Budgit Hoist AC Brake
Contents
1. NOTES BUDGIT 414 West Broadway Ave P O Box 769 Muskegon Michigan 49443 0769 800 955 5541 800 742 9270 FAX Printed in U S A Copyright 2007 Lift Tech International division of Columbus McKinnon Corporation2. Page 4 1 PHASE HOIST MOTOR AP AUX MAIN RA VIO aut DR oo pa en x TRANSFORMER ICPT RAKE MOTOR amp TRA AS ILLUSTRATED ON P B STATION EN BUTTON DAMAGE AND A R H DIRE OTOR LEADS ORA 333231 04 Page 5 3 HOOK RAIS SEVERE OAD MAY R MPROP G INP 0 E AVEC VIGUEUR 00 ES 0 gt B STATION EN UP B AMAGE AN UTTON DAMAGE DA A TION BY NORMES EN Page 6 333233 01 CONTACTOR TRANS BRAKE MOTOR amp TRANSFORMER NEED TO AS ILLUSTRATED ON D G 3 SHEE gt BUTTON JAMAGE AND A ECTION BY AA AVERTISSEMENT CET EQUIPMENT DOIT EN ACCORDANCE AVEC VIGUEUR 333233 02 Page 7 ETRE MIS A LA NCE AVEC LES NORMES EN 333233 03 Page 8 12 113 STATION 333233 04 Page 9 NOTES
3. INSTALLATION INSTRUCTIONS RETROFIT REPLACEMENT KIT BUDGIT ELECTRIC HOIST AC BRAKE Disconnect power source from hoist Lock disconnect in the off position and tag to prevent accidental application of power Disconnect motor leads from the controls Remove brake Remove motor bolts and pull motor away from gear case as shown in illustration Pull two new 18 16 AWG stranded wire leads labeled HB1 and HB2 through the motor barrel and out the end bell as shown in illustration The two wires should be approximately 24 longer than the motor barrel Reinstall motor pulling wire leads through the gear case wire passage Install brake using provided hardware Do not use hardware provided with the DC brake 2 NO2112 3 8 16 x 1 Hex socket head cap screw 2 10095703 3 8 Lock washer socket head cap screw At the brake end of the motor connect the DC brake leads together 1 and 1A with a wire nut Remove reversing contactor and install provided contactor 4 normally open Note 3 normally open 1 normally closed contactor will not function properly Wire the hoist using the provided 3 22700310 7 5 black wire jumpers and the appropriate wiring diagram Sheet 2 115V single phase without transformer Sheet 3 230V single phase without transformer Sheet 4 115V single phase with transformer Sheet 5 230V single phase with transformer Sheet 6 230V three phase single speed hoist Sheet 7 460V three pha
4. se single speed hoist Sheet 8 200V or 575V three phase single speed hoist Sheet 9 All voltages two speed hoist Power unit and test per the procedure outlined in section 7 12 of the Operation Parts and Service Manual April 2007 COPYRIGHT 2007 Lift Tech International division of Columbus McKinnon Corporation PART NO 113535 35 FOR 2 VOLT THE EWIRED AS ILLUSTRATED ON L A WARNI IMPROPER HOO G MOTOR LEADS O E PUSHBU ST BE EFFECTIVELY O APPUI E CET EQUI EN ACCORDANCE AVEC LES NORMES EN VIGUEUR 333231 01 Page 2 115 VOLT THE TO BE RE HEET 1 EN BUTTON DAMAGE AND A ION BY IS EQUIPMENT MUST BE EFFECTIVELY NDED ACCORDING TO APPLICABLE 3 SEMENT UIPMENT DOIT ETRE M E AVEC LES NC DANCE 333231 02 Page 3 MAIN NON 2 PINK 32 N G THIS HOIST FOR 230 VOLT KE MOTOR amp TRANSFORMER NEED TO B USTRATED ON DR HEN BUTTON SE AND A EQUIPMENT MUST BE EFFECTIVELY GROUNDED ACCORDING TO APPLICABLE CODES 4AAVERTISSEMENT S ALA TERRE EN VIGUEUR 333231 03
Download Pdf Manuals
Related Search