Home

HP Mini 200

1. Computer major components 17 18 Item Component Spare part number Broadcom 4313GN 802 11b g n 1x1 WiFi and 20702 Bluetooth 4 0 657325 001 Combo Adapter Ralink RT5390R 802 11bgn 1x1 Wi Fi Adapter 691415 001 Intel Centrino Advanced N 6230 WLAN module 631956 001 Ralink 5390GN 802 11b g n 1x1 WiFi Adapter 630703 001 15 Hard drive 2 5 in 7 0 mm SATA does not include hard drive bracket hard drive connector cable hard drive rubber isolators screws 500 GB 5400 rpm 634932 001 320 GB 5400 rpm 645193 001 250 GB 5400 rpm 645191 001 Hard Drive Hardware Kit not illustrated includes hard drive bracket hard drive 664913 001 connector cable hard drive rubber isolators and screws 16 Service cover 663676 001 17 Corner covers 652308 001 Rubber Kit includes 2 rubber feet 650734 001 Chapter 3 Illustrated parts catalog Display assembly subcomponents Item Component Spare part number 1 Display bezel 658503 001 2 Webcam microphone module 658516 001 3 10 1 in LED BrightView WSVGA display panel 658511 001 4 Display Hinge Kit includes left and right display hinges and brackets 650711 001 5 Display Cable Kit includes display panel cable and webcamera microphone 658505 001 module cable 6 Antenna Kit includes left and right wireless antenna cables and transceivers 658498 001 7 Display enclosure In gloss black finish 658499 001 In Pacific blue finish 658502
2. 60 Heat sink Description Spare part number Heat sink includes replacement thermal material 651898 001 Before removing the heat sink follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 and then remove the following components Service cover see WLAN module on page 36 Keyboard see Keyboard on page 45 Top cover see Top cover on page 48 System board see System board on page 55 Fan see Fan on page 58 Remove the heat sink 1 Remove the two Phillips PM2 0x4 6 screws 1 that secure the heat sink to the system board Chapter 4 Removal and replacement procedures 2 Remove the heat sink 2 NOTE Due to the adhesive quality of the thermal material located between the heat sink and system board components it may be necessary to move the heat sink from side to side to detach it The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system board components each time the heat sink is removed Replacement thermal material is included with the heat sink and system bo
3. New Zealand SANZ 1 Norway NEMKO 1 The People s Republic of China CCC 4 Saudi Arabia SASO 7 Singapore PSB 1 South Africa SABS 1 South Korea KTL 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 6 Thailand TISI 1 The United Kingdom ASTA 1 Chapter 8 Power cord set requirements Country region Accredited agency Applicable note number The United States UL 2 1 The flexible cord must be Type HO5VV F 3 conductor 0 75 mm conductor size Power cord set fittings appliance coupler and wall plug must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used The flexible cord must be Type SVT SJT or equivalent No 18 AWG 3 conductor The wall plug must be a two pole grounding type with a NEMA 5 15P 15 A 125 V or NEMA 6 15P 15 A 250 V ac configuration CSA or C UL mark UL file number must be on each element The appliance coupler flexible cord and wall plug must bear a T mark and registration number in accordance with the Japanese Dentori Law The flexible cord must be Type VCTF 3 conductor 0 75 mm or 1 25 mm conductor size The wall plug must be a two pole grounding type with a Japanese Industrial Standard C8303 7 A 125 V ac configuration The flexible cord must be Type RVV 3 conductor 0 75 mm conductor size Power cord set fittings appliance coupler and wall plug must bear the CCC certification mark The flexible cord must be Type HO5VV F 3X0 75 mm
4. WLAN antennas 2 Send and receive wireless signals to communicate with WLANs 2 WWAN antennas 2 Send and receive wireless signals to communicate with WWANS 3 Internal microphone Records sound 4 Webcam Records video and captures still photographs To use the webcam double click the ArcSoft Camera Suite icon on the desktop or select Start gt All Programs gt ArcSoft Camera Suite gt Launch WebCam Companion 5 Webcam light On The webcam is in use The antennas are not visible from the outside of the computer For optimal transmission keep the areas immediately around the antennas free from obstructions To see wireless regulatory notices refer to the section of the Regulatory Safety and Environmental Notices that applies to your country or region These notices are located in Help and Support 6 Chapter 2 External component identification Buttons Item a 2 Component Power button Web browser button Description e When the computer is off press the button to turn on the computer e When the computer is on press the button briefly to initiate Sleep e When the computer is in the Sleep state press the button briefly to exit Sleep e When the computer is in Hibernation press the button briefly to exit Hibernation If the computer has stopped responding and Windows shutdown procedures are ineffective press and hold the power button for at least 5 seconds to turn o
5. 001 Display assembly subcomponents 19 Item Component Spare part number In Sonoma red 658500 001 In gloss black finish for use only on computer models equipped with WWAN 684439 001 capobility 20 Chapter 3 Illustrated parts catalog Mass storage devices Item Component Spare part number 1 Hard drive 2 5 in 7 0 mm SATA does not include hard drive connector cable hard drive bracket or screws 500 GB 5400 rpm 634932 001 320 GB 5400 rpm 645193 001 250 GB 5400 rpm 645191 001 Hard Drive Hardware Kit includes 6649 13 001 2a Hard drive bracket 2b Hard drive connector cable 2c Hard drive rubber isolators 2 Screws not illustrated 3 USB external DVD RW DL SuperMulti Drive 659940 001 Mass storage devices 21 Miscellaneous parts Component Spare part number 40 W HP Smart AC adapter RC V 2 wire 624502 001 HP mobile optical wireless 2 4 GHz mouse 597587 001 Power cord 3 pin black 1 83 m For use in Argentina 490371 D01 For use in Australia 490371 011 For use in Denmark 490371 081 For use in Europe 490371 021 For use in India 49037 1 D61 For use in Israel 49037 1 BB1 For use in Italy 49037 1 061 For use in Japan 490371 291 For use in North America 490371 001 For use in the People s Republic of China 49037 1 AAT1 For use in South Africa 49037 ART For use in South Korea 49037 1 ADI1 For use in Switzerland 490371 111
6. 36 Remove the memory module 1 Spread the retaining tabs 1 on each side of the memory module slot to release the memory module The memory module tilts up 2 Remove the memory module 2 by pulling it away from the slot at an angle Reverse this procedure to install the memory module Component replacement procedures 41 RTC battery Description Spare part number RTC battery 621565 001 Before removing the RTC battery follow these steps 1 4 5 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system Disconnect all external devices connected to the computer Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer Remove the battery see Battery on page 34 Remove the service cover see WLAN module on page 36 Remove the RTC battery 1 2 Insert a non conductive flattip tool 1 into the notch 2 on the side of the RTC battery socket Remove the RTC battery 3 from the socket on the system board Reverse this procedure to install the RTC battery When installing the RTC battery be sure the sign faces up 42 Chapter 4 Removal and replacement procedures Hard drive E NOTE The hard drive spare part kit does not include the hard drive bracket connector cable rubber isolator
7. AC The 3 conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used Requirements for all countries The following requirements are applicable to all countries and regions The length of the power cord set must be at least 1 5 m 5 0 ft and no more than 2 0 m 6 5 ft All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country or region where the power cord set will be used The power cord sets must have a minimum current capacity of 10 A and a nominal voltage rating of 125 or 250 V ac as required by the power system of each country or region The appliance coupler must meet the mechanical configuration of an EN 60 320 IEC 320 Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer Requirements for all countries 81 Requirements for specific countries and regions 82 Country region Accredited agency Applicable note number Argentina IRAM 1 Australia SAA 1 Austria OVE 1 Belgium CEBEC 1 Brazil ABNT Canada CSA 2 Chile IMQ Denmark DEMKO Finland FIMKO France UTE 1 Germany VDE 1 India ISI 1 Israel SII 1 Italy IMQ 1 Japan JIS 3 The Netherlands KEMA 1
8. Memory module on page 41 e Power connector cable see System board on page 55 e Fan see Fan on page 58 e Heat sink see Heat sink on page 60 Component replacement procedures 55 Remove the system board 1 Remove the two Phillips PM2 0x5 7 screws that secure the system board to the base enclosure 2 Release the power connector 1 from the clip built into the base enclosure 3 Flex the right side of the base enclosure 2 until the jacks and ports on the right side of the system board are clear of the openings in the base enclosure 4 Liftthe right side of the system board 3 until it rests at an angle 56 Chapter 4 Removal and replacement procedures 5 Remove the system board 4 by sliding it up and to the right at an angle 27 NOTE lf it is necessary to replace the power connector cable turn the system board upside down with the rear toward you and then disconnect the power connector cable from the system board The power connector cable is available using spare part number 656095 001 Reverse this procedure to install the system board and the power connector cable Component replacement procedures 57 Fan Description Spare part number Fan 651897 001 E NOTE To properly ventilate the computer allow at least 7 6 cm 3 in of clearance on the left side of the computer The computer uses an electric fan for ventilation The fan is controlled by a temperature sensor and is designed
9. Wh 2 55 Ah Li ion battery 646757 001 6 cell 55 Wh 2 55 Ah Li ion battery 650711 001 Display hinges includes left and right display hinges 650734 001 Rubber Kit includes 2 base enclosure rubber feet 650735 001 Screw Kit 650736 001 Speakers includes left and right speakers and cables 651897 001 Fan 651898 001 Heat sink includes replacement thermal material 652308 001 Corner covers includes left and right corner covers 652972 001 2 GB memory module PC3 12800 1600 MHz 655795 001 Atheros 9485GN 802 11b g n 1x1 WiFi and 3012 Bluetooth 4 0 Combo Adapter 656095 001 Power connector cable 657325 001 Broadcom 4313GN 802 11b g n 1x1 WiFi and 20702 Bluetooth 4 0 Combo Adapter 658498 001 Antenna Kit includes WLAN antenna cables and transceivers and WWAN antenna cables and transceivers 658499 001 Display enclosure in gloss black finish 658500 001 Display enclosure in Sonoma red finish 658502 001 Display enclosure in Pacific blue finish 658503 001 Display bezel 658505 001 Display panel cable includes display panel cable and webcamera microphone module cable 658507 001 10 1 in BrightView WSVGA display assembly in gloss black finish includes display panel cable webcamera microphone module and WLAN antenna cables and transceivers 658508 001 10 1 in BrightView WSVGA display assembly in Sonoma red finish includes display panel cable webcamera microphone module and WLAN antenna cables and transceivers 658510 001 10 1
10. area follow these steps a Identify the BIOS update that is later than the BIOS version currently installed on your computer Make a note of the date name or other identifier You may need this information to locate the update later after it has been downloaded to your hard drive b Follow the on screen instructions to download your selection to the hard drive Make a note of the path to the location on your hard drive where the BIOS update is downloaded You will need to access this path when you are ready to install the update Ey NOTE If you connect your computer to a network consult the network administrator before installing any software updates especially system BIOS updates Using Setup Utility 71 BIOS installation procedures vary Follow any instructions that are displayed on the screen after the download is complete If no instructions are displayed follow these steps 1 5 Windows 7 Open Windows Explorer by selecting Start gt Computer Windows XP Open Windows Explorer by selecting Start gt My Computer Double click your hard drive designation The hard drive designation is typically Local Disk C Using the hard drive path you recorded earlier open the folder on your hard drive that contains the update Double click the file that has an exe extension for example filename exe The BIOS installation begins Complete the installation by following the on screen instructions E NOTE Afte
11. conductor size KTL logo and individual approval number must be on each element Corset approval number and logo must be printed on a flag label The flexible cord must be Type HVCTF 3x1 25 mm conductor size Power cord set fittings appliance coupler cable and wall plug must bear the BSMI certification mark For 127 V ac the flexible cord must be Type SVT or SJT 3 x 18 AWG with plug NEMA 5 15P 15 A 125 V ac with UL and CSA or C UL marks For 240 V ac the flexible cord must be Type HO5VV F 3x0 75 1 00 mm conductor size with plug BS 1363 A with BSI or ASTA marks Requirements for specific countries and regions 83 9 Recycling When a non rechargeable or rechargeable battery has reached the end of its useful life do not dispose of the battery in general household waste Follow the local laws and regulations in your area for battery disposal HP encourages customers to recycle used electronic hardware HP original print cartridges and rechargeable batteries For more information about recycling programs see the HP Web site at http www hp com recycle 84 Chapter 9 Recycling Index A AC adapter spare part number 22 23 AC adapter battery light 10 Action keys 5 antenna locations 6 removal 66 spare partnumber 19 24 67 Antenna Kit spare part number 19 24 67 audio product description 2 audio in jack 11 audio out jack 11 B base enclosure spare part number 17 25 battery removal 34 spare part
12. gt Backup and Restore 2 Follow the on screen instructions to set up your backup create a system image select models only or create a system repair disc select models only Backing up your information 77 Performing a system recovery In case of system failure or instability the computer provides the following tools to recover yovr files e Windows recovery tools You can use Windows Backup and Restore to recover information you have previously backed up You can also use Windows Startup Repair to fix problems that might prevent Windows from starting correctly e 11 recovery tools You can use the f1 1 recovery tools to recover your original hard drive image The image includes the Windows operating system and software programs installed at the factory E NOTE If you are unable to boot start up your computer and you cannot use the system repair discs you previously created select models only you must purchase a Windows 7 operating system DVD to reboot the computer and repair the operating system For additional information refer to the Using a Windows 7 operating system DVD purchased separately section Using the Windows recovery tools To recover information you previously backed up 1 Select Start All Programs Maintenance Backup and Restore 2 Follow the on screen instructions to recover your system settings your computer select models only or your files To recover your information using St
13. or inserting a hard drive shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system Before handling a drive be sure that you are discharged of static electricity While handling a drive avoid touching the connector Before removing a diskette drive or optical drive be sure that a diskette or disc is not in the drive and be sure that the optical drive tray is closed Handle drives on surfaces covered with at least one inch of shock proof foam Avoid dropping drives from any height onto any surface After removing a hard drive an optical drive or a diskette drive place it in a static proof bag Avoid exposing an internal hard drive to products that have magnetic fields such as monitors or speakers Avoid exposing a drive to temperature extremes or liquids If a drive must be mailed place the drive in a bubble pack mailer or other suitable form of protective packaging and label the package FRAGILE Grounding guidelines Electrostatic discharge damage 28 Electronic components are sensitive to electrostatic discharge ESD Circuitry design and structure determine the degree of sensitivity Networks built into many integrated circuits provide some protection but in many cases ESD contains enough power to alter device parameters or melt silicon junctions A discharge of static electricity from a finger or other conducto
14. stripe Backlight LED Character display 80 x 25 Total power consumption 3 46W Viewing angle Chapter 6 Specifications 45 horizontal 15 35 vertical typical Hard drive specifications 500 GB 320 GB 250 GB Dimensions Height 9 5 mm 9 5 and 7 0 mm 9 5 and 7 0 mm Width 70 mm 70 mm 70 mm Weight 101g 101g 101g Interface type SATA SATA SATA Seek times typical read including setting Single track 3 ms 3 ms 3 ms Average read write 13 ms 13 ms 13 ms Maximum 24 ms 24 ms 24 ms Logical blocks 1 048 576 000 625 141 400 488 397 168 Disk rotational speed 5400 rpm 7200 and 7200 and 5400 rpm 5400 rpm Operating temperature O C to 60 C 32 F to 140 F 1 GB 1 billion bytes when referring to hard drive storage capacity Actual accessible capacity is less NOTE Certain restrictions and exclusions apply Contact technical support for details Hard drive specifications 75 76 7 Backup and recovery To protect your information use Windows Backup and Restore to back up individual files and folders back up your entire hard drive select models only create system repair discs select models only by using the installed optical drive select models only or an optional external optical drive or create system restore points In case of system failure you can use the backup files to restore the contents of your computer Windows Backup and Restore provides the following op
15. to start up boot the computer and repair the operating system in case of system instability or failure Your initial and subsequent backups allow you to restore your data and settings if a failure occurs You can back up your information to an optional external hard drive a network drive or discs Note the following when backing up Store personal files in the Documents library and back it up regularly e Back up templates that are stored in their associated programs e Save customized settings that appear in a window toolbar or menu bar by taking a screen shot of your settings The screen shot can be a time saver if you have to reset your preferences e When backing up to discs use any of the following types of discs purchased separately CD R CD RW DVD R DVD R DL DVD R DVD R DL or DVD RW The discs you use will depend on the type of external optical drive you are using Ey NOTE DVDs and DVDs with double layer DL support store more information than CDs so using them for backup reduces the number of recovery discs required e When backing up to discs number each disc before inserting it into the external drive To create a backup using Backup and Restore E NOTE Be sure that the computer is connected to AC power before you start the backup process NOTE The backup process may take over an hour depending on file size and the speed of the computer 1 Select Start gt All Programs gt Maintenance
16. 001 not WWAN capability 1 0 MB L2 cache dual core 6 5 W For use only on computer models equipped with an Intel Atom N2600 1 60 GHz processor and 676910 001 WWAN capobility 1 0 MB L2 cache dual core 3 5 W For use only on computer models equipped with an Intel Atom N2600 1 60 GHz processor but 676909 001 not WWAN capability 1 0 MB L2 cache dual core 3 5 W Before removing the system board follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 and then remove the following components e Service cover see WLAN module on page 36 e Hard drive see Hard drive on page 43 e Keyboard see Keyboard on page 45 e Top cover see Top cover on page 48 When replacing the system board be sure that the following components are removed from the defective system board and installed on the replacement system board e SIM see SIM select models only on page 35 e WLAN module see WLAN module on page 36 e WWAN module see WWAN module on page 39 e RTC battery see RTC battery on page 42 e Memory module see
17. 0x5 0 screws 2 that secure the top cover and the corner covers to the base enclosure Ey NOTE The rubber feet are notched differently The rubber foot 1 that fits on the left side has a rectangular alignment notch The rubber foot 2 that fits on the right side has an L shaped alignment notch When installing the rubber feet align them according to the side of the computer on which they should be installed 50 Chapter 4 Removal and replacement procedures 6 Remove the corner covers 7 Release the wireless antenna cables from the clips 1 and routing channel built into the base enclosure 8 Disconnect the display panel cable 2 from the system board Component replacement procedures 51 9 Remove the two Phillips PM2 0x5 0 screws that secure the top cover to the base enclosure 10 Turn the computer right side up with the front toward yov 11 Open the computer as far as it will open 12 Release the ZIF connector 1 to which the power button board cable is connected and then disconnect the power button board cable 2 from the system board 13 Disconnect the speaker cable 3 from the system board 52 Chapter 4 Removal and replacement procedures 14 Remove the five Phillips PM2 0x5 0 screws that secure the top cover to the base enclosure 15 Lift the front edge of the top cover 1 until the left and right sides disengage from the base enclosure 16 Remove the top cover 2 R
18. 1 RTC battery 612599 001 HP Ic2000 HSPA Mobile Broadband Module 612600 001 HP Ic2010 HSPA Mobile Broadband Module 621565 001 2 GB memory module PC3 10600 1333 MHz 624502 001 40 W HP Smart AC adapter RC V 2 wire 630703 001 Ralink 5390GN 802 11b g n 1x1 WiFi Adapter 632155 001 HP hs2340 HSPA Mobile Broadband Module 634932 001 500 GB 5400 rpm 7 0 mm hard drive does not include hard drive bracket hard drive connector cable hard drive rubber isolators or screws NOTE The hard drive bracket hard drive connector cable hard drive rubber isolators and screws are included in the Hard Drive Hardware Kit spare part number 664913 001 645191 001 250 GB 5400 rpm 7 0 mm hard drive does not include hard drive bracket hard drive connector cable hard drive rubber isolators or screws NOTE The hard drive bracket hard drive connector cable hard drive rubber isolators and screws are included in the Hard Drive Hardware Kit spare part number 664913 001 Sequential part number listing 23 24 Spare part number Description 645193 001 320 GB 5400 rpm 7 0 mm hard drive does not include hard drive bracket hard drive connector cable hard drive rubber isolators or screws NOTE The hard drive bracket hard drive connector cable hard drive rubber isolators and screws are included in the Hard Drive Hardware Kit spare part number 664913 001 646755 001 3 cell 28
19. 43 251 Keyboard for use in Russia includes keyboard cable 660843 281 Keyboard for use in Thailand includes keyboard cable 660843 291 Keyboard for use in Japan includes keyboard cable 660843 441 Keyboard for use in Belgium includes keyboard cable 660843 AB1 Keyboard for use in Taiwan includes keyboard cable 660843 AD1 Keyboard for use in South Korea includes keyboard cable 66084331 Keyboard for use in the Netherlands includes keyboard cable 660843 BA1 Keyboard for use in Slovenia includes keyboard cable 660843 BB1 Keyboard for use in Israel includes keyboard cable 660843 8G1 Keyboard for use in Switzerland includes keyboard cable 660843 D61 Keyboard for use in India includes keyboard cable 660843 DH1 Keyboard for use in Denmark Finland and Norway includes keyboard cable 660843 DJ1 Keyboard for use in Greece includes keyboard cable 660843411 Keyboard for use in the Czech Republic and Slovakia includes keyboard cable 663675 001 Base enclosure 663676 001 Service door 663677 001 Top cover in gloss black finish includes TouchPad board and bracket 664913 001 Hard Drive Hardware Kit includes hard drive bracket hard drive connector cable hard drive rubber isolators and screws 668166 001 10 l in BrightView WSVGA display assembly in gloss black for use only on computer models with WWAN capability includes display panel cable webcamera microphone module WLAN antenna cables and transceivers and WWAN anten
20. For use in Taiwan 49037 1 AB1 For use in Thailand 490371 201 For use in the United Kingdom and Singapore 490371 031 Screw Kit 650735 001 22 Chapter 3 Illustrated parts catalog Sequential part number listing Spare part number Description 49037 1 001 Power cord for use in North America 3 pin black 1 83 m 490371 011 Power cord for use in Australia 3 pin black 1 83 m 490371 021 Power cord for use in Europe 3 pin black 1 83 m 490371 031 Power cord for use in the United Kingdom and Singapore 3 pin black 1 83 m 490371 061 Power cord for use in Italy 3 pin black 1 83 m 490371 081 Power cord for use in Denmark 3 pin black 1 83 m 490371 111 Power cord for use in Switzerland 3 pin black 1 83 m 49037 1 201 Power cord for use in Thailand 3 pin black 1 83 m 490371 291 Power cord for use in Japan 3 pin black 1 83 m 490371 AA1 Power cord for use in the People s Republic of China 3 pin black 1 83 m 49037 1 AB1 Power cord for use in Taiwan 3 pin black 1 83 m 490371 AD1 Power cord for use in South Korea 3 pin black 1 83 m 49037 1 AR1 Power cord for use in South Africa 3 pin black 1 83 m 49037 1 BB1 Power cord for use in Israel 3 pin black 1 83 m 490371 D01 Power cord for use in Argentina 3 pin black 1 83 m 49037 1 D61 Power cord for use in India 3 pin black 1 83 m 597587 001 HP 2 4 GHz wireless optical mouse 599516 00
21. GY HP Mini 200 Maintenance and Service Guide Copyright 2012 Hewlett Packard Development Company L P Bluetooth is a trademark owned by its proprietor and used by Hewlett Packard Company under license Intel and Atom are trademarks or registered trademarks of Intel Corporation in the United States and other countries Microsoft and Windows are U S registered trademarks of Microsoft Corporation SD Logo is a trademark of its proprietor The information contained herein is subject to change without notice The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein First Edition May 2012 Document Part Number 696791 001 Safety warning notice N WARNING To reduce the possibility of heat related injuries or of overheating the device do not place the device directly on your lap or obstruct the device air vents Use the device only on a hard flat surface Do not allow another hard surface such as an adjoining optional printer or a soft surface such as pillows or rugs or clothing to block airflow Also do not allow the AC adapter to contact the skin or a soft surface such as pillows or rugs or clothing during operation The device and the AC adapter comply with the user accessible s
22. Reverse this procedure to install the WLAN module 38 Chapter 4 Removal and replacement procedures WWAN module Description Spare part number HP hs2350 HSPA Mobile Broadband Module 668969 001 HP hs2340 HSPA Mobile Broadband Module 632155 001 HP Ic2010 HSPA Mobile Broadband Module 612600 001 HP Ic2000 HSPA Mobile Broadband Module 612599 001 Z CAUTION To prevent an unresponsive system replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region If you replace the module and then receive a warning message remove the module to restore device functionality and then contact technical support Before removing the WWAN module follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 5 Remove the service cover see WLAN module on page 36 Remove the WWAN module 1 Disconnect the WWAN antenna cables 1 from the terminals on the WWAN module Ef NOTE The 1 WWAN antenna cable is connected to the WWAN module Main t
23. ard spare part kits y NOTE The following illustration shows the replacement thermal material locations Thermal paste is used on the processor 1 and the heat sink section 2 that services it Reverse this procedure to install the heat sink Component replacement procedures 61 Display assembly 62 E NOTE The display assembly spare part kit includes the display panel cable 2 WLAN antenna transceivers and cables and a webcamera microphone module and cable Description Spare part number In gloss black finish 658507 001 In Pacific blue finish 658510 001 In Sonoma red finish 658508 001 WSVGA HD display assembly in gloss black finish for use only on computer models equipped 668166 001 with WWAN capability includes WWAN antenna cables and transceivers Before removing the display assembly follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 and then remove the following components e Service cover see WLAN module on page 36 e Keyboard see Keyboard on page 45 e Top cover see Top cover on page 48 Remov
24. artup Repair follow these steps CAUTION Using Startup Repair completely erases hard drive contents and reformats the hard drive All files you have created and any software installed on the computer are permanently removed When reformatting is complete the recovery process restores the operating system as well as the drivers software and utilities from the backup used for recovery 1 If possible back up all personal files 2 If possible check for the presence of the Windows partition and the HP Recovery partition To check for the Windows partition select Start gt Computer To check for the HP Recovery partition click Start right click Computer click Manage and then click Disk Management f NOTE If the Windows partition and the HP Recovery partition are not listed you must recover your operating system and programs using the Windows 7 operating system DVD and the Driver Recovery disc both purchased separately For additional information refer to the Using a Windows 7 operating system DVD purchased separately section 3 If the Windows partition and the HP Recovery partition are listed restart the computer and then press f8 before the Windows operating system loads 4 Select Startup Repair 5 Follow the on screen instructions 78 Chapter 7 Backup and recovery Ey NOTE For additional information on recovering information using the Windows tools perform a Using search for these to
25. camera microphone module cable and is available in the Display Cable Kit spare part number 658505 001 9 If it is necessary to replace the wireless antenna cables and transceivers a Release the WLAN antenna transceivers 1 and the WWAN antenna transceivers 2 from the display enclosure The antenna transceivers are attached to the display enclosure with double sided tape 66 Chapter 4 Removal and replacement procedures b Release the wireless antenna cables from the clips 3 built into the display enclosure Remove the wireless antenna cables and transceivers The wireless antenna cables and transceivers are available in the Antenna Kit spare part number 658498 001 Reverse this procedure to reassemble and install the display assembly Component replacement procedures 67 5 Setup Utility BIOS and System Diagnostics Using Setup Utility Setup Utility or Basic Input Output System BIOS controls communication between all the input and output devices on the system such as disk drives display keyboard mouse and printer Setup Utility includes settings for the types of peripherals installed the startup sequence of the computer and the amount of system and extended memory Ey NOTE Use extreme care when making changes in Setup Utility Errors can prevent the computer from operating properly Starting Setup Utility E NOTE An external keyboard or mouse connected to a USB port can be used with Set
26. ct name This is the product name affixed to the front of the computer 2 Serial number s n This is an alphanumeric identifier that is unique to each product 3 Part number Product number p n This number provides specific information about the product s hardware components The part number helps a service technician determine what components and parts are needed 32 Chapter 4 Removal and replacement procedures Item Component Description 4 Warranty period This number describes the duration of the warranty period for the computer 5 Model description This is the alphanumeric identifier used to locate documents drivers and support for the computer Computer feet The computer feet are adhesive backed rubber pads There are 2 rubber feet that attach to the corner covers in the locations illustrated below These rubber feet are available in the Rubber Kit spare part number 650734 001 a l l l Component replacement procedures 33 Battery Description Spare part number 6 cell 55 Wh 2 55 Ah Li ion battery 646757 001 3 cell 28 Wh 2 55 Ah Li ion battery 646755 001 Before disassembling the computer follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the compu
27. de cables 650736 001 5 System board includes processor and replacement thermal material For use only on computer models equipped with an Intel Atom N2800 1 86 GHz 676912 001 processor and WWAN capability 1 0 MB L2 cache dual core 6 5 W For use only on computer models equipped with an Intel Atom N2800 1 86 GHz 67691 1 001 processor but not WWAN capability 1 0 MB L2 cache dual core 6 5 W For use only on computer models equipped with an Intel Atom N2600 1 60 GHz 676910 001 processor and WWAN capability 1 0 MB L2 cache dual core 3 5 W For use only on computer models equipped with an Intel Atom N2600 1 60 GHz 676909 001 processor but not WWAN capability 1 0 MB L2 cache dual core 3 5 W 6 Heat sink includes replacement thermal material 651898 001 7 Fan 651897 001 8 Power connector cable 656095 001 9 Battery 6 cell 55 Wh 2 55 Ah Li ion battery 646757 001 3 cell 28 Wh 2 55 Ah Li ion battery 646755 001 10 Base enclosure 663675 001 11 Memory module 2 GB memory module PC3 12800 1600 MHz 652972 001 2 GB memory module PC3 10600 1333 MHz 621565 001 12 WWAN module HP hs2350 HSPA Mobile Broadband Module 668969 001 HP hs2340 HSPA Mobile Broadband Module 632155 001 HP Ic2010 HSPA Mobile Broadband Module 612600 001 HP Ic2000 HSPA Mobile Broadband Module 612599 001 13 RTC battery 599516 001 14 WLAN module Atheros 9485GN 802 11b g n 1x1 WiFi and 3012 Bluetooth 4 0 Combo Adapter 655795 001
28. ded to prevent electrostatic damage Antistatic tape Antistatic smocks aprons and sleeve protectors Conductive bins and other assembly or soldering aids Nonconductive foam Conductive tabletop workstations with ground cords of one megohm resistance Static dissipative tables or floor mats with hard ties to the ground Field service kits Static awareness labels Material handling packages Nonconductive plastic bags tubes or boxes Metal tote boxes Electrostatic voltage levels and protective materials The following table lists the shielding protection provided by antistatic bags and floor mats Material Use Voltage protection level Antistatic plastics Bags 1 500 V Carbon loaded plastic Floor mats 7 500 V Metallized laminate Floor mats 5 000 V Preliminary replacement requirements 31 Component replacement procedures This chapter provides removal and replacement procedures There are as many as 41 screws that must be removed replaced or loosened when servicing the computer Make special note of each screw size and location during removal and replacement Service tag When ordering parts or requesting information provide the computer serial number and model number provided on the service tag It is necessary to remove the battery to obtain these numbers See Battery on page 34 for battery removal instructions Product 3OO00000 Warranty lylyOy Model XXXXXXX A Item Component Description 1 Produ
29. e bte b ssas ise quei apex Upon Ap quU dUA 77 Performing a system recovery csssteddeeicoeod cet unn bcd Hisce intei uices n 78 Using the Windows recovery tools qc etti ta rta e eo n Ur n eret ai 78 Using RUNE se ade ENT T TE 79 Using a Windows 7 operating system DVD purchased separately 79 B Power cord set requirements ssocsicsnsrnidrerr arran N N 81 Requirements for all co nlfles 5 s1acisiaceireids needa rtr gu Rb PHI Db PURUS EM RA voe Eq priv et EM bi pI PIS UE UE 81 Requirements for specific countries and regions sssssssssseeeeeneeeeeeneeerennen 82 L2 07 E 84 ME caecexpsiakb bti T EREPERU REOR FEN EV NEREXEAR KDON ra VOXUENDENE VERE PUREE OFDM ER PUE E ACERO EFE REL DISEASE GEEEUA 85 vii viii Product description Category Product Name Description HP Mini 200 Processors e Intel Atom N2800 1 86 GHz processor dual core 1 0 MB L2 cache 1066 MHz front side bus FSB 6 5 W e Intel Atom N2600 1 60 GHz processor dual core 1 0 MB L2 cache 800 MHz FSB 3 5 W Processor is soldered to the system board Chipset Intel NM10 Express Chipset Graphics Internal graphics Intel Graphics Media Accelerator 3600 shared memory with up to 256 MB supported via Intel DVMT Supports MPEG2 AVC H 264 VC1 WMV9 and Microsoft DX9 Panel 10 l in light emitting diode LED WSVGA AntiGlare 1024x600 display typical brightness 200 nit
30. e the display assembly 1 Position the computer upside down with the front toward yov CAUTION Support the open display assembly when removing the following screws Failure to support the display assembly can result in damage to the display assembly and other computer components 2 Remove the two Phillips PM2 0x5 7 screws 1 that secure the display assembly to the computer Chapter 4 Removal and replacement procedures 3 Remove the display assembly 2 y NOTE Steps 4 through 9 apply only to Compaq Mini CQ10 and HP Mini 110 computer models 4 If it is necessary to replace the display bezel or any of the display assembly subcomponents Flex the inside edges of the top edge 1 the left and right sides 2 and the bottom edge 3 of the display bezel until the bezel disengages from the display enclosure Remove the display bezel 4 The display bezel is available using spare part number 658503 001 Component replacement procedures 63 64 5 If it is necessary to replace the webcamera microphone module d Detach and release the module 1 as far as the module cable allows The module is attached to the display enclosure with double sided tape b Disconnect the module cable 2 from the module c Remove the webcamera microphone module The webcamera microphone module is available using spare part number 658516 001 6 fitis necessary to replace the display panel a Remove the six Phillip
31. el number provided on the service tag It is necessary to remove the battery to obtain these numbers See Battery on page 34 for battery removal instructions T Serial X3900000X IATER EE M Product XXXXXXX lt MBN A Aa OAA ELE N a LI Warranty lylyOy Model XXXXXXX y Item Description Function 1 Product name This is the product name affixed to the front of the computer 2 Serial number s n This is an alphanumeric identifier that is unique to each product 3 Part number Product number p n This number provides specific information about the product s hardware components The part number helps a service technician to determine what components and parts are needed 4 Warranty period This number describes the duration of the warranty period for the computer 5 Model description This is the alphanumeric identifier used to locate documents drivers and support for the computer Chapter 3 Illustrated parts catalog Computer major components Computer major components 15 16 Item Component Spare part number 1 Display assembly 10 1 in WSVGA HD includes display panel cable 2 WLAN antenna transceivers and cables and webcamera microphone module and cable In gloss black finish 658507 001 In Pacific blue finish 658510 001 In Sonoma red finish 658508 001 WSVGA HD display assembly in gloss black fini
32. en press esc and then follow the on screen instructions Press f10 to enter Setup Utility To exit Setup Utility menus choose one of the following methods To exit Setup Utility menus without saving your changes press the esc key and then follow the on screen instructions Use the arrow keys to select Exit gt Exit Discarding Changes and then press enter To save your changes and exit Setup Utility menus press 110 and then follow the on screen instructions or Use the tab key and the arrow keys to select Exit gt Exit Saving Changes and then press enter Your changes go into effect when the computer restarts Displaying system information 1 2 3 Start Setup Utility Select the Main menu System information such as the system time and date and identification information about the computer is displayed To exit Setup Utility without changing any settings use the arrow keys to select Exit Exit Discarding Changes and then press enter Using Setup Utility 69 Restoring factory settings in Setup Utility EJ NOTE Restoring defaults will not change the hard drive mode To return all settings in Setup Utility to the values that were set at the factory follow these steps 1 mo m m Turn on or restart the computer and then press esc while the Press the ESC key for Startup Menu message is displayed at the bottom of the screen Press 10 to enter Setup Utility Use the arrow keys t
33. erminal The 2 WWAN antenna cable is connected to the WWAN module Aux terminal 2 Remove the Phillips PM2 0x3 0 screw 2 that secures the WWAN module to the system board The WWAN module tilts up Component replacement procedures 39 3 Remove the WWAN module by pulling the module away from the slot at an angle 3 E NOTE The WWAN module is designed with a notch 4 to prevent incorrect installation into the WWAN module socket Ey NOTE If the WWAN antennas are not connected to the terminals on the WWAN module the protective sleeves must be installed on the antenna connectors as shown in the following illustration Reverse this procedure to install the WWAN module 40 Chapter 4 Removal and replacement procedures Memory module Description Spare part number 2 GB memory module PC3 12800 1600 MHz 652972 001 2 GB memory module PC3 10600 1333 MHz 621565 001 Before removing the memory module follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 5 Remove the service cover see WLAN module on page
34. eseeeeeee een eene eene 27 Tools regvired Mer LEN t 27 Service considerations csetera erento Fdeeltemtet rab epcen s Elba ship uui ii RE 27 Plasie Pars irronneita aaa a a iati red A a EA RENTA 27 Cables and ConheciGie n0jiiaseeauornoiedeeninnieaiiGwneenw enn 27 Drivehandling ENTE o 28 Creatine tine dutd linbs ose eter retire ores tb tea uM pea RR CIS quU PRIN RUE LE E OUIE 28 Electrostatic discharge damage osssuicenise tees bud mtb SE DU hne SEP i rei UE 28 Packaging and transporting guidelines sssssssssse 30 Component replacement procedures Ju cessere tari e rr do Ert Le HE Ore XU RE aw UR la 32 Nam ET 32 MESSI TTE E ET OT 33 senum 34 SIM select models only qusoccestee a Pegiek voto nue hcm Edita vie b uie bee Fette terc Rive ndun 35 WIAN Dn m 36 WWAN module ERR TT TT T 39 Memory mod le da eandedddeeke nrnie e i 41 RTG batery m 42 aleli Ke N ossneettuMontet ien DEN RR SENDER ERUD REN HHEMMDORAN CER b Mnt E tA SA bild 43 S defe re ENNIO intestate 45 TOP COVER 4s 48 Speakers errete Ee esa uses io noe E sate cueaheeentnasirnes 54 Systemi DOTELneectediec des ER Verte std in astute e uini T Kel bcd os ela 55 p mer C 58 Heatsink NR TT 60 Display assembly anei
35. everse this procedure to install the top cover Component replacement procedures 53 Speakers 54 Description Spare part number Speakers include cable 650736 001 Before removing the speakers follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 and then remove the following components e Service cover see WLAN module on page 36 e Keyboard see Keyboard on page 45 e Top cover see Top cover on page 48 Remove the speakers 1 Release the speaker cable from the clip 1 built into the top cover 2 Remove the speakers 2 from the top cover Reverse this procedure to install the speakers Chapter 4 Removal and replacement procedures System board E NOTE The system board spare part kit includes replacement thermal material Description Spare part number For use only on computer models equipped with an Intel Atom N2800 1 86 GHz processor and 676912 001 WWAN capability 1 0 MB L2 cache dual core 6 5 W For use only on computer models equipped with an Intel Atom N2800 1 86 GHz processor but 676911
36. f you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 5 Remove the service cover see WLAN module on page 36 6 Remove the keyboard see Keyboard on page 45 E NOTE When replacing the top cover be sure to remove the speakers from the defective top cover and install them on the replacement top cover See Speakers on page 54 for speaker removal and replacement instructions Remove the top cover 1 Close the computer 2 Turn the computer upside down with the front toward you Chapter 4 Removal and replacement procedures 3 Release the ZIF connector 1 to which the TouchPad cable is connected and then disconnect the TouchPad cable 2 from the system board Ey NOTE Additional slight force may be needed when releasing the TouchPad cable from the top cover Double sided adhesive is used to attach the TouchPad cable to the top cover surface 4 Remove the two rubber feet 1 on the rear corners of the base enclosure The rubber feet are available in the Rubber Kit spare part number 650734 001 Component replacement procedures 49 5 Remove the seven Phillips PM2
37. ff the computer To learn more about your power settings select Start gt Control Panel System and Security Power Options or refer to the HP Notebook Reference Guide When the computer is in Microsoft Windows press the button to open the default Web browser Buttons 7 8 Item Component Description 1 Power light White The computer is on e Blinking white The computer is in the Sleep state e Off The computer is off or in Hibernation 2 Mute light e Amber Computer sound is off e Off Computer sound is on 3 Wireless light White An integrated wireless device such as a WLAN device and or a Bluetooth device is on e Amber All wireless devices are off 4 Caps lock light On Caps lock is on 5 TouchPad light e Off The TouchPad is on e Amber The TouchPad is off Chapter 2 External component identification TouchPad Item 1 m en ef c3 c3 c ccc ee ee ee ea x ee ee ECC NA Component TouchPad light Description e On The TouchPad is on e Amber The TouchPad is off 2 TouchPad on off button Quickly double tap the TouchPad on off button to turn the TouchPad off and on 3 TouchPad zone Moves the pointer and selects or activates items on the screen 4 Left TouchPad button Functions like the left button on an external mouse 5 Right TouchPad button Functions like the right button
38. from the SIM slot Insert the SIM into the SIM slot and gently push the SIM into the slot until it is firmly seated Component replacement procedures 25 WLAN module Description Spare part number Atheros 9485GN 802 11b g n 1x1 WiFi and 3012 Bluetooth 4 0 Combo Adapter 655795 001 Broadcom 4313GN 802 11b g n 1x1 WiFi and 20702 Bluetooth 4 0 Combo Adapter 657325 001 Intel Centrino Advanced N 6230 WLAN module 631956 001 Ralink 5390GN 802 11b g n 1x1 WiFi Adapter 630703 001 Ralink RT5390R 802 11bgn 1x1 Wi Fi Adapter 691415 001 N CAUTION To prevent an unresponsive system replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region If you replace the module and then receive a warning message remove the module to restore device functionality and then contact technical support Before removing the WLAN module follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 Remove the WLAN module 1 Slide the battery serv
39. g the AC adapter from the computer 4 Remove the battery see Battery on page 34 5 Remove the service cover see WLAN module on page 36 Component replacement procedures 45 Remove the keyboard 1 Remove the two Phillips PM2 0x5 0 screws that secure the keyboard to the computer 2 Rest and secure the computer on its left side Partially open the computer 4 Insert a screw driver or similar thin tool into the keyboard release area and then press on the back of the keyboard until the keyboard disengages from the computer 5 Turn the computer right side up with the front toward you 6 Open the computer as far as it will open 46 Chapter 4 Removal and replacement procedures 7 Lift the rear edge of the keyboard 1 and then swing the keyboard 2 up and forward until it rests upside down on the palm rest 8 Release the zero insertion force ZIF connector 1 to which the keyboard cable is attached and then disconnect the keyboard cable 2 from the system board 9 Remove the keyboard 3 Reverse this procedure to install the keyboard Component replacement procedures 47 Top cover 48 E NOTE The top cover spare part kit includes the TouchPad and TouchPad cable Description Spare part number In gloss black finish 663677 001 In Pacific blue finish 658515 001 In Sonoma red finish 6585 13 001 Before removing the top cover follow these steps 1 Shut down the computer I
40. ice cover latch 1 to release the service cover 2 Release the service cover 2 by sliding it toward the front of the computer 7 NOTE When releasing the service cover it may be helpful to apply additional pressure to the front left corner 3 of the service cover 36 Chapter 4 Removal and replacement procedures 3 Remove the service cover 4 Ef NOTE It is normal for the service cover to flex slightly when it is released You may also hear some popping noises as the service cover tabs disengage from the base enclosure slots The service cover is available using the following spare part number 663676 001 4 Disconnect the WLAN antenna cables 1 from the terminals on the WLAN module Ey NOTE The 1 WLAN antenna cable is connected to the WLAN module Main terminal The 2 WLAN antenna cable is connected to the WLAN module Aux terminal 5 Remove the Phillips PM2 0x3 0 screw 2 that secures the WLAN module to the system board The WLAN module tilts up Component replacement procedures 37 6 Remove the WLAN module by pulling the module away from the slot at an angle 3 f NOTE The WLAN module is designed with a notch 4 to prevent incorrect installation into the WLAN module socket Ef NOTE If the WLAN antennas are not connected to the terminals on the WLAN module the protective sleeves must be installed on the antenna connectors as shown in the following illustration
41. in BrightView WSVGA display assembly in Pacific blue finish includes display panel cable webcamera microphone module and WLAN antenna cables and transceivers 658511 001 10 1 in WSVGA display panel 6585 13 001 Top cover in Sonoma red finish includes TouchPad board and bracket 658515 001 Top cover in Pacific blue finish includes TouchPad board and bracket 658516 001 Webcamera microphone module includes double sided tape 659940 001 External USB DVD RW DL SuperMulti Drive Chapter 3 Illustrated parts catalog Spare part number Description 660843 001 Keyboard for use in the United States includes keyboard cable 660843 031 Keyboard for use in the United Kingdom and Singapore includes keyboard cable 660843 041 Keyboard for use in Germany includes keyboard cable 660843 051 Keyboard for use in France includes keyboard cable 660843 061 Keyboard for use in Italy includes keyboard cable 660843 071 Keyboard for use in Spain includes keyboard cable 660843 121 Keyboard for use in Canada includes keyboard cable 660843 131 Keyboard for use in Portugal includes keyboard cable 660843 141 Keyboard for use in Turkey includes keyboard cable 660843 161 Keyboard for use in Latin America includes keyboard cable 660843 171 Keyboard for use in Saudi Arabia includes keyboard cable 660843 211 Keyboard for use in Hungary includes keyboard cable 6608
42. into display assembly Support for the following WLAN formats e Atheros 9485GN 802 11b g n 1x1 WiFi and 3012 Bluetooth 4 0 Combo Adapter Broadcom 4313GN 802 11b g n 1x1 WiFi and 20702 Bluetooth 4 0 Combo Adapter e Intel Centrino Advanced N 6230 WLAN module e Ralink 5390GN 802 11b g n 1x1 WiFi Adapter Ralink RT5390R 802 11bgn 1x1 Wi Fi Adapter Integrated wireless wide area network WWAN options by way of wireless module Two WWAN antennas built into display assembly Support for the following WLAN formats e HP hs2350 HSPA Mobile Broadband Module e HP hs2340 HSPA Mobile Broadband Module e HP Ic2010 HSPA Mobile Broadband Module e HPlIc2000 HSPA Mobile Broadband Module Chapter 1 Product description Category External media cards Description Digital Media Slot with push push technology supporting e MultiMediaCard Secure Digital SD Memory Card Secure Digital High Capacity SDHC Memory Card Secure Digital Extended Capacity SDxC Supports mini versions by use of an adapter adapter is not included Ports Keyboard pointing devices e Spin AC power e Audio in mono microphone e Audio out stereo headphone e RJ 45 Ethernet includes link and activity lights e USB 2 0 3 ports e VGA Dsub 15 pin supporting 1920 x1200 external resolution 9 60Hz hot plug and unplug and auto detection for correct output to wide aspect vs standard aspect video 93 size Isla
43. ion 1 grounding guidelines 28 guidelines equipment 31 grounding 28 packaging 30 transporting 30 workstation 30 H hard drive precautions 28 product description 1 Index 85 removal 43 spare part numbers 23 24 43 specifications 75 hard drive bracket illustrated 21 removal 44 hard drive connector cable illustrated 21 removal 44 Hard Drive Hardware Kit spare part number 18 21 25 43 hard drive light 10 hard drive rubber isolator illustrated 21 removal 44 headphone jack 11 heat sink removal 60 spare part number hinge removal 65 spare part number 18 21 17 24 60 19 65 J jacks audioin 11 audioout 11 headphone 11 microphone 11 network 11 RJ 45 11 K key components 5 keyboard product description 3 removal 45 spare part numbers 45 16 25 keys Action 5 fn 5 Windows applications 5 Windows logo 5 L left side components 10 light components 8 lights AC adapter battery 10 86 Index caps lock 8 hard drive 10 mute 8 power 8 TouchPad 8 9 webcam 6 wireless 8 M mass storage device precautions 28 removal 43 spare part numbers memory module product description 1 removal 41 21 43 spare part numbers 17 23 24 41 microphone location 6 product description 2 microphone jack 11 model description 33 model name 1 monitor port 10 mouse spare part number 22 23 mute light 8 N network jack 11 Oo operating system product description 4 optical drive precauti
44. moving DIPS from Styrofoam 14 500 V 5 000 V 3 500 V Removing bubble pack from PCB 26 500 V 20 000 V 7 000 V Packing PCBs in foam lined box 21 000 V 11 000 V 5 000 V Preliminary replacement requirements 29 Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment To avoid hand contact transport products in static safe tubes bags or boxes Protect ESD sensitive parts and assemblies with conductive or approved containers or packaging Keep ESD sensitive parts in their containers until the parts arrive at static free workstations Place items on a grounded surface before removing items from their containers Always be properly grounded when touching a component or assembly Store reusable ESD sensitive parts from assemblies in protective packaging or nonconductive foam Use transporters and conveyors made of antistatic belts and roller bushings Be sure that mechanized equipment used for moving materials is wired to ground and that proper materials are selected to avoid static charging When grounding is not possible use an ionizer to dissipate electric charges Workstation guidelines 30 Follow these grounding workstation guidelines Cover the workstation with approved static shielding material Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment Use conductive field service tools such as cutters screwdri
45. n instructions You can also order the DVD by calling technical support For contact information refer to the Worldwide Telephone Numbers booklet included with the computer Z CAUTION Using a Windows 7 operating system DVD completely erases hard drive contents and reformats the hard drive All files you have created and any software installed on the computer are permanently removed When reformatting is complete the recovery process helps you restore the operating system as well as drivers software and utilities To initiate recovery using a Windows 7 operating system DVD ER NOTE This process takes several minutes 1 If possible back up all personal files 2 Restart the computer and then insert the Windows 7 operating system DVD into the optical drive before the Windows operating system loads 3 When prompted press any keyboard key 4 Follow the on screen instructions Performing a system recovery 79 5 Click Next 6 Select Repair your computer 7 Follow the on screen instructions After the repair is completed 1 Eject the Windows 7 operating system DVD and then insert the Driver Recovery disc 2 Install the Hardware Enabling Drivers first and then install Recommended Applications 80 Chapter 7 Backup and recovery 8 Power cord set requirements The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts
46. na cables and transceivers Sequential part number listing 25 26 Spare part number Description 668969 001 HP hs2350 HSPA Mobile Broadband Module 676909 001 System board for use only on computer models equipped with an Intel Atom N2600 1 60 GHz processor but not WWAN capability 1 0 MB L2 cache dual core 3 5 W includes processor and replacement thermal material 676910 001 System board for use only on computer models equipped with an Intel Atom N2600 1 60 GHz processor and WWAN capability 1 0 MB L2 cache dual core 3 5 W includes processor and replacement thermal material 676911 001 System board for use only on computer models equipped with an Intel Atom N2800 1 86 GHz processor but not WWAN capability 1 0 MB L2 cache dual core 6 5 W includes processor and replacement thermal material 676912 001 System board for use only on computer models equipped with an Intel Atom N2800 1 86 GHz processor and WWAN capability 1 0 MB L2 cache dual core 6 5 W includes processor and replacement thermal material 684439 001 Display enclosure in gloss black finish 691415 001 Ralink RT5390R 802 11bgn 1x1 Wi Fi Adapter Chapter 3 Illustrated parts catalog 4 Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures e Flatbladed screwdriver e Magnetic screwdriver e Phillips PO and P1 sc
47. nd style spill resistant keyboard with full numeric keypad Textured pocket style keyboard TouchPad with capacitive multi touch gestures 2 finger scrolling and pinch zoom enabled Power requirements Taps enabled by default 40W AC adapter with localized cable plug support 3 wire plug with ground pin supports 3 pin DC connector Support for the following batteries e 6cell 55 Whr 2 55 Ah Li ion battery GScell 28 Whr 2 55 Ah Li ion battery Security Supports security lock 4 Category Operating system Description Preinstalled e Windows 7 Home Basic 32 bit e Windows 7 Home Premium 32 bit e Windows 7 Professional 32 bit e Windows 7 Starter 32 bit e FreeDOS e USB key recovery support for service refurbish centers and repair centers Serviceability Chapter 1 Product description End user replaceable parts e AC adapter e Battery e Hard drive e Memory module e WLAN module e WWAN module 2 External component identification Item Component Description 1 Action keys Execute frequently used system functions 2 fn key Executes frequently used system functions when pressed in combination with a function key the num lk key or the esc key 3 Windows logo key Displays the Windows Start menu 4 Windows applications key Displays a shortcut menu for items beneath the pointer Keys 5 Item Component Description 1
48. numbers 34 battery bay 12 battery service cover release latch 12 bottom components 12 button components 7 buttons power 7 TouchPad 9 TouchPad on off 9 Web browser 7 17 24 c cables service considerations 27 caps lock light 8 chipset product description 1 components bottom 12 buttons 7 display 6 keys 5 left side 10 lights 8 right side 11 TouchPad 9 computer feet locations 33 computer major components 15 computer part number 32 computer specifications 73 connectors service considerations 27 corner cover spare part number 24 corner covers spare part number 18 D Digital Media Slot 11 display components 6 specifications 74 display assembly removal 62 spare part numbers 16 24 25 62 subcomponents 19 display bezel removal 63 spare part number 19 24 63 Display Cable Kit spare part number 19 66 display enclosure spare part numbers 19 24 26 Display Hinge Kit spare part number 19 65 display hinge spare part number 24 display panel product description 1 removal 64 spare part number 19 24 65 display panel cable removal 66 spare part number 19 24 66 drives preventing damage 28 DVD RW DL SuperMulti Drive precautions 28 spare partnumber 21 24 E electrostatic discharge 28 equipment guidelines 31 Ethernet product description 2 external monitor port 10 F fan removal 58 spare part number feet locations 33 fnkey 5 17 24 58 G graphics product descript
49. o select Exit gt Load Setup Defaults Follow the on screen instructions To save your changes and exit press f10 and then follow the on screen instructions Tors Use the arrow keys to select Exit gt Exit Saving Changes and then press enter Your changes go into effect when the computer restarts 33 NOTE Your password settings and security settings are not changed when you restore the factory settings Exiting Setup Utility To exit Setup Utility and save your changes from the current session If the Setup Utility menus are not visible press esc to return to the menu display Then use the arrow keys to select Exit Exit Saving Changes and then press enter To exit Setup Utility without saving your changes from the current session If the Setup Utility menus are not visible press esc to return to the menu display Then use the arrow keys to select Exit Exit Discarding Changes and then press enter Updating the BIOS Updated versions of the BIOS may be available on the HP Web site 70 Most BIOS updates on the HP Web site are packaged in compressed files called SoftPaqs Some download packages contain a file named Readme txt which contains information regarding installing and troubleshooting the file Chapter 5 Setup Utility BIOS and System Diagnostics Determining the BIOS version To determine whether available BIOS updates contain later BIOS versions than those currently installed on the comp
50. on an external mouse TouchPad 9 Left side mini 96 Item Component Description 1 External monitor port Connects an external VGA monitor or projector 2 Power connector Connects an AC adapter 3 AC adapter battery light e Amber The computer is connected to external power and the battery is charging e White The computer is connected to external power and the battery is fully charged Blinking white The computer is in the Sleep state or the battery charge level is 1096 or less recharge the battery as soon as possible e Off The computer is not connected to external power 4 Vents Enables airflow to cool internal components NOTE The computer fan starts up automatically to cool internal components and prevent overheating It is normal for the internal fan to cycle on and off during routine operation 5 USB 2 0 port Connect an optional USB 2 0 device 6 Hard drive light On The hard drive is being accessed 10 Chapter 2 External component identification wf n O amp Item Component Description 1 Digital Media Slot Supports the following digital card formats e MultiMediaCard e Secure Digital SD Memory Card e Secure Digital High Capacity SDHC Memory Card e Secure Digital Extended Capacity SDxC Supports mini versions by use of an adapter adapter is not included 2 Audio out headphone jack Produce sound when connec
51. ons 28 spare part number 21 24 P packaging guidelines 30 plastic parts service considerations 27 pointing device product description 3 ports external monitor 10 monitor port 10 product description 3 USB 10 11 power button 7 power connector 10 power connector cable removal 57 spare part number power cord set requirements 81 spare partnumbers 22 23 power light 8 power requirements product description 3 processor product description 1 product description audio 2 chipset 1 display panel 1 Ethernet 2 external media cards 3 graphics 1 hard drives 1 keyboard 3 memory module 1 microphone 2 operating system 4 pointing device 3 ports 3 power requirements 3 processors 1 product name 1 security 3 serviceability 4 video 2 wireless 2 product name 1 32 product number 32 17 24 57 R removal replacement preliminaries 27 procedures 32 right side components 11 RJ 45 jack 11 RTC battery removal 42 spare partnumber 17 23 42 Rubber Kit spare part number 18 24 S Screw Kit spare part number 22 24 security cable slot 11 security product description 3 serial number 32 service considerations cables 27 connectors 27 plastic parts 27 service cover location 12 removal 36 spare part number 18 25 37 service tag 14 32 serviceability product description 4 SIM removal 35 speakers removal 54 spare partnumber 17 24 54 specifications computer 73 display 74 hard drive 75 system boa
52. pics in Help and Support f11 recovery tools CAUTION Using 111 completely erases hard drive contents and reformats the hard drive All files you have created and any software installed on the computer are permanently removed The f1 1 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory Software not installed at the factory must be reinstalled To recover the original hard drive image using f1 1 1 If possible back up all personal files 2 f possible check for the presence of the HP Recovery partition click Start right click Computer click Manage and then click Disk Management Ey NOTE If the HP Recovery partition is not listed you must recover your operating system and programs using the Windows 7 operating system DVD and the Driver Recovery disc both purchased separately For additional information refer to the Using a Windows 7 operating system DVD purchased separately section 3 Ifthe HP Recovery partition is listed restart the computer and then press esc while the Press the ESC key for Startup Menu message is displayed at the bottom of the screen 4 Press 11 while the Press F11 for recovery message is displayed 5 Follow the on screen instructions a Windows 7 operating system DVD purchased separately To order a Windows 7 operating system DVD go to hitp www hp com support select your country or region and follow the on scree
53. r a message on the screen reports a successful installation you can delete the downloaded file from your hard drive Using System Diagnostics System Diagnostics allows you to run diagnostic tests to determine if the computer hardware is functioning properly The following diagnostic tests are available in System Diagnostics Startup test This test analyzes the main computer components that are required to start the computer Run in test This test repeats the start up test and checks for intermittent problems that the start up test does not detect Hard disk test This test analyzes the physical condition of the hard drive and then checks all data in every sector of the hard drive If the test detects a damaged sector it attempts to move the data to a good sector Memory test This test analyzes the physical condition of the memory modules If it reports an error replace the memory modules immediately Battery test This test analyzes the condition of the battery If the battery fails the test contact HP support fo report the issue and purchase a replacement battery You can also view system information and error logs in the System Diagnostics window To start System Diagnostics 1 2 Turn on or restart the computer While the Press the ESC key for Startup Menu message is displayed in the lower left corner of the screen press esc When the Startup Menu is displayed press f2 Click the diagnostic test you
54. r can destroy static sensitive devices or microcircuitry Even if the spark is neither felt nor heard damage may have occurred An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle Or the device may function normally for a while then degrade in the internal layers reducing its life expectancy Chapter 4 Removal and replacement procedures Z CAUTION To prevent damage to the computer when you are removing or installing internal components observe these precautions Keep components in their electrostatic safe containers until you are ready to install them Before touching an electronic component discharge static electricity by using the guidelines described in this section Avoid touching pins leads and circuitry Handle electronic components as little as possible If you remove a component place it in an electrostatic safe container The following table shows how humidity affects the electrostatic voltage levels generated by different activities Z CAUTION A product can be degraded by as little as 700 V Typical electrostatic voltage levels Relative humidity Event 10 40 55 Walking across carpet 35 000 V 15 000 V 7 500 V Walking across vinyl floor 12 000 V 5 000 V 3 000 V Motions of bench worker 6 000 V 800 V 400 V Removing DIPS from plastic tube 2 000 V 700 V 400 V Removing DIPS from vinyl tray 11 500 V 4 000 V 2 000 V Re
55. rd removal 55 spare part numbers 17 26 55 T tools required 27 top cover removal 48 spare part numbers 17 24 25 48 TouchPad button 9 TouchPad components 9 TouchPad light 8 9 TouchPad on off button 9 TouchPad zone 9 transporting guidelines 30 U USB port 10 11 V vents 10 video product description 2 WwW warranty period 33 Web browser button 7 webcam 6 webcam light 6 webcamera microphone module removal 64 spare partnumber 19 24 64 Windows applications key 5 Windows logo key 5 wireless antenna locations 6 removal 66 spare partnumber 19 24 67 wireless light 8 wireless product description 2 WLAN module removal 36 spare partnumbers 17 23 24 26 36 workstation guidelines 30 WWAN spare partnumbers 26 WWAN module removal 39 spare part numbers 17 23 39 Index 87
56. rewdrivers Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures E NOTE As you remove each subassembly from the computer place the subassembly and all accompanying screws away from the work area to prevent damage Plastic parts CAUTION Using excessive force during disassembly and reassembly can damage plastic parts Use care when handling the plastic parts Apply pressure only at the points designated in the maintenance instructions Cables and connectors Z CAUTION When servicing the computer be sure that cables are placed in their proper locations during the reassembly process Improper cable placement can damage the computer Cables must be handled with extreme care to avoid damage Apply only the tension required to unseat or seat the cables during removal and insertion Handle cables by the connector whenever possible In all cases avoid bending twisting or tearing cables Be sure that cables are routed in such a way thot they cannot be caught or snagged by parts being removed or replaced Handle flex cables with extreme care these cables tear easily Preliminary replacement requirements 27 Drive handling ACAUTION Drives are fragile components that must be handled with care To prevent damage to the computer damage to a drive or loss of information observe these precautions Before removing
57. s All display assemblies include 2 wireless local area network WLAN antenna cables Supports 16 9 wide aspect ratio Lighted logo on top bezel Memory One customer accessible upgradable memory module slot DDR3 1066 MHz single channel support on computer models equipped with an Intel Atom N2800 processor DDR3 800 MHz single channel support on computer models equipped with an Intel Atom IN2600 processor Supports 2 GB of system RAM 2048x1 Hard drives Supports 6 35 cm 2 5 in hard drives in 9 5 mm 37 in and 7 0 mm 28 in thicknesses Customer accessible Serial ATA Supports Accelerometer hard drive protection Category Description Supports the following configurations e 500 GB 5400 rpm 9 5 mm NOTE A 500 GB hard drive is not supported on computer models equipped with Windows 7 Starter or Windows 7 Home Basic in the People s Republic of China e 320 GB 7200 rpm 7 0 mm e 320GB 5400 rpm 9 5 and 7 0 mm e 250GB 7200 rpm 7 0 mm e 250GB 5400 rpm 9 5 and 7 0 mm Audio and video Single digital microphone Beats Audio with Beats logo Beats hotkey fn b 2 integrated boxed stereo speakers 1 5 W max HP VGA webcam fixed no tilt with activity LED F 2 8 640x480 by 30 frames per second Ethernet Integrated 10 100 RTL8105T VC CG network interface card NIC Wireless Integrated wireless local area network WLAN options by way of wireless module Two WLAN antennas built
58. s or screws These components are included in the Hard Drive Hardware Kit spare part number 664913 001 Description Spare part number 500 GB 5400 rpm 634932 001 320 GB 5400 rpm 645193 001 250 GB 5400 rpm 645191 001 Before removing the hard drive follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 5 Remove the service cover see WLAN module on page 36 Remove the hard drive 1 Disconnect the hard drive connector cable 1 from the system board 2 Remove the Phillips PM 2 0x5 0 screw 2 that secures the hard drive to the computer 3 Use the pull tab 3 to lift the left side of the hard drive until it rests at an angle Component replacement procedures 43 4 Remove the hard drive 4 by sliding it up and to the left at an angle 5 If it is necessary to replace the hard drive connector cable 1 the hard drive screws 2 the hard drive bracket 3 or the rubber isolators 4 remove and replace the components Reverse this procedure to reassemble and install the hard drive 44 Chapter 4 Removal and replacemen
59. s PM2 0x4 6 screws 1 that secure the display panel to the display enclosure Chapter 4 Removal and replacement procedures b Lift the top edge of the display panel 2 and swing it up and forward until it rests at an angle m J uu at c Remove the display panel The display panel is available using spare part number 65851 1 001 7 If it is necessary to replace the display hinges a Remove the four Phillips PM2 0x3 7 screws 1 that secure the display hinges to the display panel b Remove the display hinges 2 The display hinges include the display hinges and brackets and are available using spare part number 65071 1 001 Component replacement procedures 65 8 If it is necessary to replace the display panel cable ACAUTION Make sure the work surface is free of any foreign objects before turning the display panel upside down Failure to clear the work surface can result in scratches and damage to the display panel surface Turn the display panel upside down with the bottom edge toward yov b Release the tabs 1 built into the shielding on the back of the display panel that conceal the display panel connector and secure the display panel cable c Release the adhesive strip 2 that secures the display panel cable to the display panel and then disconnect the display panel cable 3 from the display panel ox d Remove the display panel cable The display panel cable includes the web
60. sh for use only on computer models 668 166 001 equipped with WWAN capability includes WWAN antenna cables and transceivers NOTE For more display assembly spare part information see Display assembly subcomponents on page 19 2 Keyboard includes keyboard cable For use in Belgium 660843 A41 For use in Canada 660843 121 For use in the Czech Republic and Slovakia 660843 FL1 For use in Denmark Finland and Norway 660843 DH1 For use in France 660843 051 For use in Germany 660843 041 For use in Greece 660843 DJ1 For use in Hungary 660843 21 1 For use in India 660843 D61 For use in Israel 660843 BB1 For use in Italy 660843 061 For use in Japan 660843 291 For use in Latin America 660843 161 For use in the Netherlands 660843 B31 For use in Portugal 660843 131 For use in Russia 660843 251 For use in Saudi Arabia 660843 171 For use in Slovenia 660843 BA1 For use in South Korea 660843 AD1 For use in Spain 660843 071 For use in Switzerland 660843 BG1 For use in Taiwan 660843 AB1 For use in Thailand 660843 281 For use in Turkey 660843 141 Chapter 3 Illustrated parts catalog Item Component Spare part number For use in the United Kingdom and Singapore 660843 031 For use in the United States 660843 001 3 Top cover includes TouchPad board and bracket In gloss black finish 663677 001 In Pacific blue finish 658515 001 In Sonoma red finish 6585 13 001 4 Speakers inclu
61. stepi igbo eir vivi he raped sd aloe aret vo e DDR cta aou 62 5 Setup Utility BIOS and System Diagnostics Leeeee eee ee ee eee ee eene eene e eene eene nene neenon 68 SEDED jn qe HO 68 Starting Setup Wily seess M 68 Changing the language of Setup Utility onc nctavendancwsasatundierassiudenoonsndnanten daoakacenneonstaes 68 Navigating and selecting in Setup Utility 1 cerco petra rt br oer Peri Piel 69 Displaying system information us bosser eknricin adeb ieb p paalo ea rdi 69 Restoring factory settings in Setup Utility 2 eov epcncssgask exi xd Eta tu ee bu pando b Sa tad 70 Exiting Setup D nnana S ben pRD M DI sneered PULSU DANN 70 Updating the BIOS NR OO OO TOT 70 Determining the BIOS version 25 tain eR Urs eg nua unes edi ok 71 Downloading a BIOS ipdele aiite aree ERR RIP REESM XURURI UE TRE PPAR PPS HUI RED UPDend 71 Using System Diagnostics ececceeecccccecececcaaeeeeeeeeeeeeeeceeeeeceececeeeeaaeeeaaaaaaaeseneeeeeeeeeeeeeeeeeee aa 72 6 SpecificahionS ENT E CM 73 Gini RULER specifications TTE TEE T T C T 73 10 l inch WSVGA display specifications ooues caseras eer Ri ee Pd xc SE Yea ru pi x pn p eA n th 74 Hard drive specifications lt gt Db vro aarti cer E E E eaten caw cub E Ut emma 75 7 Backup and recovery sssrsssssissssscssssossscosossossncsss nisor TEREREEMEUPEXE REEL REMR AREA POE EY ExE E AXE PU AS Eod nada 76 Backing up your information ooo coires rote debes Iaviqede mai ta tens
62. t procedures Keyboard f NOTE The keyboard spare part kit includes a keyboard cable Description Spare part number Description Spare part number For use in Belgium 660843 A41 For use in the Netherlands 660843 B31 For use in Canada 660843 121 For use in Portugal 660843 131 For use in the Czech Republic 660843 FL1 For use in the Russia 660843 251 and Slovakia For use in Denmark Finland 660843 DH1 For use in Saudi Arabia 660843 171 and Norway For use in France 660843 05 1 For use in Slovenia 660843 BA1 For use in Germany 660843 041 For use in South Korea 660843 AD1 For use in Greece 660843 DJ1 For use in Spain 660843 07 1 For use in Hungary 660843 211 For use in Switzerland 660843 BG1 For use in India 660843 D61 For use in Taiwan 660843 AB 1 For use in Israel 660843 BB1 For use in Thailand 660843 281 For use in Italy 660843 061 For use in Turkey 660843 141 For use in Japan 660843 29 1 For use in the United Kingdom and 660843 031 Singapore For use in Latin America 660843 161 For use in the United States 660843 001 Before removing the keyboard follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unpluggin
63. ted to optional powered stereo speakers headphones ear buds a headset or television audio WARNING To reduce the risk of personal injury adjust the volume before putting on headphones earbuds or a headset For additional safety information refer to the Regulatory Safety and Environmental Notices When a device is connected to the jack the computer speakers are disabled 3 Audio in microphone jack Connects an optional computer headset microphone stereo array microphone or monaural microphone 4 Security cable slot Attaches an optional security cable to the computer NOTE The security cable is designed to act as a deterrent but it may not prevent the computer from being mishandled or stolen 5 USB 2 0 ports 2 Connects optional USB 2 0 devices 6 RJ 45 network jack Connects a network cable Right side 11 Bottom 12 3 Item Component Description 1 Battery bay Holds the battery and the subscriber identity module SIM slot 2 Battery service cover release latch Releases the battery from the battery bay and the service cover from the computer 3 Service cover Provides access to the hard drive bay the memory Chapter 2 External component identification module slot the WLAN module and the WWAN module select models only 3 Illustrated parts catalog Service tag 14 When ordering parts or requesting information provide the computer serial number and mod
64. ter by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer Remove the battery 1 Slide the battery service cover release latch 1 to release the battery 2 Pivot the front edge of the battery 2 up and back 3 Remove the battery 3 from the computer To insert the battery 1 Align the tabs on the rear edge of the battery with the notches on the rear edge of the battery bay 2 Pivot the front edge of the battery down into the battery bay until it is seated The battery release latch will automatically lock into place 34 Chapter 4 Removal and replacement procedures SIM select models only f NOTE The SIM is provided by the end user as a security measure for the WWAN module The SIM should be removed placed into a static dissipative container and then replaced when the computer is reassembled Before removing the SIM follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 Remove the SIM 1 Press in on the SIM 1 to release it from the SIM slot 2 Remove the SIM 2
65. tions Creating a system repair disc select models only by using the installed optical drive select models only or an optional external optical drive Backing up your information Creating a system image select models only Scheduling automatic backups select models only Creating system restore points Recovering individual files Restoring the computer to a previous state Recovering information using recovery tools Ey NOTE For detailed instructions perform a search for these topics in Help and Support In case of system instability HP recommends that you print the recovery procedures and save them for later use E NOTE Windows includes the User Account Control feature to improve the security of your computer You may be prompted for your permission or password for tasks such as installing software running utilities or changing Windows settings Refer to Help and Support for more information Chapter 7 Backup and recovery Backing up your information Recovery after a system failure is as good as your most recent backup You should create system repair discs select models only by using the installed optical drive select models only or an optional external optical drive and your initial backup immediately after software setup As you add new software and data files you should continue to back up your system on a regular basis to maintain a reasonably current backup The system repair discs select models only are used
66. to turn on automatically when high temperature conditions exist These conditions are affected by high external temperatures system power consumption power management battery conservation configurations battery fast charging and software requirements Exhaust air is displaced through the ventilation grill located on the left side of the computer Before removing the fan follow these steps 1 Shut down the computer If you are unsure whether the computer is off or in Hibernation turn the computer on and then shut it down through the operating system 2 Disconnect all external devices connected to the computer 3 Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer 4 Remove the battery see Battery on page 34 and then remove the following components e Service cover see WLAN module on page 36 e Keyboard see Keyboard on page 45 e Top cover see Top cover on page 48 e System board see System board on page 55 Remove the fan 1 Turn the system board upside down with the rear toward you 2 Disconnect the fan cable 1 from the system board 3 Remove the Phillips PM2 0x4 6 screw 2 that secures the fan to the system board 4 Disengage the tab 3 on the fan from the slot on the system board 58 Chapter 4 Removal and replacement procedures 5 Remove the fan 4 Component replacement procedures 59
67. up Utility only if USB legacy support is enabled To start Setup Utility follow these steps 1 Turn on or restart the computer and then press esc while the Press the ESC key for Startup Menu message is displayed at the bottom of the screen 2 Press 10 to enter Setup Utility Changing the language of Setup Utility 1 Start Setup Utility 2 Use the arrow keys to select System Configuration gt Language and then press enter 3 Use the arrow keys to select a language and then press enter 4 When a confirmation prompt with your language selected is displayed press enter 5 To save your change and exit Setup Utility use the arrow keys to select Exit gt Exit Saving Changes and then press enter Your change takes effect immediately 68 Chapter 5 Setup Utility BIOS and System Diagnostics Navigating and selecting in Setup Utility To navigate and select in Setup Utility follow these steps 1 2 Turn on or restart the computer and then press esc while the Press the ESC key for Startup Menu message is displayed at the bottom of the screen e To select a menu or a menu item use the tab key and the keyboard arrow keys and then press enter or use a pointing device to click the item e To scroll up and down click the up arrow or the down arrow in the upper right corner of the screen or use the up arrow key or the down arrow key e To close open dialog boxes and return to the main Setup Utility scre
68. urface temperature limits defined by the International Standard for Safety of Information Technology Equipment IEC 60950 iv Safety warning notice Table of contents JM 77 1 2 External component identification Lecce eee eee eee eee eee eee eee een eene tesa teta sete aset nane 5 KW PIER LUE 5 Display coast ipa se a dm Pa oa be Apdo De M vet MUNI UM POM LM EM E MU adu OS 6 BUONE p E E E E a A E A 7 lighis T A ET DT LT E R 8 TouchPad aone A A a a E E H 9 leide m cr 10 bigis ctio ie uci E Pans PRU Mi ME 11 inpet T 12 3 Wusimoted poris catalog uussessuvissse vete YRPECE aR a 13 Semice tag sse er ese aes een un ein Lab E RE R Gata neha es esee ieee 14 Computer major components sssssssssssseeseeeee emen et St e ene eee nnne nn rn nr rrr nennen eene 15 Display assembly subcomponents senses trii Er eto tir olk sev aut kt ed eR ER DR al ta uin Edi hs Haud gla n 19 Wu ear T anions 21 LY retell fol evel pars usado Sai rti ee ane tei n RAN GU cH x DR MR E PR ree eU KE dU DM MI E 22 Sequential part number listing 1 recte rra rtt re eer rhet ERE esi bn IEEE FEN SETA P EXTARE E P IARE 23 4 Removal and replacement procedures eee eee esee eese ee eese eee eene e esae sense esas te nne 27 Preliminary replacement requirements sssssssssssss
69. uter you need to know the version of the system BIOS currently installed BIOS version information also known as ROM date and System BIOS can be displayed by pressing fn esc if you are already in Windows or by using Setup Utility 1 Start Setup Utility BIOS 2 Use the arrow keys to select Main 3 To exit Setup Utility BIOS without saving your changes use the tab key and the arrow keys to select Exit gt Exit Discarding Changes and then press enter Downloading a BIOS update Z CAUTION To reduce the risk of damage to the computer or an unsuccessful installation download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter Do not download or install a BIOS update while the computer is running on battery power docked in an optional docking device or connected to an optional power source During the download and installation follow these instructions Do not disconnect power from the computer by unplugging the power cord from the AC outlet Do not shut down the computer or initiate Sleep or Hibernation Do not insert remove connect or disconnect any device cable or cord 1 Windows 7 Select Start gt Help and Support gt Maintain Windows XP Select Start Help and Support and then select the software and drivers update 2 Follow the on screen instructions to identify your computer and access the BIOS update you want to download 3 At the download
70. vers and vacuums When fixtures must directly contact dissipative surfaces use fixtures made only of static safe materials Keep the work area free of nonconductive materials such as ordinary plastic assembly aids and Styrofoam Handle ESD sensitive components parts and assemblies by the case or PCM laminate Handle these items only at static free workstations Avoid contact with pins leads or circuitry Turn off power and input signals before inserting or removing connectors or test equipment Chapter 4 Removal and replacement procedures Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation When seated wear a wrist strap connected to a grounded system Wrist straps are flexible straps with a minimum of one megohm 10 resistance in the ground cords To provide proper ground wear a strap snugly against the skin at all times On grounded mats with banana plug connectors use alligator clips to connect a wrist strap When standing use foot straps and a grounded floor mat Foot straps heel toe or boot straps can be used at standing workstations and are compatible with most types of shoes or boots On conductive floors or dissipative floor mats use foot straps on both feet with a minimum of one megohm resistance between the operator and ground To be effective the conductive must be worn in contact with the skin The following grounding equipment is recommen
71. want to run and then follow the on screen instructions E NOTE If you need to stop a diagnostics test while it is running press esc 72 Chapter 5 Setup Utility BIOS and System Diagnostics 6 Specifications Computer specifications Metric U S Dimensions Width 26 8 cm 10 55 in Depth 19 1 cm 7 52 in Height front to back 2 3 to 3 3 cm 0 91 to 1 29 in Weight 1 26 kg with 3 cell battery 2 77 lb with 3 cell battery 1 40 kg with 6 cell battery 3 09 Ib with 6 cell battery Input power Operating voltage and current 19 5 V dc 2 05 A 40W Temperature Operating 5 C to 35 C 41 F to 95 F Nonoperating 20 C to 60 C 4 F to 140 F Relative humidity noncondensing Operating 10 to 90 Nonoperating 5 to 95 Maximum altitude unpressurized Operating 15 m to 3 048 m 50 ft to 10 000 ft Nonoperating 15 m to 12 192 m 50 ft to 40 000 ft NOTE Applicable product safety standards specify thermal limits for plastic surfaces The device operates well within this range of temperatures Computer specifications 73 10 1 inch WSVGA display specifications 74 Metric U S Dimensions Height 23 5 cm 9 3 in Width 14 3 cm 5 6 in Diagonal 25 7 cm 10 1 in Number of colors 262 144 Contrast ratio 500 1 typical Brightness 200 nits typical Pixel resolution Pitch 0 2175 x 0 2088 mm Format 1024 x 600 Configuration RGB vertical

HP Mini 200

Contents

Download Pdf Manuals

Related Search

Related Contents