AcPC4610 User`s Manual
Contents
1. Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier 3 The ACPC4610E CC is a 3U CompactPCI Bus Non Intelligent PMC 1 0 GENERAL carrier board designed for the 32 bit 33MHz or 66MHz CompactPCI bus The carrier card uses a PLX Technology Bridge Chip PCI6540 to interface INFORMATION between the CompactPCI bus and one PMC mezzanine I O module card Model ACPC4610E is an air cooled extended temperature product which MODEL ACPC4610E can be used for front and rear PMC mezzanine I O modules Front I O can be accessed through the front panel Rear I O can be accessed though the J2 connector on the carrier e ESD Strip on ACPC4610E Board The ACPC4610E board has been KEY FEATURES designed to provide electrostatic discharge ESD capability by using an ESD strip on the board per IEEE1101 10 e Injector Ejector Handle The ACPC4610E uses a modern injector ejector handle which pushes the board into the rack during installation and has a positive self locking mechanism so it cannot be unlocked accidentally This handle is fully IEEE 1101 10 compliant and is needed to give leverage to install and remove the board e EMC Front Panel The ACPC4610E uses the preferred EMC front panel per IEEE 1101 10 specification Model ACPC4610CC is a conduction cooled product which is usually MODEL ACPC4610CC only used for rear Conduction Cooled PMC mezzanine I O modu2. 4 0 0 0 INCHES P1 TOP VIEW G Xy PIN 34 PIN 68 PISA o o Y Y PIN 68 gooo0o0000000000000000000000000000 gt 00000000000 0000000 00000000000000d 00000000000 0000000 000000000000000 D00000000000000000000000000000000 PIN 1 PIN 35 PIN 1 Y PIN 35 A o N ES FRONT VIEW MODEL 5028 432 SCSI 3 68 PIN CABLE ASSEMBLY SHIELDED 4501 919C lENUEN SA8SN DO A0L9VOdDV L JAILED OWd sng 1942edu09 woo BewoJl9emww dyy Woo HewoJoe suoljnjos iewy yez6 129 8pZ Xe4 OL O S62 8pz I8L oul Beuloloy e 123 45 67 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 TB1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 4950 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 MODEL 5025 288 TERMINATION PANEL SCHEMATIC 182 PINS 1 amp 2 ARE TIED TO J1 METAL HOUSING en
3. 85 C Relative Humidity 5 95 Non Condensing Storage Temperature 55 C to 100 C Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier Q Also designed to meet the following environmental standards per ANSI VITA47 2005 R2007 Model ACPC4610E amp TRANS C4610 e Environmental Class EAC6 e Operating Temperature AC3 40 to 70 C e Vibration Class V2 o Shock 20g Model ACPC4610CC e Environmental Class ECC4 e Operating Temperature CC4 40 to 85 C e Vibration Class V3 o Shock 40g 3 3 VDC 5 Typical 135 mA Max 150 mA 5 0 VDC 5 Typical 50 mA Max 70 mA 3 3 VDC 5 Per PMC Module Maximum 5 0 VDC 5 Per PMC Module Maximum 12 VDC 45 Per PMC Module Maximum 12 VDC 45 Per PMC Module Maximum With no PMC module installed 12 VDC and 12VDC not used Maximum power of 7 5 Watts Total of all supplies per PMC standard Maximum Power for Rear Transition Modules 3 3 VDC Maximum 3 Amps Fused at 4 Amps 5 5 VDC Maximum 2 Amps Fused at 3 Amps Note Model TRANS C4610 does not use 3 3 VDC or 5 0 VDC power This device meets or exceeds all written PCI Specification Version 2 3 amp CompactPCl Specification PICMG 2 3 R1 0 Non Isolated PCI bus and field commons have a direct electrical connection PMC Compatibility Pin assignment conform to PCI Bus Specification Revision
4. Memory Does this product contain Volatile memory i e Memory of whose contents are lost when power is removed Yes m No Type SRAM SDRAM etc Size User Function Process to Sanitize Modifiable Yes No Type SRAM SDRAM etc Size User Function Process to Sanitize Modifiable Yes No Type SRAM SDRAM etc Size User Function Process to Sanitize Modifiable Yes No Non Volatile Memory Does this product contain Non Volatile memory i e Memory of whose contents is retained when power is removed Yes m No Type EEPROM Flash etc Size User Function Process to Sanitize Modifiable Yes No Type EEPROM Flash etc Size User Function Process to Sanitize Modifiable Yes No Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com
5. assumes no responsibility for CompactPCI Bus Connector 6 any errors that may appear in this manual and makes no commitment to update or 3 0 SERVICE AND REPAIR keep current the information contained in this manual No SERVICE AND REPAIR ASSISTANCE RS TT PS PR TE aa 7 part of this manual may be PRELIMINARY SERVICE PROCEDURE nus memes 7 copied or reproduced in any WHERE TO GET HELP a E fe 7 form without the prior written consent of Acromag Inc 4 0 SPECIFICATIONS PHYSICAL cidad incida 8 CONNECTORG 0ccccescecseecesenseeeeeeeeseeeeneeees 8 ENVIRONMENT AL 8 POWER REQUIREMENTS 9 CompactPCI BUS COMPLIANCE 9 RELIABILITY PREDICTION ccccceccecececsssssseses 9 APPENDIX MODEL TRANS C4610 10 MODEL 5028 432 ccccccceceeeeeseeeeeeeeeeeeeeeeeeees 10 MODEL 5025 288 c ccccececeeeeeeeeeeeeeeeeeeeeeeees 11 DRAWINGS MODEL ACPC4610E 12 MODEL ACPC4610CC inner 13 4502 096 ACPC4610 BLOCK DIAGRAM 14 MODEL TRANS C4610 15 4502 089 TRANS C4610 SCHEMATIC 16 4501 919 MODEL 5028 432 17 4501 920 MODEL 5025 288 18 Certificate of Volatility 19 Trademarks are the property of their respective owners
6. male connector with back shell Keying The SCSI 3 connector has a D Shell Schematic and Physical Attributes See Drawing 4501 919 Electrical Specifications 30 VAC per UL and CSA SCSI 3 connector spec s 1 Amp maximum at 50 energized SCSI 3 connector spec s Operating Temperature 30 C to 80 C Storage Temperature 40 C to 85 C Shipping Weight 1 0 pound 0 5Kg packed Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier 1 1 Type Termination Panel For CompactPCl Boards MODEL 5025 288 Application To connect field I O signals to the CompactPCI Board Termination Panel Acromag Part 4001 066 The 5025 288 termination panel facilitates the connection of up to 68 field I O signals and connects to the CompactPCI Board connectors only via a round shielded cable Model 5028 432 Field signals are accessed via screw terminal strips The terminal strip markings on the termination panel 1 68 correspond to field I O pins 1 68 on the CompactPCI board Each CompactPCI board has its own unique pin assignments Refer to the CompactPCI board manual for correct wiring connections to the termination panel Schematic and Physical Attributes See Drawing 4501 920 Field Wiring 68 position terminal blocks with screw clamps Wire range 12 to 26 AWG Mounting Termination panel is snapped on the DIN mounting rail Pri
7. 10E CC User s Manual CompactPCI Bus PMC Carrier faa O oO Q N o LO lt 5388583885883 888888583835833828358838 eee es Z g g a S a a 52 a a a a a 81 Sy SS US 41 3 5 5 Ss oS a oO oS 4 a S g pg g x kr O a o O x O O wz O LL O 2 I E N 3 t Z a P Yn E Q ul LE o DE 23 SS 228 aS Sl a a a Al a Ss Sl e Ss e 9 3 e el S al al el ol el el al 23 SEESEREESESERESSSESSSESSSESSSEERESEESE lt a Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com wo BewoJoemwm dyy woo Bewosse suonnos lIeuz pez6 p29 8bZ X24 OL O 96Z 8pz Je1 ou Beuwoloy P2 GROUND SHIELD ON CABLE CONNECTS TO P1 amp P2 SHIELDED BACKSHELL P1 ey Sana ANN NNONNNWOWWOHOWOWARAARL aan FNORUOVROSINGRTASISS SPNSRHSNSSSERS RFS SSSSESRESSSESSIIILAGASSSLISLASAS YY SCHEMATIC D amp BU D OO lt 2 METERS gt P2 78 72 INCHES
8. 2 3 and PMC Specification P1386 1 Signaling 3 3V signaling as required by the PMC module 5V signaling PMC modules may tolerate 3 3V signaling PCI Bus Clock This product is not guaranteed to function with a CompactPCl bus clock frequency greater than 66MHz PLX Technology Bridge Chip PCI6540 For more information on this bridge chip go to www plxtech com Mean Time Between Failure 2 558 049 hours ACPC4610E CC 25 C Using MIL HDBK 217F Notice 2 POWER REQUIREMENTS CompactPCI Bus Compliance Reliability Prediction Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com 1 0 ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier APPENDIX MODEL TRANS C4610 Type Transition module for ACPC4610 boards l Application To repeat field I O signals of PMC modules for rear exit from CompactPCl card cages This module is available for use in card cages which provide rear exit for I O connections via 80 mm wide transition modules transition modules can only be used in card cages specifically designed for them It is a single height 3U single slot module and adheres to the CompactPCI mechanical dimensions and IEEE Standard 1101 11 1998 with a printed circuit board depth of 80mm which is a standard transition module depth The transition module connects to Acromag Termination Panel Model 5025 288 using a round 68 conductor shielded cable Model 5028 432 to the rear of the
9. AcromagkY ACPC4610E CC CompactPCI Bus Non Intelligent PMC Carrier Board USER S MANUAL ACROMAG INCORPORATED Tel 248 295 0310 30765 South Wixom Road Fax 248 624 9234 P O BOX 437 Wixom MI 48393 7037 U S A Solutions acromag com Copyright 2008 Acromag Inc Printed in the USA Data and specifications are subject to change without notice 8500 819 C09J010 2 ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier TABLE OF IMPORTANT SAFETY CONSIDERATIONS CONTENTS You must consider the possible negative effects of power wiring component sensor Or software failure in the design of any type of control or monitoring system This is very important where property loss or human life is involved It is important that you perform satisfactory overall system design and it is agreed between you and Acromag that this is your responsibility 1 0 General Information The information of this manual KEY FEATURES ici ida 3 may change without notice SIGNAL INTERFACE PRODUCTS 3 Acromag makes no warranty of any kind with regard to this 2 0 PREPARATION FOR USE material including but not UCD to MEME Le UNPACKING AND INSPECTlON cococcococociococonconos 4 warranties of merchantability CARD CAGE CONSIDERATIONS e se eseeeeeee 4 and fitness for a particular Non lsolation Considerations lt s s 4 purpose Further Ach omag Rear 1 0 Connector 5
10. REPAIR ASSISTANCE PRELIMINARY SERVICE PROCEDURE CAUTION POWER MUST BE TURNED OFF BEFORE REMOVING OR INSERTING BOARDS WHERE TO GET HELP www acromag com Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com 3 ACPC4610E CC User s Manual 4 0 SPECIFICATIONS PHYSICAL Physical Configuration Height Depth Board Thickness Unit Weight Model ACPC4610E Model ACPC4610CC Connectors J1 CompactPCI Bus CompactPCI Bus PMC Carrier 3U CompactPCI 5V 3 3V Board 3 937 inches 100 0 mm 6 299 inches 160 0 mm 0 063 inches 1 60 mm 0 35 pounds 0 16 Kg 0 50 pounds 0 23 Kg PCI Specification Version 2 3 amp CompactPCI Specification PICMG 2 0 R3 0 Connector interfaces to the PLX Technology Bridge Chip PCI6540 primary side Type A right angle female connector 110 contacts with upper shield Note This board is universal 3 3V or 5V signal tolerant J2 CompactPCI Rear I O J11 12 J14 PMC on CompactPCl Specification PICMG 2 3 R1 0 Utilizes Type B right angle female connector 110 contacts with upper shield Not compatible with 64 bit CompactPCI or PXI PMC bus connectors Molex 71439 0164 or equivalent interfaces to the PLX Technology Bridge Chip PCI6540 secondary side PMC Rear I O connector Molex 71439 0164 or equivalent interfaces J2 ENVIRONMENTAL Models ACPC4610E ACPC4610CC and TRANS C4610 Operating Temperature 40 to
11. card cage and to ACPC4610 board within the card cage Schematic and Physical Attributes See page 15 and 16 Field Wiring 68 pin SCSI 2 connector P1 Connections to ACPC4610 Connections are made though the PC board connector J2 110 signals female right angle with upper ground shield The transition module plugs directly behind the ACPC4610 board into the 3U CompactPCI bus backplane within the card cage system Mounting Transition module is inserted into a 3U size 80 mm width slot at the rear of the CompactPCI bus card cage Directly behind ACPC4610 board Printed Circuit Board Four layer military grade FR 4 epoxy glass circuit board 0 063 inches thick Operating Temperature 40 C to 85 C Storage Temperature 55 C to 100 C Shipping Weight 0 25 pounds 0 11Kg packed MODEL 5028 432 Type Round shielded cable 68 wires SCSI 3 male connector at both ends The cable length is 2 meters 6 56 feet This shielded cable is recommended for all I O applications both digital 1 0 and precision analog I O Application Used to connect Model 5025 288 termination panel to the ACPC4610 Board Length Standard length is 2 meters 6 56 feet Consult factory for other lengths It is recommended that this length be kept to a minimum to reduce noise and power loss Cable 68 conductors 28 AWG on 0 050 inch centers permits mass termination for IDC connectors foil braided shield inside a PVC jacket Connectors SCSI 3 68 pin
12. e 9 Ne 20 Ne 21 Ne 22 Ne Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com 6 ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier CompactPCI Bus Table 2 2 indicates the pin assignments for the 32 bit CompactPCI bus Connectors for J1 signals at the J1 connector The connector consists of 25 rows of six pins labeled A B C D E and F Pin A1 is located at the lower right hand corner of the connector if the board is viewed from the front component side Refer to the CompactPCI bus specification for additional information on the CompactPCI bus signals RowA RowB RowC RowD RowE RowF V Table 2 2 CompactPCI Bus J1 Connections 5V 1 0 Y KEY AREA 5 REQ64 otes 1 Pound is used to indicate an active low signal 2 BOLD ITALIC Logic Lines are NOT USED by this carrier board Pin 6 EA ES EA Not Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com ACPC4610E CC User s Manual Surface Mounted Technology SMT boards are generally difficult to repair It is highly recommended that a non functioning board be returned to Acromag for repair The board can be easily damaged unless special SMT repair and service tools are used Further Acromag has automated test equipment that thoroughly checks the performance of each board When a board is first produced and when any repair is made it
13. instructions It is suggested that salvageable shipping cartons and packing material be saved for future use in the event the product must be shipped This board is physically protected with packing material and electrically protected with an anti static bag during shipment However it is recommended that the board be visually inspected for evidence of mishandling prior to applying power Refer to the specifications for loading and power requirements Be sure that the system power supplies are able to accommodate the power requirements of the system boards plus the installed Acromag board within the voltage tolerances specified In an air cooled assembly adequate air circulation must be provided to prevent a temperature rise above the maximum operating temperature and to prolong the life of the electronics If the installation is in an industrial environment and the board is exposed to environmental air careful consideration should be given to air filtering In a conduction cooled assembly adequate thermo conduction must be provided to prevent a temperature rise above the maximum operating temperature The board is non isolated since there is electrical continuity between the CompactPCI bus and PMC module grounds As such the field I O connections are not isolated from the system Care should be taken in designing installations without isolation to avoid noise pickup and ground loops caused by multiple ground connections Acromag I
14. is tested placed ina burn in room at elevated temperature and retested before shipment Please refer to Acromag s Service Policy Bulletin or contact Acromag for complete details on how to obtain parts and repair Before beginning repair be sure that all of the procedures in Section 2 Preparation For Use have been followed Also refer to the documentation of your PMC module to verify that it is correctly configured Replacement of the board with one that is known to work correctly is a good technique to isolate a faulty board If you continue to have problems your next step should be to visit the Acromag worldwide web site at http www acromag com Our web site contains the most up to date product and software information Choose the Support hyperlink in our website s top navigation row then select Embedded Board Products Support or go to http www acromag com subb_support cfm to access e Application Notes Frequently Asked Questions FAQ s Knowledge Base Tutorials Software Updates Drivers An email question can be submitted from within the Knowledge Base or through the Contact Us hyperlink at the top of any web page Acromag s application engineers can also be contacted directly for technical assistance via telephone or FAX through the numbers listed at the bottom of this page When needed complete repair services are also available CompactPCI Bus PMC Carrier Y 3 0 SERVICE AND REPAIR SERVICE AND
15. les Rear I O can be accessed though the J2 connector on the carrier e Conduction Cooled Frame The ACPC4610CC board has a custom KEY FEATURES conduction cooled assembly consisting of a conduction cooled frame thermo bars ejector injectors and Wedge Loks designed to thermally conduct heat away from the Conduction Cooled PMC modules per ANSI VITA 30 1 2001 Model TRANS C4610 Transition Module This module plugs into the SIGNAL INTERFACE rear backplane directly behind the ACPC4610E carrier board The field I O PRODUCTS connections are made through the backplane to the J2 connector of the carrier board and then routed to a 68 pin SCSI 3 connector P1 on the ee Trans sn transition module for rear exit from the card cage This module is available for use in card cages which provide rear exit for I O connections via 80 mm wide transition modules transition modules can only be used in card cages specifically designed for them It is a single height 3U single slot module and adheres to the CompactPCI mechanical dimensions and IEEE Standard 1101 11 1998 with a printed circuit board depth of 80mm which is a standard transition module depth The transition module connects to Acromag Termination Panel Model 5025 288 using a round 68 conductor shielded cable Model 5028 432 to the rear of the card cage and to the ACPC4610E board within the card cage Model 5028 432 A 2 meter cable with a male SCSI 3 connector at both Cables ends and 34
16. nc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier 5 The model ACPC4610E CC carrier field I O connections are made through Rear 1 0 Connector the rear via J2 for a single PMC mezzanine I O module card Table 2 1 indicates the pin assignments for the CompactPCI I O signal mapping at the J2 connector The connector consists of 22 rows of six pins labeled A B C D E and F Pin A1 is located near the center of the board viewed from the front component side J2 is used to route a single PMC Module s field signals from the carrier to the backplane IMPORTANT Model ACPC4610E CC cannot be used in 64 bit cPCI or PXI systems as rear I O J2 is mapped to the same connector as the additional control lines for 64 bit cPCI or PXI Table 2 1 CompactPCI I O ow Fons RowC RowD Rowe Row Signals J2 nece HU 54 58 53 a a 38 33 28 18 MEN MER 3 3 3V FE Ne 7 TEE O Ne O Ne 1 NC O Ne Ne Ne oO A al oO N al T 3 3V 3 3V sv Notes 1 Entries in the table are of the PMC J14 pin number 2 NC is no connections NOT USED by this carrier board 3 VI O NOT USED by this carrier board asg C Pin Row A 1 wo 2 60 3 5 4 50 el a ee La 4 7 3 8 30 a oe to 20 En Er p13 5 14 3 3V_ 15 NC EC Ne EA Ne _18 N
17. nted Circuit Board Military grade FR 4 epoxy glass circuit board 0 063 inches thick Operating Temperature 40 C to 100 C Storage Temperature 40 C to 100 C Shipping Weight 1 0 pounds 0 5kg packaged Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com 1 2 ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier Model ACPC4610E J2 J1 aaa Toalla e SCOOT dll MA AALLAR HRL 4 o Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier 1 3 Model ACPC4610CC J2 J1 Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com wo BewoJoemwm dyy woo Bewosse suonnos leuz pez6 p29 8bZ X24 OL O 96Z 8pz Je1 oul BeuoJoy Compact PCI BUS REAR FIELD 1 0 PMC SLOT 1 FOR J1 PLX TECHNOLOGY PCI6540 INTERFACE BRIDGE CHIP PMC CONNECTORS J2 J12 J11 ee F1 3 AMP FUSE 5 VDC J14 F2 PMC SLOT 1 4 AMP FUSE lt 3 3 VDC ACPC4610 BLOCK DIAGRAM 4502 096B lENUEN S18SN 99 101979d49V y L Jaep DIN Sng 1D peduloo ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier 1 5 Model TRANS C4610 TP1 Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com ACPC46
18. twisted pairs This cable is used for connecting the TRANS C4610 board to Model 5025 288 termination panels Model 5025 288 DIN rail mountable panel provides 68 screw terminals Termination Panel for universal field I O termination Connects to the TRANS C4610 board via SCSI 3 to twisted pair cable Model 5028 432 Acromag Inc Tel 248 295 0310 Fax 248 624 9234 Email solutions acromag com http www acromag com 4 2 0 PREPARATION FOR USE UNPACKING AND INSPECTION Y sea AUTIO DEVICES 0 NOT SHIP OR STORE NEAR STRONG EECTR STAT ELECTROMAGNETI AGNETR OR RADIOACTIVE HELDE WARNING This board utilizes static sensitive components and should only be handled at a static safe workstation CARD CAGE CONSIDERATIONS IMPORTANT Adequate air circulation must be provided to prevent a temperature rise above the maximum operating temperature Non Isolation Considerations ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier Upon receipt of this product inspect the shipping carton for evidence of mishandling during transit If the shipping carton is badly damaged or water stained request that the carrier s agent be present when the carton is opened If the carrier s agent is absent when the carton is opened and the contents of the carton are damaged keep the carton and packing material for the agent s inspection For repairs to a product damaged in shipment refer to the Acromag Service Policy to obtain return
19. ue S188N 99 101970d9V 9 L PIN 68 TB2 DO J1 Jo uu o 3 alr 12 8 H PIN 1 s L T TB2 12 3 40 Ul AD 86 36 H PLACE MODEL SERIAL gt ZA LABEL HERE TB1 cl 2OQOOOOOOOOOOOQOODDOOOOOOCDOOOOOOQOOS b E H DODOOODOOOOODDODODOOOOODODOODDOODOOORQ Y Ii SIDE VIEW lt 180 34 TOP VIEW A NOTE O 1234 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 DIMENSIONS ARE IN INCHES o E i MILLIMETERS 3 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 TERMINATION T 27 TH H H H H HH MARKINGS O 68 58 2 Q WwW C y Nm 0 FRONT VIEW 4501 920B O O D 3 9 ACPC4610E CC User s Manual CompactPCI Bus PMC Carrier 1 Q Certificate of Volatility Acromag Model Manufacturer ACPC4610E Acromag Inc ACPC4610CC 30765 Wixom Rd TRANS C4610 Wixom MI 48393 Volatile
Download Pdf Manuals
Related Search