GARDTEC 480
Contents
1. 7 The system will now start the relevant Set with the zones you deleted removed from the Set Note This will be for the one Set state only System Test This option allows the User to test zones bells and strobes on the system 1 Enter a valid Master User Code followed by No X The display will show Do You Want to Test 2 Press Yes The display will show Walktesting O k 3 Walk around the area being tested As each device is operated there will a tone from the internal sounders and the display will show the triggered circuit 4 To test the bells external sounders and strobe press 9 To stop the bell test press 9 again 5 To escape back to Unset press 0 three times Turning Chime On Off Your installation company may have programmed the system so that a chime tone sounds when certain doors are opened or a detector is triggered This Chime function may be turned on or off by the User 1 Enter a valid Master User Code followed by No X cd The display will show 2 Press No X Do You Want to Delete Zone The display will show 3 Press No X Do You Want to The display will show Select Options 4 Press Yes The display will show Do You Want to Program Chime Press Yes t again 5 The current Chime Mode will be displayed Use the No X key to change it to2. Unsetting the System via a Keyswitch if fitted Biased Keyswitch To set the system with a biased keyswitch insert the key and turn it then return the key to the original position and remove Follow the instructions from step 3 above To unset repeat this operation Pre Exit Check At the start of the setting procedure a fault i Exit Now I tone will sound if any non exit routes are Zone 3 open The display will show for example If the fault clears within 20 seconds then the exit tone will begin if not the fault tone will continue until a valid User code is entered Part Setting the System using Part 1 Up to three Part Sets may be available for your system Please refer to the customer details at the rear of this manual for information about Part Set zones Part Set zones will be omitted from the system when that particular Part Set is used To set the system using Part 1 1 Enter a valid User Code followed by 1 E 2 Retire to an unprotected area Note To abort the exit enter a valid User Code Part Setting the System using Part 2 or 3 Two other Part Sets may be available for your system Part 2 is a second set of zones that may be omitted and Part 3 will combine Part 1 and Part 2 To use Part 2 or 3 Note Enter a valid User Code followed by 2 or 3 Retire to an unprotected area To abort the exit enter a valid User Code The exit tone may or ma
3. the mode you require When finished press 0 three times to return to the Unset mode Page 17 Setting Time amp Date 1 Enter a valid Master User Code followed by No X The display will show Press No X The display will show Press No X The display will show Press Yes The display will show Press No X The display will show Press No X The display will show Press Yes The display will show Do You Want to Test Do You Want to Delete Zone Do You Want to Select Options Do You Want to Program Chime Do You Want to Program Codes Do You Want to Set Date Time Type Day Mnth 0000 Enter the Day and Month e g 0307 for 3rd July followed by Yes The display will show Type Hrs Mins 0000 Page 18 9 Enter the time using the 24 Hour clock e g 2300 for 11pm followed by Yes 1 The display will show for example 10 Press Yes to accept The display will show 11 To return to the Unset Mode press 0 twice 03 Jul 23 00 Ok Do You Want to Set Date Time It should be noted that the time displayed after setting the time may be plus or minus one minute Reading the Log 1 Enter a valid Master User C
4. RISCO Creating Security Solutions 9 y Wee Care GT480 Contro Panel User Instructions Contents Introduction vapores Tre S 1 Display Status Blanking LL 2 IMPORTANT USER INFORMATION 2 Full Setting the System 3 Setting amp Unsetting the System via a Keyswitch 3 Pre Exit Check 2 04 02 ae SIL 4 Part Setting the System using Part 1 4 Part Setting the System using Part 2 or3 5 Unsetting the System LL 6 Display After Alarm Lei 6 Resetting After Alarm 7 Tamper Reset insite tire ars ori 9 Setting the System with Mains Fail 10 Programming User Codes 12 Programmable User Options 15 Zone Remove Option 15 System Test iii 16 Turning Chime On Off LL 17 SettingiTime amp Date asc c cages calas 18 Reading theilog soii iia Pe Pelia 20 Keypad Alert a ere a altera 21 Keypad Tamper iii es 21 Jamper iii RR AAA 21 System Details 22 Introduction Welcome to the GT480 control panel Your installation company will have programmed your system to protect your premises to the highest possible standards Several user programmable options are available that will be covered later in this manual Throughout this manual reference will be made to the Master User Code The factory set default is 5678 This code is programmable along with eight other User Codes If an Engineer is on site it may be necessary to authorise them to acc
5. engineer will give a return Anti Code this may contain the YES lt lt amp NO X keys for example 5 YES lt lt 2 4 2 Enter this Anti Code into the keypad The system is now reset Tamper Reset If a fault or tamper occurs when the system is in Day Unset mode the fault sounder will operate The display will show 1 CHECK 1 To view the cause of the fault enter your User Code The display will show for example III CHECK i Tamper 2 The message will stay on the display for 10 seconds or until you a ee Ths display 1 CHECK After the cause of the fault has been recti fied the system will need to be reset The terms of your insurance may prohibit User reset If Tamper Reset has been programmed for Engineer Reset the display will show SERVICE DUE for 10 seconds each time the user attempts to set the system Please contact your installation company Tamper Resetting Enter a valid User code Then press Yes 4 2 The exit tone will sound and Exit Now the display will show Ok 3 Enter your User code again to abort the setting 1 With the display showing 111 CHECK 11111 The system is now reset Setting the system with Mains Fail In the event of a short term power cut where it is known when power will be restored e g Engineers worki
6. ess your system Do this by entering your User Code when asked to do so by the engineer One of two types of Keypad may be fitted to your system the first type has Text on the keys for example Yes and No Keys The second type uses Icons and is designed to be multi lingual see table below Icon style keypad Text style keypad III IMPORTANT The Keypad may have Icon style keys instead of Text style keys Please use the table above for a conversion of the different styles This will be reflected in this manual for example Display Status Blanking Depending on Control Panel installed it may be a requirement that the Status Set or Unset display of the security system is not displayed Set or Unset Status will only be displayed for ten seconds when the system is Set or Unset The bottom line of the display will then be blanked off IMPORTANT USER INFORMATION If the Control Panel is non EN then all displays will be shown and CHECK will not be displayed All information displays will remain until cleared by the User Full Setting the System After checking the premises are secure 1 Enter a valid User Code followed by Yes 2 The exit tone will now sound 3 Exit the premises via an authorised exit route 4 Once the premises are secure listen from outside the protected area for the exit tone to finish Note To abort the exit enter a valid User Code Setting amp
7. he fault has been rectified 1 If the system has been programmed for Any code reset 2 With the display showing ILL CHECK Enter your User code Then press Yes The exit tone will sound and the Su Nowlin display will show 3 Enter your User code again to abort the setting The system is now reset If a Master Code Reset has been programmed by the engineer a higher level of code will be required If Alarm Reset has been programmed for Master then the display will show for example ALARM4 each time the User attempts to set Zone 4 the system Use a Master code to reset the system 1 With the display showing 11I CHECK Enter a valid Master code Then press Yes 4 2 The exit tone will sound and the Exit Now I display will show Ok 3 Enter your Master User code again to abort the setting The system is now reset If an Engineer Code Reset has been programmed please call the Installation Company If Alarm Reset has been programmed for Engineer then the display will show for example set the system 11 ALARM 4 each time the User attempts to Zone 4 If Anti has been programmed for Alarm Reset contact the Central Station or Engineer as instructed by the Installation Company and quote the number given by the display 1 The central station or
8. ng on power lines that affect your premises it might be necessary to set the system Please follow the steps outlined below III CHECK 1 With the display showing 2 Enter your User code The display III CHECK will show Mains Fit 3 Enter a your User Code again followed by Yes lt gt 4 The exit tone will now sound 5 Exit the premises via an authorised exit route Note To abort the exit enter a valid User Code If Part Setting I CHECK 1 With the display showing 2 Enter your User code The display ITIL CHECK II will show Mans El 3 Enter a your User Code again followed by 1 2 or 3 4 The exit tone will now sound 5 Retire to an unprotected area Note To abort the exit enter a valid User Code Programming User Codes Up to nine user codes may be programmed on predetermined levels These are User Numbers 1 to 3 Master Level Allows Set Part Set Unset and User Programming Mode User Numbers 4 to 7 User Level Allows Set Part Set and Unset User Numbers 8 to 9 Set Only Level Allows Set Only User Number 1 is factory default 5678 This code may only be changed there is no facility for deleting this code All other codes may be changed or deleted as required To program User Codes 1 Enter a valid Master User Code followed by No X The display will show Do You Want to Tes
9. ode followed by No X Do You Want to The display will show Test 2 Press No X The display will show Do You Want to Delete Zone 3 Press No X The display will show Do You Want to Select Options 4 Press Yes The display will show Do You Want to Program Chime 5 Press No X The display will show Do You Want to Program Codes 6 Press No X The display will show Do You Want to Set Date Time 7 Press No X The display will show Do You Want to View Log 8 Press Yes The display will show the last event in the Log Whilst viewing the log pressing No X will display the previous event Pressing Yes will display the next event Page 20 9 To return to the Unset Mode press 0 three times Note EN control panel only The the log may store up to 256 events with time and date stamp Note Non EN control panel Depending on the Log mode programmed by your installation engineer the log may store 256 events with no time or date stamp or 64 events with time and date stamp Keypad Alert DER If programmed by your installation company alarm keys fa P when pressed together will act as alert keys The exact function wil depend on what they have been programmed for If they are programmed as panic for example pressing them will activate the alarm when the sy
10. stem is set or unset Keypad Tamper The keypad will monitor the number keys that are pressed without a valid User Code being entered More than 24 key presses will cause a keypad tamper This will be displayed as CHECK and will require a valid User Code entry to stop the sounders The display will then show CHECK KP Tamper If the system was Unset only the internal sounders will operate If the system was Set a full alarm will be generated Tamper Provision is provided by the control panel for all keypads cabling and detectors to be tamper protected With the system Unset most tampers will cause an internal alarm whilst the system is Set a full alarm will be generated by a tamper Page 21 System Details installation Date Service Timer____On __ Off Next D T Notes Notes Notes RISCO Creating Security Solutions 9 y Wee Care Risco Group UK Ltd Internet www riscogroup co uk Risco Group UK Ltd reserve the right to amend the software and features without prior notice Installed By BSIA O THE BRITISH SECURITY C No INDUSTRY ASSOCIATION INVESTOR IN PEOPLE SIN480UM B PR5831 Rev1 1
11. t 2 Press No X The display will show Do You Want to Delete Zone 3 Press No X The display will show Do You Want to i Select Options 4 Press Yes 4 The display will show Do You Want to Program Chime Page 12 10 Press No X The display will show Press Yes The display will show Press a single digit corresponding to the user number 1 to 9 that you wish to program The display will show for example To change the code press No X The display will show for example To delete a code enter 0000 Enter your required code followed by Yes The display will show for example To accept the current text press Yes or To change the text press No X The display will show for example Do You Want to Program Codes Select 1 9 Code 2 4 Code 2 0000 lt Code 2 Text User 2 Code 2 Text 11 ters 12 13 Text is entered in a similar way that you would enter text on a mobile telephone Select characters from the list below 1 ABC 2 DEF 3 GHI 4 JKL 5 MNO 6 PQR Y STU 8 VWX 9 YZ blank 0 1234567890 Enter the required character followed by Yes Continue until you have entered eight charac Do You Wan
12. t to The display will show Program Codes Press Yes 4 to program more codes or Press 0 twice to return to the Unset Mode Programmable User Options Several user programmable options are available via user codes 1 2 or 3 To use these options please follow instructions below Delete Zone Option This option allows individual zones to be deleted omitted when the system is being set Note Zone delete is only effective for one Set and will need to be repeated for subsequent Sets If you are removing particular zones on a regular basis ask your installation company to include them in a Part Set The system will reinstate the detectors and set normally the next time you set the system 1 Enter a valid Master User Code followed by No X The display Do You Wantto will show Test n 2 Press No X The display will show Do You Want to Delete Zone 3 Press Yes 5 Enabled Zones The display will show 12345678 4 Press the zone numbers corresponding to the zones you wish to delete from the set procedure The display will Enabled Zones show for example 1 345 78 Page 15 5 Press 0 twice The display will show for example Do You Want to Set User 1 6 Press Yes 4 for Full Set or Press 1 for Part 1 Set or Press 2 for Part 2 Set or Press 3 for Part 3 Set
13. y not be heard depending on the system settings programmed by the installation company Exit the premises or retire to an unprotected part of the system At the end of the exit time either the exit sounder will stop if the exit tone has been audible or a single beep will be emitted if the exit tone has been silent The system is now Part Set You are free to move around the zones that have been removed by the Part Set but other zones on the system are active Unsetting the System 1 Enter the premises via an authorised Entry Point 2 The entry tone will sound 3 Proceed to the keypad and enter a valid User Code Display After an Alarm If an alarm occurs when the system is Set the cause of the alarm will be displayed for 10 seconds after you unset the system 1 The display will show for I I ALARM 4 1 example Zone 4 2 Then after 10 seconds the display III CHECK will show 3 To view the cause of the alarm again enter your User code Then press 0 Resetting After an Alarm After an alarm the system needs to be reset Your installation company will have programmed the reset modes for your system so that it complies with your insurance company and to legislation requirements Your installation company will have informed you as to the type of reset that your system is set for Before attempting to reset your system ensure that the system is Un set and t
Download Pdf Manuals
Related Search