UI CLY 370 MSC2544
Contents
1. KEMPSTON BEDFORDSHIRE UK t 444 0 1234 855855 Powering the Future a ala User manual for CLY 370 MSC 2544 Stripping tool for bonded screens on elastomeric cables and peelable semi concuctive layer A Stripping of bonded screens 1 Preparation of cable Clean the cable Put silicon grease on the bonded semi conductor 2 1 Preparation of tool Open the tool body by unscrewing nut 11 Pull the two parts of the body apart Loosen the screw by turning the bolt 8 by 180 do not unscrew completely Retract the blade 9 completely by turning screw 10 as far as it will go lf available use tool PLHMF for presetting the correct depth Preset the tool stop 7 by pushing the button 2 and select the remaining length of semiconductive layer according to the technical data sheet of the joint supplier The tool allows the following steps 30 40 45 mm see marking on the body picture The tools must be used on non live cables by skilled workers who are competent in cable preparation and know about electrical phenomenons Wearing gloves is obligatory Clean the tools after each use Powering the Future 2 2 Bonded semi conductor removal IMPORTANT Check that the removable insert is in position off Fit MSC 2544 onto bonded semi conductor as shown Tigthen screw 11 Set the blade 9 to the required depth by turning screw 10 if not pre set with PLHMF Tighten th2. insulation if the layer cannot be removed or marks remain on the insulation change the setting of the blade according to the description in 4 2 To stabilize the tool unlock screw 8 advance blade 9 by turning knob 10 so that it touches the semi conductive layer Lock screw 8 The removable insert can be taken out whilst the tool s body remains on the cable in its position The peeling is finished when the stop 13 comes in contact with the outer sheath Put knob 4 to off position and remove the tool The semi conductor has to be removed manually The tools must be used on non live cables by skilled workers who are competent in cable preparation and know about electrical phenomenons Wearing gloves is obligatory Clean the tools after each use
3. e bolt 8 If the black semi conductive layer is not completely removed reset blade according to description above E eth Rotate the tool BSC1 in the direction indicated by the arrow 7 until the body touches the sheath anana nnnnTT 3 Removal of the MSC 2544 Unlock bolt 8 Remove blade by turning screw 10 see picture above Loosen nut 11 Remove the MSC 2544 Spare blade part no BSC1ER Silicone tube 35 g Part no Silicone The tools must be used on non live cables by skilled workers who are competent in cable preparation and know about electrical phenomenons Wearing gloves is obligatory Clean the tools after each use Powering the Future B Stripping of peelable semi conductive layer 4 Preparation of cable D G 5 ALROC PELA Bip r ry Before starting preparation of the cable clean the cable straighten it out and check that its end is straight and clean The outer cable sheath must be removed 3 Use grease or silicone for better glidin g g g ON ma lig of the tool ll 4 1 Preparation of tool Press button 2 and completely insert the handle 3 as shown in the picture Turn the handle 3 until it locks Removable insert with blade for peelable semi conductive layers If it is not in place already put the complete insert in by pushing the button 6 Pull the knob 4 and turn to on position Select the correct cutting depths of the
4. removable x h t up and turn e ki FY Cutting insert as shown in the picture pull up the knob marked with the cutting depths and turn it until the ra de N olade desired cutting depths points to the blade release the knob so that it snaps audibly back into place You can choose 0 4mm 0 7 mm 0 9mm 1 1mm Put the removable insert with blade 4 into its position by pushing the button 6 as shown in the picture Turn the knob 4 to on position The tools must be used on non live cables by skilled workers who are competent in cable preparation and know about electrical phenomenons Wearing gloves is obligatory Clean the tools after each use ne Powering the Future Place the tool on the cable end and screw it in place g by turning the red nut 11 The position of the tool on the cable is shown in the picture to the right Preset the tool stop 7 by pushing the button 2 and select the remaining length of semi conductive layer according to the technical data sheet of the joint supplier The tool allows the following steps 30 40 45 mm see marking on the body picture Turn knob 4 to on position Peel off the screen by rotating the tool in the direction 4 indicated on the tool 12 and by the green arrow in ON 10 the picture Make four complete turns A ey euro PELABLE d P Check that you can peel off the semi conductive layer and no marking remains on the
Download Pdf Manuals
Related Search