EPIK LITE USER MANUAL
Contents
1. Charger Indicator The battery charger for the EPIK Lite is equipped with an LED light indicator that works to help you preserve the battery life of your bicycle by allowing you to quickly see if your EPIK Lite is completely charged Charger Level Indicators LED STATUS an Green Fully charged Battery Precautions e Do not touch the two poles of the battery with your hands when the battery is removed for charging The two battery poles should not be touched with any other metal or other material that conducts electricity e While charging put the battery in a secure place where children cannot reach it e Do not use any other charger other than the one that came with your electric bike If you need another charger contact your local dealer or e JOE Bicycle e Do not attempt to open or repair your charger The electronics contain high pressure circuits so do not dismantle by yourself e Prevent liquids metal and metal fillings from permeating the charger and be careful to not drop or hit the charger causing it to become damaged e Do not put anything on top of the charger while charging it must be well ventilated to allow the heat generated to dissipate e When charging if there is a peculiar smell or the charger gets too hot to touch please stop charging immediately e To prevent premature failure of your battery and for your warranty to remain in effect on your battery it is RECOMMENDED that you charge and discharge your bat2. default setting Pedal Assist System will be turned on thumb throttle will be turned on and battery level indicator will be turned on e SWITCH Button o When pressing the SWITCH button once the PAS will turn off leaving only the thumb throttle turned on NOTE Handler light will be on when thumb throttle is on If thumb throttle is turned off the Handler light indicating it is turned off o When pressing the SWITCH button twice it will turn off the thumb throttle and Handler light and turn the PAS system back on giving you the chance to use the MODE options located on the bottom of the display MODE options show you how much pedal assist you are receiving from the motor e LOW you are receiving about 30 of the motors capacity e MEDIUM you are receiving about 50 60 of the motors capacity e HIGH you are receiving about 80 90 of the motors capacity e To return the LED Electric Assist back to the original settings with all options on press the SWITCH button for a third time e To turn off all electric assist hold the ON OFF button down for 3 seconds or until all LED display lights are off For your safety please turn off the power key on the battery when bike in not in operation 12 During and after Riding Instructions and Tips Once the bike is powered ON when the rider presses down on the thumb throttle the bike will move forward Do not turn the power ON until you are ready to go o Using the hand bra
3. or would like to share your e JOE bike experience with us please contact us at Telephone 855 888 1891 E Mail sales ejoebike com Website http www ejoebike net rT Like us on Facebook httos www facebook com ejoebike 17
4. FBESTUE EPIK LITE USER MANUAL Please read before operating your new bicycle e JOE Electric Bicycle Inc Phone 855 888 1891 E Mail sales ejoebike com Website http ejoebike net Contenls MOGUO gases see E tesa wala ec 5 peas sa E E E E E 3 NV EN acess cack cc csc tec cis cca ater tates oe mo econ E ceca eee peace perce eet na denned etacemeenaos 4 OS OU SC Ce acorns sro sa aera a A pace Gules ona soca unecinanncouubnais A cater bane Se escxetteces 5 SEPUCtUTe OF VOUF NEW Electric BIC VCO sip incocicsscnncantcadeansusecceadasbisvaindesuasisgusinnsieqebeienntinseaveueenaanasasuacwoeueitbeudanseesnasascarsuasncthacee aueneasies 6 Mains pecihicati ns EPIK LTE cites EE ins coeeeaccsieasenoaaneaeass 7 BI AN E coe T E E A E E E EEE O O E ENE ENE O E EE 8 DERE PEC AU Ul ONS as E A E N 8 Seat and Handlebar Safe Height MarK cccccssscccssecccssecceseccceeccceeececenceeeneceeenceeenecseeeceesueceseececeueceseaceteneceeeueesaaectseecetsneeegs 9 Vertical Handle Stem Position Handlebars cccccceccccescccesececcuccceecsceucseeeceeeueseeueeeeeceeeueeeeeuseueuceseeeseeueseueseeeueeseneeeas 9 PRIS Ment Meno aeran r EE E A E E 9 SET CUNO PO SIO aer E E cuslewananonealasaneca 9 Barten ma Cia er NACA O S iann ea A E EE 10 BEA ES O E E A E 10 Bicycle Battery Charge Mndicator LIC AUS serseri EREET Tann ETARTE ETENA E 10 6 aye 4 1 aa ina O TO ea E A ee ee eee ee eee eee eee eee ee 10 Bey PSC AU COU NS a ccc on tea ory ea csstaa
5. e it easier for you to fall down e Remember which wheel is controlled by which brake e Please incline your body backward to reduce the influence of inertia e Adjust the brakes properly Brake pads gradually wear down during normal use If the brake pads are grinded flatly repair or replace them promptly e Check whether the braking function and braking power cut off are working properly Seat and Handlebar Safe Height Mark Vertical Handle Stem Position Handlebars Appropriate adjustments can be made for the vertical handle stem according to personal preference or driving habit but it is forbidden to expose the infix notation also called the safety line as shown in Fig 1 If used in an inappropriate way it may cause serious injury to the rider Adjustment Method e Screw down the lead screw in handle core e Move vertical handle stem to appropriate height making sure not to exceed the safety mark e Screw on the lead screw in handle core Seat Cushion Position When you sit on the seat cushion step on the pedal with your heel and lower the pedal to the lowest possible position If the leg can straighten out slightly then the height is most suitable If only the tiptoe can step on the pedal or the leg cannot straighten out slightly fatigue and sports injuries may occur Caution should be taken when making suitable height adjustments for the seat pillar The MAX mark line also called the safety line or the infix notation as sh
6. eases tompes vous sosaannsus tweed erusnaad aerse A N 11 G neral Oe Fai MTS BE uUCUONS mierenie acer ENEE EREE EETA EAEAN ip nuetoasead ete band EAE EAE 12 Before You Ride for the First Time ccccsssccccccsssseccceeeeeceeseeeeeeeeseeeeeeeeseeeeeeeeseeeeeeesseeeeeeessaeesceesaaueseeessuuuseessuueceesaaaasees 12 Electric Assist LED Operating INSU UCHIONS iiccoscticesaceitedesssenctteuncdcenccsdausantercatenusendeieaitonneseeusedsacdadtioadsdraterianesamecseeeuereseness 12 During and ater Riding Instructions and Vl OS ecccsecenssctncedccweticcuncdabacsusnavaatacectencgssnned casceacabeasnus eunmevansssdeceoeesatvesneSuncasseses 13 Une TV ICIS Ce NG an A A E E TEE 13 Foe D SUING CONS ene a a a 14 M ENANTO EA E E E E E E E seers eeeeesseeateaert 15 Walo ea E E E E E eee 15 REDNECK O VE E EE EEE E EE E E 15 Ae Toue NOONE siraan E E EE E EA 16 COMCEL S oare E A EE E S E E A E E E E E 17 Introduction Congratulations on the purchase of your new e bike We want to make you happy and believe your new e bike will bring you lots of fun We ask that you please read this manual thoroughly paying special attention to the safety warnings before you start riding your bicycle Please observe traffic regulations and do not lend your bicycle to anyone who is unfamiliar with it The bicycle can only be legally used on the road by a person aged 14 years and older We strongly advise you to always wear a bicycle helmet when using your e bike If you are un
7. erged in water e Please use caution Do not operate your bicycle under bad heavy weather conditions Replacement Key You will be supplied with two 2 keys for your bicycle Please keep the spare key in a safe place in case anything should happen to the one you regularly use In the event that you misplace damage or break both keys contact your dealer or call 855 888 1891 for a replacement 15 Simple Troubleshooting A Top speed too slow Fully recharge battery B Power on but motor not working 1 Reinstall battery Replace fuse C Driving shorter distance per recharge D The power and the indicator lights are all on with throttle or pedal assist but the e bike does not work E The power and the indicator lights are all on bike works with throttle but not with pedal assist F The power and the indicator lights are all on bike works with pedal assist but not with throttle G The power is on and the throttle is twisted but the bike does not work H The switch is turned on and the bike takes off without using the throttle After stopping the bike does not start when the throttle is twisted J You connect the power to the charger but the indicator light does not come on K You plug in the charger to the bike and the outlet and the green light comes on instead of the red light This means it not charging 1 Check tire pressures Recharge completely or have charger re inspected Replace w
8. familiar with cycling we suggest taking a cycle proficiency course prior to using your bicycle Before you ride your bike for the first time please make absolutely certain that it has been correctly assembled You can do this either by taking it to your nearest bicycle shop or if you are proficient in bicycle mechanics you can do the inspection yourself You must make certain that the pedals saddle handlebars and any self assembly items have been correctly fitted Test your brakes prior to using the bike every time you use it and remember the bike will not stop as quickly in wet or icy conditions as it would on a dry road Frequently check your tire pressures They should be 60 psi 4 1 bar Low tire pressures will result in damage to the tires and will massively reduce your range NEVER drink alcohol and ride your electric bike The use of alcohol greatly reduces reflexes and limits your ability to ride safely Even a very small amount of alcohol will limit your ability to be safe on the road When you need to replace your battery please either dispose of it properly or send it back to us or your retailer and we will make sure it is properly recycled Happy cycling Your friends at e JOE Bike Warranty LIMITED ONE 1 YEAR COMPONENTS WARRANTY Forks stem handlebar seat post saddle brakes cables bottom bracket crank set pedals chain rims spokes wheel hub freewheel cassette derailleur shifter motor throttle contr
9. he back folding Instructions The EPIK Lite can be folded for easy storage and travel Fold the pedal by pressing the lever on the pedal inward then upward Fold the stem by pressing the chrome releasing the lever outward Fold the frame at the middle by lifting the metal bar locking out of the frame This is how the bike looks when it is completely folded 14 Maintenance 1 IMPORTANT Do not attempt to open the casings of the battery motor or controller It could be dangerous and will void any warranties If you experience any problem please contact our service department or your retailer Wheel spokes should be adjusted every 300 miles of riding Handlebar and saddle tubes should never be raised beyond the maximum indicated by the safety lines around the tubes 4 Your bike has a rear derailleur that will automatically tighten your chain However if the chain becomes loose or frequently comes off the front cog you can easily adjust the chain tension by loosening the rear axle nuts slightly and adjusting the tension bolts Make sure that the chain runs freely and retighten the axle nuts 5 It is recommended that you take your bicycle for a tune up and maintenance check by a bicycle mechanic on a regular basis Water e Your electric bicycle is rain and splash proof and can be used in all weathers e The electric components of the vehicle such as the motor battery and controller MUST NOT be subm
10. ith a battery Controller needs to be replaced or Motor needs to be replaced Controller needs to be replaced or 2 Pedal assist module needs to be replaced or 3 Motor needs to be replaced Controller needs to be replaced or Throttle needs to be replaced or Motor needs to be replaced Check battery to see if it needs to be charged or 1 2 Fuse needs to be replaced or 3 4 Controller needs to be replaced or Motor needs to be replaced Check if the throttle is stuck in the on position Lubricate or replace the throttle if it is faulty Check whether the brake handles are fully released Check Solutions to Problems D E and F above Check whether there is electricity to the charger If you have a voltage meter you can check to see if the charger produces the correct current 1 2 Check to see if the batteries are fully charged Check whether the charger is plugged in properly to both the battery and the outlet 3 Check the voltage of the charger and battery 4 If zero voltage on the charger then it needs to be replaced oF If zero voltage from the battery then check the fuse If all above mentioned situations are normal then there is another problem Please call your local dealer or our service department for more assistance 16 Contact Us We thoroughly hope you enjoy your new e JOE bike If you have questions comments concerns
11. ke or releasing the throttle will automatically cut the power to the motor To get the furthest distance range it is recommended to pedal the bicycle with the Pedal Assist System mode ON When riding down hills do not turn off power otherwise the controller and motor will be easily damaged When riding your e bike when the battery power is low it is recommended to pedal your e bike as much as possible and charge the battery as soon as you get to an electrical outlet Turn off the power and remove the key while parking If you decide to push your bike for any reason make sure to turn the power off so you don t automatically turn the throttle on and make the electrical bicycle start suddenly and cause an accident To help get the best distance out of your electric bike refrain from unnecessary braking and coast as much as possible Using the Kickstand The EPIK Lite is equipped with a stabilizing kickstand that aims to support both sides of the bicycle Secure the Bicycle for Kickstand Maneuvering Place one hand on handlebar and the other on the seat to stabilize the bicycle Putting the Kickstand Down A Use foot to push the kickstand down until it reaches the Then push the bike backwards and Pon allow the kickstand ground and presses to move forward forward Use hand on seat Plant foot in front UF EA 2 l to propel the bike of the kickstand to 4 TN forward guiding hold it in place be T the kickstand Q towards t
12. lting from failure to follow instructions in the owner s manual acts of God accidents misuse neglect abuse commercial use modification or improper assembly e This warranty does not include covering normal wear and tear parts ex Tires tubes brake etc e This warranty does not cover parts damaged by an attempted repair unless performed by an authorized dealer of e JOE Bicycle with e JOE Bicycle s knowledge e e JOE Bicycle Inc reserves the right to refuse any warranty claim Opening Your Bicycle When receiving your bicycle your package should contain the following items e The main body of the electric bike consisting of O 30 2 O Frame Rear wheel Gear and chain V brake Battery Rear fender e The handlebar subassembly O This subassembly is still connected to the main body by the brake cables and electrical wires The brake levers and gear controls of the handlebar are already assembled Additionally the right handle also has an integrated control for the throttle power assisted mode and the left side has Power Assist Display with a battery charge level indicator e The seat or saddle which is attached to the pedestal stem e The front wheel with front brakes e The front wheel fender with supports e Front and rear reflector assembly lights are optional e Pedals 2 e Battery charger in a separate box e Mini tool kit for assembly and or repairs e Keys 2 Please contact your dealer o
13. oller wiring harness kick stand reflectors and hardware are warranted to be free from manufacture defects in materials and or workmanship for a 1 year period from the date of original purchase LIMITED ONE 1 YEAR BATTERY WARRANTY Lithium lon batteries are warranted to be free from manufacture defects in materials and or workmanship for a 1 year period from the date of original purchase cycle life or deep charge up to 70 full capacity LIMITED 30 DAYS FULL REPLACEMENT WARRANTY If an e JOE bicycle is not working properly because of a major defect within the first 30 days e JOE Bike Inc will repair or replace any defective e JOE Bicycle at its sole option and expense upon determining whether the damage failure or loss is due to a major defect e JOE Bicycle will have sole discretion to determine whether the damage failure or loss is due to a major defect or otherwise TERMS OF WARRANTY e This warranty only applies to the original owner of an e JOE Bicycle bike e Proof of purchase is required for all warranty claims e This warranty is for replacement parts ONLY and does NOT cover the cost of labor e This warranty covers shipping costs for dealers ONLY o If you believe your bicycle needs service or are experiencing problems with your bicycle e JOE Bicycle encourages you to bring your bike to your nearest electric bike dealer for warranty determination and assistance e This warranty does not cover any damages or defects resu
14. own in Fig 2 and the mark cannot be higher than tie in of seat cushion If used inappropriately serious damage may be caused to rider Angle of saddle In order to avoid the forward tilt when driving it is best to make slight upward tilt adjustments for the front end of the saddle Appropriate adjustment can be made for pre and post position according to personal height and it is suitable for the seat post to be in middle position generally Safety line Safety line The lowest height of the seat Move the quick release handle to OPEN Put the saddle to the lowest position until it cannot insert Then move the quick release handle to CLOSE This is the lowest height of seat The highest height of the seat Move the quick release handle to OPEN Put the saddle to the highest position but not more than the safe line Then move the quick release handle to CLOSE This is the highest height of seat Battery and Charger Indicators Battery Access Slot Make sure the battery is properly seated against its housing connector base Insert the lock key into the battery access slot on the outside frame underneath the bicycle Turn the key to remove lock the battery Removing Locking Battery Refer to Page 14 Folding Instructions Step 3 to fold the frame exposing the battery Bicycle Battery Charge Indicator Lights To see the battery levels use the charge indicator on the handlebar when all lights are lit up
15. r e JOE Bicycle if any of these parts are missing Structure of your new Electric Bicycle Currently electric bicycles can be divided into two classes TAG Twist And Go and PAS Pedal Assistance System The EPIK Lite belongs in the second classification Refer to the picture below for structure and parts Ring Derailleur lever Brake handle anp Seat post Folding pipe s4 Saddle post Rear Carrier Headlight Folding joint Rear mud guard Brake bl Front fork Motor Freewheel Derailleur Front whee Clank arm Front hub ear whe Chain Kickstand Rear wheel Rear motor g Main Specifications EPIK lite Weight 37 b Max Capacity 300 Ib Dimension 60 x 22 x 43 in Max speed 20 mph Full charge up to 30 mi distance N o Climbing grade lt 1 36V Battery capacity Rated efficiency 80 kWh 62mis1 2kWh 62mi Battery Type Lithium Polymer Voltage 36V Capacity 7Ah Charger Input voltage AC120V 60Hz Charging time 4 6 hr How to charge Direct charge Connect plug with plug receptacle Brakes There are two types of braking mechanisms that e JOE installs on its electronic bicycles the V brake and Disc brake The EPIK Lite has a V brake installed on the rear brake and is used to control the entire braking system of the bicycle as shown in the picture below Brake Precautions e Do not brake too strong or abruptly as it will mak
16. tery at least once per month Do NOT use your battery in a very low state e Itis normal for distance range to reduce as a result of low temperatures e While carrying the charger DO NOT bump drop or damage the charger or it may result in failure e Avoid any contact with water while charging your battery If a plug or socket becomes wet dry it completely before using it 11 General Operating Instructions Before You Ride for the First Time e Check that the handlebar and handlebar stem are properly tightened e Check all other nuts and bolts and fixings are properly tightened paying particular attention to the motor fixings kick stand yoke and steering head bearings e Check that brakes and brake levers are functioning properly e Check that tire pressures are 60 psi 4 1 bar and that tires are not damaged e Check that reflectors and lights are functioning properly e Make sure battery is fully charged e Load battery into bicycle and turn on by pressing the ON OFF button on the LED display e Check LED Electric Assist Display The lights should be illuminated on the left hand side of the handlebars if applicable o FULL full charge all LED lights are lit up o HALF half charge half LED bar o EMPTY no charge one LED bar please operate with pedals and charge as soon as possible Electric Assist LED Operating Instructions When you first turn on your electric bike your LED Electric Assist Display will automatically go into the
Download Pdf Manuals
Related Search