SERVICE MANUAL MODEL SSW-322-F
Contents
1. ccccsccsssssesscsssssssrssesssesseees 70 TESTING suns sxssusaneseus onssasaecossnevinassescusovnusvenessesusontssensussousevcseontsepounseles 8 0 TROUBLESHOOTING 9 0 SPECTEICA TIONS sssssssacicescstcstcsssssunssciiesstnscsouceusetesanstcapocsechtonsberseaesesel 10 0 PARTS EIST cisiisesiisscavsevaanonnclasasnsavatonancdaatasctsacsenelanssccssustenndemeavsevasenuncs 11 0 ECC NOMIC 12 0 REPAIR AND RETURN 13 0 WARRANTY POLICY CEECO Communication Equipment and Engineering Company PROPRIETARY Issue 4 00 1 0 2 0 3 0 4 0 Issue 4 00 INTRODUCTION The practices in this manual provide installation and maintenance information for Model SSW 322 F which is a Stainless Steel Mini Wall Telephone The information in this manual is subject to change without notification For information not included in this manual please call or write CEECO Customer Service 519 W South Park Street Okeechobee FL 34972 863 357 0798 telephone 863 357 0006 facsimile info ceeco net www ceeco net GENERAL DESCRIPTION The CEECO model SSW 322 F is a Mini Wall Telephone equipped with a built in volume control button a flash button and a metal button keypad The telephone is designed for special applications where a telephone must be both sturdy2. and attractive OPERATION Lift the handset After dial tone is heard dial your number using the keypad Normal phone operation follows RECOMMENDED TOOLS AND TEST EQUIPMENT Volt Ohm Meter 1 4 Nut Driver Flat Blade Screw Driver Security Tool CEECO Part Number 301 037 CEECO 4 Communication Equipment and Engineering Company PROPRIETARY 5 0 Issue 4 00 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 5 1 5 2 5 3 5 4 5 5 5 6 5 7 5 8 5 9 Using a 301 037 security tool sold separately loosen and remove the security screw The security tool is for a standard 5 32 button head screw generally used on the framework of the phone booths Separate the cover assembly from the backplate assembly The backplate assembly may be installed on any standard backboard Run the inside station wire through the backplate assembly and terminate on the RJ11C modular jack on the backplate The use of a gas tube station protector is recommended The station ground should not exceed 50 ohms Plug the modular line cord from the cover assembly into the RJ11C terminal block Dress the line cable away from the security screw and install the cover assembly by inserting the tabs into the slots on top of the backplate Secure the cover assembly by tightening the security screw Never install telephone wiring during a lightning storm Never install telephone jacks in wet locations unless the jack is specifically desig
3. SSW 322 F XFD3 1 VC FL ISSUE4 0 SERVICE MANUAL FOR MODEL SSW 322 F MINI WALL TELEPHONE EQUIPPED WITH XFD3 1 PCB BUILT IN VOLUME CONTROL AND FLASH BUTTON CEECO Communication Equipment 519 W South Park Street amp Engineering Company Okeechobee FL 34972 Voice 863 357 0798 Fax 863 357 0006 Serving the Telephone Industry Since 1930 Issue 4 00 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue The following information is necessary when calling CEECO for assistance MODEL NUMBER MODEL SSW 322 F EQUIPPED WITH XFD3 1 PCB BUILT IN VOLUME CONTROL AND FLASH BUTTON SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you please have this information available when calling for technical support CEECO Communication Equipment amp Engineering Company 519 W South Park Street Okeechobee FL 34972 863 357 0798 telephone 863 357 0006 facsimile info ceeco net www ceeco net CEECO 2 Communication Equipment and Engineering Company PROPRIETARY TABLE OF CONTENTS SECTION 1 0 TINE RODUCTION 2 0 GENERAL DESCRIPTION ssssssscucsssvstsnsestavasensssscenatsostsnseessoustensscscosases 3 0 OPERATION 4 00 RECOMMENDED TOOLS AND TEST 5 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6 0 PROGRAMMING INSTRUCTION
4. Stainless Steel 5 Wide x 10 3 4 High x 5 1 2 deep Handset on hook Vertical surface mount 6 lbs BW 88T7 13717 TE T 6 5 8 Communication Equipment and Engineering Company PROPRIETARY 10 0 PARTS LIST QUANTITY PART NUMBER 1 321 020 1 705 110 1 1 1 301 004 29 1 401 009 1 301 581 1 301 588 2 301 570 1 301 018 1 321 015 1 321 016 1 308 015 1 301 052 1 301 054 ACCESSORIES 1 301 037 OPTIONS 301 106 29 or Issue 4 00 DESCRIPTION Stainless Steel Mini Housing Metal Button Keypad Printed Circuit Board Handset with Armored Cord Ringer Tongue and Bracket Assembly Hookswitch Cradle Microswitch Assembly Modular Cord Stainless Steel Backplate 1 4 20 x 3 4 Security Screw Swivel Grommet Modular Jack Security Tool Handset with Armored Cable 301 106 18 Prison with Internal Steel Lanyard CEECO 9 Communication Equipment and Engineering Company PROPRIETARY Issue 4 00 11 0 FCC NOTICE 11 1 11 3 FCC REGISTRATION AND REPAIR INFORMATION Your new telephone has been registered with the Federal Communication Commission FCC in accordance with Part 68 The FCC requires that you be advised of certain requirements involving the use of this telephone CONNECTION WITH THE NATIONWIDE TELEPHONE NETWORK The FCC requires that you connect this telephone to the Nationwide Telephone Network through a registered jack provided by the telephone company in your area T
5. TESTING 7 1 Connect the phone to a phone line a phone test set 7 2 Lift the handset dial tone is heard 73 Dial a number The transmitter is muted while the phone is dialing 74 Normal phone conversation is allowed Place the handset on hook 7 5 Place a call into the phone 7 6 Normal phone conversation is allowed CEECO 6 Communication Equipment and Engineering Company PROPRIETARY 8 0 Issue 4 00 TROUBLESHOOTING GUIDE Always visually check the phone for loose or shorted wires damaged terminals or damaged parts PROBLEM NO DIAL TONE POSSIBLE CAUSE LINE CORD RJ11C CONNECTOR HANDSET PC BOARD PROBLEM DIAL TONE IS DISTORTED POSSIBLE CAUSE HANDSET PC BOARD PROBLEM TRANSMITTER DOES NOT TURN ON POSSIBLE CAUSE HANDSET PC BOARD PROBLEM PHONE DOES NOT DIAL POSSIBLE CAUSE PC BOARD KEYPAD PROBLEM RINGER DOES NOT OPERATE POSSIBLE CAUSE RINGER PC BOARD CEECO 7 Communication Equipment and Engineering Company PROPRIETARY 9 0 SPECIFICATIONS INPUT POWER LOOP CURRENT IMPEDANCE SIGNALING HEARING AID COMPATIBLE ENVIRONMENTAL RINGER EQUIVALENCY TYPE JACK TELEPHONE COVER DIMENSIONS MOUNTING WEIGHT FCC REGISTRATION UL LISTED NO Issue 4 00 C O Line Powered 20ma min to 80ma max 600 ohms DTMF ROTARY 10PPS Meets standards Temperature 30 C to 85 C Humidity 20 90 non condensating 0 4A RJLIC Brushed 16 ga
6. his jack is a modular outlet which you can order from your local telephone company NOTIFICATION TO THE TELEPHONE COMPANY Before connecting this telephone the FCC requires that you notify your local telephone company business office The number is in the front of your phone book Tell them The line to which you will connect the telephone that is your phone number and the telephone s FCC registration number and ringer equivalence number These numbers are listed in section 7 00 The FCC further requires that you notify your local telephone company when permanently disconnecting this telephone CEECO 10 Communication Equipment and Engineering Company PROPRIETARY Issue 4 00 12 0 REPAIR AND RETURN INFORMATION 12 1 12 2 12 3 12 4 WARRANTY REPAIR Any device returned requiring warranty service repair or credit must be accompanied with a Return Material Authorization RMA Form It must include RMA Number return shipping instructions original purchase order number serial number and special marking instructions A tag with the trouble observed must be attached to the defective unit This information must be inside the shipping container DIRECT ALL INQUIRES TO CEECO Repair Department 863 357 0798 telephone 863 357 0006 facsimile info ceeco net www ceeco net NON WARRANTY REPAIR CEECO will repair equipment out of warranty for a set charge plus parts The customer must pay the shipping costs b
7. lty unit to CEECO for repair Modifications by any one other than CEECO will void the warranty CEECO 12 Communication Equipment and Engineering Company PROPRIETARY
8. ned for wet locations Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface Use caution when installing or modifying telephone lines CEECO 5 Communication Equipment and Engineering Company PROPRIETARY 6 0 Issue 4 00 PROGRAMMING INSTRUCTIONS 6 1 Connect this Telephone to the Telephone Line provided by your local Telephone Company or to analog type PABX Station 6 2 Using another Telephone Different Telephone Line equipped with a Touch Tone Keypad call this Telephone 6 3 When this Telephone rings 3 times or more answer this Telephone 6 4 Using the local or remote Keypad type followed by the five 5 digit pass code 7 0 Factory Default 23326 Two 2 beeps will be heard indicating a valid Pass Code entry Five 5 beeps will only be heard when errors occur PROGRAMMING FEATURES VIA KEYPAD e Clear Non Volatile Memory 97 e Enable Digit 55x x 0 9 Digit e PABX Disable 55 e Transmitter Muted Off Hook 560 Default e Transmitter Not Muted Off Hook 561 e Tone Dial Mode 570 Default e Rotary Dial Mode 571 Rotary 10pps e Pause After PABX Digit 58x x of Sec 1 9 max e No Transmitter Noise Reject 590 Normal Transmitter e Transmitter Noise Reject 591 Noise Reject Mode e Pause After PABX Toggle 67x x 0 Disable x 1 Enable e Change Pass Code 3 1x 5 Digits 0 9
9. oth directions RETURN FOR CREDIT Material may be returned for credit only with prior approval Material authorized for return is subject to a 20 restocking charge based on the manufacturer s list price Return Material Authorization must be requested no later than 30 days after original shipment Items returned for credit must be returned in their original shipping container CEECO 11 Communication Equipment and Engineering Company PROPRIETARY Issue 4 00 13 0 WARRANTY POLICY 13 1 GENERAL CEECO guarantees its products to be free from defects in material and workmanship for a period of 365 days from the date of original purchase CEECO s obligation under this warranty is limited to repair or replacement of any part found to be defective by CEECO UNDER NO CIRCUMSTANCES shall CEECO be liable for loss damage cost of repair or consequential damages of any kind which have been caused by neglect abuse or improper operation of equipment CEECO will repair or replace any unit during this period if found to be defective for reasons other than abuse and improper use or improper installation It is the buyer s responsibility to return the defective unit to the factory CEECO will then repair or replace any defective parts and return them to the buyer free of charge 13 2 PRINTED CIRCUIT BOARDS Printed circuit boards should not be repaired in the field If a unit is found to be faulty replace it with another unit and return the fau
Download Pdf Manuals
Related Search