USER`S MANUAL
Contents
1. The offset can be entered in 0 01 mm or 0 01 inch increments The entered value may be rounded up depending on the step size Outputs a frame to facilitate weeding of the media This function eliminates the need to create a frame for weeding data When selected the frame is output to the plotter together with the figure being output The Frame is output to enclose the range specified in Data Size CAUTION This Frame is output using the Default Settings settings in the Cut Specification window Specifies the media feed Selecting From the Start Point feeds the specified length from the top of the plot range Selecting From the End Point feeds the specified length from the bottom of the plot range CAUTION With a grit rolling plotter in sheet media mode or with a flatbed plotter the plotter will return to View mode after output when Feed medium is set Tiled output is used to distribute the output of large data that exceed the media size over several pages If tiled output is selected the plot range is used as the page size Figures outside the plot range are output to the next page Page breaks correspond to the physical separations between media sheets A Page 1 Dotted line section is cut Unless the overlap width is set to 0 the pages overlap by a specified amount when output This is useful when aligning overlapping sections to assemble tiled output dE Matrix2. DXF Load from the File menu In the Open window select the desired file and click the Open button lt Single stroke sorting gt To run a single stroke sort select None Layer Color or All from Sort under the Output menu TIP Single stroke sorting refers to outputting objects such as line segments or arcs with start or finish points identical or very close to those of other objects thereby linking these objects Objects linked in this way are called single stroke groups lt Outputting data gt To output cutting data select Output to Plotter under the Output menu In the Output window select the driver for the current plotter via Output in Output Settings Then press the Output button to output the data lt Saving data gt To save data select Save As from the File menu Enter the file name in the Save As window and press the Save button 8 4 Operations lt Listing data imported gt Select Thumbnail View under the File menu to display the Thumbnails window Select a folder in the tree view window on the left hand side to display any files in the folder that can be opened on the right hand side as thumbnails Double click the image to be opened Expand the sub window at the bottom of the tree window to see a preview of the selected image lt Objects to be excluded from output to be deleted gt Objects to be excluded from output to be deleted can be excluded by
3. change without notice The utmost care has been taken in preparing this manual and the product itself If you find any ambiguities or errors please contact Graphtec or your retailer Please note that Graphtec will not be held liable for any consequences resulting from use of this manual or product regardless of any statements made above CONTENTS 1 Introduction fe IW e ee ee EE 4 T2 TESAUINGS S258 exces cto nana este eet A a a E A AEA EEs 4 13 System Re UE 5 TA Eeer 6 2 Setup 2 1 Installing the Graphtec Windows Plotter Ddriver cccceceeeeeeeeeeeeeeeeeeeneeeeeeseneeeees 7 2 2 Installing D Gut Maste r eut edc cates SNE SEENEN eg 7 2 3 Setting up the cutting en 7 SB BASIC OPERATIONS cite a ed ed uae creel dl decnn tes 8 ele 9 5 Window Details GEN EE ER 11 5 2 OUTPUT MMIC OW eege EE 12 5 3 Edit Media Size Windows iinicci ssscdcieeniecasiataaidedacot adhe eines EES EE 16 5 4 Cut Simulation window faci co shied ee eege AON E Ee ee 17 5 5 Preview WING OW EE 20 5 6 Cut Specification HEEN ee 21 5 7 Edit Media List lee e EE 22 5 8 Condition Erde Eine EE 23 5 9 Add Media to List WINdOW EE 24 5210 SOM Settings WNdOW sisa elisa leds haem ahleg a are a rE aN a Ea tildes 25 6 Error Messages 6 1 EEEE Re LEE 27 6 2 Media Size related eors 28 6 3 e e EE TC 29 6 4 Media related errors ccccccccseecccceeeeeeeceaeeseeceaseneeteceeeeasaneaeeesanenseesaneaeeseneaaeesensageees 30 1 Introduct
4. one of two methods 1 Select Settings under the Output menu Deselect the checkboxes in the layer and color lists in the Cut Specification window Deselecting the checkboxes removes objects by layer or color from the list of objects to be output 2 Click to select the object to be excluded in the view window and select Delete under the Edit window You can restore deleted objects using Undo All under the Edit window even after changes deletions have been saved lt Selecting multiple objects gt Select multiple objects by dragging with the left mouse button and enclosing the objects in a rectangle lt Adding objects to those selected gt Add objects to the group of objects already selected by clicking with the mouse while holding down the Ctrl key lt Selecting a one stroke group gt Select one stroke groups by selecting Select Group from the Edit menu and clicking the object This action selects the entire group to which the clicked object belongs lt Restoring deleted data gt If the checkbox under the Cut Specification window is deselected select the checkbox under the Cut Specification window If the object was deleted using the Delete command on the Edit menu you can restore all deleted objects by selecting Undo All under the Edit window You can also use the Undo and Redo commands on the Edit menu as long as the data has not been re sorted lt Enlarging the specified area gt To e
5. to 16 Selecting Use Data specified Size outputs the size required for output based on the Data Size setting Valid Area displays the current area with units in mm or inches COPIES cn ee Specifies the number of copies of the same data in the range from 1 to 999 Edit Media Size button Displays the Edit Media Size window for editing the media size list See 5 3 Layout Displays the layout for all data to be output including the plot range black border overlap width trimming blue border and data area red border Output button Outputs data If the Output button and output destination are grayed out the Graphtec driver has not been installed Install the plotter driver for the plotter being used Close button Saves settings and closes the window Confirm button Displays the Cut Simulation window See 5 4 to allow inspection or changes in the cutting sequence before output Preview button Displays the Preview window See 5 5 to display details of the output results Help button Displays Help information in the Output window Scaling s4 0 44 eraisicaniane Specifies data scaling in the range from 1 to 400 os eee Cut Frame Weed Border Feed Medium 0 000 Rotates the data for output Specify one of None 90 180 270 This setting specifies a value for offset thereby changing the object output position
6. Copy When multiple pages are output multiple black plot range borders are shown in the Preview window displayed when the Preview button is pressed The plot ranges are shown overlapping by the specified amount except when the overlap width is set to 0 CAUTION Parts adjoining the page are cut with straight lines to the data size width and length range enclosing the trimming border if trimming is specified For multiple page output output starts from the page containing the origin point then proceeds upward in the preview window If there are additional pages to the right the entire column containing the print origin is output before right hand pages are output from the bottom upward Straight lines on sections of adjoining pages are output based on the Default Setting settings in the Cut Specification window The tiled output function cannot be used with the matrix copy function The tiled output function cannot be used when Use Data specified Size is selected for media size 1 Specify page Specifies the output page range when outputting multiple pages by tiled output TIP Leave the last page blank to ensure that the final tile page is output 2 Overlap Specifies the amount of overlap output for adjoining pages when tiled output is selected The overlap can be specified in 1 mm or 0 01 inch increments Specifies output of multiple copies of the same data on the same sheet of media When
7. GRAPHTEC IP5639 4 D Cut Master USER S MANUAL GRAPHTEC Software License Agreement Graphtec Corporation Graphtec grants the user permission to use the software the software provided in accordance with these stipulations for use under the following terms Use of the software is deemed to indicate that the user consents to these terms and conditions 1 Copyright All copyrights to information contained in the software or in documentation such as manuals provided with the software are the property of the respective individuals or organizations indicated in the software or related documentation Usage rights The user may use the software on a single computer at any one time Copying and modification 1 The user may copy the software for backup purposes In this case the user must indicate the copyrights that apply to the software on the copied version 2 The user may not attempt to alter combine modify or adapt the software in any way including reverse engineering or reverse compiling Use by a third party The user may not grant reuse rights transfer reallocate or otherwise relinquish the software or user rights to a third party Warranty 1 Ifthe software does not function as specified due to reasons involving physical defects in the storage medium on which the software is provided please contact the dealer from whom the software was purchased A replacement copy will be provided fre
8. ains an invalid character Rename the medium A media size with the name lt lt Media name gt gt already exists This name is already in use Rename the medium 28 6 3 Output related errors Initialization of settings required for output failed Initialization of the parameters for output failed Check the parameter settings and free memory capacity Exceeds plot range The data exceeds the plot range Check the plot range Insufficient working memory The memory required for this task is unavailable Close other windows to free up memory capacity Plotter initialization failed Output not possible The plotter driver for the output destination cannot be used Check the connection Plotter output failed Plotter output failed Check the plotter connection 29 6 4 Media related errors Unable to add lt lt Media name gt gt to list Attempt to copy file from the DefSettings folder to the Settings folder failed Check that there is sufficient free disk space and that the Settings folder is not write protected Unable to save lt lt Media name gt gt Attempt to write the settings file failed Check to make sure that the Settings folder is not write protected A setting with the same name already exists A setting with the same name already exists Rename the medium Unable to delete lt lt Media name gt gt File deletion failed Check that the file or Settings folder is not write protected Unable
9. bject Group selection When using group selection specifying an object in the window selects the group of objects including the object specified rather than the individual object A group refers to a collection of objects such as line segments and arcs joined together and output zez zl entity Group 1 9 Here at shows the group currently displayed and the total number of groups Use the Top menu or press the Ee button to move the output sequence of the group selected to the top Use the Bottom menu or press the Cl button to move the output sequence of the group selected to the bottom Use the Forward menu or press the BW button to move the output sequence of the group selected one step forward ae ee Use the Back menu or press the button to move the output sequence of the group selected one step back Use the Reverse menu or press the button to reverse the output sequence of the objects within the group selected Use the Divide menu or press the gt button to divide the output of the objects within the group selected Note that divided output is not possible when polyline objects are selected Use the Convert menu or press the al button when polyline objects are selected to convert polylines to line segments and arcs thereby allowing divided output Only polyline objects can be converted Note that objects cannot be returned to their original state once converted Object selection When usi
10. ble will also vary depending on the plotter type Setting 0 disables this setting the cutting force will be that used for the condition number specified above Quality EE Specifies the acceleration rate for the pen when cutting or plotting Lower values correspond to higher quality This setting is effective only when specified with Force Quality settings range from 0 to 10 but the optimum setting will vary depending on the medium and pen type The settings available will also vary depending on the plotter type Setting 0 disables this setting the quality will be that for the condition number specified above CAUTION When setting Speed Force or Quality note that the settings also affect output conditions for other layers having the same condition number even if speed cutting force and quality have not been specified individually for these layers To enable this setting at the plotter the plotter condition setting priority must be set to Command or Program 93 5 9 Add Media to List window This loads a medium from the default settings list The default settings list is saved in the DefSettings folder in the folder in which D Cut Master is installed Add button 0 Adds the currently selected medium to the media edit list If a medium with the same name already exists Setting with same name already exists is displayed In this case rename the medium J4 5 10 Sort Settings window Specifie
11. e values The unit can be specified as mm or inch Adds text to the data to be output 1 Header Adds the specified text immediately after the Initialize command 2 Footer Adds the specified text immediately in front of the End command CAUTION To output ETX End of Text code 03H enter the values after V 003 Enter 3 digits in octal base 8 notation 3 digits must be entered x03 Enter 2 digits in hexadecimal base 16 notation 2 digits must be entered To output in the text enter W Sets the color used to indicate that objects or single stroke groups have been selected 11 5 2 Output window The Output window is used to set output settings You can also display the Preview window to inspect output data and the Cut Simulation window to inspect or modify the cutting sequence Output EE Displays the Graphtec plotter driver and port used by the system Output is directed to the driver port selected here Data Size jouc0 5 nsacdedeisanties Specifies the range required for output 1 Media Size Outputs the data plot range as data size 2 Object Area Outputs the range containing the objects to be output as data size Media Size Valid Area Specifies the media size to be used for data output The sizes available are User specified Sizes to 16 and Use Data specified Size Use the Edit Media Size button to edit the name and size of User specified Sizes 1
12. e of charge in the case that Graphtec is to blame for the physical defects 2 Inthe case of replacement mentioned in the clause above Graphtec provides a warranty only for the storage medium on which the software is provided 3 Graphtec provides the software as is Graphtec and its suppliers make no warranty with respect to the performance of this software or results obtainable from use thereof or the documentation Additionally Graphtec and its suppliers make no warranty explicit or implied with respect to infringement of third party rights commercial integrity or suitability for specific purposes Graphtec and its suppliers will not be held liable for any incidental derivative or special damages resulting from use of this software or documentation under any circumstances Graphtec and its suppliers will not be held liable even if notified by retailers of potential damages arising from use of this software or documentation Graphtec is not liable for any claims submitted by third parties Registered trademarks The company and product names occurring in this manual are the trademarks or registered trademarks of their respective companies Graphtec Corporation retains all copyrights to the D Cut Master software and this manual General precautions The contents of this manual may not be copied or reproduced in any form either in part or in whole The contents of this manual and product specifications are subject to
13. edia editing New button Displays the Condition Settings window See 5 8 for creating a new medium listing Copy button Copies the settings for the currently selected medium and displays the Condition Settings window Modify button Displays the Condition Settings window for changing the settings for the currently selected medium Delete button Deletes the currently selected medium Load button 00 002 Displays the Add Media to List window See 5 9 used to add a medium from the Default Settings list II 5 8 Condition Settings window Sets the cutting conditions Media Name Edits and displays the medium name Condition Number Specifies a plotter condition number between and 8 Numbers 5 to 8 may be invalid for certain plotters even if selected ho LEE Specifies the pen travel speed across the surface of the medium when cutting or plotting Valid speed settings range from 0 to 100 but the optimum speed will vary depending on the medium and pen type The settings available will also vary depending on the plotter type Setting 0 disables this setting the speed will be that used for the condition number specified above LE Specifies the pen force when cutting or plotting This setting is only effective when specified with Quality The force can be specified from 0 to 100 but the optimum setting will vary depending on the medium and pen type The settings availa
14. ion 1 1 Introduction D Cut Master can load DXF files created in AutoCAD R13 and display delete or sort data alter output sequences set the output or save data It also creates GP GL plot data for output via a Graphtec plotter driver 1 2 Features Permits output of separate layers colors Different output conditions may be set for each layer name or color Provides a sorting function to minimize media movement Allows automatic output of the cutting medium weeding frame i e a frame to facilitate weeding with the Cut Frame function Tiled output can be used to output figures onto multiple pages if they exceed the plotter s plot range Allows output conditions to be managed with media names A matrix copy function allows multiple data copies to be output to the same medium The cutting simulation function enables checking and modification of the cutting sequence Objects can also be divided for more detailed cutting 1 3 System requirements Minimum system requirements Os Windows 2000 Windows XP Windows Vista CPU Pentium III 600 MHz or higher Memory minimum 128 MB or more at least 256 MB recommended Monitor Must be capable of 1024 x 768 High Color display True Color recommended CD ROM drive Sufficient disk space for data storage Mouse Please refer to the README TXT file for the Graphtec plotters that can be used with D Cut Master When using Windows 2000 or Windows XP Full access
15. ly divides line segments thereby allowing over cutting to be avoided Note however that divided cutting is not possible when polyline objects are selected CAUTION The cut lines may not line up at the points where they were divided depending on the material used Displaying arrows Arrows can be displayed at the object end points by selecting Display arrows in the menu This makes it easy to determine the object cutting directions TIP Select a group while the simulation is halted 7 After checking the output sequence use the Output menu or press the al button to start output and close the Cut Simulation window Use the Return menu or press the D button to return to the Output window 19 5 5 Preview window The preview window displays page numbers and an image showing how the various items set will be look when output including offset position trimming position light blue line page breaks gray line and the matrix copy spacing set in the Output window The menu provides the following items Procedure 1 To display all data press the E button This displays all data adjusted to fit in the current window Press the DU button to display data at twice the current size Press the CH button to display data at half the current size 2 After checking the output results use the Output menu or press the al button to start output and close the Preview window Use the Return menu o
16. matrix copy is selected data is output in x columns to the right and y rows going up DER Horizontal and vertical spacing can be specified separately CAUTION The matrix copy function cannot be used with tiled output l Vertically Specifies the number of rows to be copied vertically Horizontally Specifies the number of columns to be copied horizontally Vertical Margin Specifies the spacing between rows in 0 01 mm or 0 01 inch increments The value entered here may be rounded up depending on the step size Horizontal Margin Specifies the spacing between columns in 0 01 mm or 0 01 inch increments The value entered here may be rounded up depending on the step size Calculate button Automatically calculates the number of rows and columns that can be plotted with the specified media size and spacing This button is disabled when Use Data specified Size is set for media size 15 5 3 Edit Media Size window Used to edit the list of media available for selection in Media size in the Output window Media Name Selects the medium for which length and width are to be modified The medium name can be edited but different media cannot share names Media Width 000000000 Specifies the medium width in 0 01 mm or 0 01 inch increments Media Length Specifies the medium length in 0 01 mm or 0 01 inch increments 16 DA Cut Simulation window The Cut Simulation wi
17. ndow simulates cutting at the preset interval It also allows modification of the sequence for single stroke groups Procedure 1 2 3 4 5 6 Press the H or gt button to start the output sequence simulation The H button runs the simulation for each single stroke group while the gt button runs the simulation for each object Group 1 6 shows the number of the group being displayed and the total number of groups To change the cutting sequence or to pause press the UI button This pauses the simulation leaving the group currently displayed as the selected group Press the gt gt button to move from group to group Press the WW button to move from group to group in reverse To resume the simulation from the selected group in the paused state press the or gt buttons You can adjust the simulation speed by changing Interval 1 0 See when the simulation is halted or paused The setting is only effective for intervals between 0 1 and 5 0 seconds To halt the simulation press the L button Press the E button to display all data adjusted to fit in the current window Press the gq button to display the data at twice the current size Press the CH button to display data at half the current size If a group or object is selected while the simulation is halted or paused the menu can be displayed by right clicking with the mouse Press the i button to select a group or press the AI button to select an o
18. ng object selection specifying an object in the window selects the single object saacifiad Object 1 4 SC Here shows the object in the group currently displayed and the total number of objects Use the Top menu or press the vi button to move the output sequence of the object selected to the top of the group Use the Bottom menu or press the ol button to move the output sequence of the object selected to the bottom of the group Use the Forward menu or press the E button to move the output sequence of the object selected one step forward in the group Use the Back menu or press the E button to move the output sequence of the object selected one step back in the group Use the Reverse menu or press the H button to reverse the output direction of the object currently selected Use the Divide menu or press the zg button to divide the output of the object currently selected Note that divided cutting is not possible when polyline objects are selected Use the Convert menu or press the al button when polyline objects are selected to convert polylines to line segments and arcs thereby allowing divided output Only polyline objects can be converted Note that objects cannot be returned to their original state once converted 18 Notes on divided cutting Over cutting may occur at the joins between line segments when cutting figures like that shown below in a single action Specifying divided cutting automatical
19. nlarge a part of the view window first specify the area to be enlarged by right clicking and dragging the mouse lt Changing the Sort method gt Select one of the four following sort methods from the Sort menu in the Output menu Settings such as the spacing for treating separated points as identical can be set in the Sort Settings window See 5 10 1 None Performs single stroke sorts by the conditions specified in the Cut Specification window 2 Layer Used to sort by layer Outputs in sequence from the layer displayed at the top of the Media Selection List when Layer is selected in Cut Method in the Cut Specification window 3 Color Used to sort by color Outputs in sequence from the color displayed at the top of the Media Selection List when Color is selected in Cut Method in the Cut Specification window 4 All Sorts all data to be output with the same output conditions regardless of the setting selected in Cut Method 10 5 Window details 5 1 Preferences window The Preferences window is used to enter settings applied to all data Step Size Selection Color Setting Specifies the unit size GDU for the position data sent to the plotter CAUTION This setting must match the plotter settings Change plotter settings when this setting is changed For more information on plotter operations see the plotter user s manual Specifies the unit used for displaying the coordinat
20. r Messages CAUTION Items marked lt lt gt gt contain error values or text 6 1 File related errors Insufficient working memory Not enough memory is available Close other open windows to free memory The file could not be found This message is displayed if the file to be opened could not be found Check the file name Incorrect file details An error occurred while loading a file Check that the file is a DXF file Invalid data The DXF file does not contain data that can be opened using D Cut Master File loading terminated The file loading was terminated by the ESC key Unable to read file An error occurred while attempting to load the file Check the file to be loaded This file type is not supported Attempted to load an unsupported file type Check the file extension Unable to create file Displayed if the destination path is incorrect or write protected Check the path name and write permission for the disk Unable to write file Displayed if the destination path is incorrect or write protected Check the path name and write permission for the disk Boge 6 2 Media size related errors Unable to find media The media name specified in the file saved could not be found Enter a new setting Media name lt lt Media name gt gt is reserved and cannot be used This is an invalid media name Rename the medium Unable to use lt lt character gt gt in media names The media name cont
21. r press the De button to return to the Output window ert 5 6 Cut Specification window Sets the cutting conditions Cut method Default Settings Edit Media List button Media Selection List 1 Layer Selects the method for specifying cutting for individual layers Color Selects the method for specifying cutting for individual colors Specifies the media used when Default Settings is selected in media selection This setting is also used for Cut Frame and page tiling Displays the Edit Media List window See 5 7 to permit editing of the media names listed for selection l Layer Color Displays the layer name or color The layer or color specified is not output if the checkbox at the head is deselected Ist to 5th Selects the output media from the drop down list Selecting Default setting uses the setting specified in the default settings 1st must always be specified Specify 2nd to 5th when multiple outputs are required f J buttons Output the top layers or colors first when sorting by layer or color Press these buttons to change the selected layer or color output sequence 21 5 7 Edit Media List window This window is used to edit the list of media available for selection in the Cut Specification window The list is saved to the Settings folder in the folder in which D Cut Master is installed Close button Exits m
22. rights are required in order to install this software Please log on to Windows as a member of the Administrators or Power Users group Full access rights to printer settings are required in order to install the software in Windows XP or to upgrade the driver Please log on to Windows as a user with Administrator rights When using Windows Vista Full access rights are required in order to install this software Please log on to Windows as a member of an administrative group If you are using a standard user account a User Account Control window appears and you will be required to enter the administrator account password 1 4 Precautions Only the following DXF objects can be imported line segments polygons splines circles arcs and ellipses Block referenced objects cannot be imported Text and dimension lines cannot be imported See the plotter user s manual for detailed information on setting up and operating the plotter If a polyline shape has been converted to segments and arcs at the Cut Simulation display it cannot be returned to its original shape When Using the FC3600 The FC3600 settings that have been pre registered in the Media List are all conditions for use with the pen carriage They cannot be used with the tool carriage This software cannot be used to adjust the height of the tool carriage Please make the height adjustment at the plotter control panel When using this software to specify
23. s sorting options Spacing Chain line If the ends of objects fall within the specified range they will be sorted into a single group Example Rectangle with dashed line segments If the spacing between the line segments outlining a rectangle falls within the range specified in Spacing in the Sort window the line segments will be connected and output as unbroken lines as shown below If the ends of objects fall within the specified range they will be sorted into a single group Unlike Spacing the spacing between the lines will be retained Example Rectangle with dashed line segments If the spacing between the line segments outlining a rectangle falls within the range specified in Chain line the segments making up the rectangle will be sorted into a single group However if the spacing between the line segments falls outside the range specified in Chain line the line segments will be sorted into separate groups and the Oe plotting sequence and direction will be sorted randomly e g sequence 1 2 3 o Group Priority Order 1 Feed Direction Sorts after creating single stroke groups in a sequence designed to minimize media feeding 2 Standard Creates single stroke groups in sequence from the top of the data contained in the DXF file 3 Distance Sorts after creating single stroke groups with the closest object groups placed first 962 6 Erro
24. the cutting force for the FC3600 please note that the values that can be set differ according to whether the setting is for a pen or a tool Refer to your plotter user s manual for the appropriate values before making the setting If you wish to specify the cutting force separately for the X and Y axes please make the settings at the plotter control panel At this time make sure that no cutting force or quality settings have been specified with the software 2 Setup 2 1 Installing the Graphtec Windows Plotter Driver D Cut Master uses a driver such as the Graphtec Plotter Driver OPS628 or Cutting Plotter Driver OPS662 as its output destination Before installing D Cut Master please install the Graphtec driver for the model that you plan to use 2 2 Installing D Cut Master Run the Setup exe on Disk 1 to launch the D Cut Master setup program Follow the instructions to install D Cut Master 2 3 Setting up the cutting plotter Set your cutting plotter s command protocol to GP GL Please refer to your cutting plotter user s manual for the setting procedure 3 Basic Operations When installed D Cut Master is added to the Start menu Click the D Cut Master icon in the Windows Start menu to launch the application D Cut Master SAMPLE DNF De Edit View Output Window Help OSE ek QQ d Z sotoider None DE E p 2 SAMPLE DXEF For Help press F1 lt Importing new data gt To import a new DXF file select
25. to use lt lt character gt gt in media names The media name contains an invalid character Rename the medium Specify a media name no greater than lt lt number of characters gt gt single byte characters in length The media name specified is too long Rename using a name no longer than the specified maximum length 30 The contents of this manual are subject to change without notice OPS639 D Cut Master User s Manual Issued June 20 2007 OPS639 UM 153 Issue 1 First printing 000 Published by GRAPHTEC CORPORATION 503 10 Shinano cho Totsuka ku Yokohama
Download Pdf Manuals
Related Search