ME61 Single Strand Fiber Converter
Contents
1. Note You must set DIP Switch 1 to FORCE when DIP Switches 2 and 3 are set to 10 and HDX respectively For ME61 DIP Switch 5 must be set to FDX After resetting the DIP Switches you must reboot ME61 to activate the new settings 7 Link Fault Pass through This media converter supports Link Fault Pass through LFP for TX FX converter applications Link status on one port is propagated to the other port to notify remote nodes If the TP port is unplugged the ME61 stops transmitting over the fiber port causing the remote fiber node link to fail The LED will show link failure on both the TP and fiber ports If the fiber link fails the ME61 restarts auto negotiation on the TP port Normal status via a pair of LFPs Remote Station 10 100 10 100 Status if TP Ais broken 10 100 10 100 Switch A Switch Station B ome ML et ene able Remote O o O o Status if Fiber Cable B is broken 10 100 10 100 Remote Station Note indicates LNK ACT LED Lit O indicates LNK ACT LED Off Warning The LFP Link Fault Pass Through function works only when two converters working in pairs have this capability Furthermore both LFP converters should be supplied by the same manufacturer vender The connection comes from LFP converters with odd models or non LFP converters will cease the LFP function 8 LED Description but stays in the link failure state This causes the rem2. show pinouts for both MDI NIC type ports and MDI X HUB Switch type ports as well as cable wiring diagrams for straight through and cross over Ethernet cables RJ45 8 pin to RJ45 8 pin Straight Through Cable Wiring Straight Through Cable Switch Port F i NIC Port RJ45 Plug Pin 1 i RJ45 gt RJ45 Connector Cable Wiring Connector Tx 3 3 Ret Tx 6 6 i Rx Rx 1 1 Tx Rx 2 2 1 D RJ45 8 pin to RJ45 8 pin Cross Over Cable Wiring Switch Port Cross Over Cable Switch Port NIC Port T TE NIC Port RJ45 Plug Pin 1 RJ45 gt RJ45 Connector Cable Wiring Connector Rx Tx i 3 1 i Rx Tx Rx Tx i 6 2 gt Rx Tx Tx Rxt 1 3 Txt Rx Tx Rx 2 6 Tx Rx 6 DIP Switch Settings Power input settings e Power source from AC DC e Power over USB enabled Power Adapter enabled 5VDC USB 5VDC USB DIP Switch DIP Switch 3 Communication settings AUTO 100 FDX LFP FDX TAE T 2 3 FORCE 10 HDX LFP HDX L DIS TP FX DIP Switch DIP Function FX FDX FX at full duplex default HDX FX at half duplex LFP Enable Link Fault Pass through default LFP DIS Disable Link Fault Pass through FDX TP at full duplex default HDX TP at half duplex when TP at Force 100 TP at 100M default 10 TP at 10M when TP at Force AUTO TP at auto negotiation default FORCE Force TP at 10M or at half duplex TP
3. MOXA ME61 Single Strand Fiber Converter Second Edition June 2008 1 Overview Moxa ME61 Single Strand Fiber Converter is a standalone physical layer device that converts between 10 100BaseT X and 100BaseFX segments of the same network e Rear Panel View This device complies with Part 15 0f the FCC Rules CE MADE IN TAIWAN 5VDC USB OCO 4 Wiring the Power Inputs Using ME61 with the AC DC Power Adapter ME61 is designed with an optic Wavelength Division Multiplexing WDM 1 Use DIP switch settings to enable power through the AC DC Power technology that transports bi directional and full duplex signals over a single strand fiber cable simultaneously ME61 is powered by an external power adapter or by the USB port of the host e g PC or NB 2 Package Checklist Moxa ME61 products are shipped with the following items e 1 ME61Aor 1 ME61B e AC DC Power Adapter e ME61 User s Manual Please notify your sales representative immediately if any of the above items is missing or damaged 3 Model Descriptions Model TX RX Wavelength TX Transmit 1310 nm MEST RX Receive 1550 nm TX Transmit 1550 nm MESIs RX Receive 1310 nm Panel Layout of ME61 series e Front Panel View FX TP O ines w COL Orwe Bridge Media Converter 10 100Base TX to 100Base FX e Side Panel View olny Xad oL n
4. e 0 to 50 C Humidity 5 to 90 Dimensions 26 2 H x 70 3 W x 94 D mm Complies with FCC Part 15 Class A and CE Mark Click here for online support MOXA Wwww moxa com support The Americas 1 714 528 6777 toll free 1 888 669 2872 Europe 49 89 3 70 03 99 0 Asia Pacific 886 2 8919 1230 China 86 21 5258 9955 toll free 800 820 5036 2008 Moxa Inc all rights reserved Reproduction without permission is prohibited P N 1802000610112 6
5. e 001 XGH ko X04 sidds1 aan XAH ln 1 3 D O m X4 XAH fi Adapter refer to Part 6 for DIP switch settings 2 Verify that the AC DC adapter conforms to your country s AC power requirements and then insert the power plug 3 Connect ME61 to the network Note Wear a grounding device to safeguard against injury due to electrostatic discharge Using ME61 with Power over USB 1 Use DIP switch settings to enable power from the USB port refer to Part 6 for DIP switch settings Note Please ensure that the DIP switch is positioned on the USB side of the slider 2 Install the USB cable Plug the type A connector in the PC s USB port and the type B connector in the ME61 s USB port see Fig 1 3 Connect ME61 to the network Warning Make sure that the PC s power is turned on Otherwise the ME61 will not receive power 4 USB Type A Jack A Yo A USB Cable USB Type B Jack J 100FX Fiber Fiber Optic Network ee RJ 45 Jack 10 100 Ethernet Cat 5 Cable Switch NIC Fig 1 ME61 with USB power source Type B to Type A Plug and FX TP connection ME61A ME61B UDM single Ei TX 1550 RX 1310 WRU Single bibs X 1310 RX 1550 Single Strand Fiber Fig 2 Basic Network Connection 5 Communication Connection ME61 models have one 10 100BaseT X Ethernet port and one 100 BaseFX SC fiber port 10 100BaseT X Ethernet Port Connection ME61 supports auto MDI MDI X Below we
6. ote TP node link to fail The LED also shows the link failure on both the TP and fiber ports The figures below show normal status when the link succeeds and the error status when TP Cable A Fiber Cable B or Fiber Cable C fails to connect Note The Link Fault Pass through LFP function is enabled by DIP switch Disable the LFP function by setting the DIP switch to the LFP DIS position FX LNK Green Lit when FX port is linking ACT Blinks when FX port is transmitting data FX FDX Lit when full duplex mode is active ICOL Amber Off when half duplex is active Blinks when a collision occurs TP LNK Green Lit when TP port is linking ACT Blinks when FX port is transmitting data Lit when TP port is transmitting data at 100 Mbps TP 100 Green Off when TP port is transmitting data at 10 Mbps PWR Green Lit when 5V power is supplied 5 eo Technical Specifications Standards IEEE802 3u 10 100Base TX 100Base FX Flow Control IEEE802 3x compliant for full duplex Back pressure flow control for half duplex TP Cable Limitations Cat 5 and up to 100m Fiber Optic Cable Single Strand Fiber Cable Recommended 9 125 uum single mode Optional 8 3 125 8 7 125 or 10 125 wm Wavelength ME61A TX 1310 nm RX 1550 nm ME61B TX 1550 nm RX 1310 nm Min TX Output 10 dBm Max TX Output 7 dBm Sensitivity 32 dBm Power Requirement 1A 5VDC from AC DC Adapter 0 5A 5VDC from USB port Ambient Temperatur
Download Pdf Manuals
Related Search