CTX PR711FL Computer Monitor User Manual
Contents
1. If this window appears that means it cannot be preset factory mode only User mode No Preset PR711FL User s Manual Confirm the Recall action by pressing the or cancel the action by pressing the ESC Confirm Enter YES ESC NO G Language Press amp or to select the Language for OSD only Deutsch Fran ais Espa ol Italiano 2 Contrast Brightness When OSD is off or will be adjust contrast or brightness Trouble Shooting PR711FL User s Manual Notify your supervisor or contact your service personal when e Power cords are frayed or damaged e Liquid is spilled into the monitor e The monitor does not operate normally when operating instructions are observed e The monitor has been dropped or the cabinet has been damaged Review this list of trouble shooting tips before contacting an authorized service center Problem What to do Power Indicator LED is not lit No Picture No Signal Input No Signal Input Make sure Power control is in the ON position Check the power cable It must be plugged in completely If the Power Indicator is amber colored your computer has sent the monitor into its Power Save mode See Energy Declaration The video card may not be seated properly Make sure it is fully seated in its slot Make sure the signal cable is connected securely to the video card or computer Enable Power Save function PR72. of your monitor Front Panel Controls 1 Power Switch To turn the monitor on or off 2 Power LED Indicator As long as the monitor is powered this indicator is lit In normal operation it lights green While in power saving mode the indicator will turn to amber 3 Enter button To display the OSD manual and selected function PR711FL User s Manual 4 Up button To adjust the selected OSD function or the contrast directly 5 Down F button To adjust the selected OSD function or the brightness directly 6 ESC button To close the OSD manual and to escape function How to Make On Screen Display OSD Adjustments On Screen Displays are called up from the front panel controls as noted above Adjustments are made with H and ESC control switches Power Saving Note This monitor is equipped with an automatic power saving circuitry design that will work with any computer which meets the VESA DPMS standard It meets the ENERGY STAR low power state definition OSD On Screen Display Controls 1 Press to open the On Screen menu function Seven adjustment functions will appear on the On Screen menu Press 4 or button to scroll selections from top down sequence as below Press to enter the item which is selected or to activate the preferred adjustments Press ESC to exit the On Screen Menu or up level PR711FL User s Manual A Status To display exis
3. 6 7 8 10 11 No Connection 9 9 SDA DDC 12 SCL DDC 15 21 PR711FL User s Manual Preset Timing Chart Note This monitor is equipped with a microprocessor which allows the user to set his own preferred mode s beyond those standard mode listed below To reduce visual tiredness and eyestrain it is recommended to choose the highest refresh een mi sotso eore vor ft fw ene ef 800x600 5Hz VESA E SEE E 832x624 5Hz MAC 49 7 75 e e a 1024x768 85Hz iaai iia aa modes available ew ee 1280x1024 5Hz VESA 22
4. Manual Specification Color Picture Tube 43 1 cm 17 16 viewable screen size diagonal measurement 90 degree deflection FD Trinitron CRT anti glare anti reflection anti static medium short persistence phosphor dark bulb AG Pitch 0 24 mm at center Input Signal Analog 0 7V peak to peak separate TTL Positive or Negative Scan Frequency Horizontal 30 to 97 kHz automatically Vertical 50 to 160 Hz automatically Max Resolution 1600 x 1200 pixel non interlaced Display Colors Analog input unlimited colors Pixel Rate 202 MHz Plug amp Play DDC 1 DDC 2B Power Supply 100 240 VAC 50 60 Hz automatically Power Consumption 100W max Dimensions 412 W x 415 H x 430 5 D mm Weight 20 1 kgs G W 17 6kgs N W Environment Consideration Operating Temperature 0 C to 35 C Humidity 20 to 80 Storage Temperature 0 C to 60 C Humidity 10 to 90 Note Specifications are subject to change without notice 20 PR711FL User s Manual Reference Information This color monitor supports multiple operating platforms such as IBM compatible and Macintosh family computers This section provides you with detailed information on pin assignment of the D Sub connector and the preset timing chart of the prevailing video standards Connector Pin Assignments Male Mini D 15 Connector Signal 15 Pin Mini D Sub Red Video 1 Green Video 2 Blue Video 3 Horizontal Sync 13 Vertical Sync 14 Ground 4
5. 11FL User s Manual Readjust the signal based on spec Reference Signal Out of range Scan Frequency Signal out of range 40 5 KHz 120 0Hz Display image is not centered or Refer to Controls amp Adjustments You need to is too small or too large adjust Size and Position of the image Image is scrolling or is unstable Make sure the signal cable is connected securely to the video card or computer Picture is fuzzy or color looks Adjust Contrast and Brightness controls blotchy On all Models select the Degauss function in the OSD control menu CAUTION Allow a minimum of 20 minutes to elapse before depressing Degauss button again when not switching between modes DO NOT HOLD THE BUTTON DOWN CONTINUOUSLY Picture bounces or a wave Move devices that might be causing electrical pattern is present interference away from the monitor See FCC Information PR711FL User s Manual Refer to Controls and Adjustments You need Edges of display are curved inward or outward to adjust the Side Pincushion No Plug amp Play Verify that the host system is Plug amp Play compatible Check to see if Windows is installed and the software key for the Data Display Channel DDC function is enabled Determine if original manufacturer s detachable signal cable is being used D Sub 15 pin only Our monitor is build in FD Trinitron CRT This CRT is s
6. PR711FL User s Manual 4 User s Manual PRZIIFL PR711FL User s Manual Table of Contents Safety Instructions 3 Recommendation for Optimum Performance 5 Introduction 6 Installation 7 Controls and Adjustments 9 Trouble Shooting 14 Energy Declaration 18 Specification 19 Reference Information 20 PR711FL User s Manual Safety Instructions FCC Statement This equipment has been tested to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning If a shiel
7. ded type power cord is supplied with this monitor it is required in order to meet FCC emission limits and to prevent interference with nearby radio and television reception Only shielded cables should be used to connect I O devices to this equipment You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment CE Statement This device complies with the requirements of EMC Electromagnetic Compatibility and with Low Voltage directive Safety Precautions Always observe these important safety instructions 1 Allow adequate ventilation around the monitor so that heat can be dissipated properly Do not block or cover ventilated openings Do not place the monitor in an enclosure that will obstruct the free flow of air PR711FL User s Manual 2 Do not place the monitor or other heavy objects on the power cord A damaged power cord can cause fires or electrical shock 3 Keep the monitor away from high capacity transformers electric motors and other strong magnetic fields 4 Do not connect to any voltage or frequency beyond the range specified on the back of the monitor Please follow all warnings and instructions marked on the product 5 Unplug the monitor from the electrical power source before cleaning any part of the monitor Do not use liquids sprays or aerosol cleaners Clean the surface of the screen with a lint free
8. ensitive to shocks and vibrations that may occur during transportation Following are some adjustment tips when below mentioned symptoms occur Symptom Tip Two horizontal lines are visible This is normal characteristic of FD Trinitron on the screen CRT These are damper wires which are attached to the aperture grille and are designed to dampen and prevent shock and vibrate to the aperture grille PR711FL User s Manual 18 PR711FL User s Manual Energy Declaration This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling DPMS standard This means that the monitor must be connected to a computer which also supports the VESA DPMS standard to fulfill the requirements of the NUTEK specification 803299 94 96 The time settings for switching to a power saving mode are adjusted from the system unit by software From the first indication of inactivity to power saving position A2 the total time must not be set to more than 70 minutes 1 VESA Power Management Proposal H sync V sync Video State Off On Blank Stand by On Off Blank Suspend Off Off Blank Off 2 Power Consumption 120 230 Vac Power NUTEK VESA state LED indicator Consumption Normal operation On Green lt 100W Power Saving Suspend Amber lt 15W Position A1 Power Saving Off Amber lt SW Position A2 Recovery Time lt 3 Sec PR711FL User s
9. gonomic features In addition to the friendly controls and user comfort features the emission level of the electric and magnetic field is kept low to meet the Swedish MPR II or TCO standards The monitor is also equipped with energy saving functions it is compatible with the VESA power saving standards PR711FL User s Manual Installation Unpacking Y our color monitor package should contain the following items Color monitor with tilt swivel base with Signal cable wr Power cord User s Guide Driver CD System Setup 1 Turn off the system and all attached peripherals 2 Carefully turn the monitor upside down PR711FL User s Manual Remove the Tilt Swivel Base 1 Squeeze and hold the latches 2 Pull the tilt swivel base to the rear of the monitor and lift to remove the base Installing the Tilt Swivel Base 1 Align the base with the slots on the bottom of the monitor and insert the tilt swivel base into the slots 2 Push the tilt swivel base firmly toward the front of the monitor until the latches click into the locked position PR711FL User s Manual Controls and Adjustments Once installation is complete refer to this section for useful tips on how to use your monitor controls and make adjustments to match your personal preferences The following indicators controls and adjustments including On Screen Displays OSD are accessible from the front
10. non abrasive cloth and a non alcohol neutral and non abrasive cleaning solution or glass cleaner Use a slightly dampened cloth to clean the exterior of the plastic cabinet 6 This product is equipped with a 3 wire grounding type plug an important safety feature This plug will only fit into a grounding type power outlet If a grounding type power outlet is not available have one installed by a qualified electrician Do not cut off the grounding pin in order to make the plug fit into an inappropriate power outlet 7 For 230VAC operation a power cord with tandem blade plug is required Select your power cord in accordance with the safety regulations of your country For example North America UL listed and CSA certified Germany VDE certified Nordic Countries SEMKO NEMKO DEMKO or FIMKO certified 8 Do not attempt to service this product yourself Opening or removing covers may expose you to dangerous voltage points or other risks Refer all servicing to qualified service personnel 9 The plug on the power cord is intended to serve as the disconnect device The socket outlet should be installed near the equipment and should be easily accessible Notice Actual safety specifications please refer to the label on the back of monitor PR711FL User s Manual Recommendation for Optimum Performance Y our monitor will provide the best results if you follow these recommendations 1 Do not use your monitor against a bright backgro
11. ting timing data of resolution and frequency TOZA 7GB H 6824 5 kHz wW Boot Hz B Picture a Press F or amp to select Vertical and Horizontal position Vertical and Horizontal size b Press to process c Press 4 or F to preferred picture C Geometry a Press F or amp to select Side pin Balance Keystone Parallel Rotate and Corner b Press to process c Press amp or F to preferred picture PR711FL User s Manual D Color a Press F or amp to select various white color temperature standard b In User item presses to confirm action color adjustment c Press or to select Red Green and Blue then press Enter to process d Press or increase or decrease density 300 K 6500 K 5000 K User E Advanced a Press F or amp to select Moire Converge or Degauss b Press to proceed c Press 4 or F to preferred picture Converge Degauss E 1 Moire Press or to reduce Moire 12 PR711FL User s Manual E 2 Converage a Press 4 or to select Horizontal or Vertical convergence adjustment b Press to proceed R i Caution 1 If moire reduction is overdone picture quality i e focus and vertical line stability will both be effected 2 Proper adjustment is recommended for not effecting picture performance F Recall Press to confirm window Converge
12. und or where sunlight or other light sources will shine directly on the screen 2 Place the monitor just below eye level 10 15 for optimum viewing 3 Set the monitor brightness level to match the ambient room light 4 For optimum focus the contrast control should not be set to the maximum unless the input signal level is extremely low Also the brightness control should be set to a point where the overall background area just begins to disappear CAUTION e Donot scrap or knock the surface of CRT with a pen a screwdriver and so on e Clean the CRT surface with a lint free nonabrasive soft cloth and should not use the solution or glass cleaner containing corpuscles like an abrasive alcohol and an alkaline solution PR711FL User s Manual Introduction The monitor is a multiple frequency high resolution color monitor for IBM compatible PC s or Macintosh and workstation systems The monitor is equipped with microprocessor based intelligence and multiple frequency scanning capability allowing it to provide maximum compatibility for various system platforms The monitor uses the latest screen technology including a 0 24mm AG FD Trinitron CRT to display crisp text and vivid color graphics The full function digital control and On Screen Display OSD system provides easy adjustment of image geometry and color settings for different display modes with the precision of a fixed frequency monitor The monitor also has full er
Download Pdf Manuals
Related Search