6 - Honda Powersports
Contents
1. Z HONDA Accessory Application Publications No INSTALLATION DIGITAL METER KIT MUV700 TEET P N 08E80 HL1 100 INSTRUCTIONS Honda Dealer Please give a copy of these instructions to your customer PARTS LIST TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Box end wrench 10 mm Electric drill motor Drill bit 5 mm Marker Fretsaw Torque wrench July 2008 TORQUE CHART Tighten all screws bolts and nuts to their specified torque values Refer to the Service Manual for the torque values of the removed parts omen Se e INSTALLATION NOTE e Disconnect the negative cable from the battery before installing this accessory 1 Open the front hood as shown Digital meter 6 mm screw Collar Meter sub harness Meter cover 6 mm flange nut Clip 2008 American Honda Motor Co Inc All Rights Reserved 08E80 HL1 1000 91 1 o0f 10 2 Remove the steering wheel and the lever grips Refer to the Service Manual for specific removal instructions CENTER PAD STEERING WHEEL WASHER DRIVE SELECT LEVER GRIP CHANGE LEVER GRIP 3 Remove the left and right side net buckle as shown SIDE NET BUCKLE 2 of 10 08E80 HL1 1000 91 4 Remove the instrument panel Refer to the Service Manual for specific removal instructions Disconnect the vehicle s connector INSTRUMENT PANEL 2008 American Honda Motor Co In2. press the hourmeter odometer tripmeter select button and hold it in for at least 2 seconds TRIP nn UU mile LV ooostaie Hourmeter Odometer Tripmeter select button Tripmeter 10 of 10 08E80 HL1 1000 91 Hourmeter When selected the hourmeter shows accumulated hours while the ignition is ON The hourmeter provides accurate service period information for initial and regular maintenance To change the display from odometer or tripmeter to hourmeter press and release the hourmeter odometer tripmeter select button The hourmeter will appear Hourmeter mark Hourmeter Odometer Hourmeter Tripmeter select button 2008 American Honda Motor Co Inc All Rights Reserved
3. the meter cover over the digital meter Make sure it does not interfere with the recess or the odo trip button Mark the meter cover as shown below a MARKER RECESS METER COVER ODO TRIP BUTTON 5 of 10 16 Remove the case assembly 18 Install the meter cover as shown METER COVER 17 Drill at the marked point of the instrument panel as e Remove any burrs from the edge of the hole 5 INSTRUMENT PANEL SCREW Reuse ELECTRIC DRILL MOTOR 5 mm BIT 6 of 10 21 Reinstall the instrument panel Connect the meter sub harness to the vehicle s harness Reconnect all previously disconnected connectors Secure the vehicle s connector and meter sub harness VEHICLE S 10 PIN METER SUB CONNECTOR HARNESS CONNECTOR h XQ K LITIN ae K y Ke G Y nra SOM A bag HARNESS Install on the case assembly 22 Secure the harness with a clip CLIP Reuse Install on the case assembly SAL O T A 23 Reinstall the left and right side net buckles 24 Reinstall the steering wheel and lever grips 2008 American Honda Motor Co Inc All Rights Reserved 08E80 HL1 1000 91 Indicators amp Displays The indicators and displays on your vehicle keep you informed alert you to possible problems and make your ridin
4. c All Rights Reserved 5 Remove the case WIRE TIE Remove O J NG SCREW 6 Cut out the case as shown Remove any burrs from the edges of the hole FRETSAW Cut along the marked line 2008 American Honda Motor Co Inc All Rights Reserved 7 Connect the meter sub harness to the digital meter DIGITAL METER 10 PIN CONNECTOR METER SUB HARNESS CE LAG 21 PIN CONNECTOR 8 Pass the meter sub harness through the hole of the case DIGITAL METER AN MAAS SSX 08E80 HL1 1000 91 3 of 10 9 Assemble the digital meter as shown 6 mm FLANGE NUT COLLAR DIGITAL METER 6 mm SCREW 10 Remove the diff lock lens and harness as shown DIFF LOCK HARNESS 4 of 10 O8E80 HL1 1000 91 11 Cut out the instrument panel as shown Remove any burrs from the edges of the hole Cut out area To FRETSAW Cut out Inner side FRETSAW Cut along the marked line 2008 American Honda Motor Co Inc All Rights Reserved 12 Pass the diff lock harness through the hole in the instrument panel INSTRUMENT PANEL DIFF LOCK HARNESS Reuse 13 Install the diff lock lens as shown INSTRUMENT PANEL DIFF LOCK LENS Reuse 2008 American Honda Motor Co Inc All Rights Reserved 08E80 HL1 1000 91 14 Reinstall the case assembly SCREW Reuse 15 Position
5. elect button tripmeter or hourmeter Resets the tripmeter to zero 0 This button also used to reset the oil change indicator 8 of 10 08E80 HL1 1000 91 2008 American Honda Motor Co Inc All Rights Reserved Multi function Display The multi function display includes the following functions e Gear position indicator e Oil change indicator e Speedometer e Odometer e Tripmeter e Hourmeter Oil change indicator Gear Multi function position indicator GEAR POSITION N display NCA hy D7 ooo tRIP Odometer Tripmeter Hourmeter Gear Position Indicator The gear position indicator shows the gear position when the ignition switch is in the ON position The indicator displays N for neutral R for reverse and D for drive will be displayed on the gear position indicator when the transmission is not shifted into gear properly Before driving check that the gear position is displayed on the gear position indicator If the gear position indicator shows and blinks turn the ignition switch to the OFF position and then turn it back to the ON position again If the gear position indicator still shows and blinks see your Honda dealer Gear position indicator GEAR POSITION fad mile D7 ooostRip 2008 American Honda Motor Co Inc All Rights Reserved Oil change Indicator The oil indicator appears in the disp
6. g more enjoyable Refer to the indicators frequently Their functions are described on the following pages AWD indicator Neutral indicator High coolant temperature indicator Reverse indicator PGM FI indicator roo SS jH Multi function display D7 ovostrie Q hourmeter odometer tripmeter select button Lamp Check The High Coolant Temperature indicator and PGM FI indicator come on for a few seconds and then go off when you turn the ignition switch ON The indicators are identified in the table on page 8 with the words Lamp Check The Reverse indicator comes on and stays on when the transmission is in reverse The Neutral indicator comes on and stays on when the transmission is in neutral The 4WD indicator comes on and stays on when the drive mode lever is in the 4 wheel drive rear differential lock position If one of these indicators does not come on when it should have your Honda dealer check for problems 7 of 10 Display Check Reverse indicator Lights when the transmission is in When the ignition switch is turned ON the multi function reverse Lamp Check displ il il h Il th d d diaital Neutral indicator Lights when the transmission is in isplay will temporarily show all the modes and digita neutral Lamp Check segments so you can make sure the liquid crystal display 4WD indicator Lights when the drive mode is in the is functioning properly 4WD
7. lay when the mileage or operating hours on your vehicle approaches the oil change interval specified the maintenance schedule The oil change indicator comes on at 100 miles or 20 operating hours at the initial time and it comes on every 600 miles or 100 operating hours at the second or subsequent time Reset the indicator after each oil change To reset the indicator press and hold the hourmeter odometer tripmeter select button and turn the ignition switch to ON for more than 2 seconds The indicator will disappear If the oil is changed before the oil change indicator appears be sure to reset the oil change indicator after changing the oil The indicator will appears for 2 seconds then disappear This means the indicator is reset Oil change indicator A 2s IN ODO Hourmeter Odometer Tripmeter select button Odometer When selected the odometer registers total distance traveled in miles while the ignition is ON To change the display from tripmeter or hourmeter to odometer press and release the hourmeter odometer tripmeter select button Odometer Hourmeter Odometer Tripmeter select button 08E80 HL1 1000 91 9 of 10 Tripmeter When selected the tripmeter shows mileage per trip while the ignition is ON To change the display from odometer or hourmeter to tripmeter press and release the hourmeter odometer tripmeter select button To reset the tripmeter to zero
8. mode Lamp Check High coolant temperature Lights when coolant temperature is A PA 2 indicator high enough to adversely affect the The displays are identified in the table on page 8 with the hae service life of the engine words Display check If the high coolant temperature indicator comes on while you are If any part of these displays does not come on when it driving immediately bring the vehicle to a stop turn the engine off and let it should have your Honda dealer check for problems cool Lamp Check PGM FI indicator Lights when there is any abnormality in the PGM FI Programmed Fuel Multi function Injection system Should also light for display a few seconds and then go off when the ignition switch is turned ON If the indicator comes on at any other time reduce speed and take your vehicle to a Honda dealer as soon as possible Lamp Check Multi function display The display includes the following functions Display Check Gear position indicator Shows the gear position Oil change indicator Lights when specified maintenance interval for engine oil change is reached Speedometer Shows driven speed in miles per hour Odometer Shows the total miles driven Tripmeter Shows the number of miles driven since you last reset the meter Hourmeter Shows hours and tenths of hours of engine operation Hourmeter odometer Selects display of the odometer tripmeter s
Download Pdf Manuals
Related Search