EKT User Manual_3pg_JS 10-31-12 - Web Layout
Contents
1. User Manual Electronic Key Tether ekt Model 3000 Never Lose a Set of Master Keys Again www sStopKeyLoss com TROUBLESHOOTING amp WARNINGS This equipment generates uses and can radiate ra dio frequency energy and if not used in accordance with the instructions may cause harmful interfer ence to radio or television reception which can be determined by turning the unit on and off The user is encouraged to attempt correcting the interference by increasing the separation between the ekt units and the affected device or consult Tether Technolo gies for technical help Refer to http www access gpo gov nara cfr cfr retrieve html page 1 Title 47 CFR Part 15 Section 105 Caution Changes or modifications to ekt s RF hardware that are not expressly approved by Tether Technologies Inc could void the user s authority to operate the equipment and product warranty NOTICES OF COMPLIANCE This equipment has been tested and found to com ply with the limits for a Class B digital device pur suant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential commercial use environment PRODUCT WARRANTY amp SUPPORT Your ekt Model 3000 is covered by a limited war ranty To be eligible you must register your ekt within 30 days of purchase at www stopkeyloss com warranty In brief Phone 234 206 0304 www stopKeyLoss com ekt The2. the key ring is at the bottom of the key unit Fit the top edge of the key unit into the groove of the belt unit at a slight angle away from the user s body Push the key unit down and toward the belt unit until it clicks and locks securely in place To remove the key unit from the belt unit i Grasp the keys with the inside of your hand at the same time using your thumb press the gray button and pull keys up and away from the body TRA As the units separate the strobe light on the key unit will flash one time indicating both units are active and alarms are set If alarm signals begin immediately check unit serial numbers to ensure that they match If they continue to signal re place batteries Then contact customer support ALARM SIGNALS If the key unit and the belt unit are separated by more than 10 15 steps four alarms will start 1 The belt unit emits a strong vibration and audi ble chirp alarm 2 The key unit emits an 85 decibel audio alarm and a bright LED strobe light All warning alarm signals continue until the key unit is safely reattached to the belt unit REPLACING BATTERIES Your ekt runs on standard AAA batteries with an average life of 6 months When 80 of batteries power is spent a chirp alerts users that they need to be replaced It is recommended that you replace batteries in both the belt and key units at the same time to ensure continuity Using a Phillips scre
3. warranty covers any defects or malfunctions in your new ekt The warranty lasts for a period of one year from the date of purchase Tether Technologies will replace any defective or malfunctioning part or if the unit is deter mined to be non repairable provide you with a replacement ekt all at no charge Batteries or any problem that is caused by abuse misuse or an act of God such as a flood are not covered Also consequential and inci dental damages are not recoverable Some states do not allow the exclusion or limitation of inci dental or consequential damages so the above limitation or exclusion may not apply to you TETHER TECHNOLOGIES INC 24 Roy Street Suite 25 D T Seattle WA 98109 M Understanding amp Using Your ekt Your ekt has three parts The key unit A which holds the key ring The belt unit B which securely attaches to any belt or utility belt P Q E C Key ring C sold separately To attach belt unit to belt or utility belt L 2 Place the metal clip inward or towards the user s body onto the top of the belt Push down until metal clip fits snug ly around the belt and belt is com pletely within metal clip When secured the metal clip should form a loop around the belt to pre vent it from sliding up and off the belt To attach key unit to belt unit L First make sure the gray button is facing outward or away from the user s body and that
4. wdriver remove the two screws on the back of the belt unit and back of the key unit Once the screws are removed the backs will come off Replace batteries and screw the backs onto both units
Download Pdf Manuals
Related Search