BT-6901 user manual V1.10
Contents
1. 2 Mode of Connection and Terminal Resistance 2 1 Industry standard of RS485 bus requires that connection mode of daisy chain should be used between the devices with 1200 terminal resistances connected at the both ends As shown in fig 26 and fig 27 is simplified connection but the distance of part D shall not beyond 7 meters Fig 26 Fig 27 2 2 1200 terminal resistance is connected as shown in fig 27 1200 terminal resistance is available in the circuit board and the connection is shown as following When needing to connect 1200 resistance toggle the 8 bit of DIP switch SW2 to ON This way the 1200 resistance is connected to the circuit AppendixIV Address Code Mapping Table SW1 DIP Switch sets the dome address which using binary encoded The 8th is the top bits and 1st is the lowest bits Toggle the code bits of DIP Switch to ON then the corresponding location is 1 Conversely it s 0 23 Following is a dome address code mapping table to set PELCO_D Switch Settings Address SW1 1 SW1 2 SW1 3 SW1 4 SW1 5 SW1 6 SW1 7 SW1 8 0 OFF OFF OFF OFF OFF OFF OFF OFF 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 8 OFF2. _SSYSTEM gt RR CAMERA LANGUAGE DISPLAY RESET EXIT fig 4 1 1 Get into the Menu Screen 4 2 System Information SYSTEM MFG PROTOCOL AUTO DOME ID 001 COMM 2400 N 1 VERSION EXIT Fig 4 2 1 MFG Max 15 characters display on the screen PROTOCOL Display the protocol of the dome 11 DOME 10 Display the dome address Form Baud rate Check bit Data bit Start bit VERSION Version will update along with the product upgrading Remark Protocol ID and COMM all can be set in menu lt COMM gt 4 3 Dome lt DOME gt lt COMM gt lt GUARD TOURS gt lt A B SCAN gt lt PAN SCAN gt lt PARK ACTION gt lt PRIVACY ZONE gt lt ALARM gt lt ADVANCED gt EXIT Fig 4 3 1 4 3 1 Communication lt gt lt gt DEVICE ID COMM RESET TO HARD DIP SET CHECK ID 0000 TARGET ID 001 SOFT PROTOCOL AUTO BAUD RATE 2400BPS lt COMM RESET gt SAVE YES EXIT EXIT Fig 4 3 1 1 Fig 4 3 1 2 DEVICE ID 12 It is only and used to distinct from the ID of other domes CHECK ID Distinguishing several domes with same ID and altering target ID soft protocol and baud rate need to enter check ID in line with the device ID otherwise altering can t be completed TARGET ID Target ID is available from 001 to 250 SOFT PROTOCOL Soft protocol is auto Pelco D and Pelco P available BAUD RATE 1200BPS 2400BPS 4800BPS
3. 9600BPS available COMM RESET As shown in fig 4 3 3 2 carry out YES to reboot the dome and communication reset to DIP set hard ID and hard baud rate SAVE Please save the change of communication After saving the dome will reboot Remark The out of factory default of dome camera is hardware DIP set After the COMM is changed in menu it can t be effective until saved If needing to get hardware DIP set again run the COMM RESET 4 3 2 Guard Tours GUARD TOURS GUARD TOUR 01 GUARD TOUR 01 ID POINT TIME S SPEED SETTING 1 01 06 64 INIT 2 02 06 64 RUNNING 3 03 06 64 DELETE 4 04 06 64 5 05 06 64 6 06 06 64 7 07 06 64 EXIT 8 08 06 64 Fig 4 3 2 1 Fig 4 3 2 2 GUARD TOUR Total 3 guard tours selectable 01 02 03 13 SETTING Each guard tour includes max 16 presets The number of the preset is from 0 64 0 is not valid dwell time is 1 to 60s selectable Speed is 1 to 64 grades selectable INIT After init preset point dwell time speed will resume to default setting RUNNING Running the present guard tour DELETE Delete the guard tour set After deleting the present preset points all display as 0 While the exact preset point information doesn t be deleted So it is convenient for user to select the preset point needing to be guarded tour 4 3 3 A B Scan lt A B SCAN gt A B SCAN PRESET A 01 RUNNING PRESET B 02 LEFT KEY TO EXIT SCAN SPEED 20 DWELL TIME 06S
4. RUNNING DELETE EXIT PAN XXX TILT XX Fig 4 3 3 1 Fig 4 3 3 2 PRESET A On A B scan A point can be preset from 0 to 64 PRESET B On A B scan B point can be preset from 0 to 64 SCAN SPEED A B scan speed is 1 to 64 grade selectable DWELL TIME Dwell time between A to B is 2s to 60s selectable RUNNING Running the A B scan Check Fig 4 3 4 2 DELETE 14 After deleted the preset points display as 0 While the exact preset point information doesn t be deleted So it is convenient for user to select the preset point needing to be scanned Speed and dwell time will reset as default setting 4 3 4 Pan Scan lt PAN SCAN gt PAN SCAN PAN SCAN SPEED 20 RUNNING INIT LEFT KEY TO EXIT RUNNING awe PAN XXX TILT XX Fig 4 3 4 1 Fig 4 3 4 2 PAN SCAN SPEED Pan scan speed is 1 to 64 grade selectable INIT Reset the scan speed and tilt degree as default setting RUNNING Running the scan speed and tilt degree set 4 3 5 Park Action lt PARK ACTION gt lt PARK ACTION gt PARK MODE OFF PARK TIME 01M SETTING RUNNING DELETE PRESET 1 SAVE EXIT PRESET 2 BACK Fig 4 3 5 1 Fig 4 3 5 2 PARK MODE Park mode includes OFF Park action A B scan Pan scan guard tour01 guard tour02 guard tour03 and Preserve action When park mode is OFF status the dome doesn t run park mode 15 When park mode is PRESERVE ACTION status it record previous action or
5. ALARM LINKAGE OFF ALARM 1 01 ALARM 2 02 ALARM 3 03 ALARM 4 04 EXIT Fig 4 3 7 1 ALARM Alarm has OFF and ON selectable PATROL TIME Patrol time is 2 605 selectable ALARM LINKAGE Alarm linkage has OFF and ON selectable ALARM 1 To run alarm 1 presets 1 64 are available ALARM 2 To run alarm 2 presets 1 64 are available ALARM 3 To run alarm 3 presets 1 64 are available ALARM 4 To run alarm 4 presets 1 64 are available 4 3 8 Advanced lt ADVANCED gt PWRONACTION MEMORY RATIO SPEED ON AUTO FLIP ON lt OTHERS gt EXIT Fig 4 3 8 1 PWR ON ACTION Power on action can be set as Memory A B scan Pan scan Park action Guard tour 01 Guard tour 02 Guard tour 03 and No action RATIO SPEED Ratio speed can be set as ON or OFF status AUTO FLIP Auto flip can be set as ON or OFF status OTHERS Set other options 4 4 Camera lt CAMERA gt CAM AUTO ZOOM SPEED QUICK DIGITAL ZOOM OFF FOCUS AUTO IRIS AUTO BLC OFF FREEZE OFF EXIT Fig 4 4 1 CAM Display the information of module supported by this dome ZOOM SPEED Zoom speed is quick and slow selectable DIGITAL ZOOM Digital zoom is on off selectable FOCUS Focus is auto and manual selectable IRIS Iris is auto and manual selectable BLC BLC is ON and OFF selectable FREEZE Video freeze is ON and OFF selectable Remark Only if those functions are available on the present module the user can use it 4 5 Lan
6. OFF OFF ON OFF OFF OFF OFF 9 ON OFF OFF ON OFF OFF OFF OFF 10 OFF ON OFF ON OFF OFF OFF OFF 11 ON ON OFF ON OFF OFF OFF OFF 12 OFF OFF ON ON OFF OFF OFF OFF 13 ON OFF ON ON OFF OFF OFF OFF 14 OFF ON ON ON OFF OFF OFF OFF 15 ON ON ON ON OFF OFF OFF OFF 16 OFF OFF OFF OFF ON OFF OFF OFF 17 ON OFF OFF OFF ON OFF OFF OFF 18 OFF ON OFF OFF ON OFF OFF OFF 19 ON ON OFF OFF ON OFF OFF OFF 20 OFF OFF ON OFF ON OFF OFF OFF 21 ON OFF ON OFF ON OFF OFF OFF 22 OFF ON ON OFF ON OFF OFF OFF 23 ON ON ON OFF ON OFF OFF OFF 24 OFF OFF OFF ON ON OFF OFF OFF 25 ON OFF OFF ON ON OFF OFF OFF 251 ON ON OFF ON ON ON ON ON 252 OFF OFF ON ON ON ON ON ON 253 ON OFF ON ON ON ON ON ON 254 OFF ON ON ON ON ON ON ON 24 Following is a dome address code mapping table to set PELCO_ P Switch Settings Address SW1 1 SW1 2 SW1 3 SW1 4 SW1 5 SW1 6 SW1 7 SW1 8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 4 ON ON OFF OFF OFF OFF OFF OFF 5 OFF OFF ON OFF OFF OFF OFF OFF 6 ON OFF ON OFF OFF OFF OFF OFF 7 OFF ON ON OFF OFF OFF OFF OFF 8 ON ON ON OFF OFF OFF OFF OFF 9 OFF OFF OFF ON OFF OFF OFF OFF 10 ON OFF OFF ON OFF OFF OFF OFF 11 OFF ON OFF ON OFF OFF OFF OFF 12 ON ON OFF ON OFF OFF OFF OFF 13 OFF OFF ON ON OFF OFF OFF OFF 14 ON OFF ON ON OFF OFF OF
7. dav 97 Guard tour 2 86 BLC on 98 Guard tour 1 87 BLC off 99 Pan scan Remark use some other equipments to control speed dome some special functions probably can t be effective because of the limite of protocol 3 4 Screen Character Operation Call preset 95 to enter the OSD call preset 94 to exit the OSD lt Up or Down Move the option of OSD change the value the OSD Right Enter the option select the item or confirm lt Left Return to main menu cancel Angle Display XXX XX pan XXX XX tilt lt COMM Display Display the dome ID and baud rate on the top left corner of the screen Remark 1 Items with gt mean they have sub menu 2 means the cursor selecting some option 3 means editing the content of some option selected 4 When entering the setting page in menu it is useless to call preset 94 to exit the menu directly Such as the submenu SET in menu GUARD TOUR SET 4 OSD Menu 4 1 Menu Index lt MAIN MENU lt SYSTEM gt lt DOME gt lt CAMERA gt lt LANGUAGE gt lt DISPLAY gt lt RESET gt EXIT 10 lt SYSTEM gt lt COMM gt DEVICE ID PROT
8. F OFF 15 OFF ON ON ON OFF OFF OFF OFF 16 ON ON ON ON OFF OFF OFF OFF 17 OFF OFF OFF OFF ON OFF OFF OFF 18 ON OFF OFF OFF ON OFF OFF OFF 19 OFF ON OFF OFF ON OFF OFF OFF 20 ON ON OFF OFF ON OFF OFF OFF 21 OFF OFF ON OFF ON OFF OFF OFF 22 ON OFF ON OFF ON OFF OFF OFF 23 OFF ON ON OFF ON OFF OFF OFF 24 ON ON ON OFF ON OFF OFF OFF 25 OFF OFF OFF ON ON OFF OFF OFF 26 ON OFF OFF ON ON OFF OFF OFF 251 ON OFF ON OFF ON ON ON ON 252 ON ON OFF ON ON ON ON ON 253 OFF OFF ON ON ON ON ON ON 254 ON OFF ON ON ON ON ON ON 255 OFF ON ON ON ON ON ON ON 256 ON ON ON ON ON ON ON ON 25 Appendix Exception Issue Possible Reason Solution After power is applied Cable harness is improperly Verify that the orientation of the connected connector input there is no action self test Input power voltage is too low Verify the voltage of the input power and no video image Power supply does not work Change a new power supply Self test is Wrong communication Set the correct protocol baud rate and normal but dome address of device settings cannot be controlled Improper connection of Verify the polarity of the RS485 connect control cable polarit as per the instruction manual Mechanical obstruction Verify and correct it Noise after self testing Camera module is not installed correct Change the correct power supply Low power Check the power supply or make sure t oe gt URS p t
9. Intelligent Speed Dome Camera User Manual WARNINGS AND CAUTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECTS THROUGH VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT CAUTION EXPLANATION OF GRAPHICAL SYMBOLS The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user the presence of non insulated dangerous voltage within the product s enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to different persons The exclamation point within an equilateral triangle is intended to alert the user the presence of important operating and maintenance servicing instructions in the literature accompanying this product PRECAUTIONS 1 Persons without technical qualifications should not attempt to operate this dome device before reading this manual thoroughly 2 Remove any power to the dome before attempting any operations or adjustments inside the dome cover to avoid potential damage to the mechanism 3 Inside the dome cover there are precision optical and electrical devices Heavy pressure shock and other sudden adjustments or operations should be avoided Otherwise you may cause irreparable damage to the product 4 Please DO NOT remove or disassemble any internal parts of the video camera to avoid normal operation and possibly void the warranty There are n
10. OCOL AUTO CHECK AD 0000 OME T 001 TARGET ID 001 COM 240 N 83 SOFT PROTOCOL AUTO VERSION BAUD RATE 2400BPS mE COMM RESET SAVE lt DOME gt EXIT lt GUARD TOURS gt lt COMM gt lt A B SCAN GUARD TOUR 01 lt GUARD TOURS gt PRESET 01 lt SETTING gt lt SCAN PRESET B 02 INIT lt PAN SCAN SCAN SPEED 20 RUNNING lt PARK ACTION DWELL TIME 065 DELETE PRIVACY ZONE gt RUNNING Ex lt gt ALAR DELETE lt ADVANCED gt ERE SCAN 1 GARE KETONE PAN SCAN SPEED 20 CAMERA PARK MODE OFF INIT PARK TIME 01M RUNNING CAM AUTO lt SETTING gt EXIT ZOOM SPEED QUICK RUNNING DIGITAL ZOOM OFF DELETE lt ALARM gt FOCUS Io EXIT IRIS AUTO ALARM OFF BLC OFF PATROL TIME 068 FREEZE OFF lt PRIVACY ZONE gt ALARM LINKAGE OFF EXIT MASK NO 01 ALARM 1 01 MASK OFF ALARM 2 02 lt LANGUAGE gt lt SETTING gt ALARM 3 03 LANGUAGE ENGLISH EXIT ALAS 8 ALARM 5 05 ADVANCED ALARM 6 06 EXIT DISPLASS PWR ON ACTION MEMORY b TT RATIO SPEED ON SYS DATA SYSTEM PAL fd AUTO FLIP ON P AND T ON CONFIRM lt OTHERS gt ACTION ON EXIT EXIT DOME ID ON COMM ON lt DOME RESTART gt lt CAM DATA gt Eat CONFIRM DN SRBSBES lt PRESET gt RESTARTS CONFIRM DEL ALL PRESETS SBYSDATA CONFIRMI DEL 01 TO 16 SOAMDATAS CONFIRM2 DEL 17 TO 32 SPRESBES CONFIRM3 DEL 33 TO 48 ERIT CONFIRM4 DEL 49 TO 96 EXIT lt MAIN MENU gt
11. all servicing to qualified service personnel Servicing is required when the device has been damaged in any way when liquid traces are present or the presence of loose objects is evident or if the device does not function properly or has received sever impact or has been dropped accidentally 11 Indoor dome is for indoor use only and not suitable for outdoor or high humidity locations Do not use this product under circumstances exceeding specified temperature and humidity ratings 12 Avoid pointing the camera directly to the sun or other extremely bright objects for prolonged period of time avoiding the risk of permanent damages to the imaging sensor 13 The attached instructions are for use by qualified personnel only To reduce the risks of electric shock do not perform any servicing other than contained in the operating instructions unless you are qualified to do so 14 During usage user should abide by all electrical safety standards and adhere to electrical specifications for the operation of the dome The control cable for RS485 communications as well as the video signal cables should be isolated from high voltage equipment and or high voltage cables 15 Use supplied power supply transformer only PROGUG 1 E MIU 1 VZ SP 2 1S E nmnetioripeseription emma SR REUS SUE DIE URNA 3 znstallauom EIE DIE IEEE IEEE EMEN 5 Swite
12. ch as neon lamp etc 4 Targets are behind the glass covered with water droplets or dust 5 6 Monotonous large area targets such as wall Targets are moving quickly 7 Targets are too dark or faint e BLC If a bright backlight is present the target in the picture may appear dark or as a silhouette BLC enhance the target in the center of the picture the dome uses the center of the pictures to adjust the iris if there is a bright light source outside this area it will wash out to white the camera will adjust the iris so that the target in the sensitive area will properly exposed e Iris Control Factory default is automatic camera aperture in mode of which camera senses changes in ambient light through moving and adjust automatically lens aperture to make the brightness of output image stable Users can through pressing OPEN or CLOSE iris adjusting keys manually adjust the aperture size to get the required picture brightness By controlling the keyboard up down left right or zoom to resume auto iris auto iris is recommended e Auto recognize to Protocol and Module The dome can auto recognize to the corresponding protocol and module during self inspection eg Module Sony CNB LG Samsung domestic etc Protocol PELCO P PELCO D etc e 3D Allocation With this function users can move the image of some area to the center of screen according to specified level and vertical coordinates and au
13. ction Lens zooms out to the widest angle From running the above actions to completing power up self testing finishes 3 2 Basic Function Dome Running Control joystick or up down left and right key in the keyboard Zoom Press ZOOM button to make the lens farther and minify the scene Press ZOOM button to make the lens closer and magnify the scene Focus After FOCUS button is pressed the object in vicinity will become clearer while the object far away will become ambiguous After FOCUS button is pressed the object far away will become clearer while the object in vicinity will be ambiguous e Iris Press IRIS to gradually shrink the iris and decrease the image brightness Press IRIS to enlarge the iris and increase the image brightness e Preset Point Setting preset press button preset Calling preset press button call number enter 8 Deleting preset press button clear number enter Remark Some preset points are used tentatively for special functions 3 3 Special Function The follow presets are predefined as special function please shot preset No enter to enable those functions PREST FUNCTION PRESET FUNCTION 33 Pan scan180 88 Ereeze on 34 Reset 89 Freeze off 79 Diqital zoom on 92 A B scan 80 Diqital zoom off 94 OSD off 81 Auto dav niaht 95 OSD on 82 Switch to niqht 96 Guard tour 3 83 Switch to
14. der A B scan Pan scan Guard tour 01 Guard tour 02 Guard tour 03 Example Running A B scan at first when the action stops unexpectedly it enters the park mode to continue to run A B scan PARK TIME Park time is 01 60 mins selectable SETTING After entering the OSD menu as 7 4 8 2 move to the desired position and save the settings RUNNING Running the park action if there is no setting system will remind of it Please set park action DELETE Delete the settings 4 3 6 Privacy Zone lt PRIVACY ZONE gt lt PRIVACY ZONE gt lt PRIVACY ZONE gt MASK NO 01 MASK OFF PRIVACY PROPOSED TO lt SETTING gt SEIN PRESET 1 SAVE EXIT Fig 4 3 6 1 Fig 4 3 6 2 Fig 4 3 6 3 MASK NO Mask No depends on the number of the module supported The selective range of Sony is from 1 to 24 MASK Mask has on and off selectable SETTING Set the specific parameter of present mask NO and call preset 1 to save the settings Direction operation Modify the coordinate of dome Zoom operation Modify the size of scenery Iris operation Modify the size of privacy zone Remark The mask size is better more than double the target size If needing to modify mask 16 NO 02 set it again If needing to stop it set mask to OFF status If the module doesn t support privacy mask the screen will display the interface as Fig 4 3 6 3 4 3 7 Alarm Optional ALARM ALARM OFF PATROL TIME 06S
15. guage LANGUAGE LANGUAGE ENGLISH EXIT Fig 4 5 1 LANGUAGE Language can be set as Chinese or English Default settings is English 4 6 Display lt DISPLAY gt SYSTEM PAL PAND T ON ACTION ON DOME ID ON COMM ON EXIT Fig 4 6 1 SYSTEM Video system includes NTSC and PAL N means NTSC and P means PAL PAND T On screen it displays the pan and tilt degree user can enable or disable it ACTION On the screen it displays the current action such as A B scan Call preset Save preset Call park action Pan scan etc User can enable or disable it DOME ID At the top left corner of screen it displays the dome ID User can enable or disable it COMM At the top left corner of screen it displays the dome communication information User can enable or disable it 20 4 7 Reset lt RESET gt lt DOME RESTART gt lt DOME RESTART gt lt SYS DATA gt CONFIRM Save data lt CAM DATA gt dome restart lt PRESET gt EXIT EXIT lt SYS DATA gt lt CAM DATA gt CONFIRM Factory default EXIT CONFIRM Factory default EXIT lt PRESET gt CONFIRM DEL ALL PRESETS CONFIRM Delete the presets information CONFIRM 1 DEL 01 TO 16 saved by the dome CONFIRM2 DEL 17 TO 32 CONFIRM 3 DEL 33 TO 48 CONFIRM 4 DEL 49 TO 96 EXIT 5 Auto Temperature Control This product has built in fan and heater which accordingly cool or hea
16. he power input is AC 24V stable Video cable is improperly connected Correct Verify the connection of the video cable Image is Camera is on manual focus Change to auto focus blurring The lens is dusted Clean the lens Power is too low Change the AC 24V Power supply Communication distance is Make sure the distance is in the Controlling the dome too long allowed range not smooth RS485 cable is not properly Make the RS485 is properly connected connected Too many domes connected Make sure the connected dome is in t allowed quantity 26 Copyright Statement This copyright is merely belong to the manufacturer Without permission please don t plagiarize or copy the contents of this book in any form or by any means The company follows the policy of continuous development Therefore the company reserves the right to modify or improve the products described in this manual without notice The content of manual is offered according to the current state Unless applicable law otherwise specified the company does not make any kind of clear or tacit reassurance about the accuracy reliability and contents of this manual The company reserves the right to revise or recoup this manual at any time without notice 27
17. iuliamdline us 26 ELE TEMG 27 Indicates the functions with default protocol it might not function by using other protocols ndicates the optional functions only with certain mode 1 Product Introduction 1 1 Package Contents High Speed dome 1pc Wall mount bracket 1pc Power supply 1pc Screws kits 1pc User manual 1pc 1 2 Specification Horizontal Rotation Speed 200 s Tilt Rotation Speed 100 s Horizontal Rotation Range 360 Tilt Rotation Range 93 Auto Flip Horizontal 180 Vertical 180 Ratio Speed Support PWR on Action Memory NOP A B scan 360 Home Tour 1 3 360 Scan Flip Range 0 93 selectable A B Scan User programmable A B Scan Speed 01 64 speed selectable A B Scan Dwell 2 60s selectable 360 Scan Speed 01 64 grades Dwell Preset 01 60s interval selectable Preset Points 220 Go to Preset Speed 01 64 grades selectable Guard Tours 3 groups 16 points group Park Action Mode A B scan 360 Home Tour 1 3 Save action Park Time 01 60mins selectable Park Action User programmable Communication Protocol Pelco D Pelco P Communication RS485 Bus Baud Rate 1200 2400 4800 9600bps Dome ID Dial ID on Dome 001 255 Soft ID in Menu 001 250 Privacy Mask Support only Sony 24pcs settable Alarm 6 Inputs and 2 output
18. lu Setting ISO 5 A re a E E E E 5 22 Address settings c Mc 6 AMS fale Sells re 6 2 BUS AVIALCIING 6 Zo COMME colit eedem dh didt 7 SM saria Hte TID DII EE 8 EE UM E I EE 8 8 9 3 4 ScreemGharacter Operation 9 FOSID Me a 10 AME Ude E EE 10 4 2 Systermiimformmationms 11 EEE re 12 4 3 5 ONDE S OUS dae ea tai TO 12 EG MOUS TTC 13 A43 S A B SCO E EE 14 dod ANES CO 15 0 TES 15 SENSE O Ime n EF 16 4 9 Alamo OU ON alll E yp sayay ES 17 4 S CW UNC is eects 18 Zu auod tU ERE E ED RR RD EUER DEDERE 18 ecuaciones euet 19 cece S S R 20 ER EN Rte a tS BED EON 21 5 Auto Temperature gu tens eee pu SURE sna E EUR UE SU ETRAS 21 VAD UES U O tac CENE 22 Appemglxsmlli leamnginamsparenii6 oxe rs 22 Appendix Common Knowledge on RS 485 23 Basic PPP AA Aa ya 23 2 Mode of Connection and Terminal Resistance 23 AppsndixlV Address Code Mapping DAMIEN 23 AppemgdixslliiExceptiom
19. o serviceable parts inside the camera 5 All electrical connections to the dome should be made in strict accordance with the attached labels and wiring instructions in this manual Failure to do so may damage the dome beyond repair and void the warranty 6 For outdoor installation especially in high places or poles it is highly recommended that the proper lightning arrestors and surge suppressors are installed before the dome is entered into service 7 Please do not use the product under circumstances where the limits exceed the maximum specified temperature humidity or power supply specifications IMPORTANT SAFEGUARDS 1 Read these instructions before attempting installation or operation of dome device 2 Keep these instructions for future reference 3 Heed all warnings and adhere to electrical specifications Follow all instructions 4 Clean only with non abrasive dry cotton cloth lint free and approved acrylic cleaners 5 Should the lens of the camera become dirty use special lens cleaning cloth and solution to properly clean it 6 Do not block any ventilation openings Install in accordance with manufacturer s instructions 7 Use only attachments or accessories specified by the manufacturer 8 Verify that the surface you are planning to use for attaching the dome can adequately support the weight of the device and mounting hardware 9 Protect this devices against lighting storms with proper power supplies 10 Refer
20. rong power grid When system is independently grounded grounding impedance should be less than 40 and cross sectional area of grounding conductor must be not less than 25 Video Arrester Comm LightingArrester Power Arrester I LJ vem Lighting Rod 45degree i Dome must under45degree i range Power ground wire is not more than 42 Steel Sheath s 7 Fig 25 Appendix II Clean Transparent Cover In order to assure a clear image of dome the under cover of dome should be cleaned regularly e Be careful when cleaning and hold the outer ring of under cover by hands to avoid directly touching with it Because the acid sweat of finger membrane may corrode the surface coating of under cover Hard tool scratching the under cover may lead to blurring the images of dome so that affecting image quality 22 e Please use a soft enough dry cloth or other alternatives to wipe internal and external surface e f dirt is serious user can use a mild detergent Any senior furniture cleaning products can be used to clean the under cover Appendix Common Knowledge on RS 485 Bus 1 Basic Feature of RS 485bus According to industry bus standard of RS 485 RS 485 bus is half duplex communication bus with the characteristic impedance of 1200 whose maximum load capacity is 32 payloads including the master device and the controlled device
21. s Optional OSD Menu Multiple Language P N customization Operating Temperature 40 60 Operating Humidity lt 95 Non Condensing Heater amp Blower Auto temperature control Waterproof IP66 Power AC DC15 28V lt 3A Lightning Protection Transient voltage 6000V Power Consumption lt 20W Compatible Camera SONY LG CNB SAMSUNG etc 1 3 Function Description e Super Communication Address baud rate and protocol could be changed both from Dip switch or from software e Multilanguage OSD Menu The language display on screen menu the available language is English etc User can set the function or parameter or check the related information through the OSD e Privacy Masking In the monitoring scope areas that users can t or aren t willing to make show in the screen of the monitor can be set as privacy protected area area masking such as area where customers enter the password in monitoring system of bank or some doorway e Alarming Set Details please refer to the OSD menu e Focus 3 The auto focus enables the camera to focus automatically to maintain clear image User can use manual focus to in special condition Under the following conditions camera will not auto focus on the camera target 1 Target is not the center of the screen 2 Attempting to view images that are far and near at the same time 3 Target is strongly lighted object su
22. t setting is 2400bps Baud rate 1200bps 2400bps 4800bps 9600bps selectable Reserved Baud Rate 2600bps 4800bp s 2400bps 1200bps cms E Reserved Resistance 2 1 4 RS 485 Bus Matching Resistance The 8 bit of DIP switch SW2 is to select the matching resistor To the control center in order to prevent the reflection and interference of RS 485 communication signal and other signals the parallel matching resistor is needed in the communication interface of dome camera at the end away from the control center DIP switch SW2 has a control switch of matching resistor That 8 bit micro switch turn to the ON state set as below means having connected the matching electricity to RS 485 bus Reserved Resistance Hi Resistance on 2 2 Connection Connection of RS485 Before connecting please turn off the power and read carefully the instructions of all connected devices power cable AC 24 50HZ connect to AC power voy connected to 5455 AJB tenminal 3 Function Instruction 3 1 Power Up Action lt SYSTEM gt lt SYSTEM gt MFG MFG PROTOCOL ATUO PROTOCOL ATUO DOME ID DOME ID COMM COMM VERSION VERSION DETECTING PAN XXX TILT XXX Power Up Self Testing Pan Tilt Camera Self test Completion Pan action Pan rotate in certain direction and stop in zero coordinate Tilt action Tilt rotate in certain direction and stop in zero coordinate Lens a
23. t specified as zero point When the dome is working the preset point is not accurate because of something caused by the operator User can make the dome automatically enable the zero alignment by operational order e Auto Flip In the manual tracking mode when a target goes directly beneath the dome the dome will automatically rotate 180 degree in horizontal direction to maintain continuity tracking When the dome flips the camera starts moving upward as long as you hold the joystick in the down position 2 Installation 2 1 DIP Switch Settings 2 1 1 Preparation Before installation make sure that the protocol baud rate and address code used by the product is fully consistent with the control system Corresponding DIP switch site can be seen below ID svi eee Dome Address Set ron snz wassssss OC Matching Resistance T Reserved Baud Rate Set Reserved 2 1 2 Address Settings DIP switch SW1 is the address settings of camera It is a 8 bit switch each switch corresponds with O or 1 in the Binary code OFF status means 0 while ON status means 1 ID SW1 Address Settings See illustration above Turn on the 1st and 3rd allocated to ON position and get the binary code 00000101 so the correspondence address is 5 Detailed settings please refer to the back Address Code Mapping Table appendix IV 2 1 3 Baud Rate Settings The 4th and 5th DIP Switches set the Baud rate Factory defaul
24. t through temperature sensitive circuit inside the dome 21 Appendix Anti lightning Anti surge This product is extremely air discharge and lightning protection with TVS tube technology which can effectively prevent the transient lightning below voltage 3000V surge and damages caused by other types of pulse signals However necessary protective measures should be made in the premise of ensuring electrical safety for outdoor installation according to the actual situation Signal transmission line must be at least 50 meters far away from the high voltage equipment or high voltage cable Try to choose outdoor wiring laid down along the roof line Way of sealed steel pipe buried wiring is used in the area which opened and steel pipe units grounded in one point Overhead wiring is absolutely prohibited In the strong thunderstorms area or areas with high induced voltage such as high voltage substations measure of installation of additional high power lightning protection equipment and lightning rod must be taken Lightning protection and grounding of outdoor devices and lines must take the lightning protection requirements of buildings into consideration and comply with the related national standards and industry standards System must be equipotential grounding Grounding device must meet dual requirements of anti interference and electrical safety and should not be shorted or mixed with the adjacent lines in the st
25. to control to zoom according to zoom parameter set Day Night Switch With auto day night switch function when the illumination is low the picture will auto switch from day to night mode and when the illumination is high enough the picture will auto switch from night to day mode Ratio Speed Intelligent pan and tilt speed is variable depend on the zoom factor When zooming in the speed will become slower and when zooming out the speed will become quicker 4 e A B Scan Dome circularly scan close up real time scene according to A B points at setting speed in both horizontal and vertical directions e Pan Scan Dome 360 clockwise continuous scan the display scene at setting speed in horizontal direction under the condition that pitch angle remains the same e Preset After the dome camera keeps arbitrary PTZ location it will automatically move to the defined position when preset is called e Guard Tour Scan Dome patrol scans according to certain edited preset order e Power Off Memory This feature allows the dome to resume its previous preset or status after power is restored By default setting the dome support power up memory which improves the reliability and avoids repeated settings of the parameter e Park Action If users don t operate the dome in set time it will automatically run preset specific mode pan scan A B scan park action cruise preserve action etc e Zero Alignment There is a poin
Download Pdf Manuals
Related Search