instruction manual
Contents
1. synchronized light show This function is good when you want an instant show You have to set the first unit in master mode and select Eh Glrandom show Shi i show 1 or or show 12 and speed Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to select normal or Bi d 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on 2 light show In slave mode means the unit works as the master unit and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 4 2 Easy Controller by CA 8 The easy remote control is used only in master slave mode There is a terminator for connect the easy controller inside the fixture By connecting the cable into DMX IN waterproof cable entry gland to the CA 8 terminator of the first fixture you will find that the remote control on the first fixture will control all the other fixtures for Stand by Function and Mode functions Blackout Blackout the unit 1 Sound White Strobe Select Show Function 2 Sound Color Strobe Show 1 12 Sound Strobe Show e LED OFF LED ON Controller 9 4 3 DMX Controller Using universal DMX controller to control the units you have to set DMX ad2. 3 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 Each lighting fixture needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 5 3pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin4 5 not used 7 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture does not work no light 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some fix
3. 67 Chase 3 ee sacar Chasa eee 021 041 Pattern 2 021 041Chase 2 525 954 B 10 281 Chase 4 000 020 Pattern 1 000 020 Chase 1 018 034 G 0 9L OFF 000 017 R 256 CH mode DMX512 Configuration Ch253 Ch254 Ch255 Ch256 Red Green Blue white Red Green Blue White 255r 100 255r 100 255r 100 255pr100 255r 100 255r100 255r 100 255r100 4 channels as a group please refer to the DMX configuration of 1 4 channels to control the other channels when you choose 256 channels mode Under this mode you can control the 256 LEDs separately 6 DMX512 Connections The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels COMMON DMX INPUT DMX OUTPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 11 2 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected
4. LED 7871 User Manual Please read the instructions carefully before use 1 Safety Introductions A N Please read the instructions carefully which includes important TABLE OF CONTENTS WARNING e Please information about the installation operation and maintenance keep this User Manual for future consultation If you sell the fixture to another user be 1 Safety Instructions sure that they also receive this instruction booklet Seed e Unpack and check carefully there is no transportation damage before using the fixture 2 Technical Specifications e s important to ground the yellow green conductor to earth in order to avoid electric shock 3 How To set The Fixture e Disconnect main power before servicing and maintenance e Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this 4 How To Control The Fixture e Inthe event of serious operating problem stop using the fixture immediately Never try 5 DMX 512 Configuration to repair the fixture by yourself Repairs carried out by unskilled people can lead to l damage or malfunction Please contact the nearest authorized technical assistance 6 DMX 512 Connections center Always use the same type spare parts e Do not connect the device to any dimmer pack f Troubleshooting e Do not touch any wire during operation and there might be a hazard of electric shock e To prevent or reduce the risk of electrica
5. d Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements 14 Innovation Quality Performance 15
6. dress from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again If you use please refer to the following diagram to address your DMX512 channel for the first 4 2 units 256 channels uiaiia 5 DMX512 Configuration 1 amp 4 CH modes DMX512 Configuration chs Cha Pattern Chase Color Chase Speed CH1 10 99 CH1 100 239 CH1 10 99 CH1 100 239 Strobe 239 255 R G B W Random 255 240 255 Chase 236 255 Pattern 12 236 255 Chase 12 222 238 G B W 218 239 ive 215 235 Pattern 11 215 235 Chase 11 595 591 R B W 198 217 194 214 Pattern 10 194 214 Chase 10 188 204 R G W 178 197 173 193 Pattern 9 173 193 Chase 9 171 187 R G B 158 177 oe 151 172 Pattern 8 151 172 Chase 8 154 170 B W Fast 138 157 130 150 Pattern 7 130 150 Chase 7 137 153 G W a ao 109 129 Pattern 6 109 129 Chase 6 120 136 G B i ai 10 99 088 108 Pattern 5 088 108 Chase 5 103 119 R W 88 107 Chase 5 Pattern 68 87 Chase 4 066 087 Pattern 4 066 087 Chase 4 086 102 R B a 042 065 Pattern 3 042 065 Chase 3 02 08 R G 48
7. l shock or fire do not expose the fixture to rain 8 Fixture Cleaning or moisture e The housing must be replaced if they are visibly damaged e Do not look directly at the LED light beam while the fixture is on e There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs by yourself In the unlikely event your fixture may require service please contact your nearest dealer e Due to the magnifying type lens please keep the lens out of contact with direct sunlight Direct sunlight can cause heat to build up inside of the unit which will seriously damage unit For power supply do not connect in series much more than 20 units use another mains supply for next 20 units 2 Technical Specifications e The Matrix 4 LED features 4 high brightness red green blue and white LEDs clusters cresting stunning text patterns geometric figures dynamic scanning rolling and rotating effects e Great built in lighting shows under Master Slave operation triggered by music e Optional CA 8 easy controller for enjoying instant lighting shows at you fingertips e LED display for easy navigation e input Voltage 100V 240V 50 60Hz e Power consumption 29W e LED Total 256pcs Red 64pcs Green 64pcs Blue 64pcs White 64pcs e Dimension 270 x 242 x 317mm e Weight 3 8 kgs 3 How To Set The Fixture 1 Display To show the various menus and the selected functions LED Butto
8. n MENU To select the programming functions UP To go forward in the selected functions Q ENTER To confirm the selected functions T Sensitivity Adjust sensitivity of the sound control T DOWN To go backward in the selected functions E Microphone Receive music for the sound active 42 Only for remote control By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode function E DMX output For DMX512 link use 3 pin XLR plug cable to link the next unit E DMX input For DMX512 link use 3 5 pin XLR plug cable to input DMX signal 5 Mains output Connect to supply mains power for the next unit T Mains input Connect to supply mains power 5 3 2 Main Function To select any functions press MENU button until the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press ENTER button to setup or it will automatically return to the main functions without any change after idling 10 seconds Back to the functions without any change press MENU button The main functions are shown below DMX512 Address Setting Channel mode Master Mode Slave Mode Normal Slave mode 2 Light Show Random Show Show mode 1 12 MENU on Sound Mode on Solin oF F Sound Mode off ccna HOS Blackout Mode Yes Blackout io Blackout Mode No Blackout LED o
9. n LEd aff LED off ararH e Normal 5 iE Inversion Self Test FL S Fixture Hours LE Software Version DMX 512 Address Setting Press the MENU button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX 512 address Once the address has been selected press ENTER button to setup or automatically exit menu mode without any change after 10 seconds Back to the previous functions without any change press MENU button r nee LIHI Channel Mode H e Press the MENU button up to when the LAO is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 1 channel or 4 channels or 256 Channels mode Once the mode has been selected press the ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button Slave Mode Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the master or slave 1 or Slave 2 mode Once select press the ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button HS Show Mode Press the MENU button up to when the Shiid is shown on the display Pressing ENTER button U
10. ormal or inverse press ENTER button to setup Back to the functions without any change press MENU button E i ot Lt Il Self Test Press the MENU button up to when the teot is blinking on the display Pressing ENTER button and the unit will run the built in programmer for self test To go back to the functions press the MENU button t 4 Fixture Hours Press the MENU button up to when the Far button and the display will show the number of working hours of the unit To go back to the is blinking on the display Pressing ENTER functions press the MENU button Software version Press the MENU button up to when the is blinking on the display Pressing ENTER button and the display will show the version of software of the unit To go back to the functions press the MENU button again 4 How To Control The Fixture You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 7871 on the display After that the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated
11. se DOWN and UP button to select the Random show or show 1 or Show 2 or or show 12 Once select press ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button Sound Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the sound on or sound off Once select press ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button Blackout mode Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the blackout or normal Once select press ENTER button to setup or automatically exit menu mode without any change after 10 seconds To go back to the functions without any change press the MENU button T 1 Oo Ltt LED display Press the MENU button up to when the Led is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select display on or oF Fldisplay off mode Once select press ENTER button to setup or exit menu mode without any change after 10 seconds Back to the functions without any change press MENU button again Display Inverse Press MENU button until is blinking on the display Use DOWN and UP button to select n
12. tures don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the 12 master slave mode signal 2 Wrong DMX address in the fixture Set the proper address D No response to the sound 1 Make sure the fixture does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 8 Fixture Cleaninc The cleaning of internal must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonize
Download Pdf Manuals
Related Search