Drawer lock
Contents
1. malfunction Avoid doors which are pre loaded with a rubber profile Intended use Authorised opening of an electronic lock in wooden furniture with an encoded chip This chip can be in the form of an ID card cheque card format or key fob Function of the lock is only warran ted when mounted on not conductive materials wood plastic The max thickness of the material must not exceed 20 mm If used with higher material thickness or metal doors or doors with metal coatings an external antenna must be used Forseeable misuse Use of the lock in explosive environments Use of the lock outside of the stipulated specifications For damage resulting from incorrect use the customer bears sole responsibility the manufacturer accepts no liability whatsoever Conversions or modifications Any type of modification to the drawer lock RFID125kHz is not permitted The electromagnetic conduct of the drawer lock RFID125kHz may be impaired by additions or modifications of any kind Therefore do not carry out any modifications or additions to electric electronic components Replacement and wear parts and process materials The use of replacement parts from third party manufacturers may lead to dangers Use only original parts or parts approved by the manufacturer Drawer lock RFID125 kHz Installation and Usermanual Obligation of the user The user undertakes only to allow persons to work with the drawer lock RFID125kHz who e2. have been instructed in working with the drawer lock RFID125kHz e have read and understood this user s manual Warning signals of the drawer lock RFID125kHz The lock is equipped with a 3V battery which guarantees up to 20 000 openings The battery level is automatically checked if no opening by radio signal has taken place within 30 days If the battery level is low or the 20 000 openings have been exceeded the necessary battery replacement is indicated by an audible signal Under certain circumstances the signal may last for several days in which case automatic unlocking of the lock takes place Aim of the drawer lock RFID125kHz The drawer lock RFID125kHz is a compact wireless furniture lock for cupboards and drawers It is opened with an electric motor when closed the system locks itself Contactless chip technology is used as the key The system is woken up and opened by contactless identification via an authorised ID medium on the door The ID medium is simple to programme or delete The installation of the lock with the springpo wered door opener is possible without drilling holes in the piece of furniture Functional description Authorised opening of an electronic lock in wooden furniture with an encoded chip ID medi um This chip can be in the form of an ID card cheque card format or key fob Components of the drawer lock RFID125kHz The set contains the following components e Drawer lock with
3. Technical specifications of the drawer lock RFID125kHz Mechanical specification Weight per Set Complete Set 200 Gramm Electrical specifications Equipment class as per Class 2 Directive 1999 5 EC oF HF radiation output max 66 dBuA m at 10m Frequency band 119 to 135 kHz CP atterv vp OR 123A 3V Ambient conditions Operating temperature 5 C bis 35 C 41 F to 95 F C 4 Relative humidity operation 20 bis 75 not condensing Disposal A Danger The electronics of the drawer lock RFID125kHz contains a lithium ion battery Dispose of this battery in accordance with national regulations When disposing of partly discharged batteries ensure that no accidental short circuits can occur between the poles of the battery for example due to key fob in pocket of clothing danger of explosion and fire Fasten the partly discharged battery for transport using non conductive adhesive film in such a way that no short circuits can occur VS vr Z Important Separate electronics of the drawer lock RFID125kHz from the other parts and dispose of in accor dance with local regulations and directives Warranty conditions This product was designed and manufactured carefully At the moment of purchase the warranty amounts 12 months for material and manufacturing failures The warranty starts with the date of purchase for 12 months The product can be exchanged prior to certification of the proof of pur chase The warr
4. able from the front of the cabinet of at least 5 10 mm The mounting distance between two locks should be approx 20 cm There is otherwise a risk of interference of the fields of the card reading panels That can cause discharge of the battery
5. anty conditions are limited to costfree exchange of the product or repair Costs and risks caused by transport installation or de installation of the product and all other costs caused by the repairing will not be compensated Liability for consequential loss no matter which type are strictly excluded Congratulations on your purchase of the drawer lock RFID125kHz With this decision you have acquired locking technology with which you can lock and secure furniture without a key but nevertheless in a controlled safe way The user s manual must be accessible for operators In addition general and local regulations on accident Q Important prevention and environmental protection are to be obser ved General safety instructions Q Important If the door is closed when starting up or changing the battery without inserting the battery the door cannot be opened via radio signals it is necessary to break the door open Follow the exact instructions for installation and start up of the radio systems and replacement of the batteries Remove the flat battery and to prevent a malfunction wait at least 30 seconds before inserting a new battery Observe correct polarity at the battery case and the battery itself Q Important During installation of the lock and strike plate ensure that the door is not pre stressed and stresses are not transferred to the locking system There is a risk that the latch can no longer open gt
6. changeable case closing part with break 2 pc pins for closing part Battery CR123A 125 kHz programming card Transponder 125 kHz Stickers with Logo 8 pcs screws Tool to replace the case Manual Drawer lock RFID125kHz installation Program the drawer lock RFID125kHz When unpacking check whether the components as per the description are present On delivery the lock is neutral Programming can be carried out altered at any time as described Dispose of the packaging in accordance with the applicable regulations of your country in the following Standard configuration means wheater the programming card nor the transpon der is programmed The audible signal is on and the mode standard is activated Insert battery automatically closing of the latch The programming procedure as described in the following can be done changed at every time 1 Normally the battery compartment is already open the cover with screws is contained in an accessory bag Otherwise open the battery compart 1 Store programming card press the programming button of the lock for 3 seconds until a long ment by unscrewing the two M3x6 screws signal tone and immediately afterwards a ticking is audible for approx 7 seconds During the 2 Remove the battery from the blister pack ticking you must hold the programming card against the card reader panel until a confirmation 3 Insert the battery into the battery compartment Observe correct polarity tune is au
7. deleted Screwing holes 5 Open the latch e g with programming card and hold the latch in this position Put the pro SE gramming card 4x to the card reader panel The latch will hold open until a authorised transpon der will reset the hold open function Programming button gt All saved transponders are stored the latch is moved into the open position 6 Delete all stored transponders hold the programming card 5x against the card reader panel until a long confirmation signal is sounded gt All saved transponders are deleted the latch is moved into the open position Spezial programming 7 Switch signal tone on or off keep the programming button pressed for max one second connector gt The signal tone is switched off on a Note The lock can be operated in two modes Card reader panel Mode Standard latch function Only programmed transponders can lock unlock the drawer lock After the identification of an authorized transponder the latch moves to the open position and then moves back automatically to the closed position The programming button has two functions P Mode open closed bolt function After the identification of an authorized transponder the latch moves to the open position and stops in this position At the next identification of the authorized transponder the latch moves to the close position and stops in this position 1 For transponder signal on off gt short press 2 Creating a prog
8. dible gt The programming card is now stored Note When using a new programming card the memory will be erased long signal If the programming button has been pressed too short the lock begins to tick and an alarm will sound You have now turned the identification signal off see point 6 2 Store transponder hold the stored program card once against the card reader panel gt A ticking is audible for approx 7 seconds During the ticking hold the transponder key fob against the card reader panel to read it in until a confirmation signal is sounded 2 x 3 short beeps gt The transponder is now stored 3 Check transponder for function hold the transponder once against the card reader panel gt The confirmation signal is sounded again the latch moves back and the lock opens Repeat the process 2 to 3 times to store further transponders You can teach at maximum 1 program ming card and 50 transponder at once The programming card and the transponder can be teached in at several other locks 4 Screw on the battery case cover with the M3x6mm screws provided gt The device is ready for programming 4 Delete stored transponders individually hold the programming card once against the card reader panel A ticking is heard for approx 7 seconds During the ticking hold the transponder Drawer lock RFID125kHz general survey shel aol card crea ina delete it until a confirmation signal is sounded e transponder is
9. ramming card gt long press until long beep Install drawer lock RFID125kHz on furniture body and door Blende EEC Declaration of Conformity in accordance with the directives Schubladenboden Blende 2004 108 EC Directive on electro magnetic compatibility EMC 1999 5 EC 1999 Directive on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity R amp TTE 2002 96 EC 2003 Directive on waste electric and electronic equipment WEEE 2011 65 EC Directive on the restriction of the use of certain hazardous s substances in electrical and electronic equipment recast Q Important u Assembling distance for the product Drawer lock RFID125kHz 4 ca 20 cm ol e p o per Q Important RFID Card reader distance Key fob up to 25mm Transponder card up to 40mm The following harmonised standards are applied EN 300330 2 V1 3 1 2006 EN 301489 3 V1 4 1 2002 EN ISO 12100 2010 EN 50364 2010 Check reading distance after assemb ling the drawer lock RFID125kHz The lock assembly of furniture and the closing part must always be mounted so that the door in the closed state has at least 0 5 mm di stance This tolerance is necessary for the emergency opening in case of the low battery Make sure that the transponder used have a very good reading quality There should always be a comfortable reading distance be avail
Download Pdf Manuals
Related Search