SmartRG SR552n Quick Start Guide
Contents
1. Smart SRoo2n This Quick Start Guide shows you how to set up and begin using your new Gateway LED INDICAIORS EEEN The LEDs on the front panel of the unit can assist you in better understanding the current state of your modem POWER WAN LAN 1 4 WLAN WPS DSL 1or2 INTERNET DSL sync in progress On Off Blinking active INSTALLATION Connect one end of the supplied DSL cable to the port labeled DSL on the gateway Connect the other end of the supplied DSL cable to the DSL wall jack installed by your provider For all other devices connect the end of the Ethernet cable from that device into any of the LAN ports on the gateway Connect the power cord into the wall outlet and into the power jack on the back of the gateway For additional protection connect the power cord into a surge protector Turn on the unit by pressing the power button on the side of the gateway Your gateway is automatically being set up to connect to the Internet This process may take a few minutes to complete before you begin using your internet applications browser email etc If you are unable to connect to the Internet confirm all cable connections and ensure that the router s power is turned on INSTALLATION For bonded operation connect w the second pair T 5 min QUICK GATEWAY CONFIGURATION Logging in to your Gateway In order to change the settings on your gateway you must first login Ensure that you have2. available for WiFi setup Complete these first three steps then the remaining steps for the specific method you desire 1 From the left navigation bar click Wireless Basic 2 Check the Enable Wireless checkbox 3 If desired customize the SSID field to whatever network name you wish to have your client devices connect to Wireless Basic figure basic features of the wireless LAN interface You can LAN interface hide the network from active scans set the known as SSID and restrict the channel set based on This page allows y enable or disable wireless network Click Ap ave to configure the basic wireless options W Enable Wireless Enable Wireless Hotspot2 0 WPA2 is required _ Hide Access Point Clients Isolation Disable WMM Advertise Enable Wireless Multicast Forwarding SSID SmartRG0001 BSSID 02 10 18 01 00 03 Country Max Clients 16 QUICK GATEWAY CONFIGURATION WPS Method If the device you wish to connect to the internet via your SmartRG gateway supports WPS secure WiFi connection method you may follow these steps 1 From the left navigation bar click Wireless Security 2 Select the drop down menu Enable WPS Click the Apply Save button to commit your selection 3 On the right side of the gateway s enclosure press the button labeled WPS 4 Within 2 minutes activate WPS on your 3rd party device you wish to connect It may have a physical pushbutton on it s e
3. completed the above physical installation steps before you begin Open your internet browser application and type 192 168 1 1 into the address line e008 y SmartRG x LOGIN CONTACT US Search ws HOME amom ICTS yT Pa m a ABOUT US QUICK GATEWAY CONFIGURATION The following screen appears Wait while the Gateway automatically connects to your service provider AA JAS t RN a A pnd A A A a a VC a a Network status When the connection is complete OK will appear in green letters next to the Network icon Click the Manage gateway advanced link in the upper right The login dialogue will appear QUICK GATEWAY CONFIGURATION POO ey You may login with the factory default credentials Network status shown below x Authentication Required The server http 192 168 1 1 80 requires a username and password The server says Broadband Router User Name admin UserName sar Password Password admin Click the Log In button in the lower right Note In some cases your service provider has other settings Please contact your provider for logon informa Manual Configuration of the WAN In the event that the automatic connect process is unsuccessful refer to the Advanced Setup gt Layer 2 Interface and WAN Services sections of the User Manual for this gateway to manually establish a connection QUICK GATEWAY CONFIGURATION WiFi Setup Two methods are
4. r instructions please contact SmartRG support at support smartrg com or contact your SmartRG Sales Engineer www smartrg com SmartRG 501 SE Columbia Shores Blvd Suite 500 Vancouver WA 98661 USA SmartRG Inc All Rights Reserved Copyright 2014 v1 0 6 2014 RECORD YOUR SR552n WiFi SETTINGS Smart Preset wireless settings on your router WiFi network name SSID Network key password S L Ifyou change the preset wireless settings WiFi network name SSID Network key password LLL
5. xterior or possibly a software interface is used to Initiate WPS connection To learn how to use the WPS feature on your client device refer to its documenta tion Your device should now be connected to your router wirelessly using WPS If you encounter problems with the WPS setup such as Connection Failure Your client device failed to connect to the network Refer back to your client device for further instructions QUICK GATEWAY CONFIGURATION Manual Method Set up your Gateway s parameters first then 1 From the left navigation bar select Wireless Security and scroll down to the Manual Setup AP section 2 If your gateway supports multiple wireless networks select the SSID of the network you wish to configure 3 Select your desired Network Authentication from the drop down menu Ensure that the host devices you intend to use support your chosen authentication type 4 Choose a WPA Passphrase and type it in to this field You ll need this later when setting up your client devices 5 Select any desired encryption preferences in the lower three fields 6 Click Apply Save 7 Follow the WiFi connection instructions provided with your client device s to connect to the Router When browsing for available networks remember the SSID name you established in Step 2 Enter the passphrase in the appropriate location at the setup network setup screen of your WiFi client device ADDITIONAL SUPPORT If you require furthe
Download Pdf Manuals
Related Search