Home

Installation

1. Center Position 2 point type seat belt anchor on body lt lt FRONT SEAT BELT gt gt Automatic Belt 11 2 Nm 8 1 ft lb only these 8 bolts for ECLIPSE 11 2 Nm 8 1 ft lb only these 8 bolts for MIRAGE lt lt REAR SEAT BELT gt gt Outboard Position 3 point type seat belt retractor on side structure Outboard Position 2 point type seat belt 11 2Nm 8 1 ftlb ZY only these 8 bolts for ECLIPSE R retractor on shelf panel lt lt REAR SEAT BELT gt gt Center Position 3 point type seat belt retractor on body Center Position 2 point type seat belt anchor on body retractor on seat anchor on seat Usage amp Maintenance To protect you and your passengers in the event of an accident it is the most important that the seat belts be worn correctly while driving WARNING e Always place the shoulder belt over your shoulder and across your chest Never put it behind you or under your arm e One seat belt should be used by only one person Doing otherwise can be dangerous e Seat belts should always be worn by every adult who drives or rides in this vehicle and by all children who are large enough to wear seat belts properly Other children should always use proper child restraint systems e Remove any twists when using the belt e No modifications or additions should be made by the user which will either prevent the seat belt adjusting devi
2. typical seat belt layout The shape amp installation position may be slightly different for each vehicle Please refer to the vehicle service manual amp owner s manual for detail FOR SEAT BELT WITH ELECTRICAL PRE TENTIONER lt CONNECTOR TYPE 1 gt DISCONNECTION Use a flat tipped screwdriver 1 to unlock the locking button 2 of the floor wiring harness side connector 3 After releasing the lock disconnect the connector CONNECTION Connect the pre tensioner connector then securely lock the locking button 2 of the harness side connector 3 lt CONNECTOR TYPE 2 gt DISCONNECTION Disconnect the connector after releasing the lock by pulling up the locking lever 1 of the harness side connector 2 CONNECTION Connect the pre tensioner connector then securely lock the locking lever 1 of the harness side connector 2 lt lt FRONT SEAT BELT gt gt Outboard Position 3 point type seat belt lap anchor on seat XP YS buckle anchor on body x 1 SEAT BELT PRE TENSIONER CONNECTOR if so equipped lap anchor on body In case of Mechanical Pre tensioner After fastening lower bolt push up stopper lever 3 to A direction rotating lock plate 2 to B direction and fix it by tapping screw with upper stay bracket 1 After installing the retractor pull the lever 4 to Y direction with pushing down to X direction and rotate it to Z direction
3. G WARNING e All seat belt assemblies including retractors and attaching hardware should be inspected by an authorized Mitsubishi Motors dealer after any collision We recommend that seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly e Do not attempt to repair or replace any part of the seat belt assemblies this work should be Emergency release button if so equipped done by an authorized Mitsubishi Motors dealer Failure to have an authorized Mitsubishi Motors dealer perform the work could reduce the effectiveness of the belts and could result in serious If the shoulder belt sliding anchor is locked in an injury in the event of a collision emergency push the emergency release button 1 to e Once the pre tensioner has activated it cannot be re used release the shoulder belt Use this button only when It must be replaced together with the retractor the shoulder belt prevents you from leaving the car in an accident NOTE e For further information please refer to vehicle owner s manual WARNING e To maintain the normal shoulder belt restraint do not press the emergency release button except in an emergency Seat belt extender if so equipped When your seat belt even fully extended is not long enough a seat belt extender must be obtained e The extender should only be used if the existing belt is n
4. Installation Pre removal and Post installation Operation e Turn the ignition key to the LOCK OFF position e Disconnect the negative battery terminal e Wait at least 60 seconds after disconnecting the battery cable before doing any further work e Observe existing belt installation before removal e To install reverse the sequence of removal e Do not damage belts while installing e Do not install the belts while webbing are twisted e Use only new bolts and nuts The tightening bolts or nuts are classified into 3 types by thread diameter Each tightening torque is as follows unless otherwise shown in following sketches Nominal diameter of the thread Tightening torque 10 mm or 7 16 inches 43 8 Nm 32 6 ft lb 8mm 19 3 Nm 14 2 ft lb 6mm 5 0 1 0 Nm 44 9 in lb e After completing installation re check to ensure each belt has been properly installed Make sure seat belts latch securely Make sure rotary anchor parts rotate properly if so equipped Make sure retractor operates smoothly and locks when pulled sharply if it has a sensor of the acceleration of seat belt extraction if so equipped Make sure SRS indicator warning light illuminates for approximately seven seconds and goes out after turning the ignition switch to the ON position if pre tensioner is equipped Make sure seat belt warning light reminder works properly if so equipped e Following sketches are examples of
5. ces from operating to remove slack or prevent the seat belt assembly from being adjusted to remove slack e Never hold a child in your arms or on your lap when riding in this vehicle even if you are wearing your seat belt To do so risks severe or fatal injury to your child in a collision or sudden stop e Always adjust the belt to a snug fit e Always wear the lap portion of the belt over your hips 3 point type seat belt and lap belt with emergency locking mechanism This type of belt requires no length adjustment Once worn the belt adjusts itself to the movement of wearer but in the event of a sudden or strong shock the belt automatically locks to hold the wearer s body The belt also locks when the vehicle accelerates or decelerates quickly or when the vehicle is on a steep slope or when the belt is pulled sharply If it has a sensor of the acceleration of seat belt extraction you can check the belt locks when you pull it sharply To fasten 1 Pull the seat belt out slowly while holding the latch plate WARNING e Never wear the lap portion of the belt across your abdomen During accidents it can press sharply against abdomen and increase the risk of injury 3 Pull the belt slightly to adjust slackness as desired NOTE e In the case that the seat belt is equipped with an automatic locking retractor ALR mechanism If you pull the seat belt fully out of the retractor the retractor will switch to its ALR child restrai
6. nt installation mode and lock thus preventing further movement If this happens you should switch the retractor back to its emergency locking retractor ELR mode by taking off the seat belt and fully rewinding it You should then wear the seat belt again To unfasten Hold the latch plate and push the button on the buckle NOTE e As the belt retracts automatically keep the latch plate held while retracting so that the belt stows slowly Failure to do this could damage the vehicle Lap belts manual belt if so equipped The lap belts should be adjusted by holding the belt and latch plate at right angles to each other and then pulling the belt as shown in the illustration 1 Tighten or 2 Loosen to a snug fit around the occupant While holding the latch plate insert the latch plate into the buckle until a click is heard Pregnant women WARNING e Seat belts work for everyone including pregnant women Pregnant women should use the available seat belts This will reduce the likelihood of injury to both the woman and the unborn child The lap belt should be worn across the thighs and as snug against the hips as possible but not across the waist Consult your doctor if you have any additional questions or concerns Automatic shoulder belt The shoulder belt moves automatically to the set fasten position when a door is closed and the ignition key is turned to the ON position When the door is opened
7. ot long enough Anyone who can use the standard seat belt should not use an extender Unnecessary use of an extender can adversely affect seat belt performance in an accident e When not required the extender must be removed and stowed
8. the shoulder belt automatically moves to the off unfastened position For the driver s seat the shoulder belt automatically moves to the set off position when the ignition key is removed from the ignition To fasten 1 Get in the car close the door and adjust the seat position 2 Grasp the seat belt lap portion belt latch plate and pull the webbing then push the latch plate into the buckle until a click is heard of an abrupt change in car motion 3 Turn the ignition key to the ON position the shoulder belt will move automatically to the set Inspection amp fasten position 4 Pull up the shoulder belt and seat belt slightly to be sure that there is no excess slack or tightness e Check the belts for cuts worn or frayed webbing and for cracked or deformed metallic parts in the belts The belts will retain a small amount of looseness necessary for comfort during driving Replace the belt assembly if defective If a belt is too tight pull it up slightly and let it return The belts will not tighten during normal use e A dirty belt should be cleaned with neutral detergent in warm water After rinsing in water let it dry in the therefore you can set them once for safe comfortable snugness shade 5 The belts will allow unrestricted movement under normal conditions The belts will lock in the event Do not attempt to bleach or re dye the belts because this affects their characteristics of an abrupt change in car motion WARNIN

Installation

Contents

Download Pdf Manuals

Related Search

Related Contents