GL7-SSD (SSD Module)
Contents
1. 49 0 6195 70060 www althen de info althen de 6 Slide the amplifier module parallel to the main module main module and connect the connector and in the same way connect the SSD module with the fixation screws 4 places on the upper and lower part A N CAUTION Slide it in the direction of the arrow Inserting it at an angle may cause damage to the nails 7 Similarly install the alarm module on the last part and fix it with Screws During installation a 4kgf cm screw tightening torque is recommended 3 Formats For first time use please format the SSD This explains the formatting procedures For details on operations etc please refer to the User s manual recorded on the CD ROM included with the main module main module When using the display module 1 Choose File Operations under File on the home screen 2 When the File Operations screen is shown select Format from Operations 3 When it returns to the File operations screen choose SSD Module to execute When a message like the one in the chart below is shown select Yes E Fre T E aed The formatting process can take several minutes When using the application software GLConfig 1 After connecting between the module and PC using USB turn on the power of the module You must have installed the USB driver previously For more information about installing the USB drive2. each amplifiers fastest speed and the same data is recorded for that interval External dimensions 49 2 x 136 x 160 mm not including protruding parts WxDxH approximate Weight 770g Vibration proof Automobile parts Type 1 Class A equivalent Depending on the state of fragmentation of the SSD there may be cases where the sampling rate won t be written on time A message will be displayed during recording If this sort of event occurs please backup important data to another media and format the SSD GRAPHTEC Corporation July 1 2012 ALTHEN Frankfurter Strasse 150 152 65779 Kelkheim 49 0 6195 70060 wwwaalthen de info althen de
3. GRAPHTEC GL7 SSD UM 151 GL7 SSD GL7000 SSD Module USER S MANUAL Thank you very much for buying this GRAPHTEC product This product is a stand alone module for recording Please use it by installing it on the main module These directions describe preparations and cautions before measurement For the details concerning operation procedures etc read the User s manual recorded on the CD ROM included with the main module Confirmation of the exterior After opening the package please confirm that there are no problems scratches and dirt on the exterior before use Confirmation of the attached items e User s manual this book 1 If by any chance faults are found please contact the store where you bought the item Please note that items mentioned in this book may change without prior notice 1 Part Names Explanation of the module s part names and functions 2 Module fixation screw Upper part 1 Module connector 3 Access Lamp 4 Module fixation screw Lower part 1 Module connector Connector for connecting all kinds of modules 2 Module fixation screw Fixation screw for the adjoining module Upper part To prevent drop off do not remove from the module 3 Access Lam ccccseeeees During data access it lights up green Not lit when normal operation Please do not turn off the power when it s lit up 4 Module fixati
4. on screw Fixation screw for the adjoining module Lower part AALTHEN Frankfurter Strasse 150 152 65779 Kelkheim 2 How to Install Module This explains how to attach the module to the main module AN CAUTION When installing or removing the module please make sure that the power is off 1 Remove the fixation screws 4 places on the upper part and lower parts place the alarm module parallel to the main module and slide it in the direction of the arrow 1 Remove the fixation screws from the 2 places on the lower part 2 Loosen the drop off prevention screws on the upper part in 2 places 3 Removing the alarm module N CAUTION Slide it in the direction of the arrow If you pry it at an angle there is a risk of damaging the connector 2 Remove the SSD module s fixation screws 2 places on the lower part e Oz O 3 Slide the SSD module parallel to the main module and connect the connector SSD module must be connected to main module N CAUTION Slide it in the direction of the arrow Inserting it at an angle may cause damage to the nails Connector 4 Fix the SSD module and the main module in place with the screws 4 places on the upper and lower parts 5 Remove the amplifier module s fixation screws 2 places on the lower part Here we explain using the Voltage Module as an example ar 8
5. r see the User s manual of the USB driver included CD ROM 2 Using Start on the Windows OS select All Programs gt Graphtec gt GL Connection GLConfig to start the GLConfig When using Windows 7 3 Press Load button to connect to the module Select SSD Module in the items of the initialization and then press Execute button Vial a ia i LEH Peeve An ees Ei ie F fine i Ei a LiF ipa Hipi ES i Bi J lier rm i t yerby EEIE Hoda al ag i ee aie Poo i ee i FIE i Fan mar oar DMa it Wi pi Fisiaas erie iii D Her T il Tu i E Eam iia ik Giri ere i fife Adiera Ho Bet 1h iri Ba r Law aye a E ia a Pees ilies i ey 4 Do you want to format message is displayed Select lt OK gt Initializing message is displayed When the formatting is completed the following screen is displayed It may take a long time to format depending on the contents of the drive abs ort wou ae 4 Specifications GL7 SSD SSD Module specifications a 2 5 SSD HDD SATA I F Sampling interval Module 1 to 2 1us at the fastest Module 3 to 4 2us at the fastest Module 5 to 10 5us at the fastest Depending on the amplifier in use there may be limitations to the sampling interval The fastest amplification is limited to the amplifier in use If a sampling interval that exceeds the fastest speed on each amplifier is set the sampling is set to
Download Pdf Manuals
Related Search