VIO 300 S V 1.0.x VIO 200 S V 1.2.x
Contents
1. 22 170 IMPORTANT IMPORTANT 7 Confirm password with menu item SERVICE The unit switches to the Service level For the settings that can be changed there see table page 18 Once the keyword has been entered and provided the unit remains switched on the Service level can be called up direct i e without having to repeat keyword entry By switching off the unit the Ser vice level is protected by the keyword against unauthorized access again Change settings A setting change does not have to be confirmed The unit executes it immediately After restarting the unit the changed setting remains intact 1 Mark the setting that is to be changed using the selection but tons 2 Press the selection button next to the mark A new box opens In that box the setting can be changed with the nearest selection button Art Nr 801 16 284 02 08 Art Nr 801 16 284 02 08 6 Remedying malfunctions CHAPTER 6 Remedying malfunctions ATTENTION Safety information Adjustments technical tests modifications maintenance and repair work may only be performed by ERBE or persons trained by ERBE If the work is not performed by trained persons ERBE accepts no liability and warranty rights become void ERROR list Abbreviations of Error displays APC 2 Errors Control panel Errors CPU Sensors Errors IES 2 Errors Smoke evacuation system VEM 2 Errors Error display on the seven segment di2. 7 Maintenance and servicing 1 On the test specimen the dual surfaced neutral electrode lamp must light up red 2 Activate AUTO CUT via the footswitch The test specimen must inhibit activation and emit or display an optical and acoustic warning 2nd test step Testbox 20100 101 ey L_ 00000 L LH Pe z e The test specimen is connected to the power supply via the power cord e The test is performed without a load e The NE receptacle of the test specimen is connected to the VIO Testbox via the patient cable NE with the adapter cable e The dual pedal footswitch is connected Fig 7 13 1 On the test specimen the dual surfaced neutral electrode lamp must light up green 2 Activate AUTO CUT via the footswitch It must be possible to activate the test specimen without error or warning signals 3rd test step Testbox 20100 101 00000 00 00 ERBE vo Fig 7 14 66 70 Art Nr 80116 284 02 08 Art Nr 801 16 284 02 08 7 e Maintenance and servicing e The test specimen is connected to the power supply via the power cord e The test is performed without a load e The NE receptacle of the test specimen is connected to the VIO Testbox via the patient cable NE with the adapter cable e The dual pedal footswitch
3. Restart the unit If the error occurs again notify ERBE Service A E 85 86 Invalid resistance instru ment number Gas underdose e g hose blocked Check the accessories If the error persists notify ERBE Service Check the accessories If the error persists notify ERBE Service 25 170 6 Remedying malfunctions Recognizing module A APC 2 E Extension module VEM 2 Recog nizing module Error oe 90 Additional infor mation Description Low pressure at cylinder 1 Action Check the gas supply tank pressure regulator If the error persists notify ERBE Service 91 Low pressure at cylinder 2 Check the gas supply tank pressure regulator If the error persists notify ERBE Service AO Restart the unit If the error occurs again notify ERBE Service 26 70 Art Nr 801 16 284 02 08 Art Nr 80116 284 02 08 6 Remedying malfunctions B Errors Recognizing module Control panel Recog nizing module Error Additional infor code mation Description B 02 03 Restart the unit If the error occurs again notify ERBE Service B 05 as NESSY message NE is Check the NE accessories to 1 1 x not correctly applied and NE setting in setup Occurs if measurement of the NE contact resistance is outside the valid range on activation B OB as NESSY message
4. IMPORTANT IMPORTANT Who is allowed to perform servicing and main tenance work Adjustments tests modifications maintenance and repair work may only be performed by ERBE or persons trained by ERBE If the work is not performed by trained persons ERBE accepts no liability and warranty rights become void It is recommended that the safety check also be performed by ERBE or persons trained by ERBE What is a safety check The safety check is a preventive measure to examine whether the device is safe and ready for operation In order to perform the vari ous tests the current specifications and regulations of the particu lar country and the instructions in this service manual must be observed How often does a safety check have to be per formed ERBE recommends performing a safety check after every repair but at least once a year 43 170 7 Maintenance and servicing 44 170 WARNING ATTENTION ATTENTION IMPORTANT IMPORTANT IMPORTANT Safety check step by step For simplification the device to be tested is referred to below as the test specimen Safety information For safety reasons personnel protection the test specimen should generally be operated by a suitable isolating transformer An exceptional case is the tests for grounded conductor resis tance ground leakage current and patient leakage current in which the test specimen is supplied with current via the safety t
5. NE is Check the NE accessories from not correctly applied and NE setting in setup 1 2 x Occurs if measurement of the NE contact resistance is outside the valid range on activation B 10 Please terminate activa Check the accessories If tion Occurs if activation the error persists notify has been automatically ter ERBE Service minated e g by AutoStop and the activation signal remains longer than 5 s e g footswitch B 14 Restart the unit If the error occurs again notify ERBE Service B 17 Double activation Check the accessories If Occurs if two activation sig the error persists notify nals e g both pedals ofa ERBE Service footswitch are present simultaneously within 100 ms B 19 PowerFail Check the supply input Occurs if a PowerFail sig voltage nal is received but the Pow erFail does not actually happen within 2 s 27 170 6 Remedying malfunctions Recognizing module B Control panel RESI Error Additional infor nizing code mation Description Action module B 1c The maximum ON time Check the accessories If has been exceeded the error persists notify Occurs if activation lasts ERBE Service longer than the ON time selected in Setup B 1E Keyboard error Check the keyboard Occurs if a button pressed is recognized during initial ization B 1F NESSY symmetry monitor Check the NE accessories ing Occurs if an error is sig naled by t
6. cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE HF power meter Oscilloscope Probe 100 1 61 170 7 Maintenance and servicing 62 70 ENDO CUTIlandQ_ Test setup Oscilloscope BEE OOO ooo O O O High Voltage Differential probe HF power meter Fig 7 9 The test setup is designed as shown in the illustration above The test specimen is connected to the power supply via the power cord The levels of power are determined with the HF power meter The measuring cables are plugged into the HF power meter direct Test procedure 1 Set test specimen to EndoCut Effect 1 Cutting duration 1 Cutting interval 1 Set HF power meter to RL 1000 ohms Connect the probe of an oscilloscope to AE and NE Set oscilloscope to 200 V Div 20 ms Activate test specimen via the CUT button on the electrode han dle Determine the duration of the cutting pulse The tolerance range is 90 to 110 ms Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 7 e Maintenance and servicing NE monitoring of critical resistance for single surfaced neutral electrodes 1 Set test specimen to EndoCut Q Effect 1 Cutting duration 1 Cutting interval 2 2 Set HF power meter to RL 1000 ohms 3 Connect the probe of an oscilloscope to AE and NE 4 Set oscilloscope to 200 V D
7. cabs ceseedaadics ad e oriei 27 CAE Orsist ces ndtesiclicesselei cei A E a eladesestie cy eezeneitedene dy 33 DENO S igi scspiieigesatehacesseinicashdahtcespedad a a aeeie taanis 35 Er EO Soreni e einne operar rentan E a RERE ie 36 FEMO S no aa a ca sebeba sete dace dese EU EENET 37 PAE RSR T m 1O PEE AA T A A E EER 38 As NE EMMOFS nra tae e a a a aaie 40 Q EOFS pior ia a a EEE 41 5 170 TABLE OF CONTENTS 6 70 Maintenance and ServiCinn cccccssssesseeeereeeeseeeeeeeeees Who is allowed to perform servicing and maintenance work What is a safety CHECK s aeunira renade eiia ikera enk E REK How often does a safety check have to be performed Safety check step by Step cece eeeeeeeneeeeeeeeeeeeeeeseeeeeetaes Safety information ccccccceeceeeeeteeeeeeeeeeeteneeeeeeneeeeeees Testing and measuring equipment ee eeeteeeee eee eeeeee User manual and visual inspections ceeeeeeeeeeeeees Tests to be conducted in accordance with the national specifications and regulations 0 00 2 ee eeeeeeeeeeneeeeneeees DG reSiStanCe a iia di aae ede atte Performance tests anonn a i Footswitch Activation iss irii a Fingerswitch activation sssesssssesrrssrrrnrerirnnerrrnserrnnseren Automatic Start MOdEC ccc eeeeeeeeeeeeeeeeeeaeeeeeeeeeeeeaaa Automatic Stop MOdEC cccceeeeeeeeeneeeeeeeeeeeeeeneeeeeeeeeteeea Spark MOMMLOhsi acto ti eae alae eal HF powe
8. international 20190 045 Electrode handle ICC ACC 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE Safety tester with insulation testing gt 500 V DC Test setup WARNING Across the measuring lines there is the DC voltage of 500 V In order to avoid injuries only switch on the test specimen and safety tester when all the electrical connections have been made Fig 7 1 e The test specimen is connected to the power supply via the power cord e The NE receptacle of the test specimen is connected to the safety tester via the patient cable with NE with the adapter cord e The AE receptacle of the test specimen is connected to the safety tester via the patient cable with AE and electrode handle with the laboratory cable 47 170 7 Maintenance and servicing 48 170 Power switch Start routine acknowledgement tone Test procedure 1 2 3 4 5 Start safety tester in the Insulation resistance function The measured value displayed should be gt 200 MOhm Start test specimen and select the test progam TP relay In the test program TP relay use All to switch through all the output relays on the test specimen When doing so the mea sured value displayed on the safety tester must drop significantly from gt 200 MOhm Determine insulation resistance using the safety tester The measured val
9. notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 6 Remedying malfunctions Recognizing module A APC 2 E Extension module VEM 2 Recog nizing module A E Error code 21 23 Additional infor mation Description Action Restart the unit If the error occurs again notify ERBE Service 30 Restart the unit If the error occurs again notify ERBE Service A E 38 Type detection of receptacle 1 fails to agree with the stored value Check and save the recep tacle configuration in the Version List test program If the error occurs again notify ERBE Service A E 39 Type detection of receptacle 2 fails to agree with the stored value Check and save the recep tacle configuration in the Version List test program If the error occurs again notify ERBE Service 40 Flow specification not attained Check the accessories If the error persists notify ERBE Service 41 Flow specification exceeded Restart the unit If the error occurs again notify ERBE Service A E A E A E 7D 7E 7F 80 Operating system error Internal state incorrect Restart the unit If the error occurs again notify ERBE Service Information no fault condi tion Information no fault condi tion A E 81 83 Protocol violation CAN
10. vation at the latest an optical warning must be emitted and within another 2 seconds an acoustic warning must be emitted The test specimen must interrupt activation 69 70 7 Maintenance and servicing 70 70 Art Nr 801 16 284 02 08
11. 4 Adapter cable bipolar z HF power meter 20189 100 Dual pedal footswitch Art Nr 80116 284 02 08 7 Maintenance and servicing Art Nr 801 16 284 02 08 BIPOLAR SOFT COAG Test setup vio Bipolar HF power meter Fig 7 7 e The test specimen is connected to the power supply via the power cord e The levels of power are determined with the HF power meter The measuring cables are plugged into the HF power meter direct e The dual pedal footswitch is connected Test procedure 1 Set test specimen to BIPOLAR SOFT Effect 8 120 watts 2 Set HF power meter to RL 75 ohms 3 Activate test specimen via COAG pedal on the footswitch 4 Determine and document measured value The tolerance range is 96 to 144 watts 59 170 7 Maintenance and servicing SOFT COAG Test setup FORCED COAG SPRAY COAG depending on 60 170 the unit variant HF power meter Fig 7 8 The test specimen is connected to the power supply via the power cord The levels of power are determined with the HF power meter The measuring cables are plugged into the HF power meter direct Test procedure VIO 200 S 1 w Set test specimen to SOFT COAG Effect 8 120 watts Set HF power meter to RL 50 ohms Activate test specimen vi
12. Information no fault condi Occurs if a module is rec tion ognized B EB Receptacle was recog Check and save the recep nized tacle configuration in the Occurs if a receptacle is Version List test program recognized If the error occurs again notify ERBE Service 32 70 Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 6 Remedying malfunctions C Errors Recognizing module C CPU Sensors Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service C 01 C 04 06 C oD C 21 C 26 C 30 38 C 41 48 C 51 58 C 5A 5B C 61 64 C 70 72 C 75 Restart the unit If the error occurs again notify ERBE Service 33 70 6 Remedying malfunction
13. VIO 300 S V 1 0 x V 1 1 x V 1 2 x VIO 200 S v 1 2 x 02 08 SERVICE MANUAL VIO 300 S VIO 200 S Service Manual Art No 80116 284 All rights to this manual in particular rights of duplication dissemination and translation are reserved No part of this manual may be reproduced in any form by photocopying microfilming or other methods or processed du plicated or disseminated by the use of electronic systems without the written consent of ERBE Elektromedizin Gm bH The information contained in this manual may be amended or supplemented without prior notice and represents no obligation on the part of ERBE Elektromedizin GmbH Printed by ERBE Elektromedizin Printed in Germany Copyright ERBE Elektromedizin GmbH Tubingen 2008 Art Nr 801 16 284 02 08 TABLE OF CONTENTS Table of Contents Chapter Title Page Safety UFO ation oni seisss cosicececcescne ce sencece eecethe aa iaaa ack nedteentieedee 7 Classification of the safety information cccceseeeeeeseeeeeneeeeeeeeeseneeetsnees 7 Knowledge of the User Manual ecceeceeccceeeeeenceeeeeesneeeeeeesneeeeeseneeeeeeeaa 7 Protection from the risk of electric SHOCK 0 0 0 eee eeeneeeeeeeeneeeeeseetaeeeeeeeaaees 7 Electrostatically sensitive COMPONENTS cceeeeeeeeeeeeteeeeeeeeeteeeeeteneeeeeteee 8 Liability and warranty cccecceeeeeeeeneeeeeeeeneeeeeeeteaeeeeeeetaeeeeeeeaeeeeetenaeeeeeneal 8 Modifications sas sisccetecs onsen du
14. a COAG button on the electrode handle Determine and document measured value The tolerance range is 96 to 144 watts Set test specimen to FORCED COAG Effect 4 120 watts Set HF power meter to RL 500 ohms Activate test specimen via COAG button on the electrode handle Determine and document measured value The tolerance range is 96 to 144 watts Test procedure VIO 300 S 1 Set test specimen to SOFT COAG Effect 8 200 watts Set HF power meter to RL 50 ohms Activate test specimen via COAG button on the electrode handle Determine and document measured value The tolerance range is 160 to 240 watts Art Nr 80116 284 02 08 Art Nr 801 16 284 02 08 7 e Maintenance and servicing 9 Set test specimen to FORCED COAG Effect 4 120 watts Set HF power meter to RL 500 ohms Activate test specimen via COAG button on the electrode handle Determine and document measured value The tolerance range is 96 to 144 watts Set test specimen to SPRAY COAG Effect 2 120 watts Set HF power meter to RL 500 ohms Activate test specimen via COAG button on the electrode handle Determine and document measured value The tolerance range is 96 to 144 watts Performance test upgrades Testing and measuring equipment ERBE Art No Description 20192 127 Patient cable AE or 20192 110 Patient cable AE international 20190 045 Electrode handle ICC ACC 20194 070 Patient
15. asuring equipment IMPORTANT The following list contains the testing and measuring equipment recommended by ERBE for servicing Where ERBE article num bers are specified only original ERBE testing and measuring equipment should be used ERBE Description Art No P Safety tester with insulation testing gt 500 V DC HF power meter recommended Metron QA ES Oscilloscope 100 MHz or higher recommended Tektronix TDS 1012 High Voltage Differential Probe recommended TESTTEC TT SI 9010 Tektronix P5210 or Sapphire SI 9010 20188 100 Single pedal footswitch 20189 100 Dual pedal footswitch 20190 045 Electrode handle ICC ACC 20192 127 Patient cable AE 20192 110 Patient cable AE international 20196 045 Bipolar cable 20196 053 Bipolar cable international 20100 034 Adapter cable bipolar 20194 070 Patient cable NE 20194 075 Patient cable NE international 20100 033 Adapter cable NE 20100 035 Cable LF leakage current 20100 038 Cable LF leakage current international 20100 101 VIO Testbox Symmetry Resistance NE asymmetry critical resistance 20100 102 VIO Testbox Auto Start Auto Stop bipolar start stop 20100 019 Testbox spark monitor 230 V 45 170 7 Maintenance and servicing Grounded conductor test Ground leakage current 46 170 measurement Patient leakage current measurement User manual and visual inspections Test specimen and accessori
16. bol For safety reasons multiple outlets and extension cords should not be used If their use is unavoidable they also must be provided with proper grounding WARNING Unplug the power cord from the outlet before exchanging parts of the unit or cleaning it WARNING Do not plug a wet power cord into the unit or into an outlet WARNING Do not touch any unprotected wires or conductive surfaces while the unit is opened and under voltage 7 170 1 Safety information 8 170 WARNING CAUTION ATTENTION ATTENTION Blown line fuses may only be replaced by a competent technician Only replacement fuses of the rating specified on the unit s name plate may be used Before resuming operation the unit must be subjected to a performance test by a competent technician Electrostatically sensitive components This unit contains electrostatically sensitive components Work at an anti static workplace while repairing the unit Wear a grounding armband while working with electrostatically sensitive compo nents Hold the circuit boards by their non conducting corners Use an anti static container for transporting electrostatically sensi tive components and the circuit boards Liability and warranty Adjustments tests modifications maintenance and repair work may only be performed by ERBE or persons trained by ERBE If the work is not performed by trained persons ERBE accepts no liability and warranty rights bec
17. brief signal tones Spark monitor Testing and measuring equipment ERBE Description Art No 20192 127 Patient cable AE or 20192 110 Patient cable AE international 20190 045 Electrode handle ICC ACC 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE 20100 019 Testbox spark monitor 230 V Test setup Testbox 20100 019 Fig 7 4 Art Nr 80116 284 02 08 7 e Maintenance and servicing Art Nr 80116 284 02 08 e The test specimen is connected to the power supply via the power cord e The test specimen is connected to the testbox Test procedure Call up Test program mode 1 Call up service level see page 20 2 Select the Test programs setting and press the adjacent button to call it up The test specimen switches to the test program mode 3 Select the TP generator test program and press the adjacent button to call it up TP generator Test mode Test mode AUTO FORCED SPRAY supply voltage Output receptacle 2 MONOPOLAR 4 Select the receptacle on which to measure in the test program under Output receptacle select here 2 receptacle slot MONOPOLAR arrangement with monopolar receptacle Measurement 1 On the Testbox press button S1 2 In the test program read off the measured value for Spark The tolerance range is 245 t
18. by the service technician after every software update and after every unit upgrade and conversion For this purpose compare the receptacle configurations indicated on the Version list with the physical configurations on the unit If the two agree save the receptacle configurations with Safe config 2 depending on the unit variant 19 70 5 e Setup and Service settings Call up Setup level Call up Service level 20 70 Call up Setup and Service settings Pros 0 BASIC PROG xi Set zan og 4 up BIPOLAR Y ES BIPOLAR BIPOLAR CUT SOFT a 1 Call up CUT COAG box and select menu item Prog Setup lt gt Save program 2 Select menu item Setup The unit switches to the Setup level For the settings that can be changed there see table page 17 Q Pros 0 BASIC PROG mxi BIPOLAR BIPOLAR i CUT SOFT _ i 1 Call up CUT COAG box and select menu item Prog Setup gt Return gt Select program gt o cave program 2 Select menu item Service The unit switches to the Password input box Art Nr 801 16 284 02 08 Art Nr 801 16 284 02 08 5 e Setup and Service settings 3 Inthe menu item Case select upper case 4 Enter password VIOS When doing so use the Up and Down keys to set the initial letter 5 Confirm the correct letter with the selection button 6 Repeat steps 3 to 5 letter by letter 21 170 5 e Setup and Service settings
19. controls of the unit s The relevant User Manual for the unit s knowledge of which is assumed for servicing work provides detailed information about how to use the unit s 8 Effect 8 Q amp max Watts o oa i 2 3 4 9 10 11 14 15 16 17 12 170 Fig 3 1 Power Switch buttons CUT LED Selection buttons COAG LED Focus buttons Pilot lamps for neutral electrodes Pilot lamps for footswitches Pilot lamp for AUTO START BIPOLAR MONOPOLAR MONOPOLAR NEUTRAL Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 3 Unit description IMPORTANT Controls at the rear This unit comes with different power supply modules plug in or screw in VIO S with screw in power supply module Fig 3 2 gt O N Footswitch sockets ECB socket ERBE Communication Bus Potential equalization terminal Power supply module with fuses 13 70 3 Unit description VIO S with plug in power supply module p OY BR fei f EB P Fig 3 3 1 Footswitch sockets 2 ECB socket ERBE Communication Bus 3 Potential equalization terminal 4 Power supply module with fuses 14 70 Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 4 e Technical Data CHAPTER 4 Technical Data Powe
20. ctivation time there must be no warning signal ERBE yo S606 O Testbox 20100 101 Fig 7 16 The test specimen is connected to the power supply via the power cord The NE receptacle of the test specimen is connected to the VIO Testbox via the patient cable NE with the adapter cable The AE receptacle of the test specimen is connected to the VIO Testbox AE receptacle via the patient cable AE and the elec trode handle with the laboratory cable Art Nr 80116 284 02 08 7 e Maintenance and servicing Art Nr 801 16 284 02 08 1 Activate test specimen via COAG button on the electrode handle for approx 10 seconds There must be an optical warning signal 2 seconds after activation at the latest The test specimen must not interrupt activation 3rd test step S566 0 Testbox 20100 101 Fig 7 17 e The test specimen is connected to the power supply via the power cord e The NE receptacle of the test specimen is connected to the VIO Testbox via the patient cable NE with the adapter cable e The AE receptacle of the test specimen is connected to the VIO Testbox AE receptacle via the patient cable AE and the elec trode handle with the laboratory cable 1 Activate the test specimen with the COAG button on the elec trode handle for approx 10 seconds Within 2 seconds after acti
21. d The test is performed without a load The NE receptacle of the test specimen is connected to the VIO Testbox via the patient cable NE with the adapter cable The dual pedal footswitch is connected Art Nr 80116 284 02 08 7 Maintenance and servicing Art Nr 801 16 284 02 08 1 On the test specimen the single surfaced neutral electrode lamp must light up green 2 Activate AUTO CUT via the footswitch It must be possible to activate the test specimen without error or warning signals NE monitoring of critical Testing and measuring equipment resistance for dual surfaced a Description neutral electrodes a 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE 20100 101 VIO Testbox Symmetry Resistance NE asymmetry critical resistance 20189 100 Dual pedal footswitch Presets on the test specimen e AUTO CUT Effect 1 10 watts e Neutral electrode dual surface Test set up and test procedure 1st test step Testbox 20100 101 T i lt Fig 7 12 e The test specimen is connected to the power supply via the power cord e The test is performed without a load e The NE receptacle of the test specimen is connected to the VIO Testbox via the patient cable NE with the adapter cable e The dual pedal footswitch is connected 65 170
22. d value The tolerance range is 240 to 360 watts o 1 Set test specimen to DRY CUT Effect 8 200 watts 2 Set HF power meter to RL 500 ohms 3 Activate test specimen via CUT button on the electrode handle 4 Determine and document measured value The tolerance range is 160 to 240 watts BIPOLAR CUT Test setup depending on the unit variant i Bipolar HF power meter Fig 7 6 e The test specimen is connected to the power supply via the power cord e The levels of power are determined with the HF power meter The measuring cables are plugged into the HF power meter direct e The dual pedal footswitch is connected 57 170 7 Maintenance and servicing Test procedure 1 Set test specimen to BIPOLAR CUT Effect 8 100 watts 2 Set HF power meter to RL 500 ohms 3 Activate test specimen via CUT pedal on the footswitch 4 Determine and document measured value The tolerance range is 80 to 120 watts HF power output COAGULATE Testing and measuring equipment 58 170 PRBE Description Art No 20192 127 Patient cable AE or 20192 110 Patient cable AE international 20190 045 Electrode handle ICC ACC 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE 20196 045 Bipolar cable or 20196 053 Bipolar cable international 20100 03
23. display on the seven segment displays Display Description Action ErrdlS Restart the unit If the error occurs again notify ERBE Service ErrtAS Restart the unit If the error occurs again notify ERBE Service 36 70 Art Nr 801 16 284 02 08 Art Nr 80116 284 02 08 6 Remedying malfunctions F Errors Recognizing module F Footswitch Recog es nizing Error Additional infor Description code mation module F 01 CRC error Occurs if an Replace the ECBS foot error is detected during switch CRC monitoring of the foot switch at start up e g bit failure in the Flash memory or error when downloading software 37 170 6 e Remedying malfunctions 2 3 5 6 Errors Recognizing module 2 3 5 6 IIF Instrument Interface of corresponding receptacle slot Recog nizing module Error code Additional infor mation Description Action 2 3 5 6 01 07 Restart the unit If the error Buchse occurs again notify ERBE Service 2 3 5 6 08 Overcurrent activation rec Check the accessories If Buchse ognition the error persists notify The measurement current ERBE Service for analysis of the activation recognition is too high 2 3 5 6 09 Restart the unit If the error Buchse occurs again notify ERBE Service 2 3 5 6 OA Overcurrent instrument rec Check the accessories If Buchse ognition the error persists no
24. e unit and switch attempts to log with notify ERBE Service an invalid version B 60 Error in the version check Remove the module con Occurs if an IES footswitch cerned from the unit and attempts to log with an notify ERBE Service invalid version B 81 Restart the unit If the error occurs again notify ERBE Service B 84 Footswitch was recog Information no fault condi nized by the system tion Occurs if a footswitch is connected B 85 Footswitch was discon Information no fault condi nected from the system tion Occurs if a footswitch is disconnected from the sys tem B 87 Restart the unit If the error occurs again notify ERBE Service B 8B Restart the unit If the error occurs again notify ERBE Service B 8D No status message from Check connectors Check APC module APC Occurs if an APC module is disconnected from the system B 8E 8F Restart the unit If the error occurs again notify ERBE Service B 90 Restart the unit If the error occurs again notify ERBE Service 29 70 6 Remedying malfunctions Recognizing module B Control panel Reco9 Error Additional infor cea nizing Description Action code mation module B 91 No status message from Check connectors Check IES module IES 2 Occurs if the IES module is disconnected from the sys tem B 95 New instrument recognized Information no fault condi by system tion Occu
25. ent recognition R Check the accessories If Buchse window violated The resis the error persists notify tor value determined for the ERBE Service instrument recognition can not be reliably assigned to a setpoint 2 3 5 6 85 Short circuit activation rec Check the accessories If Buchse ognition R_ALT The resis the error persists notify tor value determined for the ERBE Service activation recognition corre sponds to a short circuit 2 3 5 6 86 Activation error Activation Check the accessories If Buchse not consistent with instru the error persists notify ment type ERBE Service 2 3 5 6 87 89 Restart the unit If the error Buchse occurs again notify ERBE Service 2 3 5 6 8A 8F Restart the unit If the error Buchse occurs again notify ERBE Service 2 3 5 6 90 Restart the unit If the error Buchse occurs again notify ERBE Service 39 170 6 e Remedying malfunctions 4 NE Errors Recognizing module 4 NE Nessy2 Recog nizing module 4 NE Error Additional infor code mation Description 01 08 Restart the unit If the error occurs again notify ERBE Service 4 NE OC OE Restart the unit If the error occurs again notify ERBE Service 4 NE 40 70 10 11 Restart the unit If the error occurs again notify ERBE Service Art Nr 801 16 284 02 08 Art Nr 80116 284 02 08 6 Remedy
26. ently of DRY CUT depending on the unit variant 10 70 Art Nr 80116 284 02 08 Art Nr 801 16 284 02 08 3 Unit description CHAPTER 3 Unit description How do the unit variants dif fer from one another How do I determine the unit variant Which service work does the unit variant affect Unit variants There are VIO S units in different unit variants Each unit variant has modes assigned permanently to it In the VIO 300 S the unit variant 1 basic variant contains all modes approved for this unit These modes are described in the User Man ual of the unit All other units contain less modes than the basic vari ant A list of all unit variants for the VIO 300 S can be requested from ERBE Tubingen Currently only unit variant 1 is available in the VIO 200 S The modes of this variant are described in the User Manual of the unit When the VIO S is switched on the following information about the unit software appears on the start screen e Software status e g 1 2 x e Upgrades e g EndoCut I e Unit variant e g Variation 2 The VIO 200 S is an exception Since at the time of printing only unit variant 1 is available no statement about the unit variant is made on the start screen The unit variant has an effect on the adjustment and some tests of the safety check 11 70 3 Unit description IMPORTANT Controls at the front This chapter contains an overview of the
27. erminate activation Art Nr 80116 284 02 08 7 Maintenance and servicing Art Nr 801 16 284 02 08 2nd test step 1 Set test specimen to BIPOLAR SOFT Effect 8 50 W AUTO START 2 On the VIO Testbox press button T1 The test specimen must start activation after the set start delay 3 Press button T2 The test specimen must terminate activation Automatic stop mode Testing and measuring equipment PRBE Description Art No 20196 045 Bipolar cable or 20196 053 Bipolar cable international 20100 034 Adapter cable bipolar 20100 102 VIO Testbox Auto Start Auto Stop bipolar start stop 20188 100 Single pedal footswitch Test setup Testbox 20100 102 Fig 7 3 e The test specimen is connected to the power supply via the power cord e The Bipolar receptacle of the test specimen is connected to the VIO Testbox via the bipolar cable with the adapter cable e The single pedal footswitch is connected 53 170 7 Maintenance and servicing 54 170 Test procedure 1 Set test specimen to BIPOLAR SOFT with AutoStop Effect 4 50 watts 2 On the VIO Testbox hold down button T3 3 Activate BIROLAR SOFT with the footswitch keeping the pedal pressed 4 Hold down button T3 for approx 5 s then let go Within another 9 s at the latest the test specimen must terminate activation and emit two
28. es where enclosed undamaged externally User manual present All labels on the test specimen conformity declaration mark rat ing plate and all wording present and readily legible Tests to be conducted in accordance with the national specifications and regulations Ground terminal to chassis Ground terminal to potential equalization pin Ground leakage current normal condition N C Ground leakage current single fault condition S F C Patient leakage current normal condition N C Patient leakage current single fault condition S F C IMPORTANT Close the output relay of the unit in the TP relay test program for testing the patient leakage current On the test specimen 1 2 5 6 Call up service level see page 20 Select the Test programs setting and press the adjacent button to call it up The test specimen switches to the test program mode Select the TP relay test program and press the adjacent button to call it up 0001 Return 0000 0000 Return OR ET 0000 0000 ORTAR Eee Close all relays in the test program via All Relays closed Relays open Perform the measurement Switch the test specimen off Art Nr 80116 284 02 08 7 Maintenance and servicing Art Nr 801 16 284 02 08 DC resistance Testing and measuring equipment ERBE Description Art No 20192 127 Patient cable AE or 20192 110 Patient cable AE
29. ester In the event of a fault occurring in the test specimen or individual components during the safety check the test steps taken so far no longer apply Remedy the defect and repeat the safety check from the beginning The specifications made in this chapter for test programs test program settings allow the service technician to perform the safety check In addition the test program mode provides a number of diagnostic and inspection options for the service technician They are described in the repair manual ERBE Elektromedizin expressly states that the full functional range of the test program mode may not be used without precise knowledge of the individual test programs It is assumed that the user knows how to operate the test speci men the test equipment the measuring equipment and auxiliary test equipment The test instructions only apply in conjunction with the relevant test steps Test equipment measuring equipment and auxiliary test equip ment cables test boxes etc are listed separately at the begin ning of each test unit Where ERBE article numbers are specified only original ERBE test equipment measuring equipment and auxiliary test equipment may be used The test report for the safety check can be requested from ERBE Technical Service Tubingen For the address see address sheet on last page Art Nr 801 16 284 02 08 Art Nr 801 16 284 02 08 7 e Maintenance and servicing Testing and me
30. gnals a value between 20 and 50 B B1 NESSY current density Check the NE accessories warning Occurs if the Nessy current density monitoring signals a value above the limit curve B C4 Purge function not Information no fault condi assigned tion Occurs if the purge button on the APC is pressed and no APC receptacle was selected B C5 Purge function not Information no fault condi assigned tion Occurs if the Purge button on the APC is pressed an no instrument is con nected B D2 No status message from Information no fault condi VEM module tion Occurs if the VEM module is disconnected from the system B D3 No status message from Information no fault condi EIP module tion Occurs if the EIP module is disconnected from the sys tem B D4 D6 Restart the unit If the error occurs again notify ERBE Service B DA Occurs if a module Remove the module con responds that is not sup cerned from the unit and ported by the system notify ERBE Service B DB Occurs if a button that is Remove the module con not selectable is pressed after a timeout cerned from the unit and notify ERBE Service 31 170 6 Remedying malfunctions Recognizing module B Control panel Recog nizing module Error Additional infor oe mation Description Action B DC Restart the unit If the error occurs again notify ERBE Service B EA Module was recognized
31. h the AE patient cable to the 1st Activation CUT COAG Monopolar receptacle on the test specimen 2 Press CUT button on the electrode handle On the test specimen CUT must be activated 3 Press COAG button on the electrode handle On the test speci men COAG must be activated 4 Connect the electrode handle with the AE patient cable to the 2nd Monopolar receptacle if present on the test specimen 5 Repeat test steps 2 and 3 51 170 7 Maintenance and servicing 52 170 1st test step Automatic start mode Testing and measuring equipment ERBE Description Art No 20196 045 Bipolar cable or 20196 053 Bipolar cable international 20100 034 Adapter cable bipolar 20100 102 VIO Testbox Auto Start Auto Stop bipolar start stop Test setup Testbox 20100 102 Fig 7 2 e The test specimen is connected to the power supply via the power cord e The Bipolar receptacle of the test specimen is connected to the VIO Testbox via the bipolar cable with the adapter cable Test procedure 1 Inthe Setup of the test specimen establish the set start delay for the AUTO START setting Make a note of the value 2 Set test specimen to BIPOLAR SOFT Effect 1 50 W AUTO START 3 On the VIO Testbox press button T1 The test specimen must start activation after the set start delay 4 Press button T2 The test specimen must t
32. he Nessy sym metry monitoring during activation B 2A 2C Restart the unit If the error occurs again notify ERBE Service B 50 59 Restart the unit If the error occurs again notify ERBE Service B 5A Error in the version check Remove the module con Occurs if the VEM module cerned from the unit and attempts to log with an notify ERBE Service invalid version B 5B Error in the version check Remove the module con Occurs if the IES module cerned from the unit and attempts to log with an notify ERBE Service invalid version B 5C Error in the version check Remove the module con Occurs if the EIP module cerned from the unit and attempts to log with an notify ERBE Service invalid version B 5D Error in the version check Remove the module con Occurs if a dual pedal foot cerned from the unit and switch attempts to log with notify ERBE Service an invalid version B 5E Error in the version check Remove the module con Occurs if a single pedal cerned from the unit and footswitch attempts to log notify ERBE Service with an invalid version 28 170 Art Nr 801 16 284 02 08 Art Nr 80116 284 02 08 6 Remedying malfunctions Recognizing module B Control panel Recog nizing module Error code Additional infor mation Description Action B 5F Error in the version check Remove the module con Occurs if a ReMode foot cerned from th
33. ing malfunctions 9 Errors Recognizing module 9 ERBE Irrigation Pump EIP 2 Recog nizing module Error code Additional infor mation Description 9 80 CRC Error Restart the unit If the error occurs again notify ERBE Service 9 82 Pump lid openat User error Close the pump lid before ON The pump lid of the EIP 2is activation or do not open it not closed at the start of during activation activation or is opened dur ing activation Unit error Restart the unit If the error occurs again notify ERBE Service 9 84 Time Out Error User error End the activation Itis then Activation of the EIP 2 was possible to active the EIP 2 maintained for more than new If the error occurs 20 seconds Maximum acti again check the accesso vation time for the EIP 2 is ries 20 seconds 9 88 UeWS Error Restart the unit If the error occurs again notify ERBE Service 9 90 No current or no Restart the unit If the error load occurs again notify ERBE Service 9 AO Current too high Restart the unit If the error at ON occurs again notify ERBE Service 9 Co Motor control Restart the unit If the error faulty voltage too occurs again notify ERBE high at ON Service 41 170 6 e Remedying malfunctions 42 170 Art Nr 801 16 284 02 08 Art Nr 801 16 284 02 08 7 e Maintenance and servicing CHAPTER 7 Maintenance and servicing ATTENTION
34. is connected 1 On the test specimen the dual surfaced neutral electrode lamp must light up red 2 Activate AUTO CUT via the footswitch The test specimen must inhibit activation and emit or display an optical and acoustic warning NE monitoring of asymmetry Testing and measuring equipment abe Description Art No 20192 127 Patient cable AE or 20192 110 Patient cable AE international 20190 045 Electrode handle ICC ACC 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE 20100 101 VIO Testbox Symmetry Resistance NE asymmetry critical resistance Presets on the test specimen e SOFT COAG Effect 1 10 watts e Neutral electrode dual surface 67 170 7 Maintenance and servicing 68 170 1st test step 2nd test step Test set up and test procedure yo NE 0 00 O Testbox 20100 101 Fig 7 15 1 The test specimen is connected to the power supply via the power cord The NE receptacle of the test specimen is connected to the VIO Testbox via the patient cable NE with the adapter cable The AE receptacle of the test specimen is connected to the VIO Testbox AE receptacle via the patient cable AE and the elec trode handle with the laboratory cable Activate test specimen via COAG button on the electrode handle for approx 10 seconds During the entire a
35. iv 100 ms 5 Activate test specimen via the CUT button on the electrode han dle 6 Determine the duration of the cutting pulse The tolerance range is 320 to 380 ms Monitor circuits Testing and measuring equipment ERBE Art No Description 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE 20100 101 VIO Testbox Symmetry Resistance NE asymmetry critical resistance 20189 100 Dual pedal footswitch Presets on the test specimen e AUTO CUT Effect 1 10 watts e Neutral electrode single surface 63 70 7 Maintenance and servicing 64 170 1st test step 2nd test step Test set up and test procedure Testbox 20100 101 Fig 7 10 The test specimen is connected to the power supply via the power cord The test is performed without a load The NE receptacle of the test specimen is connected to the VIO Testbox via the patient cable NE with the adapter cable The dual pedal footswitch is connected On the test specimen the single surfaced neutral electrode lamp must light up red Activate AUTO CUT via the footswitch The test specimen must inhibit activation and emit or display an optical and acoustic warning Testbox 20100 101 Zz Fig 7 11 The test specimen is connected to the power supply via the power cor
36. lable from Description Contrast V 1 0 x Setting display contrast System volume V 1 0 x Setting the volume of activation tones The activation tones must be easy to hear Key volume V 1 0 x Setting key volume AUTO START V 1 0 x Input of start delay for the AUTO START function Brightness LED V 1 0 x Setting the brightness of the LEDs es Dis V 1 0 x Setting display brightness play 17 1 70 5 e Setup and Service settings Overview of Service settings Only accessible to service personnel Setting Available from Description Date V 1 0 x Self explanatory Time V 1 0 x Self explanatory Neutral electrode V 1 0 x Single surface Dual surface Either way Dynamic Factory setting up to V 1 1 x Either way Factory setting as from V 1 2 x Dynamic Time limit V 1 0 x Setting the time after which activation terminates automati cally Automatic time V 1 0 x Setting the time for which an input box is shown on the dis play Error list V 1 0 x Saves all the errors that are detected and reported Version list V 1 0 x Indicates the software versions of all the connected compo nents Safe config option APC parameter V 1 0 x Setting the following parameters APC supply self explanatory APC Auto Purge the instrument is automatically purged with gas when itis plugged into the APC receptacle or if the instrument is plugged into the APC receptacle already it is automatically purged with gas when the unit s
37. niasen see evateeadessucutsieneedvancuvenscavvansbusectaet 9 UN it GOSCrIPUON GS vcsvcsccscesceccceessssisesseaviessacssnactassssasseesesessnssenssascenecs 11 Uniti variants an aaa aaa aaa aa a aaa a asthe AE aa ee aata 11 Controls at the front eeessseseseeeeesiresrreskrtsttrstnrserinssrnnertnsernssnnsetnnnrnn nennt 12 Controls attherear isna a iach teeth oli ia aiae ai aa a ea aaia 13 T chni al D t siii nasapian icoane aina ranana as aane aindar aias aatis Saas 15 Setup and Service settings ccccceeeceeeseeeeeseeseeeeeeseneeeeeeseenees 17 General information eisien a a aeo aa e aeiaai ta ieai 17 Overview of Setup Settings seesseeeseeereeeeresriserteerrterinserrnsrinsrrrnsrrnternt 17 Overview of Service settings ccccceeceeeeeeeeeeeneeseeeeeeeeeeeeeeeeseeeeeeseaeeeeaes 18 Call up Setup and Service settings ccccceeeeeeseeeeeeneeeeeeeeeeeeeeeeeneeeeeaes 20 Change settings i annee iaaa aiaa aaua a a 22 Remedying malfunctions cccccssseeeessseeeseseessssneneeeeeeeenssees 23 Safety information c ccccceceeeceeeceeeeeeeeeeeeeeeeseaaeeseeeeseaeeeesneeeeeeeeeseaeeesaas 23 ERROR UT Steet ecieic eevee a cladcaneiy itu saictepesteecterade dic Pestal S 23 Abbreviations of Error displays cccccecseeceeseeeeeeeeeneeeeseeeeeeeeeeeees 23 AV EL EMOls a5 icsiccteatstgesgs is ize teblaavecnalacesaaiceeecaud aceaniaceeespiaad Adicts aisha tits 24 BeErrOrs is cessiinidesatahacessedaishse
38. o 285 ERBE 55 170 7 Maintenance and servicing HF power output CUT Testing and measuring equipment ERBE Description Art No 20192 127 Patient cable AE or 20192 110 Patient cable AE international 20190 045 Electrode handle ICC ACC 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE 20196 045 Bipolar cable or 20196 053 Bipolar cable international 20100 034 Adapter cable bipolar HF power meter 20189 100 Dual pedal footswitch AUTO CUT Test setup DRY CUT HF power meter Fig 7 5 e The test specimen is connected to the power supply via the power cord e The levels of power are determined with the HF power meter The measuring cables are plugged into the HF power meter direct 56 170 Art Nr 80116 284 02 08 7 Maintenance and servicing Art Nr 801 16 284 02 08 Test procedure VIO 200 S 1 Set test specimen to AUTO CUT Effect 8 200 watts 2 Set HF power meter to RL 500 ohms 3 Activate test specimen via CUT button on the electrode handle 4 Determine and document measured value The tolerance range is 160 to 240 watts Test procedure VIO 300 S 1 Set test specimen to AUTO CUT Effect 8 300 watts 2 Set HF power meter to RL 500 ohms Activate test specimen via CUT button on the electrode handle 4 Determine and document measure
39. ome void It is recommended that the safety check also be performed by ERBE or persons trained by ERBE Only use original ERBE spare parts The manufacturer accepts no liability and the warranty rights becomes void if original spare parts are not used Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 2 e Modifications CHAPTER 2 Modifications Component affected As from VIO version 1 1 x Hardware Description of the modification IES 2 module The IES 2 smoke evacuation system can be attached to the VIO HF surgical unit and operated via said unit EIP 2 module The EIP 2 irrigation pump can be attached to the VIO HF Component affected Service settings surgical unit and operated via said unit Software Description of the modification New Service settings IES parameter EIP parameter Test programs New Test programs TP user interface Set EEPROM default 9 170 2 e Modifications Component affected HF Generator As from VIO version 1 2 x Hardware Description of the modification Development of a new HF generator module which will be recognized and supported by VIO S devices from software version 1 2 x onward Component affected Setup settings Software Description of the modification DRY CUT can be switched on and off independently of SWIFT COAG depending on the unit variant SWIFT COAG can be switched on and off independ
40. p The test specimen is connected to the power supply via the power cord On the test specimen the basic program is selected The single pedal footswitch is connected The dual pedal footswitch is connected The NE patient cable with the shorted adapter cable is connected to the NE receptacle on the test specimen Test procedure Assign the single pedal footswitch to any receptacle Press COAG pedal on the single pedal footswitch On the test specimen COAG must be activated Assign the dual pedal footswitch to any receptacle Press CUT pedal on the dual pedal footswitch On the test spec imen CUT must be activated Press COAG pedal on the dual pedal footswitch On the test specimen COAG must be activated Art Nr 80116 284 02 08 7 e Maintenance and servicing Art Nr 801 16 284 02 08 Fingerswitch activation Testing and measuring equipment PRPS Description Art No 20192 127 Patient cable AE or 20192 110 Patient cable AE international 20190 045 Electrode handle ICC ACC 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE Test setup e The test specimen is connected to the power supply via the power cord e On the test specimen the basic program is selected e The NE patient cable with the shorted adapter cable is connected to the NE receptacle on the test specimen Test procedure 20190 045 1 Connect the electrode handle wit
41. r connection Rated supply voltage 100 V 120 V 10 220 V 240 V 10 Rated supply frequency 50 60 Hz Line current 8A 4A Power input in standby mode 40 watts Power input with max HF output 500 watts 920 VA Terminal for grounding potential equalization yes Power fuses T8A T4A Operating mode Intermittent operation ON time 25 e g activated for 10 sec deacti vated for 30 sec Dimensions and weight Width x height x depth 410 x 165 x 380 mm Weight 8 8 kg Ambient conditions for transport and storage of unit Temperature 40 C to 70 C Relative humidity 10 95 Ambient conditions for operation of unit Temperature 10 C to 40 C Relative humidity 15 80 noncondensing 15 70 4 e Technical Data Acclimatizing If the unit has been stored or transported at temperatures below 10 C or above 40 C the unit will require approx 3 hours to acclimatize at room temperature Standards Classification according to EC Directive 93 42 Il b EEC Protection class as per EN 60 601 1 Type as per EN 60 601 1 CF 16 70 Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 5 e Setup and Service settings CHAPTER 5 Setup and Service settings General information This unit features two levels for changing settings e Setup level e Service level Overview of Setup settings Accessible to users and service personnel Setting Avai
42. r output CUT cccccceeeeseeeeeeeeeeeeeeeeeeteeneeeeseaes HF power output COAGULATE ccccecccseeeeeeeeeeeees Performance test upgrades cceeeeeeeeeeeeeeeeeeeeeeetenaes Monitor Circuits sis anaa dialami eda i 43 ETT 43 ETETE 43 Art Nr 80116 284 02 08 Art Nr 801 16 284 02 08 1 Safety information CHAPTER 1 Safety information Classification of the safety information WARNING The WARNING safety indication refers to a risk of personal injury CAUTION The CAUTION safety indication refers to a risk of damage to prop erty ATTENTION The ATTENTION safety indication refers to a risk which can cause equipment to become unserviceable IMPORTANT The IMPORTANT designation indicates application information and other particularly important information Knowledge of the User Manual The User Manual for this unit constitutes an integral part of this Ser vice Manual For performing servicing activities it is assumed that the reader has knowledge of the User Manual especially procedures for installation putting into operation and handling Protection from the risk of electric shock WARNING The supply voltage must match the voltage specified on the rating plate Connect the unit the equipment cart to a properly installed grounded outlet Only use the ERBE power cord or an equivalent power cord for this purpose The power cord must bear the national test sym
43. rs if an instrument with instrument recogni tion is connected B 9F Instrument has been dis Information no fault condi connected from the sys tion tem Occurs if an instrument with instrument recognition is disconnected from the system B AO No other mode can be set Information no fault condi for this instrument tion Occurs if the user wants to assign a different mode to an instrument with a fixed mode B A3 Footswitch not assigned Assign the footswitch acti Occurs if a footswitch vation which has not been assigned to an output receptacle is pressed B A4 Two footswitches are con Remove the duplicate foot nected Occurs if two foot switch from the unit switches of the same type are connected B AA No valid mode is assigned Information no fault condi Occurs if an output chan tion nel is activated without a mode being assigned to it B AB Activation is only possible Check the accessories If with a valid instrument the error persists notify Occurs if a MF receptacle ERBE Service is activated at which no instrument is recognized 30 170 Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 6 Remedying malfunctions Recognizing module B Control panel Recog nizing module Error code Additional infor mation Description Action B BO NESSY symmetry warning Check the NE accessories Occurs if the Nessy sym metry monitoring si
44. s Recognizing module C CPU Sensors Action Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service C 7D 7F C 81 84 C 91 92 C AO A1 C Co C FO Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service 34 70 Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 6 Remedying malfunctions D Errors Recognizing module D Smoke evacuation system IES 2 Recog Error Additional infor cae nizing code mation Description module D 80 Restart the unit If the error occurs again notify ERBE Service D 81 Excess temperature Overtemperature IES2 Let gt 60 C the unit cool down D 82 Insufficient temperature Undertemperature IES2 lt 0 C Leave unit on for several minutes without operating D 83 Restart the unit If the error occurs again notify ERBE Service D 86 Restart the unit If the error occurs again notify ERBE Service D 87 Obstruction Remove the suction tube from the tissue D 88 The filter is missing or Insert or replace the filter obstructed 35 170 6 Remedying malfunctions Err Errors Err Error
45. splays of the VIO Footswitch Errors lIF Errors Instrument Interface of corresponding receptacle slot Nessy2 Errors EIP 2 Errors ERBE Irrigation Pump 23 170 6 e Remedying malfunctions Status of ERROR list 02 08 A E Errors Recognizing module A APC 2 E Extension module VEM 2 Recog ke nizing Error Additional infor code mation Description Action module 01 Restart the unit If the error occurs again notify ERBE Service A E 02 04 Restart the unit If the error occurs again notify ERBE Service A E 05 Button error receptacle 1 Check the keyboard A E 06 Button error receptacle 2 Check the keyboard A E 07 09 OA 0B Restart the unit If the error occurs again notify ERBE Service Restart the unit If the error occurs again notify ERBE Service Information in test mode adjustment A E oC 0D Restart the unit If the error occurs again notify ERBE Service 10 Underpressure at selected gas input Check the gas supply tank pressure regulator If the error persists notify ERBE Service 11 Overpressure at selected gas input Check the gas supply tank pressure regulator If the error persists notify ERBE Service 24 170 12 13 Caloric and differential pressure sensor do not agree wrong gas Check the gas supply type of gas If the error persists
46. tarts up APC purge duration selection of period for which the instrument is purged with gas automatically 1 to 10 s APC purge flow selection of purge flow in at which the instrument is purged with gas automatically Purge flow relates to the default COAG Flow setting stored in the instrument Language V 1 0 x Self explanatory Start screen V 1 0 x Start screen type selection 18 70 Art Nr 80116 284 02 08 Art Nr 801 16 284 02 08 5 e Setup and Service settings Setting DRY SWIFT 2 Available from V 1 0 x to V 1 1 x Description ON Modes DRY CUT SWIFT COAG are used OFF Modes DRY CUT SWIFT COAG are used DRY CUT SWIFT COAG 2 V 1 2 x DRY CUT activated Mode DRY CUT is used DRY CUT deactivated Mode DRY CUT is used SWIFT COAG activated Mode SWIFT COAG is used SWIFT COAG deactivated Mode SWIFT COAG is used AUTO START V 1 0 x Setting to specify whether AUTO START is permitted as an activation mode Test programs IES parameter V 1 0 x V 1 1 x Selection of hardware test programs Setting the parameters for operation of the IES 2 smoke evacuation system EIP parameter V 1 1 x Setting the parameters for operation of the EIP 2 irrigation pump 1 Safe config saves the unit receptacle configuration recognized by the system The receptacle configuration must be saved
47. tify The measurement current ERBE Service for analysis of the instru ment recognition is too high 2 3 5 6 OC 0E Restart the unit If the error Buchse occurs again notify ERBE Service 2 3 5 6 OF U Coag error 12 V volt Check the accessories If Buchse age during Coag activation the error persists notify too low ERBE Service 2 3 5 6 70 72 Restart the unit If the error Buchse occurs again notify ERBE Service 2 3 5 6 81 Short circuit instrument rec Check the accessories If Buchse ognition R The resistor the error persists notify value determined for the ERBE Service instrument recognition cor responds to a short circuit 2 3 5 6 82 Short circuit activation rec Check the accessories If Buchse ognition R_NEU The resis the error persists notify tor value determined for the activation recognition corre sponds to a short circuit ERBE Service 38 170 Art Nr 80116 284 02 08 Art Nr 80116 284 02 08 6 Remedying malfunctions Recognizing module 2 3 5 6 IIF Instrument Interface of corresponding receptacle slot Recog nizing module Error code Additional infor mation Description Action 2 3 5 6 83 No load activation recogni Check the accessories If Buchse tion R_NEU The resistor the error persists notify value determined for the ERBE Service activation recognition corre sponds to no load 2 3 5 6 84 Instrum
48. ue must be gt 2 MOhm Document the measured value Performance tests Testing and measuring equipment PRBE Description Art No 20189 100 Dual pedal footswitch 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE Test setup The test specimen is connected to the power supply via the power cord The dual pedal footswitch is connected The NE patient cable with the shorted adapter cable is connected to the NE receptacle on the test specimen Test procedure 1 2 Check power switch for smooth operation The power switch must be easy to operate and must neither stick nor scrape Press power switch The power switch must snap into the ON position and the test specimen must perform a system start The test specimen must perform the system start without error message s The test specimen must emit an acoustic signal acknowledge ment tone during the self test Art Nr 80116 284 02 08 Art Nr 801 16 284 02 08 7 e Maintenance and servicing Pushbuttons acknowledge ment tone when pressed Software download Neutral electrode setting Date and time Display LEDs Activation tones Check all the pushbuttons focus buttons selection buttons buttons on the test specimen to make sure they are working properly Press each button at least twice When pressing the buttons there must be an acoustic signal every time ackno
49. wledgement tone Document whether a software update was performed Call up service level See page 20 Then call up the neutral electrode setting and document the existing setting Remain in the Service level Then call up the date and time settings one after the other check the existing settings and correct them if required Display 1 Check the backlighting of the display to make sure it is operating properly If backlighting is faulty no image will be visible LEDs 1 l Upon system start all the LEDs and seven segment displays must light up briefly with equal brightness In the case of the neu tral electrode receptacle red and green must light up briefly one after the other Press CUT pedal on the dual pedal footswitch at least twice When pressing the pedal there must be an acoustic signal every time acknowledgement tone Press COAG pedal on the dual pedal footswitch at least twice When pressing the pedal there must be an acoustic signal every time acknowledgement tone 49 170 7 Maintenance and servicing Single pedal footswitch 50 70 activation COAG Dual pedal footswitch activation CUT COAG Footswitch activation Testing and measuring equipment PRPS Description Art No 20188 100 Single pedal footswitch 20189 100 Dual pedal footswitch 20194 070 Patient cable NE or 20194 075 Patient cable NE international 20100 033 Adapter cable NE Test setu
Download Pdf Manuals
Related Search