LASER INSERT
Contents
1. RT 12 GAUGE PUMP ACTION SHOTGUN VER 1 0 TABLE OF CONTENTS IV APPENDICES 41 Disassembly The reader should take the following steps in order to properly disassemble the shotgun insert 1 Unscrew the laser housing Item 8 from the striker housing Item 1 See Fig 05 below Fig 05 Unscrew the laser housing LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN VER 1 0 PAGE 11 TABLE OF CONTENTS 2 Remove the laser housing and note the current orientation of the battery pack as this will aid in troubleshooting reference Section 3 1 See Fig 06 below Ensure that the raised portion of the battery pack is pointed toward the laser housing negative side up Fig 06 Removing the laser housing with proper orientation 3 Remove the 4 Cell battery pack by tipping the striker housing over with one hand and dumping the 4 Cell battery pack out into the other See Fig O7 to the right Fig O7 Tip the striker housing to remove battery pack PAGE 12 LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN VER 1 0 TABLE OF CONTENTS V CONTACT VIRTRA The contact information below should be used for additional help in troubleshoot ing Current issues as well as the location for sending any items in need of repair VirTra Attn Service Department 7970 S Kyrene Rd Tempe AZ 85284 USA Telephone 480 968 1488 x5029 After hours 602 456 9173 E mail service virtra com Website wwwvvirtra com If any of the components m2. Service and Support VirTra Attn Service Department 7970 S Kyrene Rd Tempe AZ 85284 USA Telephone 480 968 1488 ext 5029 E mail service virtra com WWW VIRTRA COM 2012 VirTra All Rights Reserved Trademarks and trade names are property of their respective owners 0712 LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN V 1 0 Vir Tra WWW VIRTRA COM VirTra Inc shall not be liable for any incidental or consequential damage resulting from the performance or use of this product This company makes no representations or warranties regarding the contents of this man ual Information in this manual has been carefully checked for reliability however no guarantee is given as to the correctness of the contents In the interest of continued product improvement this company reserves the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes The information contained in this manual is provided for general use by the customers of the product COPYRIGHT Copyright 2012 by VirTra Inc All Rights Reserved No part of this publication may be reproduced transcribed stored in a retrieval system translated into any language or transmitted in any form or by any means electronic mechanical magnetic optical chemical photocopying manual or otherwise without prior written permission fro
3. aking up the 12 Gauge Pump action Shotgun Insert Ver1 0 are in need of repair service the following steps are necessary to have the desired repairs or service properly completed 1 Consult Section Ill and Section IV of this manual first before contacting VirTra 2 If problems persist contact VirTra Service Department via email or phone and obtain a Return Authorization RA number Save the RA number someplace convenient as you will need to use it to fill in the Reference Number field in the Service Request Form SRF found below 3 Fill out the remainder of the Service Request Form and include a paper copy in package of all items being returned An electronic copy of the Service Request Form can be saved by printing the completed document to PDF Please Scan QR Code to download the Service Request Form or visit http wwwvirtra com PDF ServiceForms VirlraServiceForm pdf LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN VER 1 0 PAGE 13
4. ell Battery Pack O Laser House NOTE Rubber type O rings are shown on items 1 and 8 but have not been assigned separate item numbers Item 7 is comprised of Qty 4 individual 392 coin cell batteries that can be purchased from a variety of retail outlets The item numbers assigned to the parts in the previous and following exploded views are for the purposes of this document ONLY and should not be used for the purpose of ordering replacement parts PAGE 6 LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN VER 1 0 TABLE OF CONTENTS Il USE IN SHOTGUN STOP Must read to the end of the paragraph before proceeding Ensure that the shotgun for use with the 12 Gauge Pump action Shotgun Insert is clear of ANY shotgun ammunition live or otherwise Visually inspect the chamber of the shotgun by pulling the action of the shotgun back toward the butt of the gun Ensure that no ammunition is in the chamber or magazine tube awaiting insertion into the chamber If any ammunition is present in the chamber or magazine tube gently remove it with your fingers At this point the user should reference the user manual of the shotgun manufacturer if he or she does not feel comfortable performing the above operations Figure 01 below depicts how the 12 Gauge Pump action Shotgun Insert referred to as the shotgun insert from here on out should be inserted into the 12 gauge shotgun Insert into chamber of shot gun so that the word UP is pointed toward
5. m VirTra Inc DISCLAIMER VirTra Inc shall not be liable for any incidental or consequential damage resulting from the performance or use of this product This company makes no representations or warranties regarding the contents of this manual Information in this manual has been carefully checked for reliability however no guarantee is given as to the correctness of the contents In the interest of continued product improvement this company reserves the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes The information contained in this manual is provided for general use by the customers of the product TRADEMARKS Product names used in this manual are ascribed to their respective owners and acknowledged TABLE OF CONTENT TABLE OF CONTENTS l EXPLODED VIEW y H aaaaa 6 llI TROUBLESHOOTING Zaa 8 31 No Shots Register on Screen o 8 3 2 The Shotgun Insert is Being Extracted 8 41 Disassembly y aaaaaaaaaaa A V CONTACT VIRTRA y yy Y aaaa 13 LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN VER 0 PAGE 5 TABLE OF CONTENTS I EXPLODED VIEW ITEM NUMBER ITEM NAME IEEE E AES re ey tr Striker Housing DE a E E teens Rear PCB E EE ETAS Tapered Battery Spring a E E E E EE Pogo Pin Spacer De a Pogo Pin S EE E ETE EN Battery Sleeve A E EEE T 4 C
6. r warranty please follow the steps outlined in page 13 for properly submitting a service request 3 2 The Shotgun Insert is Being Extracted If the shotgun insert is being ejected like a standard round of shotgun ammunition then please follow the steps below to try and remedy this issue 1 Ensure that the shotgun insert is properly oriented in the chamber of the shot gun The word UP engraved into the back of the shotgun insert should be pointed toward the sky See Fig 02 below CORRECT INCORRECT Correct orientation of shotgun insert Incorrect orientation of shotgun insert D q p Fig 02 Proper Orientation PAGE 8 LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN VER 1 0 TABLE OF CONTENTS 2 Lastly ensure that the shotgun insert has two flat cutouts on opposite sides see Fig 03 below Two flat cutouts Fig O3 Two flat cutouts LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN VER 1 0 PAGE 9 TABLE OF CONTENTS Figure 04 below is an image of a shotgun insert that only has one cutout One flat cutout Fig 04 One flat cutout If the reader has a shotgun insert with a single flat cutout that continues to be ejected even after being oriented correctly then the reader is using a shotgun that requires a shotgun insert with two flat cutouts Please contact VirTra s Service Department see page 13 for help in exchanging the single flat cutout for a double flat cutout shotgun insert PAGE 10 LASER INSE
7. sky UP 3 Fig 01 Correct way to insert Laser end must be pointed down the barrel of the shotgun LASER INSERT 12 GAUGE PUMP ACTION SHOTGUN VER 1 0 PAGE 7 TABLE OF CONTENTS III TROUBLESHOOTING 31 No Shots Register on Screen If no shots register on the screen with the shotgun insert properly inserted in the chamber of the shotgun please follow the steps outlined below to try and remedy this issue 1 The first item to verify is whether or not the batteries are properly oriented Section IV Appendices 2 Second if the batteries were properly oriented then replace the 4 Cell battery pack with a new 4 Cell battery pack and properly dispose of the old 4 Cell bat tery pack Reassemble and test the shotgun insert on a VirlTra simulator If it is working properly then return the shotgun insert to normal operation If it is still not working proceed to step three below 3 Ifyou are at this step that means there is a possibility that the firing pin of the shotgun has worn down to the point that it can no longer strike the shotgun insert Follow the instructions of the shotgun manufacturer for removing in specting and replacement of the firing pin If according to the guidelines of the manufacturer the firing pin did not have to be replaced or it was replaced and the shotgun insert still does not work properly then the shotgun insert will have to be sent back to VirTra for repair If the shotgun insert is still unde
Download Pdf Manuals
Related Search