damage 24 English User manual version 1 1 PIR ppT CHI FOR BETTER PERFORMANCE SPIROVENT SUPERIOR 3 2 General specifications S6A S6A R S6A R 2P Max system volume 150 m 150 m 150 m Empty weight 57 kg 59 kg 67 kg Volume of degassing vessel 8 8 8 Inlet connection Swivel G34 f t Swivel G34 f t Swivel G34 f t Outlet connection Swivel G34 f t Swivel G34 f t Swivel G34 f t Drain connection Swivel G34 m t Swivel G3 m t Swivel G34 m
22. y to activate the lighting While stopping the process a stop procedure is started making sure that the unit stops in a safe situation overpressure When a pump has not run for 96 hours an automatic pump test is run at the first next Auto start Press ON OFF to switch off the unit Press ON OFF again to switch on the unit again At low fluid temperatures condensation may occur at certain parts The condensation is drained the refill water pressure B Flow I hour through the openings in the frame A System pressure water pipe pressure bar 6 2 Status reports Report Description LED indication Auto pump test The unit runs a pump test Green End degassing The stop procedure is in process Green End refilling End systemfill Degassing The degassing process is in process Green Process stopped The unit has been stopped manually None Standby The unit is waiting for a starting signal Green Stop by BMS The BMS has stopped the unit After release by the BMS the None unit must be started manually Failure The unit has stopped because of a failure Remedy the failure Red before resetting the unit see 7 3 1 The unit is switched to one of the above statuses Refill only with S6A R The unit is refilling fluid Green and S6A R 2P Filling system The installation is filled with fluid Green only with S6A R and S6A R 2P 32 Eng
Download Pdf Manuals
Related Search