Manual - Fire Systems Ltd
Contents
1. WIRELESS 54 Wireless Lighting Tool SRC 4001 SK User Manual wireless54 Contact Address www wireless54 de Manual No 5A4xxx Version 1 0 12 10 2014 Version 1 0 1 1 Product Information The easy to use tool SRC 4001 is offering priceless support during project planning of Detectomat wireless fire control panels SRC 3000 and SRC 4000 systems Damping in relevant radio frequences like 433 MHz and 868 MHz will be identyfied and evaluation of on site conditions will be simplified With the information given you can allocate the ideal location for your wireless control panel Additionally and in advance potential disturbances like extrinsic radio on operating frequnces of the Detectomat wireless control panel will be detected The wireless lighting tool SRC 4001 SK consisting of 2 field meter transmitter and receiver Operating frequencies 433 MHz and 868 MHz are adjustable according to the the installed system One of the two devices will be defined by the operator as transmitter and positioned at the place of installation of the radio control panel or at the repeater The second field meter will be used as receiver With changing of location on site building object respectively metering of signal strenght at the receiver will be possible due to constant sending of the transmitter The wireless lighting tool SRC 4004 SK is to initially estimate the realisation and extent of the wireless control panel only During imp2. ange between operating frequency 433MHz or 868MHz of the wireless fire control system SRC 3000 and SRC 4000 433MHz D Operating frequency of the SRC 3000 FCP 433 420 MHz bandwith 600 kHz sem DD Operating frequency of the SRC 4000 FCP IBN frequency 869 263 MHz bandwith 600 kHz LED Display Signalstrength The LED Display is divided in 8 LEDs of different colour 42e08 3 of the LEDs below from 90 to 110 dB are coloured in red h4AdE Sadb 3 of the LED in the center from 54 to 78 dB are coloured yellow soe 2 of the LED s above from 42 to 30dB are coloured green sop Damping of 90 dB max only corresponding to a display of 3 active signalstrength LEDs A frictionless communication of the wireless fire control systems SRC 3000 and SRC 4000 is no longer guaranteed if damping is increased according to 2 or less active singal strength LEDs Output increase or decrease 10008 110095 intermittently when transmitting LEDs indicating the signalstrength 1 2 Operation a For planning and setting of a wireless fire control panel it is quite helpful to know if additional RF signals potential radio interference are existing within the installation The SRC 40001 SK is as a rough indication for Activate one device of the field intensity meter as Receiver Ideally there is none or just a low indication of RF signals in the installation area of the wireless fire control system b Type o
3. f Antennae According to the planned type of wireless fire control panel a short or long type of the antenna is given Please use the long antenna fort he SRC 4000 FCP System and the short one fort he SRC 3000 c Switch On Switch On field intensity meter via key TX RX Press TX RX Taste and activate both devices d Select working frequency via key Band Select 868 MHz for the SRC 4000 FCP System and 433 MHz for the SRC 3000 system e The devices will be defined by the operator Press key TX RX for transmitter or receiver Change of function via key TX RX Taste f The transmitter will be positioned vertically on the master within an object e g assembly area of the wirels fire control panel or assembly area of the wireless repeater 0 3m distance max Version 1 0 3 g The receiver will be positioned vertically nearby the planned assembly area of the wireless component Subsequently the signal to signalstrength will be read every second Changing the position within the object the best possible position of the wirless components will be defined by the operator h Reading only at max damping of the measuring section e g with closed doors i The more LEDs flash every second at the receiver the stronger the receiving RF signal Empf nger A sufficient signalstrenght is given with signalling of 3 LEDs 90dB j If signalling is less than 3 LEDs 90dB adjust the position of the components or use a wireless repeater
4. lementing of the wireless systems all Detectomat wireless fire control systems are measuring independent the signal strenghts between the components The measured data are more accurate and basis for the actual realisation of the wireless installation 1 1 operating and display area The operating and display area of the wireless lighing tool SRC 4001 K is on both field intensity meter identical Each device can be used either as transmitter or receiver The oprating and display area are sectioned as following mentioned SRC 4000 SK er SJ 1 Switching On Off Setting of Transmitter Receiver 30dB TX RX Q p ee 42dB 2 Display of transmitting or receiving functionder san 2O a Ea 3 Selection of frequency band Receive R O 66dB 4 Display of activated frequency band 78dB 5 Display of receiving or transmitting signal B0dB strenght 43amHz O 1004B ssemHz 110dB Jo detectomat Version 1 0 2 The display and operating area of the wireless lighting tool SRC 4001 SK is equipped with 2 switch keys und 12 LEDs Labelling Colour Specification Switch On field intensity meter via key TX RX Press TX RX Taste and activate the device Press the key for approx 2 seconds to Switch Off the device Transmit O Press key TX RX to change function Transmitting and Receiving of the corresponding field intensitiy meter The Receive D LED indicates the corresponding operational mode Press key Band to ch
5. to increase the signal range k For the use and positioning of wireless repeater it is essential to consider a power supply of 230V AC Please note cascading of the wireless repeater is possible when using the wireless fire control system SRC 4000 FCP 1 1 1 Additional Function Specification Automatic Switch Off Within 10 min Noise Level Meter Additional frequencies will fade down expect working frequncy of the SRC 3000 and SRC 4000 1 1 2 Accessories Specification Antennae 2 different types according to working frequency 433 MHz or 868 MHz mountable Spare Battery Battery Type CR2450 Carrying Strap 2 Technical Data Item Number 32820 Extension 2 Field Intensity Meter 2 Antennae Spare Battery Working Frequency 433 920 MHz for the SRC 3000 System 869 263 MHz for the SRC 4000 FCP System Power Supply Battery Type CR2450 3V 20mA Transmitting Power 3 mW 3dB bandwith 400kHz Temperature Ambient temperature of 5 to 40 C storage temperature of 20 to 60 C without battery Admissible ambient air humidity Max 95 non condensing Material ABS PC Weight 180 g Dimensions H x B x T 80 mmx51 mmx 24 mm Version 1 0 4
Download Pdf Manuals
Related Search