s h owe r sp a - Quality Craft
Contents
1. hand shower Adjust water temperature and pressure using your existing shower valve TROUBLESHOOTING 1 Ensure rubber washers 9 13 18 20 are properly installed to avoid leaks 2 Make sure you drill holes according to the instructions and secure the panel on the bottom bracket 25 3 If you find that water pressure or volume is low clean the mesh gaskets 1 4 If there is no water flow check the brass connector as it might have been installed reversed Check step 9 of the installation guide CARE AND MAINTENANCE e After use rinse the shower column with water using the hand shower to remove any soap deposits e Never use abrasive cleaners as they will scratch the finish It is the responsibility of the installer owner to determine specific local code compliance prior to installation of the product Quality Craft makes no representation or warranty regarding and will not be responsible for any code compliance Quality Craft does not warrant connections of water supply fittings and piping or fill systems Nor is it responsible for damage to the shower panel which occurs during any installation procedure REPLACEMENT PARTS PART DESCRIPTION QTY CODE sae pack _ an Stainless steel washers 3 D wall anchors 3 mounting bracket 1 di eee GL1002 rubber washer for hand shower 2 GL1003 valve cartridge 1 Te GL1004 hand shower hose l m GL1005 hand s2. ultimate rain and Installation Guide and User Manual CIC 199 2195 Model 8TIPO04CHR G 1 ai m V 1 gt m x U m A m Z O gt I O lt m N a D lt 4 Please read and save this guide before using your shower spa Store the guide in a safe place for future reference IMPORTANT If you have any problems with this unit or there are missing or damaged parts please call toll free 1 800 459 4409 8 30am to 5 00pm EST DO NOT RETURN THE UNIT TO THE PLACE OF PURCHASE before calling the toll free number above l o oa MA w This unit is not suitable for fiberglass or acrylic showers Carefully check the unit prior to installation to ensure there is no damage Installing a damaged unit will void the warranty Do not dispose of any packaging until you are satisfied with this product Your installation must comply with all local plumbing building codes Have a qualified tradesman do or approve your plumbing installation Protect the entire surface during installation Always wear safety goggles and gloves in order to avoid personal injury TOOLS REQUIRED Adjustable wrench Carpenter s square Tape measure Pencil Electric drill Drill bit 7mm or 1 4 Phillips screw driver DANGER Do not place electrical appliances close to the shower enclosure CONTENTS A GW Po ee 565 mm 22 24 in Mesh gasket Check valve Bra
3. 3 with restrictor 6 Fig OA 12A2 With a dry rag thoroughly clean the wall between the brass connector and the shower valve 12A3 Peel the paper backing from double sided tape 28 on back of column Fig PA 12A4 Hang shower column 15 on the stainless steel mounting bracket 4 through holes in column Position column vertically level then apply pressure to main body to firmly adhere mounting tape to wall Fig QA FIG OA FIG PA FIG QA Option B Bottom bracket and screws 12B1 Mark the drill holes 14 0 635 cm as shown in Fig NB The three holes consist of two holes drilled side by side 0 67 1 7 cm apart from the center of each hole with the center line running between them The third hole is drilled on the center line 0 79 2 cm below the first two holes The upper two holes should be drilled below the shower pipe 22 14 56 5 cm from the center of the top two holes to the center of the inlet pipe 12B2 Insert wall anchors 21 in pre drilled holes Secure bottom bracket 25 to wall with screws 27 and stainless steel washers 26 Fig OB 12B3 Connect L fitting 7 to brass connector 3 with restrictor 6 Fig PB 12B4 Hang shower column bottom 15 on the bottom bracket 25 first then hang the shower column 15 on stainless steel mounting bracket 4 through holes in shower column Fig QB FIG NB FIG OB i I 0 79 2 cm U inlet 2
4. 2 14 56 5 cm 0 67 1 7 cm i 2 0 67 1 7 cm 0 79 2 cm 13 Replace top cover 10 and stainless steel cover 24 on shower column 15 Fig R 14 Attach long flexible shower hose 19 to column body 15 and hand shower head 16 with rubber washers 20 18 Check valve 17 comes pre installed in hand shower Fig S FIG R FIG S NOTE Make sure that none of the hoses are bent or kinked after final installation Check water connections for proper flow make sure there are no leaks Do not forget to use the rubber washers to prevent leaks on the connections If you find that water pressure or volume is low clean the mesh gaskets 1 OPERATION To use the shower panel open your Noo N shower valve as per your normal use flip the diverter valve on the shower valve or on the tub spout to redirect water from the toe tester or tub s spout to the shower selector h head 6 switch Use selector switch shown tothe SNOWET Nea right to choose between the three single use options body jets 1 Shower head 2 The hand shower 3 The body jets You can also choose three more combined use options by placing the selector in between the icons this way you can use 4 The shower head and the hand shower COMBINED A 5 The hand shower and the body jets COMBINED B 6 The body jets and the shower head COMBINED C
5. ce rubber washer 9 into L fitting 8 Fig E 5 Connect L fitting 8 to shower arm 12 Fig F 6 Please check that the pre assembled rubber washer 13 has not become loose and is in shower head 14 as per Fig G 7 Screw shower head 14 on to shower arm 12 Fig H FIG A FIG B FIG C ORES A 2 FIG E Ye etter 8 With your shower valve CLOSED remove your existing shower arm from the wall using a wrench and turning it counter clockwise 9 As per Fig J put Teflon tape 23 on the shorter threaded end of the brass connector check valve end Check valve 2 comes pre installed in brass connector 3 Fig Install the brass connector 3 to wall protecting the treads with a rag if necessary to avoid damaging the threads using the mesh gasket 1 Make sure that the check valve end shorter thread goes towards the wall If the brass connector Is installed reversed there will be NO WATER FLOW 10 Clean the wall around the brass connector 3 thoroughly with a dry cloth Peel paper backing of the factory pre installed double sided tape 22 on the stainless steel mounting bracket 4 Fig K Place the stainless steel mounting bracket 4 on the brass connector 3 and adhere upright to the wall Fig L 11 Secure and tighten nut 5 on brass connector 3 Fig M FIG FIG J FIG K a 0 E o s fo Option A Double sided tape installation 12A1 Connect L fitting 7 to brass connector
6. hower head 1 1 YEAR HOME USE WARRANTY This unit is warranted to the original purchaser to be free of defects in material and workmanship for one 1 year from the date of purchase This warranty does not extend to commercial or institutional use or installation Quality Craft will repair or replace at its option the unit or its equipment in accordance with the following terms and conditions WARRANTY LIMITATIONS Our warranty does not cover defects damage or failure caused by the common carrier installer user or other person or resulting from without limitation any of the following careless handling lifting unit by plumbing abrading finish etc modification of any type for any reason including modification to meet local codes improper installation including installation not in accordance with instructions and specifications provided with the unit connections supplied by the installer of the equipment improper voltage supply or unauthorized electrical modification misuse incorrect operation or lack of proper routine maintenance operation of the unit without specified minimum amount of water or at inappropriate water temperature use of abrasive or improper cleaners or acts of God such as lightning floods earthquakes etc In addition Quality Craft WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause e g water damage to carpet ceiling loss of use e
7. ss connector Stainless steel mounting bracket Nut Restrictor L fitting L fitting Rubber washer 10 Top cover 11 Nut 12 Shower arm 13 Rubber washer 14 Shower head 15 Shower column 16 Hand shower head 17 Check valve 18 Rubber washer 19 Hose 20 Rubber washer 21 Wall anchors 22 Double sided tape 23 Teflon tape 24 Stainless steel cover 25 Bottom bracket 26 Stainless steel washers 2 7 Screws 28 Double sided tape INSTALLATION This unit is designed to be installed using your existing plumbing Your shower valve diverter valve or diverter tub spout will be used in its current position and will operate as it was used before with your current shower head existing _ existing _ amp shower valve shower valve G tub spout _ Hlverter diverter This unit can either be installed with Option A double sided tape or Option B bottom bracket and screws In both cases the weight of the unit is carried by the stainless steel mounting bracket The double sided tape and the bottom bracket avoid the possibility of the unit swinging during operation 1 Remove top cover 10 and stainless steel cover 24 from shower column 15 Fig A 2 Remove nut 11 from shower arm 12 Fig B 3 Secure shower arm 12 to shower column 15 using nut 11 Fig C amp D 4 Pla
8. tc including its own negligence damages to respecting or resulting from plated parts when chemicals are used in or on the unit optional equipment not manufactured by Quality Craft or defects that should have been discovered before installation This limited warranty does not include labor transportation or other costs incurred in the removal and or reinstallation of the original unit and or installation of a replacement unit any costs relating to obtaining access for repair or loss of use damage including loss of sales profit or business advantage of any kind under any circumstances lf you have a problem with your unit before installation please return to place of purchase If you have a problem with your unit during or after installation please call Quality Craft Customer Service at 1 800 459 4409 8 30am to 5 00pm EST or through our website at www qualitycraft com WARRANTY CLAIM PROCEDURE lf a claimable defect occurs please fill out a claim form through our website at www qualitycraft com or contact our customer service department at 1 800 459 4409 8 30am to 5 00pm EST Before you make your claim call please make sure you have 1 The description of the shower spa 2 Proof of sale 3 Details regarding the defect 4 Name and address of the owner and installer Claims must be filled out in writing and returned within six 6 months of appearance of defect Failure to comply with this stipulation will make the warran
9. ty null and void We reserve the right to a thirty day 30 delay following receipt of claim in which to inspect the product We assume no responsibility for labor costs or removing replacing a previously installed product or transportation or return of a product Made in China
Download Pdf Manuals
Related Search