Loctite "Do-it-Right" - New
Contents
1. ACTIVE SURFACE PRIMER NOT REQUIRED INACTIVE SURFACE PRIMER REQUIRED Brass Copper Aluminium Black Oxide Bronze lron Stainless Steel Anodised Magnesium Passivated Surfaces Zinc Titanium Nickel CHARACTERISTICS ADVANTAGES OF ANAEROBIC THREAD SEALING Anaerobic thread sealants flow into and completely fill all voids eliminating leak paths Anaerobic thread sealants seal and threadlock simultaneously Thread sealants work on all size and types of fittings see quick selector Thread sealant strength is selectable Medium or Low depending on requirements Thread sealants can be disassembled with normal tools Loctite 55 is a non curing impregnated nylon cord IMPORTANT NOTE Do not use anaerobic sealants on plastic pipe or plastic fittings For plastic fittings use Loctite 55 LOCTITE MAINTENANCE PRODUCTS PUNCTURE SEALING Co N 90 SE Ose D lu Roughened I I I I Epoxy Layer 2 Y I Ql NN Layer 1 2 A 2 _ Disc Potch Tank Wall IMPORTANT TAKE PROPER SAFETY PRECAUTIONS WHEN WORKING WITH FLAMMABLE LIQUID TANKS AVOID USE WITH COMPRESSIBLE GASSES Clean the repair area with Loctite ODC Free Cleaner amp Degreaser Roughen a 25mm 50mm radius around hole with emery cloth Clean again Prepare a metal disc patch slightly larger than hole Mix Loctite 5 Minute Epoxy A and B as per d2. SELECTED LOCTITE PRODUCT 243 on both sides of gasket Primer on flange 243 surface only 243 1 Remove old gosketing material and other heavy contaminants with Loctite CHISEL Gasket Remover Use mechanical removal technique if required Note Avoid grinding 2 Clean both flanges with Loctite ODC Free Cleaner amp Degreaser Spray Loctite Primer Refer Technical Data on both flange faces Allow to dry 4 Smear SELECTED LOCTITE PRODUCT to both sides of precut gasket with a clean applicator 5 Place coated gasket on flange surface and assemble parts immediately Note If cover bolts into blind holes as above apply 243 Threadlocker into hole and on threads Tighten normally If through bolt assembly apply 243 Threadlocker to bolt threads only 6 Tighten as per standard practice A LOCTITE MAINTENANCE PRODUCTS FLANGE SEALING PRODUCT 510 515 518 GASKET MASTER MASTER ELIMINATOR GASKET GASKET Flange Type Rigid Rigid Rigid Alloy Temperature 55 to 200 55 to 150 55 to 150 Gap Fill mm up to 0 25 up to 0 5 up to 0 5 Cure Speed Medium Medium Fast Optional Primer 7471 7649 7649 Viscosity c P 12 000 262 500 800 000 Oil Resistance Excellent Excellent Excellent Petrol Resist Excellent Excellent Excellent WHEN TO USE PRIMERS Primers are used when the surfaces to be sealed are not active enough to cause curing to take plac
3. Note Virtually any Loctite Threadlocking product will work here Low strength liquid is recommended due to normal gap and strength requirement 4 Install as usual Wipe off excess 6 Allow to cure 30 minutes prior to service Note Loctite 243 Threadlocker is normally used with worn seal housings to prevent leakage or slippage t is not generally necessary to remove pre applied sealant from seal O D EE M Di LOCTITE MAINTENANCE PRODUCTS RETAINING COMPOUNDS Application Product Primer Shaft Mount Press fit Retaining Compound 609 NONE Shaft Mount Slip Fit Small Gap 0 05mm Radial max Retaining Compound 609 T 7471 Larger Gap 0 5mm Radial max QUICK METAL 660 7471 Maximum Strength 0 2mm Radial Retaining Compound 680 7471 Maximum Temperature 200 C Retaining Compound 620 7 7471 or 0 2mm Radial max N 7649 Housing Mount Press Fit Maximum Strength Retaining Compound 609 NONE Medium Strength Bearing Mount 641 NONE Housing Mount Slip Fit Maximum Strength Retaining Compound 680 7471 High Strength Retaining Compound 609 7471 Medium Strength Bearing Mount 641 N 7649 Note Softer metals Aluminium Bronze etc provide lower shear strengths than ferrous components Excessive gap reduces shear strengths Ideal surface finish 0 8 to 3 2 microns 50 to 80 rms Refer to Technical Data Sheets for more information I LOCTITE DO IT R
4. Slip fits Steel Aluminium Bronze can equal press fit strength Unitised assemblies are stronger and resist micro movement key wallow High strength retained assemblies can be dissassembled with heat approx 230 C to 300 C IMPORTANT NOTE Do not use anaerobic retaining compounds on most thermoplastics ABS PVC etc Softening and or stress cracking may occur Anaerobic retaining compounds can be used with 7471 or 7649 Primer on nylon and thermoset plastics LOCTITE MAINTENANCE PRODUCTS BONDING l JOB EVALUATION Answer These Questions A C D E What materials are to be bonded What kind of rubber plastic etc Porous Slick Rough What kind of service Operating temperature Impact Moisture or water exposure What kind of stresses Avoid peel or cleavage Is gap filling or bridging needed How much What cure speed or return to service time is needed Il ADHESIVE SELECTION See page 36 Ill SURFACE PREPARATION 1 N 5 Part must be cleqn No oil No grease No residue Remove paint from bond area for maximum strength Roughen smooth surfaces with emery cloth Treat selected hard to bond materials as directed a Polyethylene etc Use Loctite Prism Primer 770 and adhesive 401 or 406 b PTFE Use appropriate etching agent Clean parts with ODC Free Cleaner IV APPLICATION TECHNIQUES TIPS A B C D Read and follow adhesive packag
5. Threadlocker strength is selectable High Medium Low depending on requirements Threadlockers improve breakaway and prevailing torque Threadlockers lock and seal preventing corrosion and leakage High strength threadlockers can be disassembled with heat 230 C for 5 minutes IMPORTANT NOTE Do not use anaerobic threadlockers on most thermoplastics ABS PVC etc Softening and or stress cracking may occur Anaerobic threadlockers can be used with 7649 Primer on Nylon and thermoset plastics All anaerobic threadlockers have high chemical resistance LOCTITE MAINTENANCE PRODUCTS THREADSEALING POTABLE WATER OR AIR _ Loctite Product Loctite Product Clean parts of contamination with ODC Free Degreaser Cleaner If necessary spray Loctite Primer Refer to Technical Data onto threaded parts male and female Allow to dry Note Primer is not required for brass parts Apply a band of Loctite Product to male threads starting one to two threads from end of pipe Assemble parts snugly Do not overtighten If initial pressure exceeds 6 9 MPa wait 30 minutes before pressurizing Note For stainless steel components use PST Pipe Sealant 567 For general purpose thread sealing use PST Pipe Sealant 567 For fine filtration systems requiring zero contamination use Hydraulic Pneumatic Sealant 569 If sealing chemicals or strong acids bases refer to Fluid Compatibility
6. HOUSED COMPONENTS 660 or 641 Dab 660 or 641 Dab 660 or 641 Dab Housing ORIGINAL Select component to fit shaft Machine to reduce component O D or increase housing I D to permit approximate 0 05mm 0 1mm diametral slip fit Clean all parts with Loctite ODC Free Cleaner amp Degreaser and spray with Loctite Primer Refer to Technical Data Apply several Loctite 641 dabs to component O D Avoid touching bottle tip to metal Install component Do not rotate Wipe off excess Allow five minutes cure time prior to service WORN Procedures identical to original slip fit except T 2 Determine the maximum radial If the maximum gap exceeds 0 1mm use QUICK METAL 660 and 7471 Primer T Take steps to maintain concentricity on large gaps Large gaps require longer cure times 30 60 minutes QUICK METAL 660 is NOT recommended for radial gaps exceeding 0 5mm es LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS HOUSED COMPONENTS SLIP FIT HEAVY DUTY Q Housing 609 or 680 ORIGINAL 1 Select component to fit shaft 2 Machine to reduce component O D or housing l D to permit approximate 0 05mm 0 1mm diametral slip fit Clean all parts with Loctite ODC Free Cleaner amp Degreaser Do NOT use Primer Apply Loctite 609 or 680 coating to component O D Install component with twisting motion Wipe off
7. For prod uct availa bility technical information dnd material safety data sheets MSDS call Henkel Australia Pty Ltd 1 Clyde Street Silverwater NSW 2128 Ph 1300 88 555 6 Fax 02 9525 5643 Or visit Loctite at www loctite com au Prism Quick Metal Master Pipe Sealant Yuk Off Blue Maxx Black Maxx Copper Maxx Grey Maxx and Pak are Trade Loctite g ma yir Z Registered Trade Mark of Henkel Loctite USA Trade Marks of their respective owners ART0404A 2 1995 Henkel Australia Pty Ltd Specifications subject to without notice ESAE A Do lt Right 1 _ Users Guide ape The when where and how to use Loctite maintenance products ry i 4 i r ja y A f QA S ES VE cts 4 LOCTITE MAINTENANCE PRODUCTS CONTENTS FC N The primary function of this User s Guide is to help you the maintenance professional with the proper selection and use of Loctite products A wide variety of preventative maintenance as well as repair techniques are explained in step by step detail Consider this a supplemental service manual for every piece of equipment in your plant Our goal is to make it easier for you to use our products to your benefit for faster repair times reduced downtime and extended equipment life Additional information on these products as well as others is available by contacting your local Loctite adhesive
8. METAL FLARED SWAGED FITTINGS 567 Coating For damaged flare or seat 567 Band 1 Disassemble and if necessary spray all components with Loctite 7649 Primer N Allow to dry 2 Apply a thin coating of PST Pipe Sealant 567 to fitting face 3 Apply a band of PST Pipe Sealant 567 to male threads 4 Assemble parts snugly LOCTITE MAINTENANCE PRODUCTS THREADSEALING Loctite Product Band U TIB ili E 2 If necessary spray adapter threads with Loctite Primer Refer to Technical Data Allow to dry _ 2 Insert barbed hose stem into hose I D with slight twisting motion 3 Install appropriate hose clamp 4 Apply a band of Loctite Product to male hose stem threads upon installation or adding accessory device Tighten snugly Note Loctite Product may attack synthetic rubber tubing THREAD SEALING QUICK SELECTOR TAPERED THREADS Instant Max Max Temp Application Product Primer Seal Pressure Steam Range Stainless Steel PST Pipe N 7649 3 4MPa 24 Hours 0 9MPa 55 C to and All Other Sealant 567 500 PSI 69MPa 130 PSI 205 C Metal Fittings 10 000 PSI High Filtration Hydraulic T 7471 10 Mins 24 Hours 55 C to Zero Contamina Pneumatic 3 4MPa 69MPa 150 C tion Systems Sealant 569 500 PSI 10 000 PSI Potable Universal N 764910 Mins 24 Hours 55 C to Water Systems Sealant 577 3 4MPa 69MPa 150 C 500 PSI 10 000 PSI Potable 55 Sealing Instant Instant N A 55 C t
9. etc An Instant Adhesive used with spray mist Accelerator 7452 Components on PC boards metal plastic rubber etc 324 An Impact Resistant Structural Adhesive for gaps up to 1mm Used with Activator 7075 Metal timber glass 330 Multibond A Structural Adhesive for gaps up to 0 5mm Used with Activator 7387 Metal plastic timber glass etc 3801 A five minute general purpose two part clear epoxy Metal timber ceramic concrete fibreglass etc 3805 A high strength two part Steel and Aluminium Epoxy Filler suitable for gap filling PE LOCTITE DO IT RIGHT USERS GUIDE Metal timber ceramic concrete LOCTITE MAINTENANCE PRODUCTS RUSTPROOFING MUM USE OF EXTEND RUST TREATMENT SURFACE PREPARATION OLD STEEL Loose or flaky rust must be removed Only conversion of firmly bonded rust will result in durable protection Oil grease old paint mill scale form oil fingerprints and water soluble surfaces and chlorides must be removed to allow Loctite Extend to react with rust Loose rust mill scale and oil paint should be removed preferably by power wirebrushing followed by rinsing with water to remove powder and solubles Manual wirebrushing chipping scraping and particularly rotopeening can also be used Ideal surfaces will show light rust as well as bare metal surfaces RUST CONVERSION TIME AND APPEARANCE Two coats of Loctite Extend are recommen
10. METAL PRESS FIT REPAIR 6 ml tube 66010A 50 ml tube 66040A 680 HIGH STRENGTH HIGH VISCOSITY 50 ml bottle 68050 250 ml bottle 68070 641 BEARING MOUNT 10ml bottle 21314 50ml bottle 21315 250ml bottle 21316 E LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS ORDERING CATEGORY SIZE ITEM NO GASKETING 510 GASKET ELIMINATOR HIGH TEMPERATURE 50 ml tube 25555A 250 ml tube 25554 515 MASTER ELIMINATOR 6 ml tube 51517 50 ml tube 51531A 300 ml cartridge 33530 518 FLANGE SEALANT ml tube 51817 25 ml syringe 51827 50 ml tube 25583A 300 ml cartridge 51845 5900 INSTANT GASKET aerosol 198g can 30507 5900 HEAVY BODIED BLACK SILICONE 390g cartridge 20166 5910 BLACK MAXX RTV SILICONE GASKET MAKER 95g tube 34250 390g cartridge 20166 587 BLUE MAXX RTV SILICONE GASKET MAKER 95g tube 34848 370g cartridge 34888 5920 COPPER MAXX RTV SILICONE GASKET MAKER 85g tube 34249 5699 GREY MAXX RTV SILICONE GASKET MAKER 95g tube 34238 420g cartridge 18581A ADHESIVES 330 MULTIBOND NO MIX 300 ml cartridge 33064A Also see Activator 7387 406 25ml bottle 40633 25 100ml bottle 33533 500ml bottle 33534 401 25ml bottle 40124 25 100ml bottle 33531 500ml bottle 33532 3g tube 16704A 454 PRISM SURFACE INSENSITIVE GEL 3 gm tube 45404 20 gm tube 45416A 200g tube 45474 480 PRISM TOUGHENED 25ml bottle 16819 25 500g bottle 16887 5 MINUTE EPOXY 29 5ml syringe 20981 Various Epoxies LOCTITE MAINTENANCE PRODUCTS ORDERING
11. excess o INE Os Ue 0 Allow 2 hours cure time prior to service WORN Procedures are identical to original slip fit except 1 Determine the maximum radial gap 2 If the maximum radial gap exceeds 0 1mm use QUICK METAL 660 and Loctite 7471 Primer T 3 Take steps to maintain concentricity on large gaps 4 Large gaps require longer cure times 30 60 minutes 5 QUICK METAL 660 is NOT recommended for radial gaps exceeding 0 5mm DISASSEMBLY Pull as usual 2 If necessary apply localized heat 230 C for five minutes 3 Pull while hot LOCTITE MAINTENANCE PRODUCTS HOUSED COMPONENTS Z 480 Shims Shim EXCESSIVE EVEN WEAR Clean parts with ODC Free Cleaner Position the component in bore Select three equilateral mounting points Determine the radial gap at those points Select appropriate shim stock Cut three pieces approx 3mm wide to fit bore depth Bond the shims to bore at mounting points using Loctite 480 99 M v aN Assemble per instructions page 29 P j LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS HOUSED COMPONENTS 1 Clean the housing I D and seal O D with Loctite ODC Free Cleaner amp Degreaser 2 Spray both the housing and seal with Loctite 7471 Primer T 3 Apply a bead of Loctite 243 Threadlocker to the leading edge of metallic seal O D Avoid touching bottle tip to metal 243 Bead
12. within 10 minutes by pressing together Tighten as required 5 Clean up any excess 6 Cure times will vary with temperature humidity and gap Typical full cure time is 24 hours LOCTITE MAINTENANCE PRODUCTS FORM IN PLACE GASKETING MAXX SERIES SILICONES LOCTITE MAXX SERIES SILICONES QUICK SELECTOR PRODUCT COPPER INSTANT MAXX GASKET Flange Type Flexible Flexible Japanese Vehicle Flexible Flexible Temperature 60 to 260 C 60 to 200 60 to 200 60 to 316 60 to 200 C Gap Fill mm 6mm 6mm 3mm 6mm 6mm Sensor Safe Yes Yes Yes Yes Yes Cure Tack Free 30 min 5 min 10 min 60 min 5 min Full Cure 24 hrs 24hrs 24 hrs 24 hrs 24 hrs Oil Resistance Excellent Excellent Excellent Excellent Excellent Instant Seal No Yes No No Yes 1 Continuous service Intermittent temperature higher than established range 2 Seals instantly at zero gap Note Silicones used at extreme high temperatures can seal but lose various properties REASONS TO USE MAXX SERIES SILICONES INSTEAD OF STANDARD RTV SILICONES LOCTITE MAXX SERIES SILICONES WILL NOT CORRODE STEEL OR ALUMINIUM Standard RTV acetoxy silicones vinegar smell should not be used to seql closed systems boxes electricol boxes etc Acetic qcid will corrode internal parts bearings contacts etc LOCTITE MAXX SERIES SILICONES ARE 8 TIMES MORE OIL RESISTANT THAN STANDARD RTV SIL
13. 22 SUPER SCREW LOCK 243 SUPER NUT LOCK 262 SUPER STUD LOCK up to M3 277 HIGH STRENGTH over M36 290 SUPER WICK IN up to M20 Strength Breakaway Prevail Torque N m on MIO Temperature 6 4 20 7 High 22 32 High Medium 32 32 10 29 Thixotropic Liquid Thixotropic Liquid Thixotropic Liquid Range C 55 to 150 55 to 150 55 to 150 55 to 150 55 to 150 Cure Speed Slow Med Medium Medium Slow Medium Primer 7471 7471 7649 7649 7649 Colour Purple Blue Red Red Green Viscosity c P 1 200 2 250 1900 7 000 20 WHEN TO USE PRIMERS Primers are used when the surfaces to be threadlocked and sealed are not active enough to cause curing to take place or when the cure is required to be accelerated The table below shows common materials and when to use primer Select the correct primer from the above ACTIVE SURFACE PRIMER NOT REQUIRED INACTIVE SURFACE PRIMER REQUIRED Brass Copper Aluminium Black Oxide Bronze Iron Stainless Steel Anodised Magnesium Passivated Surfaces Zinc Titanium Nickel CHARCTERISTICS ADVANTAGES OF ANAEROBIC THREADLOCKERS Flat washer can still be used with threadlockers Threadlockers lubricate threads for proper assembly torque tension ratio Threadlockers work on all size and types of fasteners SAE or Metric
14. CATEGORY SIZE ITEM NO PRIMERS 7471 PRIMER T Acetone 2L Can 24062 125g 21356 7649 PRIMER N Acetone 2L Can 24063 100ml 22410 770 PRISM PRIMER Heptane 100ml bottle 29520 1L Can 24377 7387 330 ACTIVATOR 100ml 24058 T 24059 7452 TAK PAC ACCELERATOR 20g aerosol 21520 1L 24064 LUBRICANTS C5 A COPPER ANTI SEIZE 3 63Kg Can 51009 453g brush top 51007 aerosol 51003 NICKEL ANTI SEIZE 771 28g Tube 28182A 454g 77164 SILVER GRADE ANTI SEIZE 250g tube 76741 454g brush top 76764 200g aerosol 76756 5kg pail 76731 10kg pail 76785 236ml brush top 76732 CLEANERS YUK OFF ORANGE pumice formula lotion 400ml bottle 31908 4L pump bottle 31909 15L pump 31910 ODC FREE CLEANER amp DEGREASER 473ml pump spray 20162 GENERAL MAINTENANCE EXTEND RUST TREATMENT 18 9L 75465 946ml bottle 75430 3 75L bottle 75448 FORM A THREAD STRIPPED THREAD REPAIR 13 1 ml syringe STR1 O RING SPLICING KIT Inch Kit 10361 O RING SPLICING KIT Metric Kit 16224A FIXMASTER METAL MAGIC STEEL STICK 113g 98853 LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS TROUBLESHOOTING 1 What type failure is occurring Has the application worked before Was proper and adequate adhesive sealant used Was proper and adequate primer activator used Do service conditions exceed the capability of the adhesive sealant a operating temperature c fluid compatibility b excessive pressure too soon 5 Were parts ad
15. Chart in 567 brochure If sealing potable water system use universal pipe sealant 577 or 55 Pipe Sealing Cord Do not use on oxygen or strong oxidizers chlorine Do not use Loctite 567 or 577 on PVC or ABS pipe Use Loctite 55 Depending on conditions METAL PIPE UNIONS 2 3 4 LOCTITE DO IT RIGHT USERS GUIDE 567 Band 567 Band 567 Band cra ipic 567 Coating May be used for badly damaged seat Disassemble and if necessary spray all components with Loctite 7649 Primer N Allow to dry Apply a thin coating of PST Pipe Sealant 567 to union face Apply a band of PST Pipe Sealant 567 to male threads Assemble parts snugly LOCTITE MAINTENANCE PRODUCTS THREADSEALING METAL COMPRESSION FITTINGS 567 Coating 567 Band 567 Band 1 Clean parts Slide fitting nut and ferrule back approximately 20mm from end of tubing 2 If necessary spray the entire assembly with Loctite 7649 Primer N Allow to dry Note Primer is not required for brass parts 3 Apply a thin coating of PST Pipe Sealant 567 to tubing where ferrule will be located 4 Slide ferrule forward over PST Pipe Sealant 567 coated tubing then apply a thin bead of PST Pipe Sealant 567 coating to ferrule 5 Slide ferrule forward over 567 coated tubing es Apply a small band of PST Pipe Sealant 567 to male threads 7 Assemble and tighten normally Note Do not use on plastic fittings or tubing
16. DATA 33 BONDING GUIDE TO SUCCESSFUL BONDING 34 PROPER JOINT DESIGN 35 ADHESIVE QUICK SELECTOR 36 RUSTPROOFING OPTIMUM USE OF EXTEND RUST TREATMENT 37 CLEANING ODC FREE CLEANER HAND CLEANING 38 MAKING O RINGS 39 ORDERING PRODUCT LISTING 40 41 42 TROUBLESHOOTING CHECKLIST 43 LOCTITE MAINTENANCE PRODUCTS THREADLOCKING Apply Here 1 Clean all threads bolt and nut with Loctite ODC Free Cleaner amp Degreaser 2 If necessary spray all threads with Loctite Primer Refer to Technical Data Allow to dry 3 Select the proper strength Loctite Threadlocker product 4 Insert bolt into through hole assembly 5 Apply several drops of Threadlocker onto bolt at targeted tightened nut engagement area Avoid touching bottle tip to metal 6 Assemble and tighten nut as usual BLIND HOLES CAP SCREWS ETC Onto Thread Onto Threads A lt NS 1 Clean all threads BS and with Loctite ODC Free Cleaner amp Degreaser N If necessory spray bolt and hole with Primer Refer to Technical Data Allow to dry Select the proper strength Threadlocking product Squirt several drops down the sides of the female threads Apply several drops to bolt Avoid touching bottle tip to metal Tighten as usual Note Using Loctite Threadlockers will virtually eliminate stripped threads in aluminium or magnesium housings caused by galvanic corrosion B LOCTITE DO IT RIGHT USERS GUIDE oe LOCTITE MA
17. ICONES Standard RTV silicones should not be used to seal Hot Oil systems oil pan etc They swell and lose sealing ability REASONS TO USE LOCTITE ANAEROBIC GASKETING PRODUCTS 510 515 OR 518 INSTEAD OF STANDARD RTV SILICONES LOCTITE ANAEROBIC GASKETING PRODUCTS ARE RESISTANT TO GASOLINE AND FUEL OILS Silicones should not be used to seal fuel systems They swell and lose sealing ability LOCTITE ANAEROBIC GASKETING PRODUCTS RESIST BLOW OUT Silicones are not recommended for high pressure applications Bs LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS STRENGTHEN KEYED ASSEMBLIES 4 _ 243 dab here r 641 Coating Here 641 ASSEMBLY 1 Clean all parts with Loctite ODC Free Cleaner amp Degreaser 2 If necessary spray all parts 1 0 and O D with Loctite Primer Refer Technical Data Apply Loctite 641 coating into keyway and on key ae Apply dab s of 641 onto shaft opposite keyway or evenly spaced around shaft Avoid touching bottle tip to metal Assemble parts Wipe off excess Apply 243 dab to set screw Tighten set screw Oa So Allow 5 10 minutes cure time prior to service Note LOCTITE 641 is NOT recommended for radial gaps exceeding 0 2mm on shaft or keyway See BADLY WALLOWED KEYWAY for procedure page 23 DISASSEMBLY Tap component and key with hammer 2 Pull as usual LOCTITE MAINTENANCE PRODUCTS STRENGTHEN KEYED AS
18. IGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS RETAINING PRODUCT 641 609 620 680 BEARING MEDIUM HIGH HIGH VERY HIGH MOUNT STRENGTH TEMPERATURE STRENGTH Strength Low Medium High HIgh High Very High Shear Strength Nominal N mm 7 to 16 16 to 30 17 to 37 15 to 30 28 Temperature gg o 150 55to 150 55 230 55 150 55 to 150 Gop Fill mm up to 0 2 up to 0 2 up to 0 25 up to 0 5 up to 0 2 Cure Speed Fast Fast Medium Slow Fast Optional Primer 7649 7471 7471 7649 7471 7471 Colour Yellow Green Green Silver Green Viscosity c P 525 125 1800 250 000 1 250 Liquid Liquid Liquid Poste Liquid WHEN TO USE PRIMERS Primers are used when the surfaces to be threadlocked and sealed are not active enough to cause curing to take place or when the cure is required to be accelerated The table below shows common materials and when to use primer Select the correct primer from the table ACTIVE SURFACE PRIMER NOT REQUIRED INACTIVE SURFACE PRIMER REQUIRED Brass Copper Aluminium Black Oxide Bronze Iron Stoinless Steel Anodised Magnesium Passivated Surfaces Zinc Titanium Nickel CHARCTERISTICS ADVANTAGES OF RETAINING COMPOUND Retaining compound flows into all voids between mating parts retaining and sealing Can double press fit strengths steel to steel Slip fits can exceed heavy press shrink strength steel to steel
19. INTENANCE PRODUCTS THREADLOCKING Into Hole Clean all threads bolt and hole with Loctite ODC Free Cleaner amp Degreaser N If necessary spray all threads with Primer Refer to Technical Data Allow to dry Co Squirt several drops Loctite 262 Threadlocker down the sides of the female threads Avoid touching bottle tip to metal Note Use 277 Threadlocker if stud is over 25mm diameter Apply several drops 262 Threadlocker onto stud threads Install studs Position cover head etc Apply drops of Loctite 243 Threadlocker onto exposed threads Log Tighten nuts as required Worldwide or Application Specific Alternative HIGH STRENGTH DISASSEMBLY Localized Heating Methods 1 Apply localized heat to nut or stud 230 C for 5 minutes 2 Disassemble while HOT Note Use standard hand tools for disassembly of low and medium strength Threadlockers A LOCTITE MAINTENANCE PRODUCTS THREADLOCKING Not Here Clean bolts and nuts with Loctite ODC Free Cleaner amp Degreaser Assemble components Tighten nuts Apply drops of Loctite 290 Threadlocker at the nut and bolt juncture WN p Avoid touching bottle tip to metal Note For preventive maintenance on existing equipment RETIGHTEN nuts and apply Loctite 290 Threadlocker at the nut and bolt juncture ADJUSTMENT SCREWS gt o Adjust screw to proper settin
20. NEW WELDS PREVENTATIVE MAINTENANCE 1 Remove all slag and scale while hot 2 Apply sealant when weld is 50 and cooling down 3 Follow information above LOCTITE MAINTENANCE PRODUCTS FORM IN PLACE GASKETING Continuous Bead Flat Flange Raised Flange 1 Remove old gasketing material and other heavy contaminants with Loctite CHISEL Gasket Remover Use mechanical removal technique if required Note Avoid grinding 2 Clean both flanges with Loctite ODC Free Cleaner amp Degreaser 3 Spray Loctite Primer Refer Technical Data on only one surface Allow to dry 4 Apply a continuous bead of SELECTED LOCTITE GASKETING PRODUCT to the other surface Note Circle all bolt holes with sealant if appropriate 5 Mate Parts Assemble and tighten as required Note Immediate assembly not required however avoid delays over 45 minutes 6 Allow to cure a No pressure immediate service b Low pressure up to 3 45MPa 30 to 45 minutes c High pressure 3 45 to 17 2MPa 4 hours d Extreme high pressure 17 2 to 34 45MPa 24 hours LOCTITE GASKETING QUICK SELECTOR Gap Temp Use Product Fill Range FLANGE SEALANT MASTER GASKET General FLANGE SEALANT 518 0 5mm 55 C to 150 General MASTER GASKET 515 0 5mm 55 C to 150 Hi Temp GASKET ELIMINATOR 510 0 25mm 55 C to 200 C LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS GASKET DRESSING SEALED FLANGES WITH GASKET
21. NTENANCE PRODUCTS SHAFT MOUNTED COMPONENTS Bearing BEARING MOUNT 641 OR QUICK METAL 660 ORIGINAL 1 Machine shaft to 0 05mm radial slip fit with 50 80 rms finish second cut 2 Clean all parts with Loctite ODC Free Cleaner amp Degreaser Co Spray all parts I D and O D with Loctite Primer Refer Technical Dota Apply Loctite 641 dabs around shaft at engagement area Assemble parts Do not rotate Wipe off excess O Q b Allow ten minutes cure time prior to service WORN SHAFT Follow directions above except 1 Determine radial gap 2 If radial gap exceeds 0 1mm Loctite Primer must be used 3 Take steps to maintain concentricity with large gaps 4 Larger gaps require longer cure times 30 60 minutes 5 Loctite QUICK METAL 660 is NOT recommended for radial gaps exceeding 0 5mm 6 See procedure for BADLY WORN SHAFT page 24 Note Loctite QUICK METAL 660 is very fast fixturing 30 seconds or less with Loctite 7471 Primer T LOCTITE MAINTENANCE PRODUCTS SHAFT MOUNTED COMPONENTS e Bearing 620 or 680 or QUICK METAL 660 Shaft ORIGINAL Machine shaft to 0 05mm radial slip fit with 50 80 rms finish second cut Clean all parts with Loctite ODC Free Cleaner amp Degreaser Do NOT use Loctite Primer Apply a Loctite 680 coating around shaft and engagement area Avoid touching bottle tip to metal Assemble parts with rotating motion Wipe off
22. SEMBLIES N m gt 4 243 dab here 609 or 680 _ ker Coating Here ASSEMBLY Clean all parts with Loctite ODC Free Cleaner amp Degreqser Apply a 609 or 680 coating around shaft into keywoy and on key Avoid touching bottle tip to metal Assemble parts Wipe off excess Apply a 243 dab to screw Tighten set screw Allow 30 minutes cure time prior to service Note If gap exceeds 0 1mm use Loctite 7471 Primer on appropriate area shaft or keyway LOCTITE 609 and 680 are NOT recommended for radial gaps exceeding 0 2mm on shaft or keyway See BADLY WALLOWED KEYWAY for procedure page 23 i DISASSEMBYA 1 2 3 Tap component and key with hammer If necessary apply localized heat 230 C for five minutes Pull while hot LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS STRENGTHEN KEYED ASSEMBLIES QUICK METAL 660 Coated Keyway QUICK METAL 660 Coated Shim Determine the gap width on each side of key Select and trim appropriate shim stock Clean all parts with Loctite ODC Free Cleaner amp Degreaser WON If necessary spray all parts with Loctite 7471 Primer T Allow to dry Apply a Loctite QUICK METAL 660 coating into keyway Install shims Assemble as required using QUICK METAL 660 Allow 30 60 minute cure time O Note Minimise gap by using shim stock QUICK METAL 660 is NOT recomm
23. ck into the original container NEVER add solvents to Loctite Extend Spray application is recommended for larger areas Airless spray equipment is faster and provides more effective conversion due to improved surface penetration Conventional air spray equipment may be used but Loctite Extend may require thinning up to 1096 with water for proper spraying LOCTITE MAINTENANCE PRODUCTS CLEANING Loctite ODC Free Cleaner amp Degreaser is a non aqueous hybrocarbon based non CFC solvent designed for cleaning and degreasing of surfaces to be bonded with adhesives TYPICAL APPLICATIONS Used as a final pre assembly cleaning treatment to remove most greases oils lubrication fluids metal cuttings and fines for all surfaces to be bonded with adhesives It is designed to be used as a spray or in immersion cleaning processes at room temperature or heated HAND CLEANING For fast effective hand cleaning without skin irritating petroleum solvents use YUK OFF ORANGE Natural Citrus Hand Cleaner YUK OFF ORANGE Hand Cleaner removes grease grime paint oil and ink and contains aloe and lanolin to keep hands from cracking and drying out It s even biodegradable LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS MAKING 0 RINGS Cut rubber cord stock to length in fixture Apply Loctite Prism Adhesive 406 to Press cord ends together for 30 supplied in Loctite O Ring Splicing Kit end of co
24. ded On lightly rusted steel that has been wirebrushed the first coat will start to develop a violet color within 60 seconds This will become satin to flat black in appearance The second coat should dry to a satin black appearance On heavily rusted steel that has been wirebrushed the first coat should develop a purple black color within seconds The second coat should dry to a black color with gloss varying from flat to satin The second coat should be applied within 15 30 minutes of the first coat Note May cause staining of surrounding painted finishes APPLICATION CONDITIONS Loctite Extend may be applied when surface and air is between 10 minimum and 32 maximum Reaction is slower at lower temperatures If temperature is too hot film may surface dry and bubble High humidity is beneficial it slows drying but assists rust conversion Extend should not be applied in conditions of condensing humidity e g fog dew on ice in rain or in heavy sea salt spray atmospheres Steel surface may be damp but not wet i e continuous visible film of water DO NOT APPLY LOCTITE EXTEND TO SURFACES IN DIRECT SUNLIGHT APPLICATION EQUIPMENT METHODS Loctite Extend may be applied by brush roller or spray Brush or roller is suitable for small areas Avoid sags and ridges and keep edges wet by coating about a square yard at a time Roll away from previously coated area then roll back Do not pour unused material ba
25. e instructions Use the minimum amount of adhesive to one part only Apply activator if required to other part Avoid jiggling mated parts Apply clamp pressure if possible Allow maximum cure time possible See technical data for recommended cure times V QUESTIONS Call Loctite Technical Information See back cover for the Loctite Technical Information number in your area BE LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS BONDING TYPES OF JOINTS LAP OVERLAP JOGGLE LAP BUTT GOOD GOOD FAIR POOR 1 L 1 SCARF SINGLE STRAP DOUBLE STRAP FAIR GOOD BEST TYPES OF STRESSES TENSILE COMPRESSIVE CLEAVAGE FAIR GOOD POOR eD SHEAR PEEL GOOD POOR DESIGN GUIDELINES 1 Moximize sheor minimize cleavoge 2 Maximize compression minimize tensile 3 Joint width more important than overlap o LOCTITE MAINTENANCE PRODUCTS PRODUCT ADHESIVE QUICK SELECTOR TYPICAL APPLICATIONS 401 A general purpose Instant Adhesive Metal plastic rubber cork wood paper leather etc 406 A low viscosity Instant Adhesive ideal for difficult to bond surfaces Plastic rubber metal etc 454 A no run no drip Gel Instant Adhesive suitable for bonding porous materials Metal plastic rubber cork wood paper leather etc 480 A high impact high shear strength toughened Instant adhesive Metal most rubbers plastics
26. e or when the cure is required to be accelerated The table below shows common materials and when to use primer Select the correct primer from the table ACTIVE SURFACE PRIMER NOT REQUIRED INACTIVE SURFACE PRIMER REQUIRED Brass Copper Aluminium Black Oxide Bronze Iron Stoinless Steel Anodised Magnesium Passivated Surfaces Zinc Titanium Nickel CHARCTERISTICS ADVANTAGES OF GASKETING Form in place gasketing resists compression set Form in place gasketing fills all voids eliminating gaps Form in place gasketing provides a universal fit and is always in stock Form in place gasketing provides on site applications and saves you time Form in place gasketing is easy to clean up IMPORTANT NOTE Do not use anaerobic flange sealants on most thermoplastics ABS PVC etc Softening and or stress cracking may occur Anaerobic flange sealants can be used with 7649 Primer on Nylon and thermoset plastics LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS FORM IN PLACE GASKETING 1 Remove old gasketing material and other heavy contaminants with Loctite CHISEL Gasket Remover 2 Clean both flanges with Loctite ODC Free Cleaner amp Degreaser 3 Apply a continuous bead of the selected Loctite MAXX SILICONE to sealing surface Circle all bolt holes Note Use proper bead diameter to seal flange width and depth Minimize excessive material squeeze in 4 Assemble
27. ended for lateral gaps exceeding 0 5mm Higher strengths are obtained by NOT using 7471 Primer T with small 0 05mm 0 1mm gap and allowing longer cure 4 24 hours EMERGENCY REPAIR ONLY Due to the nature of the damage this should be considered a temporary repair until the unit can be replaced LOCTITE MAINTENANCE PRODUCTS SHAFT MOUNTED COMPONENTS OV QV duc NI a po ow Bearing 641 Sleeve 680 or QUICK METAL 660 Shaft Determine a minimum radial gap Select and trim appropriate sleeve to allow component slip fit Roughen sleeve O D with emery cloth Clean all parts with Loctite ODC Free Cleaner amp Degreaser Spray all parts with Primer Refer Technical Data Allow to dry Apply a Loctite 680 or Loctite QUICK METAL 660 coating around the shaft Avoid touching bottle tip to metal Install sleeve Apply a coating of Loctite 641 to sleeve O D Install component as required onto sleeved shaft Allow 30 60 minute cure time Note Minimize gap fill using shim stock or sleeve material QUICK METAL 660 is NOT recommended for radial gaps exceeding 0 5mm Higher strengths are obtained by NOT using Primer with small radial 0 05mm 0 1mm gap and allowing longer cure 4 24 hours EMERGENCY REPAIR ONLY Due to the nature of the damage this should be considered a temporary repair until the unit can be replaced E LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAI
28. equately cleaned prior to applying adhesive Note If adhesive failure is cured residue on one or both parts If one part is bare check that part for contamination 6 Were proper assembly techniques utilized 7 Was adhesive sealant allowed adequate cure time prior to service 8 Do assembly part conditions exceed capability of the adhesive sealant a excessive gaps c improper joint design b component materials d inadequate clamping fixturing 9 If additional assistance is required please call our HENKEL LOCTITE TECHNICAL INFORMATION LINE See back cover for the Loctite Technical Information number in your area LIMITATION OF WARRANTY The data contained herein are furnished for ANY KIND INCLUDING LOST PROFITS The discussion information only and are believed to be reliable We herein of various processes or compositions is not to cannot assume responsibility for the results obtained be interpreted as representation that they are free by others over whose methods we have no control from domination of patents owned by others or as a It is the user s responsibility to determine suitability license under any Henkel patents which may cover for the user s purpose of any production methods such processes or compositions We recommend that mentioned herein and to adopt such precautions as each prospective user test the proposed application may be advisable for the protection of property and to determine its suitability for the purpos
29. equired A LOCTITE MAINTENANCE PRODUCTS THREADLOCKING LOCTITE THREADLOCKER QUICK SELECTOR Use Strength Product Color Small Screws Low 222 Purple Nuts amp Bolts Medium 243 Blue Pre Assembled Medium 290 Green Nuts amp Bolts High 262 Red Studs up to 25mm High 262 Red Studs over 25mm High 277 Red WHY USE A PRIMER Primers activate inactive surfaces Primers speed cure times for faster return to service Primers speed curing through larger gaps and deep threads Primers substantially speed cure times on cold parts Eo de Primers act as cleaning agents Active surfaces Primer optional Brass copper bronze iron soft steel nickel Inactive surfaces Primer required Aluminium stainless steel magnesium zinc black oxide cadmium titanium others PREVENTING FASTENER SEIZURE ANTI SEIZE LOCTITE ANTI SEIZE QUICK SELECTOR Type Max Temp Heavy Duty 1315 C General purpose stainless steel compatible lead copper and sulphur free Silver Grade 870 C General purpose heavy duty high temperature grade Nickel 760 C Marine applications highly chemical resistant copper free Anti Seize compounds protect mated metal parts against friction galling and corrosion Anti Seize also reduces wrench torque to facilitate assembly and disassembly of threaded connections f H LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS THREADLOCKING PRODUCT Size of Thread 2
30. es intended of persons against any hazards that may be involved prior to incorporating any product or application in the handling and use thereof in its manufacturing process using this data as a In light of the foregoing HENKEL AUSTRALIA PTY guide Some products may be covered by one or LTD SPECIFICALLY DISCLAIMS ALL WARRANTIES OF more United States or foreign patents or patent MERCHANTABILITY OR FITNESS FOR A PARTICULAR applications PURPOSE ARISING FROM SALE OR USE OF ANY PRODUCTS HEREIN HENKEL AUSTRALIA PTY LTD SPECIFICALLY DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OF
31. excess Allow 2 hours minimum cure time prior to service WORN SHAFT Follow directions above except Qu UE Determine radial gap If radial gap exceeds 0 1mm Loctite Primer must be used Take steps to maintain concentricity with large gaps Larger gaps require longer cure times 30 60 minutes QUICK METAL 660 is NOT recommended for radial gaps exceeding 0 5mm See procedure for BADLY WORN SHAFT page 24 MAXIMUM TEMPERATURE 200 C continuous Same as above except use Loctite 620 with Loctite Primer DISASSEMBLY Pull as usual If necessary apply localized heat 230 C for 5 minutes Pull while hot EE LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS SHAFT MOUNTED COMPONENTS Bearing 609 Shaft STANDARD 1 Clean shaft O D and Component I D with ODC Free Cleaner Do NOT use Primer Apply a bead of Loctite 609 to circumference of shaft and bearing at leading edge of insertion or leading area of engagement Avoid touching bottle tip to metal Note Retaining compound will always be squeezed to the outside when applied to shaft N Do NOT use with Loctite Anti Seize or similar product 3 Press on as usuql Wipe off excess 4 No cure time required Note 609 is used due to low viscosity and wetting properties TANDEM MOUNT 1 Apply retaining compound to bore of inside component 2 Continue assembly as above A LOCTITE MAINTENANCE PRODUCTS
32. g Plunger Z N Apply drops of Loctite 290 Threadlocker at screw and body juncture Co Avoid touching bottle tip to metal Note If re adjustment is difficult apply heat to screw with soldering gun 230 C Use Loctite 222 when low strength locking is required LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS THREADLOCKING STRIPPED THREAD REPAIR Cleaned Bolt Release Agent Cover Threqdlocker Plate Stripped Release Agent Threads FORM A THREAD FORM A Half Fill Only THREAD t h Tape t Tape U New Threads Step 1 Step 2 Step 3 STANDARD THREAD REPAIR 1 Follow instructions on Loctite FORM A THREAD package 2 If cover plate is used for bolt alignment a Apply release agent to mating faces around repair area b Use waxed paper or similar film between faces 3 A jiggling twisting motion when initially inserting bolt improves threadconformation Note NOT intended for engine stud repair SMALL HOLE FINE THREAD REPAIR OPTION 1 Drill out damaged hole to oversize then follow STANDARD THREAD REPAIR OPTION 2 Apply FORM A THREAD to screw and insert into damage hole Clamp in place while product cures STUD INSTALLATION PERMANENT LIGHT DUTY Use stud or cut all thread to desired length Do NOT apply release agent to stud Proceed as STANDARD THREAD REPAIR Allow 30 minutes to cure Q N Assemble as r
33. irections Apply a thin layer of 5 Minute Epoxy to roughened area Immediately position disc patch over hole Apply a cover layer of Five Minute Epoxy over disc patch and Epoxy layer 1 Allow to cure before service use a Liquid storage 1 hour b Low pressure under 1000kPa 1 hour c High Pressure Not Recommended over 1000kPa Paint as required SEALING CRACKS Drill termination holes to prevent further cracking Follow directions above Modify as needed SEALING PINHOLES Follow directions above No disc patch needed us LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS POROSITY SEALING 290 Weld Bead lt Tank Wall Weld Porosity 1 IMPORTANT TAKE PROPER SAFETY PRECAUTIONS WHEN WORKING WITH FLAMMABLE LIQUID TANKS AVOID USE WITH COMPRESSIBLE GASSES Wire brush to remove paint rust etc from repair area Clean repair area with Loctite ODC Free Cleaner amp Degreaser Apply localized heat to bring repair area to approx 120 C Allow repair area to cool to approx 50 C So ehe Brush or spray 290 on repair area Note Not recommended for blowholes e Maximum porosity sealed 0 1mm 7 Allow to cure for 30 minutes for high pressure above 1000kPa allow a minimum of 1 hour 8 Clean with Loctite ODC Free Cleaner amp Degreaser to remove excess sealant Do not grind 9 Paint as required Note Casting repair uses same procedure SEALING
34. o Water Systems 69 69MPa 130 C 10 000 PSI 10 000 PSI DO NOT USE THESE PRODUCTS ON OXYGEN OR STRONG OXIDIZERS FLUID COMPATIBILITY QUESTIONS 1 Refer to Fluid Compatibility Chart inside 567 brochure 2 Contact your local Industrial Distributor 3 Call Loctite Technical Information See back cover for the Loctite Technical Information number in your area ES LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS THREADSEALING PRODUCT 569 567 577 HYDRAULIC MASTER PIPE HIGH PRESSURE SEALANT SEALANT PIPE SEALANT Size of Thread up to 3 4 up to 3 up to 3 up to 6 Strength Low Low Medium Low Breakaway Prevail 4 2 1 7 NA 11 6 NA Torque N m on MIO 55 to 150 55 to 205 55 to 150 55 to 130 Cure Speed Medium Slow Medium Instant Optional Primer 7471 7649 7649 NA Colour Format Brown Liquid White Gel Yellow Gel White Cord Visocisty c P 400 540 000 24 000 NA IMPORTANT PRODUCTS ARE NOT TO BE USED ON OXYGEN SYSTEMS OR IN OXYGEN RICH ENVIRONMENTS DO NOT USE WITH STRONG OXIDISERS CHLORINE Check compqatibility chort for fluid and gas compatibility WHEN TO USE PRIMERS Primers are used when the surfaces to be threadlocked and sealed are not active enough to cause curing to take place or when the cure is required to be accelerated The table below shows common materials and when to use primer Select the correct primer from the table
35. rd diameter seconds in groove of fixture O Ring is now ready to use MAKE THAT O RING THE RIGHT WAY Clean razor blade Use guillotine cutter for best square end cuts Keep cut ends clean no oily fingerprints Use one drop instant adhesive on one end only Use v groove jig for proper ailgnment and hold for 30 seconds Use waterproofing solution to protect the joint Os Uie ONS IMPORTANT NOTES 1 Recommended for static stationary O Rings only 2 Works best with nitrile rubber Buna N cord stock 3 On silicone stock use Loctite Primer 770 with Loctite Adhesive 406 LOCTITE MAINTENANCE PRODUCTS ORDERING CATEGORY SIZE ITEM NO THREADLOCKERS 222 SMALL SCREW 10 ml bottle 22220 50 ml bottle 22250 250 ml bottle 22270 243 REMOVABLE 10 ml bottle 21320 50 ml bottle 21321 250 ml bottle 21322 262 PERMANENT 10 ml bottle 26220 50 ml bottle 26250 250 ml bottle 26270 277 LARGE STUD 50 ml bottle 27750 250 ml bottle 27770 290 WICKING 10 ml bottle 29020 50 ml bottle 29050 250 ml bottle 29070 THREAD SEALANTS 569 HYDRAULIC PNEUMATIC SEALANT 50 ml bottle 56950 250 ml tube 56970 567 MASTER PIPE SEALANT 50 ml tube 56747A 250 ml tube 56741 577 UNIVERSAL PIPE SEALANT 50 ml tube 19259 250 ml tube 34112 55 PIPE SEALANT CORD 150m 31899 50m 37371 RETAINING COMPOUNDS 609 GENERAL PURPOSE 10 ml bottle 30013 50 ml bottle 30015 250 ml bottle 30014 620 HIGH TEMPERATURE 50 ml bottle 62050 250 ml bottle 62070 660 QUICK
36. s and sealants representative at the telephone number listed on the back cover of this guide THREADLOCKING THROUGH HOLES BOLTS AND NUTS PAGE 4 BLIND HOLES 4 5 STUDS 5 HIGH STRENGTH DISASSEMBLY 5 PRE ASSEMBLED FASTENERS 6 ADJUSTMENT SCREWS 6 STRIPPED THREAD REPAIR 7 THREADLOCKER QUICK SELECTOR 8 PREVENTING FASTENER SEIZURE ANTI SEIZE 8 WHY USE PRIMERS 8 THREADLOCKING TECHNICAL DATA 9 THREAD SEALING STANDARD FITTINGS 10 PIPE UNIONS 10 COMPRESSION FITTINGS 11 FLARED SWAGED FITTINGS 11 HOSE ENDS 12 THREAD SEALING QUICK SELECTOR 12 THREAD SEALING TECHNICAL DATA 13 LOCTITE DO IT RIGHT USERS GUIDE LOCTITE MAINTENANCE PRODUCTS CONTENTS Ea PUNCTURE SEALING TANKS VESSELS ETC 14 POROSITY SEALINGS EXISTING WELDS 15 NEW WELDS 15 CASTINGS 15 FORM IN PLACE GASKETING SEALING CAST RIGID FLANGES 16 GASKETING QUICK SELECTOR 16 GASKET DRESSING SEALED FLANGES 17 FLANGE SEALING TECHNICAL DATA 18 FORM IN PLACE GASKETING STAMPED OR SHEET METAL FLANGES 19 SILICONE QUICK SELECTOR 20 MAXX VS STANDARD SILICONES 20 KEYED ASSEMBLIES STANDARD DUTY 21 HEAVY DUTY 22 REPAIRING BADLY WALLOWED KEYWAYS 23 SHAFT MOUNTED ASSEMBLIES REPAIRING BADLY WORN SHAFTS 24 SLIP FIT LIGHT DUTY 25 SLIP FIT HEAVY DUTY 26 PRESS FIT 27 HOUSED COMPONENTS SLIP FIT LIGHT DUTY 28 SLIP FIT HEAVY DUTY 29 RETAINING LARGE GAPS 30 SEALING RETAINING METALLIC SEALS 31 RETAINING COMPOUNDS QUICK SELECTOR 32 RETAINING TECHNICAL
Download Pdf Manuals
Related Search