Home

The Kawasaki Ninja 250 FAQ

1. Running them toward the loose end of their tolerance will normally increase low end power at the cost of top end make the valve train noise louder One of the most important things aside from staying within the tolerances is to set all the intake valves clearances as close as possible to one another and do the same of exhaust This just like synchronizing carbs has a big effect on how smooth the engine runs especially at low speeds Without going into great detail this is because the carb sync only determines that the intake valves have the same pressure upstream but the timing point at which the valve opens and closes determines how much of that air will get into the cylinder These combined ensure each cylinder is doing equal work and therefore run smoother and more efficiently My recommendation to those that are mechanically inclined is to learn how to do this yourself because nobody will pay attention to detail or be more concerned about scratching your bike than you If you have a friend that knows how to do this seek help for the first time preferably have him demonstrate on his own bike first and see if it still runs afterwards After valve adjustment resync the carbs because if the valves weren t set correctly then the airflow may change slightly requiring the carbs to be rebalanced Do really need to adjust the valves every 6000 miles Leon Wed Jul 12 13 34 34 2000 If you re taking it easy with the bike
2. Tank bag Esoteric FriJun 23 21 00 35 2000 have a Roadmaster tank bag It has a magnet in the middle and four arms with magnets on them it also has a strap that clips around the front It stays very solid on the bike and also has a clear vinyl front to place maps and such behind convenient for DVD rentals I ve found But you ll want to keep your interac and credit cards away because those strong magnets would kill them almost instantly Tail bag Bill K Wed Jun 27 16 03 02 2001 The cheapest option is to just use a duffel bag and a bungee net but since had money burning a hole in my pocket got an Eclipse Rumble Pack tail bag It s 12x11x7 high expandable to 12 and fits nicely on the rear portion of the 250 seat It has an adjustable bungee cord attach system and the four hooks fit perfectly on the 250 bike hooks Costs about 65 95 Eclipse makes another nice one called The Fast Pack and Tour Master Ocelot and Lockhart make some good ones too Saddle bags Motorbike Mary Wed Jun 27 17 37 27 2001 am currently using Chase Harper Stealth Bags on my 250 and have been relatively happy with them Here s the scoop Pros e larger capacity than expected can easily carry a liter bottle and a bag of chips in each side Or a six pack minus the cardboard holder micro brew for after the ride e easy to open from back or front e made of stiff neoprene material that even held up my parked bike when got k
3. plug condition can point to engine problems Installation is reverse of removal apply very little torque to the plugs with your wrench Permatex anti seize is recommended to protect the plug threads NOTE use only the recommend spark plugs listed here There have been accounts of plug failure including detonation when using Champion or Autolite replacements How do I service the brakes How do I bleed the brake lines Steve Fri Oct 22 03 14 25 1999 Ok first you need 3 tools phillips screwdriver cresent wrench to fit the bleeder screw on the caliper about 18 of clear tubing that fits tightly over the bleeder Grab some good clean brake fluid and a bottle of Coke Dew etc while you re out First clean the master cylinder caliper bike and maybe the garage while drinking the Coke When done with the bottle clean it out and fill it about halfway with brake fluid then drop the end of the tubing into it Now remove the cap on the master cyl and top off the fluid Put towels rags etc under around near anywhere the brake fluid could possibly go if it leaves the master cyl at high speed and it will Now CAREFULLY squeeze the brake lever and open the bleeder screw Pump the lever a few million times while keeping the reservoir full Eventually there will be no bubbles coming out of the hose in the bottle of brake fluid Squeeze the lever one more time hold it back and close the bleeder screw All done Bleeding brakes i
4. 100 ft lbs Ideal 2 ratcheting torque wrenches 50 each one in inch lbs one in ft lbs Bigger one must handle 100 ft lbs max e Service Manual and Supplement Very bloody handy If you don t have the service supplement you can at least get the torque values from this page Gravy e Short ratchets for hard to reach places More screwdrivers Circlip tool Magnetic pick up tool for stuff you drop Kawasaki valve adjustment tool see Page 44 The usual supplies WD 40 cable lube chain lube brake rotor cleaner A jack for lifting the bike by the motor Bottom line Buy tools when they re on sale and buy the right tool for the job when you need it Never buy cheap tools unless you re just buying a screwdriver to hit with a hammer they cause more problems than they re worth Now you know what you need you can walk through Sears and see what s on sale the next time you re in the mall What kind of battery charger can I use Jeb Mon Nov 27 16 57 36 2000 The Battery Tender brand Plus model is a commonly used charger It s about 35 but well worth it It comes with a harness that you can permanently mount to the bike so you can plug the bike in when you get home and be sure to have a fresh battery in the morning It has a smart circuitry system that will not charge the battery any more once the battery is fully charged to prevent damage I ve brought several dead batteries back to life with mine including the huge battery
5. B E E ET N E E E A E E EEE E EEE T 17 GONO a EE O 17 OC ae a a ret alee tees a a a ae 17 Widder Neale dC lOV ES aiene a A nat endua Me nediqareens 18 X01 6 Keren eer ere mane in ter tee etna ert errr Mere ce erae eT nee arene ter ene ener reer ae 18 INTC DOOS TALI DECESSI Yy anaes tices a a a ious anatnrs usa a 18 What dre some models to conside ousiiecranien e e i 18 AE a a a eae oraatuoen iia oes aearatetece se terateeeals 18 Army BOOS cts carte acacia a E Ne 19 Parachute Bool unaia aa a aa a 19 OMe enin aaa aa a a a e E 19 FRAN Oe a E A 19 Earp Sea EE 20 Aros SWU Enea a wiboeemesusastarhoneaaciatien 20 PO VC AC C0 anaa a a panama aenecanenens aban 20 BACK DlOlC Cl OF serienn E in aauaseieedocamuns densa oniuseaaaeast 20 Do I really need to wear all this Stuff cc eeccececccceceeeeeeeeceeeeeseaesseeeeeeeeeaaas 21 What factors should I consider when looking for these items ccccsseeeees 21 What do I need to know about insurance 0 0 ccccccececceeeeeesesessesseeeeeeceeeeeeeeeneaaaas 22 How much is insurance going to cost me for the Ninja 250 cc ccceeeeeeeees 22 should Tsetany extended coverage esra E a 22 What insurance companies should I check Out oossonnnnnesesssseeresssssseerrssssssese 22 SHOUT Take 2am WISESCOUESC nsonatsseswacaddesenesvanadencedensesiediodiabquademsdeidhedehtiuacsamdiadinvaacees 23 Wiiat isan WISE COuUtse leran T ete aie twioees 23 Is the course hard wil
6. Need totepair a crtacked Lali D ssa bieco aidi e a edea 72 I m trying to find touch up paint to cover some Scratches cccceceseeeeeeeeeeeeees 72 My bike was wrecked but it wasn t my fault oo eeeseeeececeeeeeeeeseeeeeeeeeaaas J2 need recommendations for tOOIS Parts occsacscasicinss coiedbesessnsbusstbencontassuwesdacecdieedenniieiusdestcesdess 72 What should a good set of tools include 0 0 eee cece cece seeeeseececeeeaaeeeeeceeeeeseaeeeeeseeeeeeaaas 72 What kind of battery charger can Use 0 cee ecccccccceesessseeeececeeaaeesseeceeeeeaseeeeseeeeeeessaaeeses 73 ini Royale O saeeme meer eee rrmeen etre errr reat hart Se eater nonce ert tre tener mre creme cee reir teen re er ne ree re eae trier 74 PELOTAN E ecn a a sausesaie senile uneecane Sus naaeaae eaaneceeseunecubwunaessadies 74 want tOUperade my exaust oaoa ei deacon a sbabian sedcmennenGths 74 WhatimOdels are av alaDle sksseckcntersuimteen ues a a a 74 MUZA onetime ee en nr en Ome aoe Pere teens Pre En ee ae em ree Pere ence 74 How much difference does the Muzzy exhaust system make cccccceeeeeeees 74 Do I have to remove the centerstand to install a Muzzy exhaust c008 74 Flow dol repack he MUZZY iai N E a Manito eibueleceds 74 OG FL FIN oc a ema ca ccna Paree studies lacac hunts 75 COD Tenna ate stesoe cea ation eee eee ee eee 75 Do I have to rejet when I put in a new exhaust SysteM ccecseseeeeeeeeeeeeeeeeeeae
7. So maybe next time take the little guy realize that the bigger road thugs will pull away from me On the longer sections of Highway 12 on the way eastward from 123 towards the turnoff to Forest Road 25 and Windy Ridge will be in the back But then the road turns tight and it is corner after corner Then all you see is drop off then rock wall then drop off Then the turns come so fast you can t count them Then don t have to roll off the throttle on the Ninjette don t have to brake between apexes then Size Matters Along with the size of the grin on my face 2001 Jenner 106 Journeys Indian Summer on the Crest VFR Pilot Mon Nov 15 00 22 46 1999 Got up expecting to do chores all day and found that it was a perfect seventy degree fall day Checked oil gas tire pressures threw on the leathers grabbed the tank bag fired up the Ninja and headed out for the Crest For those of you who don t know the Angeles Crest Highway is a two lane strip of blacktop with 57 miles of uninterrupted curves The road ranges in altitude from one to eight thousand feet rising and falling over several alpine passes as it follows the spine of the San Gabriel mountains north and east of L A To the south is the L A basin the Pacific ocean and Catalina island on the horizon To the north is the Mojave desert replete with pastel washes of reds yellows and browns the whole thing being framed by the peaks of the High Sierras beyo
8. Try making circles in an empty parking lot at about 10 15 MPH much like Leon suggests Keep making the circle tighter to gain confidence and eventually it won t go over any further scraaaape Dealing with crosswinds VFR Pilot Tue May 2 19 57 49 2000 Motorcycles in general and cowled sportbikes in particular are subject to weaving in crosswinds I ve ridden in gusting 655mph winds that were blowing directly across the road and it s no fun at all When the wind gusts it forces you in the direction that it s blowing so you naturally must lean into it to prevent being blown into the next lane Then the gust will abruptly let up and the bike will suddenly dart in the direction that you were leaning tracing a weaving path that makes a slobbering drunk look like the picture of sobriety I thought that was worried that day until realized that the cagers around me were looking panic stricken and getting just as far away from me as they could But there are several things that can help 1 Stick your windward knee out effectively making yourself asymmetrical to the wind Basically when you get hit by a gust your leg scoops some of it up so the wind pulls you in at the same time it pushes you away it cuts the effect substantially 2 Slow down At lower speeds crosswinds have less effect What found downright dangerous at 7Omph proved to be controllable though exciting at 50 3 Find a moving wind break Following a tractor
9. but I d take a serious look at what DID has to offer in the rest of their product line up before made any decisions As far as rear sprockets go lower weight is indeed a benefit the looks are subjective If you do go with an alloy sprocket make sure that it is hardened don t know for sure what processes they use to harden them hard anodization cyro but take it on reliable advice that the hardened ones have much better wear properties than the unhardened There are a lot of people that have run both hardened and unhardened rear sprockets and the hardened ones always last much longer My preference is for AFAM sprockets as have never heard a bad word in regards to their products ever They sell a hardened rear sprocket but the looks of it are an individual thing it only comes in a dull grey finish but I ll take performance over looks any day of the week Second on my list of sprocket manufacturers is Renthal a lot of European riders like this brand as it is readily available to them but have heard a few like 2 or 3 in the past 3 yrs complaints that the tolerances were off I m not sure if they offer hardened sprockets but assume they do Third is Sprocket Specialists sprockets In the past year alone have heard multiple complaints regarding tolerances and the sprocket as a whole being out of round was not flat They offer a lightened rear sprocket that many people swear by and as I have no personal experience am
10. give you better protection and are lighter have better venting offer removable padding for cleaning and so on But a good full face street helmet that has both DOT and Snell approval will still only cost you in the neighborhood of two to three hundred dollars and will have enough features to keep most of us happy personally use a mid line Shoei RF800 but Arai and AGV also offer similar models It s probably a wise move to stay away from bargain basement brands If you ever have to rely on your helmet to protect you in a bad crash you ll be glad you got a good one Should get a full face helmet Neal D Mon May 15 06 48 22 2000 When was sixteen a guy was wheeled into the emergency room and was a mess He had fallen off his bike in a slow speed slip His face was mangled and he had been wearing a helmet an open face one swore then that would always wear a helmet and that it would only be a full face had the misfortune of going down on a slick and wet corner landing on my belly and scraping my face on the ground My full face helmet literally took it on the chin Yeah it ain t gonna happen to you What are some good models gabe846 Tue Apr 25 17 43 41 2000 How good a helmet you get depends on how much how far you will ride the bike If you want to ride more than 40 minutes at a time and over 60 mph you need a decent helmet Either that or never try on a quality helmet Ignorance is bliss Other than that
11. might paint it red later I ve dubbed my Ninja design ZX 2R but that not it s original meaning ZX 2R was originally a nickname for the ZXR 250 which is not sold in the U S However Ninjas of larger displacement follow this naming convention as is described in more detail on the ZX 2R decal page Anyway like my design well enough to make it the mascot of the FAQ a presentation of the potential of the EX250 as a motorcycle not just as an excellent bike for the beginning rider but also as a very Capable sport machine with a little work The Ninja 250 FAQ has always been a site free of third party advertisements and it will remain that way However it does require a significant amount of work to maintain the FAQ and so feel justified using this space for promoting a few products of my own design the ZX 2R decal kit and seat cowl Can I get ZX 2R decals Jeb 13 May 2004 I ve never particularly liked the model name EX250 1 think it s a shame that Kawasaki came up with a ZX model designation for its line of Ninja sportbikes but left out the 250cc and 500cc models There s the ZX 12 ZX 11 ZX 9 ZX 7 ZX 6 and the EX250 amp EX500 Well decided to come up with a ZX 2 logo and combine it with some Ninja and Kawasaki logo decals to make a kit to refurbish the look of the bike and make it stand out a bit more The kit components were modelled after the current ZX 6R graphics configuration simple clean a
12. milk Crash 1 this year was exactly one block from my apartment What all this means is that if you swing your leg over your machine you need to dress as if you are going to crash at 80 mph because that s about as fast as most people ride as soon as you start moving That gives you a little margin Protective gear should be a balance of protection comfort style and value These four factors should be balanced according to your needs and tastes Let s examine each factor First and most heavily weighted should be protection It should resist abrasion to 80 100 mph and should provide impact protection at all the likely and fragile impact points head spine hips elbows hands ankles and knees The best materials are heavy cordura nylon Kevlar fabric and leather The leather should be something specifically made for motorcycling not fashion leather Fashion leather is selected for softness and light weight not abrasion resistance A well selected piece of leather offers more abrasion resistance than a thicker lower quality piece Hence a Z Custom suit will tear less easily than a thicker but cheaper Pakistani made suit The armor in your back protector should have a CE label on it or should be made to that standard CE is the European agency that writes standards for thousands of consumer products like our Underwriter s Laboratories But the USA has no standard for motorcycle armor What that means is a lot of armor in the cheaper
13. non leaning traction Wider tires are necessary when carrying heavy loads or if the bike makes a lot of power the EX250 typically does neither of these things so wider tires are usually of no benefit Taller and wider tires both weigh more so you have additional unsprung weight to deal with slows down suspension action Considering all of these points use a 90 profile front tire on my bike with a 120 80 tire on the back and suspension setup that offsets these changes lower front suspension higher rear This provides the best performance and handling in my opinion Do 120 width tires really work better on the rear Jeb Sat Nov 3 11 39 09 2001 The Ninja 250 s rear rim was designed for a 120 width tire the EX250 E model came stock with a now discontinued Dunlop K530 120 80 rear tire The EX250 F 1988 model however has the same size rim but comes stock with a Dunlop K630 130 80 tire mounted Kawasaki actually put a wider tire on their own rim than is ideal for the wheel width the 130 is slightly pinched in the rim while the 120 is right at home The 120 80 tire is better than a 130 90 usual rear stock replacement in many ways First off the 120 80 tire typically weighs four pounds less than a 130 90 of the same model This means less dead weight on the chassis less rotating mass for the engine to turn less unsprung weight for the suspension to carry The lower profile is also more rigid The tire width Is the ideal s
14. with the other riders one on another Bandit 1200 and the other on a ZRX1100 The little Ninjette would have been hard pressed to reel them in on some of the straight stretches of Highway 12 But in the twisties where the road Is tight cambered well even though slightly bumpy the Ninjette would have shined Dollars to donuts too wouldn t have been as tired when we hit Windy Ridge So why in the heck would this Bandit 1200 rider want to give up that performance for a little 29hp on a good day Ninja 250 Simple didn t need the Bandit s horsepower or it s weight for those roads As a matter of fact the 100 horsepower of the Bandit was a hindrance on those roads even to my usually conservative throttle hand J ust look at the estimated numbers Suzuki 1200 Bandit Weight including me 800 Ibs Horsepower estimate 110 hp Horsepower to weight ratio 7 2 lbs hp Gas Mileage 31mpg Kawasaki Ninja 250 Weight including me 550 Ibs Horsepower estimate 29 hp Horsepower to weight ratio 19 lbs hp Gas Mileage 70mpg On the cold numbers the Bandit 1200 looks like a better deal It pushes half the weight with each horsepower It also weighs over 200 lbs more Oh and then have to fill up the tank every 115 miles On a nice level road or even in the long sweepers the Bandit is in it s stride When the road is so tight it literally goes turn turn turn the Ninja really shines The 110 hp and the extra 200 pounds aren t
15. 7 gram stick on weights that break apart like a Hershey bar The weight should be placed on the side of the wheel opposite the heaviest point the heaviest point will be at bottom so the weight goes at the top Usually one weight is enough and often 1 2 of a weight will suffice Occasionally 1 5 or two weights will be necessary to even everything out It takes a bit of time but when you re cruising smooth at 80 mph you ll know where that extra time went How do I remove the fairing fuel tank etc Wes Wed Nov 21 13 58 02 2001 Bar ends Remove master cylinder and electrics from handlebar remove handlebar from riser Soak handlebar in very hot tap water for 10 minutes then remove bar end screw or Use very good 3 Phillips bit with ratchet and or impact driver very hard but may take less time Lower Two screws per side to the upper fairing one bolt per side near the exhaust header pipe joint one bolt in the middle under the radiator Upper Remove four screws holding lower fairing to upper fairing One bolt under each mirror two gas tank bolts per side Disconnect signal light wires from their harnesses Carefully pull upper off the fairing stay bracket that also retains the headlight and gauges and work around the forks Side Panels Remove seat One screw each side Carefully pull from rubber stoppers front and rear Fuel tank Remove side panels Remove four bolts two per side that connect upper fairing to tank it i
16. Auto 4 29 Shell Rotella 15w 50 Auto 1 39 e Golden Spectro ranks highest in anti wear additives with Shell Rotella second the others rated well e Best in Extended Oil Changes is Moble 1 Tri Syn second Motul 3100 others rated well e Best in Low Mileage Extended Sit Time is Shell Rotella second Motul 3100 others rated well e Best in Hot Running Evaporative Losses is Moble 1 Tri Syn second Belray EXP others rated well e Best in Viscosity Retention is Shell Rotella second Belray EXP others rated well This doesnt include all the data but most of it Remember this list is of oils 5 00 or less there may be better oils but you will have to pay 7 95 to 9 95 a quart and the difference in protection is not that much greater if any at all Is synthetic oil really all that great Jeb Sat Apr 1 22 35 19 2000 Synthetic oils have better resistance to thermal breakdown than petroleum based oils which is important in small displacement high revving engines like ours synths work almost as well under high heat as when relatively cool while fossil oils can turn to goo There are more advantages Synthetic oil has better residual properties it clings to engine components better than fossil oils more cohesive which means cold clutch plates are less likely to stick Synth oils get to cold engine parts faster than fossil oils which means less damage at startup And because of the better synth cohesive properties those componen
17. Ninjette so 105 much why deal with the expense of the Bandit the lower gas mileage the wearing out of tires chains my driving record can hear myself saying Well a smaller bike makes me a better rider don t need more horsepower On a twisty road that bike is all need Even for commuting that bike is faster than almost every car on the road Then hear the other voice sneering Well you guys with smaller bikes always say that Waitaminnit Who said that know where the first statement came from It came from my head thought it It was rational It made sense So if the Ninjette came from the head the thinking one where did the other oh Know Know exactly where it came from Sometimes you think with your head and sometimes you think with your Horsepower does that to you So does liquor The thing is know my talk of the Ninjette sounds a lot like a smallish endowed man making excuses for the lack of personal equipment by touting his skills However he makes some sense even to the pulse of my heart There is a ring of truth to the allure of a small bike Notice the last number in the comparison The Ninjette gets 70 miles a gallon no matter how hard you flog it put 15 000 miles on that bike and it never returned less than seventy miles per gallon A set of tires lasted me 14 000 miles paid 3 000 00 for that bike brand new It is often said that motorcycles are cheaper than cars Most of the
18. Wet Multi disc Manual Cable actuated Tubular Diamond design 27 degrees 3 3 in Hydraulic telescopic fork UNI TRAK system with single shock 55 1 in 5 5 in 5 1 in 100 80x16 130 80x16 Single hydraulic disc 80 1 in 28 0 in 43 1 in 6 1 in 29 3 In 304 355 Ibs 340 Ibs 4 8 gal Min 91 Research 87 Avg Octane Unleaded 1 9 liter Oil type SE SG Class SAE 10W40 20W50 Performance Stats 5 75 sec 14 6 sec 88 mph 105 mph 170 km h 36 11000 RPM 26 rear wheel 18 Ft Lbs 10000 RPM 14 rear wheel 55 75 MPG 13 Dyno Chart Kawasaki Ninja 250 Dyno 45 6 7 B 9 0 11 L213 be Engine RPM x1000 What Colors Are Available Yellow Purple 02 03 Green Black 02 03 Blue Black 03 Red Purple 97 98 00 Black Blue 93 96 14 Where can find more info Ninja 250 Riders Club Kawasaki Ninja 250 Discussion Board Ninja 250 Resources Ninja 250 Info Page Official Kawasaki Ninja Site Motorcycle Online review Kawasaki Vehicle Information Site want to know more about motorcycling in general I want to get a bike but I don t know the process Gazoo Thu Nov 25 23 41 28 1999 The order of events that got me riding was e MSF course e Motorcycle permit DMV waives riding section with MSF course completion at least in Virginia e Insurance call and pay initial fee by credit card and give
19. a hardware store that would do the same thing Can ride my bike home if the clutch cable breaks Duke Thu Jul 20 20 38 26 2000 Try pulling the clutch lever in to deactivate the starter cutoff switch Then hit the starter and the bike will begin rolling as it hopefully fires up Try this in second gear Once you have it going you can ride it home it is possible to shift gears without the clutch if you sharply let off the gas while upshifting or blip the throttle while downshifting When you get home hit the kill switch to stop Do this very carefully and remember you can t stop without the kill switch need to fix some accident damage need to realign my forks and front wheel Leon Mon Oct 9 11 38 2000 I ve just realigned forks by eye ball If they re a little crooked it doesn t seem to affect the handling much just put the bike on the centerstand and loosened the fork bolts slightly Then from the front held the front tire with my legs and twisted the handlebars straight Then checked to see if it was straight by straddling the bike and looking at the front tire and bars After a couple of tries got it to where it looked pretty good and just tightened the fork bolts up again The handlebar caps should keep the forks in about the right place so it shouldn t be very hard to do this 71 need to repair a cracked fairing Robert FriJan 14 11 40 59 2000 had really broken fairing on an 86 The right turn signal
20. buy them on line US Cavalry lists them in their catalog at 115 www uscav com 800 777 7172 Be aware that there is a Corcoran IlI Field Boot which has speed laces otherwise the styling is very nearly the same 130 from US Cavalry These are very good tough looking boots that will take a lot of abuse however they are not purpose made for motorcycle riders The original boot has a small ridge tread which may slip if you put your foot down the field boot has a much deeper tread which may make it less slippery The original boot has laces and unless you buy a zipper lace insert can take a few minutes to put on and take off though the field boot with speed laces is faster Neither of these boots have steel toes though there are other brands that do In my opinion the biggest problem these boots have is that they do not have the kind of protection extra padding gel packs hard plastic ankle shin heel armor etc that purpose made motorcycle boots have such as Alpinestars Dainese AGV etc Other Rain gear gabe846 Fri Aug 4 12 28 49 2000 Who says no riding in the rain love riding in the rain You learn a lot about braking and leaning and it s fun to look at cagers staring at the idiot on his bike in the rain It s important to have good gear to wear if you re riding in the rain When your crotch feet and hands are soaking wet your muscles cramp and shiver which is bad for being smooth with the controls which is wha
21. check the starter button itself If the contacts in the starter button itself are blackened corroded clean them off have seen this happen in other Ninjas A pencil eraser works well for this There are many other possibilities but these are three good ones My bike tries to start but won t no matter how much choke give it Duke Tue Feb 29 14 32 49 2000 It s possibly flooded mine has done this also Floods on a warm day with too much choke and then turns over but doesn t start After cranking for a few seconds it will sometimes sputter just a bit and a bluish white smoke will come out of the pipe but still won t start Try cranking a couple times in 5 second bursts with no throttle Then as you are cranking hold the start button and simultaneously add choke slowly until it fires when mine does this it starts up with maybe 1 2 choke any more less and it wont start Be careful you are not running your starter for more than about 15 seconds at a time or you may damage it On warm days normally crank it for a second or two with no choke and no throttle to clear any raw fuel sitting in there before adding choke it usually starts with no choke if it s over 70 degrees If you are still having problems you may want to take a closer look at your choke plungers Make sure they aren t sticking Also check your float valves to make sure your float bowls aren t overflowing which may also flood your engine My bike tries to start but
22. choices for Ninja 250 pistons 1 Stock Kawasaki pistons 2 0 5mm Kawasaki pistons 3 lmm pistons available through G Force You can also use Cosworth 2mm pistons but they are illegal for production racing and make the cylinder walls really thin so if the wrist pin comes loose it can work it s way through the cylinder wall and suck in a bunch of water and actually bought the bike with 2mm pistons in it back in 96 didnt know at the time and raced it that way for about 1 year before it blew up and built it to production spec How much work is involved when rebuilding Paul 311 Tue Oct 9 12 54 44 2001 The top end part of the rebuild is mostly labor usually pop the valves out run them on a wire wheel to get the carbon off clean out the exhaust ports and combustion chambers then lap the valves back In It s a lot of work G Force did the original valve job and I ve been using the same valves and seats since bought the bike in 1996 Their porting work is amazing The biggest increase in hp you re ever going to see out of a Ninja 250 comes from good porting and then selecting the right main jet 65 soend way too much time doing rebuilds because I m totally anal about getting everything clean and making sure all the gasket surfaces are pristine Saves a lot of time chasing leaks later can take a raceable race bike drop the motor and strip it down to the main bearings in about 2 5 hours Then spend about 4 solid w
23. collarless vest has a higher neck than the old one had Boots Are boots really necessary Brandon Scott Sat Feb 19 19 19 10 2000 The answer to this question is simple Do you need your feet amp ankles Quality boots provide a good deal of protection for riding and the possibility of going down have a friend who almost lost his foot due to a retread coming off an 18 wheeler and hitting his foot at speed He was wearing sneakers at the time Since then he only wears boots when he rides personally use western horse riding boots with rubber soles They are relatively cheap approx 100 00 and can be worn with all types of clothes They also provide the protection want What are some models to consider Alpine Stars Barry Mon Feb 21 12 18 45 2000 It s been several years since last bought boots so my info as to what models are available is probably out of date however when shopping for boots started by looking at the brands the top riders wear In my opinion AlpineStars is the brand worn most often There used to be three models with increasing price GPS GP Pro and GP Tech about 180 225 250 respectively The big accessories houses all carry them The Tech has gel pads over the ankles have both the Pro and the 18 Tech neither are all that comfortable for doing a lot of walking around in but I ve the impression that most sport boots arent The biggest hassle with these boots is that they are all mad
24. completely Repeat this time revving gently more as the temperature increases Shut down cool off Repeat this time riding the bike gently Shut down change the oil cool off Take the bike for ride again pushing it harder this time start exploring the upper half of the tach Never push it until it has warmed up bit Repeat this cycle several times each time pushing the motor harder Try out the redline for a moment here and there you won t hurt it Change the oil after another half dozen runs Then ride as you would like but always being more gentle on the machine until it is warmed up and ready for the abuse that Kawasaki s are famous for taking Again this is my take on the issue how to break in a motor well without breaking it Do your research and decide what is best for you and your machine How long do I have to wait before switching to synthetic oil Duke Wed May 17 22 46 04 2000 put about 700 miles on my new rings before changing to synthetic oil and it began to burn oil like crazy was burning nearly a quart every 500 miles I ve now switched back to mineral oil and the oil consumption has slowed way down I m at about 1 000 miles and I ve only gone through about 3 4 quart This bike as is the case with most modern bikes takes a good long while to get everything seated I ve heard mechanics say to never go to synth oil before 5 000 miles Won t hurt anything but you ll wind up burning more oil than you should and pa
25. doing this the temperature needle goes over the mid point while riding use a smaller piece of cardboard How far can I go after putting the fuel petcock on reserve Leon Sun Aug 6 03 09 34 2000 usually get 35 to 50 miles on reserve Reserve should be used frequently When the petcock is switched from main to reserve the fuel that goes to the engine comes from a lower part of the tank The lowest part of the tank is where the water and dirt go if left alone If the reserve is never used the level of the water and dirt in the bottom of the tank continually rises If it gets above the level of the reserve fuel line it goes into the carbs when the petcock Is switched Personally prefer to have a little water and dirt go into my carbs every tank of fuel rather than a lot of it at a time when I m already in trouble because let the fuel level get a lot lower than normal think this is one of those messages that needs a disclaimer Don t do this with your own bike dirt and water shouldn t be put into the carbs The correct method is to remove the tank remove the petcock then completely drain and rinse the tank This should be done more frequently if the bike is stored outside where it gets rained on Dispose of contaminated fuel in accordance with local laws What kind of fuel should I use Leff Sun Aug 6 21 26 36 2000 The owner s manual suggests using 87 octane unleaded gasoline Having too high an octane is never harmful but hav
26. exactly what you and your bike can and cannot do in a reasonably safe place where you don t have to worry about oncoming traffic or gravel Most riders who haven t done any track time really have no idea of just how hard a motorcycle can corner very before the tires actually do lose traction Accelerating Changing Gears Upshifting Jeb Mon Aug 7 14 57 36 2000 You can shift anywhere from 5 to 13k depending on how fast you re going accelerating If you re poking along behind a grocery getter from a stop light a shift point of 5 or 6k makes sense If you re accelerating normally and want a good compromise between performance and fuel efficiency shift around 8 10k If you re trying to quiet the rowdy kids next to you in daddy s 318i cook it up to 13k before hitting the next gear Cruising revs should be between 4 10k Downshifting Jeb Tue May 30 20 34 36 2000 There are two kinds of downshifting downshifting to slow down and downshifting to speed up When slowing down you should ride your current gear to about 4k then quickly kick it down as you pull in the clutch and blip quickly open a bit the throttle this will bring the revs back up to about 4500 which you can again ride down a bit before going down to a lower gear Using this method you can stop more quickly and will not encounter a jolt When I slow down from 60 mph kick down a gear every few seconds until I m in 3rd at which point I m usually doing about 10 mph or l
27. feet not counting reaction time Note that think these are good distances don t get frustrated and lock up the front brake trying to achieve them Trail braking VFR Pilot Tue Jul 10 13 10 44 2001 It s perfectly possible to brake safely while leaned over and to do so without the bike straightening up but you have to practice doing this before that sudden emergency pops up if it s not second nature it s not going to happen when you most need it The trick is to countersteer as you brake so that the bike remains balanced at the same angle as before you applied the brakes You practice this by finding an empty road and applying the front brake gently and smoothly as you go around the curves After you ve done it for a while you will find that you begin to automatically add more lean as you add more brake When it begins to feel more natural start hitting the brakes a bit harder and faster until you can bring the speed down quickly without the bike suddenly heading straight for the outside guard rail Note that there are times and places where trail braking can put you on your head If you are already at full lean suddenly hitting the brakes will probably cause a lowside and so can hitting a patch of frost or moisture On the other hand trail braking can save your bacon came around a blind corner last summer to find the road full of spinning cars and a motorhome sideways across both lanes got stopped with just about thre
28. for about 30 45 minutes and see how you feel Or go find a used 250 and take it on a test ride 10 Am I too small for this motorcycle Duke Sun May 14 17 38 31 2000 I m only about 5 2 and don t have a problem even though can only touch the ground with the ends of my toes Once you get a feel for the balance of the bike it s not hard to keep everything upright Only place have trouble is pushing the bike backwards in a parking lot Usually just walk the bike beside it to where can get on and get going How does the EX500 compare to the EX250 Craig M Mon May 22 10 23 29 2000 have both the EX250 and the EX500 both are Y2K models The 250 is a screamer that performs well and can easily get me into trouble My only complaints about the 250 are the excessive nose dive when getting on the front brake hard and the skittishness of the rear during high speed cornering Both are easily corrected with suspension adjustments I ve just been too lazy to get the parts and do the work A bit more wind protection would be great too The 500 addresses these problems the diving of the front end to a degree the rear s skittishness and the wind protection A plus for the 500 is the greater torque and power off the line it pulls stronger in my opinion and will get you into illegal speed territory just a bit quicker than the 250 With greater weight is has more stability in high speed and windy situations Insurance is just about the
29. from the brake line put your fingers between the caliper or apply the brake with the caliper removed Remove the two bolts holding the caliper to the bike and remove the caliper Use a C clamp to compress the pistons If you don t have a clamp you can use a small wrench wrap a cloth around it and insert it into the caliper between the two used pads gently apply pressure down toward the two pistons prying the caliper apart Now you to easily remove the used pads and fit it back onto the brake rotor back with the new pads in place Turn the caliper upside down The small pad will probably fall right out the larger pad you may have to work off the retaining posts as there is little room between the ends of those posts and the caliper claw Installation is a snap Put the large pad on the retaining posts then place the small pad against the pistons and nestle it into the defined spot Slide the caliper back onto the disc and line up the bolts to the caliper holes The bolts don t need much torque to seat them What replacement pads should consider lim Race Wed Mar 7 02 33 23 2001 The stock pads aren t too bad Until they become bad They tend to fade really fast Don t race on them if you can help it Galfer greens are nice and a good excursion into improved braking found they were very progressive in that increased level pressure was very measured in the way the brakes grabbed EBC HH s are braking overkill Grab
30. good thing The Ninja 250 is pretty light on the front end and will tend to push the front end with the stock ride height Raising the rear a little or dropping the front a little helps cure this Unfortunately ride height is a relative thing so set up Is difficult to translate from bike to bike and will be affected by things such as a sag which can be adjusted by changing preload b position of the forks in the triple clamps C tire profile d longer or shorter rear shock Preload is what you change to set the sag Checking sag is one way to determine if you are using the middle of the available travel on your shock forks The middle range in the travel tends to give the most even damping from what I hear and it will also help keep you from topping out or bottoming out if you have the sag set correctly I d like to improve my bike for touring Leon Mon Jan 22 07 58 52 2001 My longest days on the 250 exceed 1500 miles I ve exceeded 1000 miles in 24 hours about a dozen times www saddlesore com ssbbfin htm search for Ninja 250 My Ninja 250 is at 97K miles it will be within 10 miles of 100K at the Kawasaki Tent in Daytona on Saturday of Bike Week I ve modified my ninja especially for long distance touring Windscreen had good luck this weekend using Lexan and using the mirror mounts and bottom row of the stock windscreen bolts Handlebars For a touring bike you should sit on the seat and without leaning forward reac
31. his CBR 600 slid into a guard rail and flipped up into a concrete bridge pylon He suffered a broken pelvis several broken ribs and major bruising He was wearing jeans a leather jacket and a helmet If he wouldn t have been wearing his gear he would have been dead close to it as it was He has recovered somewhat and can now walk with a cane but has a hard time sitting up for over an hour The moral here You can still get hurt even with gear in a Slow speed accident be careful but the gear saved his life and kept him from losing any skin Riding again after an accident lan Mon Sep 3 18 47 53 2001 l ve been cruising around on motorcycles for the better part of the last ten years and let me tell you this 112 You have to take the good with the bad Its going to rain sometimes A deer might decide that the berries on the other side of your street taste better God knows car drivers are going to do stupid things around you on a regular basis And to top it off you are going to make mistakes Some mistakes aren t too much to sweat over You missed your exit so take the next one Some mistakes might just scare the daylights out of you You caught the exit but you were going way too fast and wound up on the grass at 60 miles an hour I did that one the very day got my magna 4 years ago And sometimes mistakes might mean you get hurt but that one you already know Learn from tt But the worst possible mistake is to give
32. know more about the Ninja 250 motorcycle What is a Ninja 250 Jeb Thu Nov 11 3 48 42 1999 The Kawasaki Ninja 250R or EX250 GPX250 is the smallest in Kawi s rather large line of sportbikes both in weight and displacement First released as the E in 1986 then the F after a redesign in 88 it has remained largely unchanged to this day The 250 is a light quick bike which the experienced rider can reap much performance from Still it is designed in its stock configuration with the beginner in mind and is tuned to be easily manageable it is a bike that grows with its rider Emphasis with this Ninja is placed on its excellent handling characteristics and reliability and less on acceleration and contemporary design While the 250R is the only sport bike available in its class in the United States it well fulfils the need for a bike in that class It has acquired and retained a faithful following of those who desire a fast crisp ride but don t require the high torque of a larger displacement bike With an MSRP of only 2999 easy maintenance excellent fuel economy and insurance premiums among the lowest in the market the Ninja 250 is full featured motorcycle that is easily accessible to any wanting to ride What kind of performance can I expect out of it Chris Tue Nov 9 14 38 13 1999 I m 17 and I ve been riding my Ninja 250 for about a year my first bike as well had some limited experience on a Honda 400 prior to my MSF cl
33. let it empty all the while avoiding any spillage brake juice is corrosive and quickly wiping washing any surfaces hands that are contaminated don t let fluid contact the brake disc or pads Open the reservoir cap and remove secondary cap and rubber seal fill with the reservoir with fluid to fill the brake line you must repeat the following sequence at least 20 30 times open the bleeder valve squeeze the brake lever close the bleeder valve release the brake lever This process allows the fluid to enter the line but not let the vacuum retract it again Slowly line pressure is re established and eventually the fluid will begin to exit the valve again Now you can do what you ultimately wanted to do in the first place bleed the line this isn t hard at all With the valve closed pump the brake to establish pressure then quickly open and close the valve to bleed it repeat You basically just keep feeding fluid through the line until no air bubbles are seen exiting the line with it anymore Tightly seal the reservoir cap and bleeder valve to deter air entry Repeat above for rear brake my rear brake took half the time of the front You should notice improved lever pedal feel and your stopping distances should decrease as well How do I replace the brake pads Jeb Wed Aug 16 21 21 25 2000 This is a pretty straightforward job but you need to be careful with the brake caliper Do not drop the caliper suspend the caliper
34. ll hear two loud and distinct POPs one for each bead 3 If that didn t work don t sweat it Use a ratcheting tiedow compress the tire down into the rim this will force the beads towards the lips Repeat step 1 above 4 If that didnt work put your tail between your legs and go beg the shop to do it for you While your there ask them to balance they ll probably do both for a couple of bucks 5 Balance the tire whole other tutorial Or ask the shop to do it Congrats Now reinstall the tire exact reverse of above Be sure to use a new cotter pin How can I balance the tires by myself Jeb Fri Nov 30 21 28 38 2001 Static balancing balancing without a machine isn t hard but can be a little time consuming 63 The first step to balancing the tire is to mount it in the proper position There should be a paint spot on one of the sidewalls this is the lightest point on the tire per the manufacturer The heaviest point on the wheel is usually where the valve stem is So when mounting a tire if the paint mark is positioned next to the valve it s likely the balancing will already be pretty darn close After seating and inflating the tire then just mount the wheel loosely on the bike and spin the wheel several times noting each time where it comes to rest If it stops in random places each time the tire is balanced if it repeatedly stops at the same place each time a wheel weight needs to be affixed I have a strip of
35. lube and a handful of old rags to clean my chain First put the bike on the centerstand and make sure it s in neutral The engine is not running and the pipes should be cool to the touch Then rotate the rear wheel by hand spraying a liberal amount of WD40 onto the exposed section of the chain as you go I hold a mask cut from scrap cardboard behind the chain while spray to prevent getting WD40 all over the rest of the bike and the rear disc in particular In fact if you do this over pavement you ll also want to put down a bunch of old newspapers to absorb the runoff Otherwise you end up with WD40 everywhere Once the chain has been soaked keep rotating the rear wheel and wipe the chain down thoroughly and repeatedly with the old cotton rags getting off all of the dirt that you can This is really messy takes a while and you should plan on tossing the rags when you get done And washing your hands for about an hour Try not to catch your thumb between the chain and the rear sprocket more than once or twice as it really hurts d Once the chain is clean sort of and dry spray on the chain lube again using the cardboard mask to keep the lube more or less where you want it Let bike stand for a few minutes and then go ride You will hear some people tell you that the world will end and your bike will probably rape the neighborhood children if you let WD40 come anywhere close to it All can say is that I ve used it to cl
36. makes a 1pc Spark suit for 349 in Motorcycle Accessory Warehouse www accwhse com A better suit would be the 2pc Fieldsheer X speed for 599 from New Enough www newenough com You can find pretty cheap leathers in a lot of places but most of them don t have good ventilation The Spark suit doesnt have that good of ventilation but the X speed has plenty of it If buy a leather suit its definitely going to be a Fieldsheer you can t beat it for the money As far as textiles First Gear makes some pretty good stuff that doesn t cost an arm and a leg J oe Rocket would be another option First Gear s site is www intersportfashions com and J oe Rocket s site is www joerocket com Back protector gabe846 Wed Apr 26 22 34 58 2000 The point of a back protector is to protect your spine and ribs from hard blows The point of a hard shell is to disperse the force of impact much like the shell of your helmet Too bad the US is too backwards to have any kind of standards for back protectors Luckily the European Union EU has a standard for motorcycle armor called the CE standard You can buy CE rated back protectors in the states and recommend it That Dianese 7 plate thing with the flimsy foam isn t worth shit as is the junk that comes with Firstgear jackets and suits 20 Make sure the back protector covers more than just your spine remember it s for the ribs too Also consider wearing a chest protector as well Knox is a
37. melt They valves need to fully contact the valve seats to get rid of some of the intense heat through conduction that builds up in them or they re toast Many engines are just the opposite in the fact that clearances get looser and start to make more noise because the parts listed above are reversed as far as wear rates are concerned 43 What is the adjustment procedure Jeb Sun Apr 22 21 53 40 2001 Put the bike on centerstand Take off the lower and upper fairing side covers and fuel tank Carefully pull the spark plug wires by their boots and remove the left and right coil packs two 12mm bolts each The service manual suggests draining the coolant so the radiator can be removed to make it easier to reach the exhaust valves but it is possible to avoid this also remove the wings from which the front of the engine is hung one long 14 mm bolt which makes it much easier to reach the exhaust valves re eee PEE E EEEE Remove the alternator cover and flywheel view cap on the left engine side cover use a very large flathead screwdriver Take off the four valve cover bolts and lift the O top end Using a torque lever large socket driver turn the y valve cover do not remove the cover gasket leave it on the engine using the alternator bolt inside the left cover housing siii Loft side of engine turn the bar forward counter clockwise until the cam lobes i LA S over the left cylinder cam lobes point out
38. missed in the corners There where you are full lean left then upright a little front brake then full lean right then upright then well you get the idea On those corners knew the Bandit was there had to press the bars right then left leaning it onto corners could feel the suspension working to keep a 600lb bike and 200lb rider in check over the somewhat frequent mid corner bumps and ripples On those corners know the Ninjette would have been almost unnoticeable under me would have been concentrating more on the road and less on what the bike was doing rode the Ninjette at a SIR track day last year and that bike just disappeared beneath me All that was left was me and the track turning this way and that felt more like a runner more like a bicyclist connected to the asphalt On that bike would have ridden a better ride to Windy Ridge and a better ride back down think would have been cornering better late apexing as should would have been smoother on the throttle keeping the bike more stable and arching though the turns better would have kept my cornering speeds higher and the lines would have been cleaner Less horsepower does that at least for me On the twisty stuff become a better rider have no doubt if there were another me that day riding the Ninjette the Bandit would be the second bike to the top So why the size thing then Why do own a Bandit 1200 and a Ninjette 250 If love the
39. next outer pair and the next until each pair of bolts is snug but not tight the screen needs some slack to flex If you tighten the bolts too quickly in the wrong order or too tightly you risk cracking the screen I want to improve the appearance of my lights want to wire extra brake lights into those empty rear sockets ITM Sat Feb 12 15 46 22 2000 It s very easy to do It s also a good idea to add extra brake lights as well in the case that your one and only brake light goes out Makes you more noticeable when stopped with your brakes on e Goto autozone and pick up a couple of double contact sockets part 85803 made by conduct tite e Runa ground wire to each socket solder or tape in place e Runa power wire from each socket to the brake light circuit and accessory or tail light circuit wires blue and red It s very simple to do It s cheap probably under 6 and it makes the back of the bike look bigger gets rid of that old small moped look want to replace the front flasher pods with flush mounted units Jeb Sat Mar 18 11 20 49 2000 have the Lockhart Phillips signals model 122 9900 these fit the fairing recess better than the other units they offer You can order them from the LP website or probably find them at a local bike shop got them for 20 Duke has some units he got from Autozone for about 10 that are actually Ford truck marker lamps they don t look bad either Here are two pics I took of t
40. on the rear Jeb Sat Nov 3 11 39 09 2001 The Ninja 250 s rear rim was designed for a 120 width tire the EX250 E model came stock with a now discontinued Dunlop K530 120 80 rear tire The EX250 F 1988 model however has the same size rim but comes stock with a Dunlop K630 130 80 tire mounted Kawasaki actually put a wider tire on their own rim than is ideal for the wheel width the 130 is slightly pinched in the rim while the 120 is right at home The 120 80 tire is better than a 130 90 usual rear stock replacement in many ways First off the 120 80 tire typically weighs four pounds less than a 130 90 of the same model This means less dead weight on the chassis less rotating mass for the engine to turn less unsprung weight for the suspension to carry The lower profile is also more rigid The tire width is the ideal size for the 2 5 inch wide rear rim so the contact patch may be better depending on the model while a quicker steering response is effected The bead to tread height of a 120 80 tire and a 100 90 usual front stock replacement is almost identical which makes it a great rear front size combo The 120 80 tire also just looks better on the rim than a huge 130 90 in my opinion Why some people think a bigger rear tire makes the bike look bigger don t understand a bigger tire should technically make the bike itself appear smaller by comparison Downsides to using the 120 80 include a loss in final gearing 3 les
41. out there some good some bad and some hazardous Try them with caution they may damage finishes or penetrate into seals where you don t want them 57 How do service the tires What tire pressures should use What tire pressures should use for everyday riding Wes Tue Aug 1 05 06 58 2000 For normal use Dunlop recommends 30 34 for the stock K630s on our bikes but have no recommendations for the K591s That said they do recommend 30 34 for the EX500 K591s so doubt you Can go wrong ran 28 32 as the owner s manual suggests for a while but like the higher pressure better it makes it easier to cross cheese grater bridges not get stuck in pavement snakes etc What tire pressures should use for touring high speed riding etc Joe Mon Jul 31 19 37 54 2000 Here s what Dunlop s web site says For high speed fully loaded or dual riding touring motorcycle applications inflate front tires to maximum recommended by vehicle manufacturer for Dunlop fitment and rear tires to maximum load inflation pressure on sidewall Rear touring tires must be inflated to a minimum of 36 psi for light to medium loads and 40 psi for dual riding and other loads Never exceed maximum load indicated on tire sidewall or vehicle capacity load found in owner s manual How often should I replace the tires Leon Wed Jun 7 19 07 04 2000 It depends on how hard you ride I ve heard that some of the racers replace tires after only a
42. possible which also produces the most power The problem is denser air Cold Dry produces a leaner condition and thinner air hot wet produces a richer condition The other problem is that the weather is constantly changing So in the end yes you can constantly chase the perfect mixture thus the advantage of fuel injection which is constantly adjusting for weather or you compromise and set up the jetting to work well at about 70 degrees a happy medium A lean condition can hurt your engine over time but you would certainly know it s lean spitting sputtering etc ran 92 mains in my carbs for a long time and had no problems until pulled my airbox top allowing more air to flow thus creating a leaner condition and could immediately tell it was too lean 105 s stock are in it now and it runs very well Why did I pull my airbox lid Why do people use K amp N pods More air in more 02 in more gas in more power 53 How do I check change coolant How do I check the coolant level Thundercat Wed Dec 8 16 41 23 1999 Your coolant tank will have two marks on it a low or cold level and a high or hot level When the bike is cold has not been run the coolant level should be no lower than the low cold level When the bike is hot just been shut off after a significant ride the coolant level should be no higher than the high hot level This is a normal operating range coolant level will fluctuate as it expands contrac
43. price of a new 250 However if what you really want is to be able to go faster then learn to ride better 91 Functional Ergonomics want to adjust the ride height of my bike How do I change the ride height Adjustment Tech Racing Kit Ninja Grrrl Mon Nov 1 11 14 32 1999 Thundercat installed adjustable links to my bike s swingarm The suspension links are from Adjustment Tech Racing and cost about 229 00 US funds First we made sure the lengths of the links are set equally With the bike on the centerstand and tension off the rear wheel we removed the stock dogbones and installed the new links torqued everything to spec then sat on the bike while he adjusted the links incrementally until found the right height about 1 1 8 lower We found that the kickstand had to be shortened to get the bike to rest at a safe lean A spirited shakedown ride 215 miles Thundercat piloting revealed the bike to be stable and well mannered Adj ustment Tech Racing RR 3 Omemee Ontario KOL 2WO Canada 705 799 5139 http www3 sympatico ca a jones RHA HTM Changing fork position Skip Sat Jul 21 13 24 11 2001 The front can be lowered by sliding up the fork tubes in the triple clamp You can leave the handlebars on and loosen the four two upper two lower fork clamp bolts to drop the front end several millimeters the forks will top out at the bottom of the handlebars and then the clamps can be retightened upper cl
44. rear axle to some fixed location on rear such as bottom of cowl at joint in plastic Then get it off the stand and sit on it in full riding gear and make the same measurement again Subtract the second from the first to get sag Adjust the shock to get 1 1 4 to 1 3 4 inches sag 1 4 to 1 3 of full shock travel You see it all depends on your weight Also helps to have someone else measure for you so you can get your feet up to get true riding position Also jiggle bike with you on it to get accurate reading after suspension is unstuck You can adjust the preload by loosening the preload locknut or ring then turn the adjusting nut ring with a suitable spanner or tapping it with a screwdriver using a mallet to rotate the piece What kind of shocks are available for the 250R Paul 311 Mon Jan 3 12 44 37 2000 Fox makes some of the best racing shocks They are adjustable for rebound compression preload and sometimes even ride height Fox won t make them anymore so there are a limited number of them on the used market They seem to go for 300 500 on the used market I m working with Aftershocks of Palo Alto to develop an Ohlins shock which will have all of the features of the Fox and have custom valving by Aftershocks should get to try one in the next month or so I ll report back on the results The only high end shock you can buy for the Ninja right now is the Penske shock It starts at 700 to 1 200 78 would guess t
45. removed take the allen bolt out of the bottom of the tube Be careful not to strip this bolt as it is very tight There should be a copper washer seal with this bolt You may need to stick a wooden dowel or handle down the tube to hold the inner part of the fork from moving did it without this After removing the allen bolt the inner fork assembly will slide out rod thingy amp spring Remove the rubber dust cover from the top of the black portion of the tube using a small screwdriver Remove the clip above the fork seal using a screwdriver Now you need to pull the tube out of the shock Hold onto the silver tube part with the black shock part facing down and pull up and down with a rapid jerking motion The black portion of the shock should move freely up and down with each jerk Keep doing this until the black shock portion falls to the floor May wanna put a towel down to protect it when it falls The small tube that completes the rest of the inner shock should now be free inside the black shock portion After the removing the silver tube the fork seal should now be on it Remove it by hand and clean everything up using a lint free towel Check the fork tube and guide bushings for damage scratches If there are any scratches or nicks on the fork tube sand them smooth with very fine grit sandpaper 1500 grit Sand in an up and down motion If there are major gashes in the tubes or the bushings look damaged replace them
46. s the springs replace them If it s the basket file it smooth take it out of the bike when you do this you don t want the aluminum filings in the motor It s probably not the clutch plates or steel plates these should last as long as the engine if not abused How should I clean the bike Ninja Grrrl Tue Dec 7 08 40 03 1999 You can easily clean you bike with a garden hose just make sure you don t use too much pressure Don t be afraid to wet it down good just dont concentrate the spray on the switches wiring or airbox Hose it all down then with a clean mit wash it from the top down with car wash detergent Never use dishwashing liquid or any other detergent formulated to cut grease it will cause deterioration of the natural oils found in your tires hoses and seals causing them to become brittle and wear out faster For dirtier areas like wheels chain guard swing arm kick stand etc use an older wash mit using your good one might contaminate it with grit Rinse the bike thoroughly and dry it with a chamois real or synthetic It doesn t hurt to run the bike for a few minutes either to better dry it out A good coat of wax will help protect the painted surfaces as well as the polished chromed and glass also wax the windscreen but don t wax any textured plastic like the mirrors or rear fender it s hard to remove use Eagle One wax be careful some waxes may be too abrasive There are a lot of specific cleaners
47. shop resurface the rotor ever so slightly as to not make it too thin If all else fails replace the rotor My brake pads are grinding RoadOfTheDevil Sat Apr 28 22 19 05 2001 It is normal for the pads to drag slightly especially just after replacing them Excessive grinding can be caused by having the torque link nut too tight or having the hex nuts that hold the caliper to the caliper mounting bracket too tight Be sure to correct this before the rotor warps from being overheated My handlebars shudder when l ride What should check for this problem Gabe846 Fri May 26 19 34 44 2000 At low speeds this is normal but at high speeds not so much Here s some things to check e Steering head bearings too tight or loose or worn out e Tire wear or pressure e Alignment of front and rear wheel 70 e Bent triple clamps or forks What if steering head bearings are bad Leon Mon Jul 31 15 01 07 2000 If the bearings are too loose you get a wobble If too tight then when going around a long curve the bike wants to turn then straighten and repeat rather than taking a smooth arc If there s no wobble then tightening the bearings probably won t make much difference I ve ridden with marginal bearings for quite a while To adjust them and look for worn bearings put the bike on the centerstand and put something under the engine to get the front wheel off the ground First try to move the fork legs forward and back if ther
48. shop the guy with the spray gun moving the entire length of the car without stopping that s what your going for Be sure to overlap the passes but dont spray too long or too slow in any one spot or else drips and runs will form If they do let the paint dry a bit beyond being tacky and wet sand the run off Apply 4 6 coats of paint After you got the paint exactly how you want it you need to seal it using clear coat If there are any problems with the paint now is the time to fix it Apply the clear coat in the same manner as the paint Apply 5 7 coats Plastic parts don t need to be buffed the way metal parts do like gas tanks so never had to do anything like that Any automotive site should have articles on how to paint metal and get an excellent mirror finish A few final things the wet dry paper Use your judgment on what grade to use You could use 3000 grade to take off the clear coat and paint but it ll take three years And likewise don t use 500 grade when your almost done with the primer coats The better the final level of primer is the better the paint job will look As with any painting use in a well ventilated space free of airborne particles ie dirt saw dust mosquitoes and passerby s wandering fingers Your best bet is to find something lying around that s made of hard plastic and is painted to practice on had a bunch of Starship Trooper popcorn tubs from AMC that ruined before finally got it right If you re wor
49. straight guys but it s important for our riding partners of the fairer sex Lastly buy the cheapest gear that meets all the above requirements Don t buy stuff from third world countries if you can avoid it almost all the stuff I ve seen from China Pakistan India and Malaysia sorry if Malasia isn t 3rd world is pathetically shoddy and falls apart after a season or two Japanese American and European made stuff is more expensive but only by about 20 30 It s worth it since you only have to buy well made stuff every 10 years instead of cheap stuff every two What do need to know about insurance How much is insurance going to cost me for the Ninja 250 Barry Sun Nov 28 21 35 08 1999 Insurance cost depends on a lot of things age state driving history bike etc etc Also in my Opinion some companies just don t like to cover riders with certain profiles even if they are good otherwise so they price their coverage outrageously high guess a good price would be something like 300US for six months but have heard of guys being quoted as much as 4000US a year Get a cycle magazine and look for the ads from Insurance companies all of them have 800 numbers and give them a call When you talk to them ask about coverage for an EX250 if you call it a Ninja they might put you in with the bigger sport bikes and that can cost big The bright side is that the Ninja 250 will be cheaper to insure than any other sport bike a
50. t feel it I ve been using it since about a year ago when set a 250 Production track record at Buttonwillow which for the moment still stands After that really couldn t bring myself to change anything that didn t have to change Rear end How do I change the rear shock DrBoom Thu May 23 23 27 51 2002 What you need e 19mm wrench Suitable ratchet 3 8 drive or larger 10mm socket 17mm socket 10 or longer extension bar for ratchet 2 or 3 Phillps screwdriver Straightish long prybar or suitable facsimile 6 zip ties Coolant optional Your new shock Put bike on center stand Remove seat Remove left side cover with Phillips screwdriver Move coolant reservoir out of the way by removing 2 10mm bolts Turn reservoir 180 degrees to your left and loosely secure it to whatever s handy with a zip tie Put Tl SS the 10mm bolts back into the holes they came from to avoid kicking them to oblivion when you get up to grab your beer 5 Working from the left side of the bike break the lower shock shackle bolt loose with the ratchet extension 17mm socket Once it s loosened up use the 19mm wrench to keep the nut on the other side from turning you won t be able to hold it with your fingers Once the nut is off wedge the prybar under the back tire and gently wiggle it up and down while pulling on the bolt head it should come out easily without trashing the threads Let the back tire rest on the ground 6 Stil
51. the WD 40 and spray a nice bit off it down the cable line you ll see a few drops exiting the clutch end when you ve given it enough Now squirt a little 3 in 1 oil into the same place you just doused w WD 40 Work the cable in and out of the sheath several times squirt more oil in there repeat Do this about 10 times Your clutch cable is now lubed it should not need another treatment for many months A well lubed cable should last 15k miles or more 56 How do I replace the clutch cable eon Sat Mar 25 17 18 53 2000 The first difficult item is threading the new cable into place where the old one was find this easiest to do if put the new one in place as remove the old one It also helps to remove the seat and fuel tank to see where it goes The other difficult part is adjusting the free play usually adjust it at the handlebars so it s about in the middle of it s adj ustment then use the two nuts down near the engine to set the initial free play That way there is plenty of movement in either direction at the handlebar end for later adj ustment How do I refurbish a slipping clutch Leon Fri Jul 5 09 51 12 2002 The consensus here is the springs go first If it s a high mileage bike the fingers on the basket might have some grooves worn in them Remove the clutch cover and see what s wrong have a new gasket on hand before doing this The manual has service lengths for the springs and thicknesses for the plates If it
52. the mid 90 s didn t stiffen up my stomach that much So did some searching for decent tires at a decent price The price needed to be the more important factor with quality being close behind wanted decent tires that would offer good wear stick and especially feedback after dealing with the stock rim protectors for so long did some searching around and liked the sound of the Pirelli Strada MT 68 69 series tire and ordered a set Unfortunately the place ordered from couldn t get the front tire anymore so just went with the rear and had them slap on a Bridgestone BT45 front for 1 more than the Pirelli would have cost Front tire size is a 100 90 16 and the rear is a 120 90 16 After a little difficulty mounting the tires and getting the beads to seat on the rear tire was off on new rubber First thing noticed right away after scrubbing the tires in is that the front end of the bike no longer feels like its just there You can actually get a feeling for what s going on between the front suspension and the ground Turns at speed became enjoyable instead of feeling like work didn t have to wonder if I m going to fast for the curve anymore because the tires are actually telling me what s going on down there put lots of miles on them in various different conditions Rain slow speed commuting fast speed commuting twisty mountain roads and everything in between They seem to be pretty decent in all conditions save snow d
53. the pipe it will rust Someone said you can clean the pipe periodically with steel wool but that would be too much maintenance for me I ve painted my pipes twice so far The first time used 5002 paint but a black plastic bag melted to it and made it look like crap The second time used 12002 paint It seems to hold up better Make sure you take your time when painting it Paint over the course of a couple of days and apply thin coats and the paint will stick better I want to remove the rear fender Jeb Fri Jul 28 21 38 36 2000 If you want to save some money you can cut the stock fender down to size to make it look cleaner Unbolt the fender mounts and remove the fender outline the new shape in chalk then take a dremel cutting tool to it and reshape as you like If you want to keep the stock signal flashers instead of integrating them into the tail you ll have to leave tabs for these on the side don t forget to leave a license plate tab If you want to keep it simple and make it look a little better you can order a fender eliminator kit from Competition Werkes The kit they sell looks good it is made of brushed stainless steel and has removable tabs for the license plate and signal pods I want a new windscreen What models colors are available Jeb Tue Aug 22 10 45 13 2000 When it comes to aftermarket windscreens there are two major brands to pick from Lockhart Phillips and Zero Gravity Targa also makes a windscr
54. them slide As far as the predictability of a slide drift I ve never really experienced much of a slide short of having low tire pressure at the Gap last weekend And even that front end push was not severe just enough to make me think was really sliding Point is the 630s are fine for all but the best of us They are also about 35 less expensive than other Dunlop tires Dunlop K591 Paul 311 Tue Feb 8 23 03 13 2000 On the race track there is no other choice in 16 tires but Dunlop K591 s Front 100 90 16 Rear 120 80 16 front tire or 130 90 16 There is no other combination of tires presently manufactured for 16 wheels which will work as well as these two tires They re cheap too don t have any sort of tire sponsorship so I m not trying to sell anyone Dunlops Every single Ninja 250 that races with the AFM runs Dunlop K591 s except for a couple people I ve seen running stock tires on their very first race weekend Dunlop GT501 Paul 311 Thu Sep 28 20 31 09 2000 The K591 s are now out of major production though will still be available for a while the GT501 s are their replacement Here s a quick second hand review Fast guy Robert Kennedy tested out the new Dunlop GT501 s at the track last weekend He thought they felt as good or better than 591 s and they also seemed to wear pretty well The smallest front is a 110 90 16 which required fender modification moved it up to keep it from dragging The choices for t
55. time especially today this is a myth a fallacy a rationalization Anyone ever add up the costs of a new bike counting purchase price tires every 3 000 miles valve adjustments chains gas mileage insurance helmets and riding gear Ever compare it to a car Do the math some time You may be surprised A 3 000 00 bike that needs only two services in 15 000 miles uses only one set of tires one chain and returns 70 miles a gallon does compete with the car You can have your cake and eat it too or you can think small Does your cake have to be bland Does your bike have to be slow What is slow How do you define slow This Bandit rider knows what slow is It s almost any bike or car that isn t my Bandit However that speed and that horsepower comes with many prices Those being either eternal vigilance or a quick trip into the back of a slower car or the side of a hill My right hand is connected to my destiny in a much more immediate fashion on the 1200 than on the 250 So is the 250 slow Someone will call it that I m sure Can it go on longer rides Some will say it cannot They should have followed me around the Cascades Loop a few years ago as led most of the way Is the Ninjette busy at speed Sure it is Does it matter Not when you get used to it What really matters is that it is fun In my ride up to Windy Ridge some of the corners weren t fun they were work on the Bandit They wouldn t have been on the Ninjette
56. tires fit the EX250 rims absolutely spot on 100 80 and 120 80 are what the wheels were designed for and steering response is awesome with them High speed straight line stability will not be quite as good as with a larger 100 90 amp 130 90 setup but turn in rate and agility will be better Pirelli Strada MT68 69 lan Wed May 14 09 39 20 2003 Last summer had surpassed 12k miles on the stock Dunlop K630 s and had completely killed the rear treadwise but the front could have kept going if could have stomached it Unfortunately working in McD s for 4 years as a manager back in the mid 90 s didn t stiffen up my stomach that much 59 So did some searching for decent tires at a decent price The price needed to be the more important factor with quality being close behind wanted decent tires that would offer good wear stick and especially feedback after dealing with the stock rim protectors for so long did some searching around and liked the sound of the Pirelli Strada MT 68 69 series tire and ordered a set Unfortunately the place ordered from couldn t get the front tire anymore so just went with the rear and had them slap on a Bridgestone BT45 front for 1 more than the Pirelli would have cost Front tire size is a 100 90 16 and the rear is a 120 90 16 After a little difficulty mounting the tires and getting the beads to seat on the rear tire was off on new rubber First thing noticed right away after scrubbi
57. traffic I ve used all of the above at different times and under different conditions Your mileage may vary trained rider on closed course don t try this at home etc Dragging a knee VFR Pilot Mon Sep 17 22 09 55 2001 There s almost no way to safely drag a knee on the street much less so on a Ninja 250 e If you re leaned over enough to get your knee down you ve generally left no traction reserve available with which to change your line or brake when something unexpected pops up And it will Which brings up the second form of traction the kind used on broken bones e Unless you are hanging completely off of the bike a street stock Ninja 250 will generally drag hard parts such as the centerstand before you get far enough over to reach the ground with your knee If you drag those parts hard enough they will neatly lever the rear tire off of the ground introducing you to the term lowside e The guys who race 250 s do get knees down on the track but their bikes have been modified with stiffer suspensions better tires removed center stands etc If you re curious there are racers here and on the other Ninja board who can answer your questions in detail 27 Best answer Ya wanna learn racing techniques get a bike that s set up for the same and get yourself to a good track school Once you ve been fast on a track you ll never want to go back to the street there simply isn t any comparison in terms of either fun or safety L
58. try to cheat injury with every ride I ll be taking in the pretty scenery on all of the country roads near my house and joyfully be obeying the speed limit Size matters Jenner Mon September 17 00 52 16 2001 It was unusually calm and quiet at Windy Ridge as shut down the Bandit had just arrived and was glad for the break It had been a while since had ridden the twisties mean really ridden them have been spending a lot of time riding the commute or doing short sport tours places where the 104 Bandit 1200 really shines You really can t knock that big motor and when you really need to pass that big rig on l 5 two up with all the bags full the 100 horsepower does come in handy But hadn t ridden the twisties in a while and frankly was rusty stiff and needed the practice As pulled into Windy Ridge located at the end of Forest Road 99 off of Forest Road 25 in the Gifford Pinocot National Forest realized wanted a smaller bike There said it wanted a smaller bike As sat there looking over the devastation from Mt St Helens my riding partner remarked Man the horsepower it took to level that Those words sank in as thought of my ride up to the Ridge had needed to fine tune my twisty road skills and I d brought the wrong bike should have been on another bike in my garage a Ninja 250 Oh it s not that can t handle the horsepower of the Bandit and it s not that didn t enjoy keeping up
59. ultra stable when upright and very smooth although the acceleration under any throttle setting other than fully twisted on would have seen any ninja fly past it it felt quite gutless First impressions of cornering were that it didn t dip easily into corners at all like the Ninja it took a lot of physical effort to drag it into a turn which wasn t nice at all But the most disturbing thing was when moderately leaned into one corner without any warning the bike gave a kick and tried to spit me off tried a few more corners with similar results and just couldn t get the pig to give me any feedback on what was going on with the tyres Every Ninja I have ridden and I ve ridden a few now is brilliant at letting me know what my state of traction is the ZZR gives none of this vital feedback until it is almost too late The verdict when buying a more expensive machine with an identical motor to the 250R you would at least expect some kind of handling improvement or engine performance The ZZR has neither of these things so don t bother being upset that they don t import them into the U S 11 Is ita good investment will it retain its value ohn Harmon Wed Oct 27 23 59 39 1999 opted for a brand new Ninja 250 back in 1991 to use as a starter bike Guess what ended up keeping that bike and liked it so much that just bought a 2000 model to replace it In my opinion you can t beat it Additionally they have a very good resa
60. we get into corners We overbalance the bike and steer it out from under us at the same time only steering into the corner once the lean angle has been established The trick is to do this quickly precisely consistently and above all smoothly And the way we gain that ability is to practise it over and over and over again until It happens without thinking But start out by practicing and thinking about what you re doing at the same time preferably in an empty parking lot Set up a slow wide turn and practice tightening it by steering slightly to the outside to drop more of your weight on the inside of the corner you will find that you can then steer further to the inside and turn more tightly And you d better know how to tighten up a corner before you get into a decreasing radius curve on a two lane highway at a high rate of knots You would have a limited future as a hood ornament Things like weighting the footpegs and hanging off the bike to maintain a better contact patch are techniques that must wait until you can get into and out of corners consistently safely and again smoothly every time 25 Scraping Pegs Duke Tue Apr 25 13 43 15 2000 On our last trip to Deal s Gap touched down both pegs once each without the feelers the feelers are missing from my pegs You really have to have faith in the bike that it will stay under you but It will as long as you have the correct tire pressure and are on dry clean pavement
61. wearing my whole outfit I m ready for either a sunny day or a rainstorm They re quite versatile Draggin jeans have both the Draggin J eans and Shirt The shirt is 100 percent knit Kevlar and the jeans have the Same Kevlar in the seat and knees Kevlar is one of the best materials for abrasion resistance Since most accidents occur at about 30 mph Hurt Report they should provide adequate protection from abrasion They are well made and ideal for hot weather riding got mine from Competition Accessories and they take returns if you don t like them Gloves Street gloves Catchy Mon Jan 21 23 36 42 2002 had a pair of SP3 Alpine Stars for street work Sure they were cheap at 99 but that was no excuse worst made gloves have ever owned They fell apart after three months had no feel were really loose once they wore in and slippery on the controls They split in my last crash at about 55 km h The gauntlet on the left glove was useless wore through on impact The Kevlar part of the palm was 17 torn off and the thin leather underside was knackered after a relatively short period of tarmac time At 60 MPH hate to think what the result would have been As it was my wrist was badly knocked about had all manner of minor abrasions on my finger tips where the leather just gave up was shocked it was like wearing fabric mittens rather than leather recommend getting some Spidi Carbotech gloves inexpensive at about 179 AUD
62. won t and see white smoke coming from the exhaust Leon Wed Apr 26 06 16 39 2000 The white smoke indicates that water is getting in the engine which means water could be in your fuel tank The reserve fuel comes from the same tank as the main but the reserve comes from a lower level The main setting takes fuel from about 2 inches above the bottom of the tank reserve takes fuel from the very bottom Water is heavier than gasoline If you have 1 2 inch of water in the bottom of your fuel tank it will never get into the carbs if you never use reserve When you switch to the reserve setting the water will immediately flow into the carbs try not to add fuel to the tank until after it gets to reserve This way the water is removed from the tank regularly The down side to this method is that it ends up in the carbs Another method is to drain the fuel tank regularly This would be a better method because it will remove all the water and sludge so that when reserve is used only gasoline gets to the carbs This method requires more work do it once when get the bike all of them need this don t buy new bikes The water problem occurs more often in bikes that sit in the rain My bike starts initially but the carbs flood very soon thereafter Leon Thu Apr 27 10 12 45 2000 Gas pouring out the overflow could mean that you ve got a particle of something under one of the float needles It won t flood when not cranking because the va
63. worse later 109 More classroom more tracktime The fourth session rocked was seriously nailing turn two and regularly passing all the bigger bikes safely both on the inside and outside also had turn seven wired and could pick nearly any rider off at will except for the pesky guy on the RS125 who was passing everyone and simply hauling ass should sincerely mention before get carried away in my self examination that during this whole thing was being both trailed and following the instructors mostly John Rabasa but also the other guys and they were giving me killer feedback primarily through hand signals There is nothing that know of on a bike like following a great rider on a much bigger bike through a series of turns keeping him well in your sights and having them look back and give you a big thumbs up for a job well done really appreciated the encouragement Geez OK So last classroom last track session I m sorta beat by now The fourth session ended with me running out of gas in 11 under waving yellow class bike crash and luckily not bogging the bike under lean and able to switch to reserve on the fly No yellows after the checkers and the rest of the classes two running at this point are still running hard so did too Aced seven again LOVE that corner Finished the day with a right leg cramp for a full half lap That really hurt bad Must Get In Shape Overall Pros Cons e Great crew e CSS me
64. you can see if it s a blind curve If you stare at the guardrail curb or divider lines because you are worried about hitting or crossing them strange and bad things happens a your subconscious mind seems to fight you and go towards what you are looking at but trying to avoid b you scare yourself and c you won t see what s coming up ahead e g debris in the road curve tightening oncoming car etc Countersteering VFR Pilot Fri Jan 21 00 53 09 2000 A motorcycle is turned by leaning it in one direction or the other and then maintaining the lean by steering the front wheel into the curve until the forces of gravity and inertia balance out Exactly how far you lean and how far you turn the front wheel are determined by both the radius of the corner and how fast you re moving Anybody who can ride a bicycle can do the above without even thinking about it The hard part is using words to describe something that most of us do instinctively Which brings us to countersteering which is how we all get into corners but is a technique that almost nobody ever actually practices To see countersteering at work simply proceed down a straight and traffic free stretch of road and shift your weight a bit to the right then steer ever so gently to the LEFT Yikes The bike suddenly tried to turn right didn t it In fact if you neglected the part about steering left ever so gently you probably scared the s out of yourself So now you know how
65. 10 55 2000 You will need to rejet if you make any changes to your exhaust or intake If you add a new pipe and or filters your carbs will run lean so you ll need to richen things up A carb kit will do this by giving you larger main jets and adjustable jet needles The jet needles also have a slightly different taper than stock which will smooth out throttle response through the whole RPM range and add quite a bit of power in the 3 000 6 000 RPM range If you don t rejet and run your bike lean it will a not run without the choke being partially on and b may burn melt your exhaust valves if you run it hard lean If you are going to spend the 400 to add the pipe and intakes go ahead and spend the other 90 for the jets and do it right How do improve my jetting Duke Tue Jan 11 15 39 41 2000 Carburettor jetting is the fine art of adjusting the jets inside your carburettors to provide optimal fuel flow into your engine A couple different companies sell jet kits that include 2 adjustable jet needles and 4 sets of 2 different sized main jets to allow you to accomplish this goal If you modify your exhaust or intake you will need to also adjust your mixtures in your carbs due to the increased airflow which will cause a lean mixture Depending on what mods you make you ll use Stage 1 or Stage 3 Both are included in the kit the Stage business is just marketing hype The carb kit may also improve your stock performan
66. 23 22 2003 The Kenda K657 Challenger and K671 Cruiser tires are both decent quality tires with solid grip good water dispersion and neutral profile They are inexpensive a little over 100 a pair and come in 100 90 and 130 90 sizes for front and rear respectively These tires are heavy 6 ply units that are best used for touring in my opinion They don t match the quality of Metzeler touring tires but are cost effective with good tread wear and can handle heavy loads Pirelli MT75 Jeb Fri Sept 5 10 49 59 2003 If you re looking for an inexpensive sporty replacement for the stock tires this is it IMHO The Pirelli MT75 s are cheap about 100 pair offer good treadwear about the same as stock excellent grip not quite as good as GT501 s but still very good and light weight less unsprung weight means better suspension response 85 These tires fit the EX250 rims absolutely spot on 100 80 and 120 80 are what the wheels were designed for and steering response is awesome with them High speed straight line stability will not be quite as good as with a larger 100 90 amp 130 90 setup but turn in rate and agility will be better Pirelli Strada MT68 69 lan Wed May 14 09 39 20 2003 Last summer had surpassed 12k miles on the stock Dunlop K630 s and had completely killed the rear treadwise but the front could have kept going if could have stomached it Unfortunately working in McD s for 4 years as a manager back in
67. 48 54 2000 130 80 16 means that the tire is 130mm wide and is 80 as tall as it is wide aspect ratio and fits a 16 rim A 130 90 16 is the same width but is slightly taller and has a slightly larger diameter Many folks have switched to the 130 90 16 rear and 100 90 16 front due to better tire selection in those sizes No one has reported problems using the larger tires It s unadvisable to change only one of your tires as it s always recommended they be changed in pairs however I ve seen a couple folks who have mixed tires w little problem The largest rear tire I ve seen is Leon s 140 90 16 However it rubbed against his swingarm at speed the tire grows slightly when spinning and wore a section off the tire believe he had to do a little bending of the webbing on his swingarm to make it work To be honest when riding around with him it doesnt really look any different than the stock tire if looks are what you re after The racers like Paul 311 are actually using a 120 80 16 rear tire as it said to perform better than the 130 size 86 To be honest the K630 tires stock OEM are fine for all but the most aggressive riders and the racers lve ridden mine fairly hard with no problems at all The only place they ve wandered was riding Deal s Gap in the rain but that s to be expected Do taller wider tires work better than the stock sizes Jeb Wed May 2 23 03 47 2001 The stock tire sizes are pretty good It s g
68. 5 2000 Some things to check first Obvious is to look for a nail or screw that is still in the tire Second when you fill the tire with air put a little spit over the valve and see if a bubble forms it could just be a leaking valve You can also take an empty squirt bottle put a couple drops of dish washing detergent in with some water then spray the area around were the bead of the tire is while the tire is full it could just be a bad mounting job If it is the valve try tightening it if that won t work the dealer should have no problem replacing it If it is a leak around the rim again take it to the dealer and have them remount the existing tire or mount a new one If it is a screw or nail then it is better to just replace it then try and patch it the newer types of tires are very difficult to patch both properly and fully Either way if you can figure out what the leak is before going to the dealer it will save you some aggravation My brakes are not operating normally There is a pulsing when apply my brakes Terry Mon Jan 22 16 01 07 2001 J ack up the front wheel Spin the wheel and look for rubbing Apply the front brake ever so slightly to see where it touches first Mark that part of the wheel There are 6 allen head bolts holding the front rotor to the wheel Tighten the two or three bolts closest to the spot on the wheel where the rubbing occurred If that doesn t fix it replace the pads Still no luck have a machine
69. 6 oss crac te alae Seca aaddadennae a E A 89 How do these improve handling sercon ea ate a a aA 89 What models wall fitthe EX250 sch dtcetactaces mn a bon dl awe em aewcmuieniet 89 How dol putthenvon the Dike Actes tosicocsecsunsavs co ctecchancwonpeetridedansurs a SA 89 lwant 10 change My CO atiiG icici ict ieseni er iea e aiaia 90 How do Lehange my Searine lereier a a a ae adenine 90 Does installing a new front sprocket make a significant difference eeneeesessese 90 Is there any advantage to installing a smaller front sprocket ccccccceceeeeeeeeeeeees 91 Whatdrive ratios are atainabie oireeni E T nae seiguwines 91 ljust want TORS DOWO raian n a a a a eee eety 91 ONC TUG e T EE E E N E NE E E EE E E E AE E E A E ees 92 RETO TTE EEEIEE E TNT E EE E S A Tene NT A EE A E E EA 92 I want to adjust the ride height of my DIKe 0 0 0 cccccccceccssseseeeeeeeeceaeeeeeeeeeeeeesaaeeeees 92 How dow chance the Mde Neis NG cesonia ana a a aa 92 Adjustment Tech Racine Kilisesi a 92 Chanoine TOrk POSO ensi nud seuqutindeseaduasaediaetaeoctentt osu eieaantente 92 Are there any disadvantages to lowering the Dike 0 0 0 eeeeesseseeeeeeeeeeeeeeeeeeaeeees 92 Why is important to raise lower each end of the bike together ccccsseeeeeeees 93 I d like to improve my bike fOr tOULING sesiiiiion i a E 93 Pd like to ser SOME Newari PS sor aisenice it he T a esate NAN 94 PavliketOrCet SOme NOW PCoS icteric chaser sadam r
70. 8 58 5 Total 23 47 hrs 1552 mi 31 27 49 6 66 1 On The Track First day at Sears Point lim Race Tue Nov 16 16 52 08 1999 The day started off incredibly early for me 7 a m I m really not a morning person and combined with the seemingly bitter cold and fog and my personal haze was sort of in a funk got a largish boost however when discovered Keith Code himself was going to teach our group all day I m not sure if this is how it s normally run but tt was something to look forward to After the first classroom test we went out on a fourth gear no brakes drill This was at about 8 25 and it was still pretty cold and was unsure of the stock suspension and tires but was willing to give it my best shot The plan was to take two sighting laps and pre gridded first in front of the rest of my group who all had at least 500 cc s on me However think my best break was seeing the instructor pull out in front of me with Rabasa on the back of his leathers Those here and elsewhere will know John as a great 250 production rider and now know him as an excellent instructor After the sighting laps they sent us on our way It was very odd not having anyone in front of me on my first track lap at speed on a track I d only ever seen from the sidelines but was determined to make the most of it did fine for most of the lap even feeling comfortably fast in the carousel but nearly completely blew turn 7 missing my turn in
71. A 42 How do Dadi Ust chain tension voc careenceeuanindeath a a aa 42 How doi Teplace Mme seMain cecs e a a a Coasdielmeinincuanacs 42 What replacement chain sprockets should I consider cccccccccesssseeeeeeeeeeeaeeeees 43 HOw do adyust ne Val VCS 2 vixcccas asec eget olen cekeeeis Recaduehaciadton ciate edd aadsuaed Bese eomantaess 43 Why do the valves need to be adjusted ee cccccsssesesessseseecececeeeeeeeeaeaeeeeeeeeeees 43 What 1s he adjUStiment Procedure se a sai eoaaac lace ees 44 3 Is there a special tool to make this easier ce eeccccccccecceseeeseecececeaeeeeeseeeeeeeeeaenees 45 What are the acceptable clearance ranges ccnsiieu cad n eared naacd ea 45 Are there any advantages to selecting a specific setting within that range 45 What happens if the clearances are too tight lOOS eecccccccececeeeeeeeeeeeeeeeaaeeeees 46 Do I really need to adjust the valves every 6000 miles ccccccssseeeeeceeeeeeeeees 46 What is the hot soak valve cleaning Method csesessesesseeeeeeeeeeeeceeeeeeeeaeaas 47 How do Pchanee the Spark Plies ic siscacentsansannamaccuntnveddadduntedevaonstsnianacderecaniadedacceas 47 How dol service ne Drakes cscs iat atest E 48 Howdo T bleed the Drake INES sucses asus damccendetss 48 How dol change the brake fluid wic ieniniiniiielen ule 48 How dob replace the Drake pads Fisc cccecssccatesensa cence cesusenmenc TE 49 What replacement pads
72. Installation Drop the lower portion of the inner shock assembly small 1 5 aluminum tube into the shock with the flat part facing down Place the silver tube back into the fork Slide the bushing down the silver tube and align the notch facing toward the right or left side It is important not to face the notch to the front or rear as this will cause premature wear to the fork tubes upon sudden stopping or acceleration Drive the bushing into the fork using the PVC pipe Apply oil to the new seal and slide it down the silver tube with the spring facing up Slide the old seal down on top of the new seal and use it as a cushion to protect the new seal when you use the PVC pipe to press the new seal into the shock Slide the old seal off and install the retaining clip and the dust cover Slide the inner fork tube components back into the tube Spring and larger rod golf tee thingy Screw the allen bolt back into the bottom of the tube Apply some silicon sealant to the copper washer to help seal it Tighten the allen bolt to the proper torque Again you may need to hold the inner fork tube using a wooden dowel or the proper tool from Kawi Once you have tightened up the bolt slide the silver tube up and down It should bottom out when pressing it all the way in and it should hit the spring when pulling it out If it doesn t something is assembled wrong If everything slides smoothly reinstall the forks fill them with the appropriate amount of
73. OM NG UAC Kea sees sscaystitnte i E can icant aus bacasitecataen seas cect stam taea Meattecae enna bocnagaceattad 108 PEA ale seats COUN r ee ataeneph seuss adattne et ese ee ee nactunaniaceteaseatueanie ss eateamteeee 108 DSO SHO Al SC Ab C1 OO i taste ucenscanartioms Sancta eon aanuiuanaaea seaamranaencacoaamaaeersaateas 110 Cis TING SUR CE E E E E ES E E E anaconda cuca duct E ET PE AS T 111 Real Worn Peri Orman E asia a a a 111 RODEIA Tra FC tices sie T NS 111 Miad enurese aes Sacawaansasagatastenaneacasb oes saad eeainenae ecaienaeane martes 112 DDS I METIS CS rt sth ace catiects Cates ce lucia contains ean crate onthe ic eetancteabet cn aantsaetatons 112 Necessity Ol proper CC AN cri shss ch e a setae ek aad 112 Riding A2eain Alteran Aceder neete te ueteauadiniorse Mosanaiscnde tents 112 Whats the Deals Gap trip all ADOUG scrie E assets eile nce atielae tein ea 113 About the ZX 2R Model What is the ZX 2R Jeb Sun Sept 15 13 16 39 2002 The picture on the home page is not of my bike exactly but it s rather a concept image of what my bike is in the process of becoming When got my Ninja several few years ago it was mostly stock then sat down and drew up a design in Photoshop for what wanted the bike to look like My real bike looks practically identical to the image on the FAQ home page minus the seat cowl not yet complete but the prototype is coming along nicely and the lower fairing painted flat black right now
74. The Kawasaki Ninja 250 FAQ Brought to you by the folks at www ninja250 info Table of Contents OOUE TG Ze ZI Mode krian sacle seed ey som a satecnacenassesaa nian laauities ate auegtiarseanene 8 WY als DE ZAAR cist resbenncta cna ganudtinanctiataticuar G 8 Cam Teet ZA 2R decals enni Ean E E teantaeteses 8 Is a seat cowl available for the Ninja 250 einai ea aea a aaa aa aai 9 TN Wi IC So atasaaeti atin etrcsecata aurea daaeeeataiaer deed eanetat ci iaetaa eM ntact a saakuas pacbeniet ta ampysechieicaatante 10 I want to know more about the Ninja 250 motorcycle cc ccc eesseesssesseecececeeeeeeeeaeeaeeseeeseeees 10 NY at AS ANDITO as itecicce acacia nari ak Sen AA 10 What kind of performance can I expect Out of it 0 ceccccccccceeaseseeeeeeeeeeseaeeseeseeeeeeeaas 10 Ani 1100 big Tr This Motorcyle sisi sdiwacaecnnedesienns E eer iad 10 AmI osma for Mis motorcycle nnsa eee ste a i aviainedeeend 11 How does the EX500 compare to the EX250 0 en n EN 1 What about the ZZR250 how does it compare 0 0 eee eceeesccecessseceeesseeeceeseeeecessseeeeeenes 11 Isita good investment Will it retain its Vale mosses oinera oen ai aai 12 How lone will a Ninja 250 engine last sc scs ss3esetersestesssdscetesmenserdarrseeiataaienaeeteesaate 12 Shouldn t I consider a bigger bike Won t I want one later anyway ccccsssseeeeeeeees 12 Can leet Some stats Specs for the DiKe Yc rsictecr ates sanektectsatiet aa 12 Specifications a
75. Why does my bike take so long to reach normal running temperature cccc0008 37 How far can I go after putting the fuel petcock on reserve ce eececcccccececeeeeeeeeeeeeeeaes 37 Wat kindsor fuel Should Tuse kirasa a E crtteweaeiseed ST What are those tubes hanging down from the bike fOr 0 0 0 eceecececececeeeeeeeeeeeeeeeeeeees 38 Should I use the side prop or centerstand when I park ccccccecccccesssseeeeeeeeeeeeeeeeseeeees 38 Why does my gas tank sometimes whine when I StOp cccccssesescecececeeeeeeeeeeeeseaneeees 38 INFATLEM AIC CIRC Ali sansisasenn a ates cattle iawtunsualbcias iawtinet rend ine wnat aneeal iameutina es 39 peed advice for maintaining my DIK iisiecsescashshuwesesbiadeon a a a E eia 39 Howdo TC hain Ge He oU r masines n a EE 39 What is the oil Change procedure sioiias aaa a eee 39 How often should I change the oil What kind should I use ce eececcceeeeeeeeeeees 39 Are there preferred brands of oil for motorcycle use ccccccccccsesseseeeeceeeeceeaeeeeeeeeees 40 Issynthetic Oil Teally alll hat reat nnen a 40 W hat ol niere are availabe Forio E 40 How Go Service tne Tal OVC hesione a a E ON 4 How do clean he Gri VeC Hai eener siwon ulwu ten oeenwiukaedeaeacet A 4 How often should I lube the chain what should I use to do s0 ooo eee eee eee eee 41 W hat arc some pood Chaim UDES orainen deeb itiaal a a a aa r 41 How do I measuite chain slack iienaa
76. a handful and you have a handful like to brake really really late so for me the HH s were a good fit YMMV 49 I ve never used a Ferodo on my EX but had a set on my RZ350 and was quite pleased with them If the HH acquisition situation heads the way of the Dunlop K591 rare species I d say go with the Galfers At the very least it seems that there is always a Galfer dealer at every race like working with dealers that provide that kind of support What other components should check Lou Wed Mar 22 23 14 31 2000 When changing the brake fluid the book says you should also replace the master cylinder and caliper dust covers seals If you replace these items before they crack and let moisture in it can save you big trouble later caused by water corroding the callipers and pistons If you put a light coat of grease compatible with the seals between the seals and the dust covers it will prevent water from getting in during rainy day rides or washes unless you use a high pressure sprayer in which case never mind This is something that can be done the first time you replace the pads while you are inspecting the dust covers for damage How do service the carbs filters What carb components do need to check Paul 311 Sun Jan 23 22 33 21 2000 The carbs on the Ninja are really simple things and should never need to be completely replaced There are a few components which may wear out though The float valves are these
77. about jet kits is they come with instructions and they are based on a lot of actual dyno research so they get you in the ball park right away That s what you re really paying for did some ass dyno jetting on my Ninja last year later duplicated the dyno testing same jets ona real dyno The old ass dyno picked the same jets the real dyno picked One thing to watch out for if you buy jets on your own Dynojet brand jets have their own sizing system that doesn t correspond to Keihin jet sizes What components are needed to rejet without a jet kit Leon Mon Jun 23 19 54 45 2003 e wouldn t advise spending the money on a jet kit If you change the main jet size you can buy the jets from Kawasaki for about 5 each 81 e If you adjust the needle settings you can do it with 4 flat washers 4mm washers for the metric world for a dime per washer e You can drill the slide holes with the biggest bit that will fit down from the top I think that s how Dynojet decided what size bit to include in their kit e And you can remove the plugs from the idle mixture screws with another small drill bit and a wood screw e just put two or three washers under the needles for pods and another one or two for an exhaust pipe and you re 90 of the way there It s that last 10 that can be difficult How do adjust the idle mixture Jeb Thu Apr 18 23 43 33 2002 Pull the carbs drill a small hole in each of the mixture screw caps careful
78. ack of a truck A really serious chain run through the bike s frame and then locked around an immovable object is your best bet for overnight security if you can t park out of sight in a locked garage Alarms can help too Gorilla makes a good one if the bike s parked where somebody can hear it go off Bear in mind that nothing can prevent a professional thief from swiping your bike if he really wants to go to the trouble so think in terms of making it as hard on him as you can and keep your fingers crossed The good news is that bike thieves prefer Hardly Ablesons if they can get em Ninja 250s are way down on the list of most stolen bikes Gorilla alarm Jeb Tue Feb 22 09 25 56 2000 have one of these and it works pretty well It takes less than 15 minutes to install and requires no mounting equipment just hook it up to the battery and nestle it behind the coolant reservoir It has shock tilt and current sensing and costs about 80 It doesn t have a microwave sensor but this is usually only found on 200 models No it wont keep people from loading your bike into the back of a truck but it would deter most common people from messing with your bike for example one night came out of a bar to find two guys taking pictures of their drunk girlfriends sitting on my bike was cool about it and joked that it was 5 a seating but was really pissed off Anyway if I d had the alarm then doubt they would have done so Luggage
79. ad as the rider is usually catapulted off the bike at a higher speed than he or she 34 was travelling sometimes in a high arc resulting in tumbling bouncing flopping This is where the worst injuries occur and why we wear good quality CE approved armor in our protective clothing you wear protective clothing right How do we avoid highsides and lowsides By making smooth gentle control and steering inputs maintaining headbearings and suspensions having good quality serviceable tires and not riding overpowered bikes like RT s want to get a bike but my parents won t let me Jeb Fri Jun 1 9 36 23 2001 This is a question that comes up from time to time but in fact a relatively small percentage of those who ride the 250R are under 18 years of age and therefore require parental consent My answer would not be to just buy one in any case If you are not 18 you cannot insure or register a vehicle without a parental signature anyway in most states The best route in my opinion is to ask if you can enrol in an MSF course most parents will say yes After this parents are more likely to accept the purchase of such a vehicle since they know you are properly trained and responsible enough to take the class to begin with If the answer is still no see what they think about a moped bicycle with a very small motor not very dangerous or a scooter you can then trade up in a few years If all else fails you can do wha
80. amp bolts are torqued to 14 5 ft Ibs lower bolts to 22 ft Ibs If you want the front even lower you can take off the bars and then loosen the 4 clamp bolts and slide the front end down put a car jack under the front of the engine so the bike doesn t slide all the way down to the fender don t go over 1 Then make some spacers to be placed between the triple clamp and the handlebars went to a machine shop and bought a small 1 2 thick piece of aluminum and then cut and shaped it to fit under the bars about 2 x 3 also cutting a hole in the center the same size as the tubes and holes for the bar bolts Go slow measure and mark everything ground all of the edges smooth and painted it black it looks factory original Another benefit is it raises the bars up a bit so there Is less back arm and wrist strain It s a lot of work but it really made a comfort difference for me Are there any disadvantages to lowering the bike Wolcott Mon Nov 1 11 14 32 1999 e You have to shorten the side stand so the bike won t fall over to the right side e Also it s more difficult to use the center stand roll the rear wheel up on a 2 x 4 and then put it on the center stand may find that should remove the centerstand if it turns out to hit when leaned over 92 e t does slow your steering down slightly if you lower only the rear which effectively pushes out the front forks The bike is so light however that you re not likely to no
81. and slightly up they should mirror each other like this When this is done this correctly a 1T mark will be visible on the flywheel through the view hole you ll need a flashlight to see it and the tappets below the cams will wiggle when you try i T to move them under your finger Here is a photo of the engine at TDC for cylinder 1 Now take out your feeler gauges and slide the proper gauge finger under the first cam of four for that cylinder between the cam lobe and the top of the valve tappet it should slide in with little effort and drag slightly when the clearance it correct If the clearance is not correct grab a 9mm socket and loosen the tappet locknut there s a small screw on top of the nut Use a very small flathead screwdriver to turn the screw out a bit until the clearance is correct if you use the looser end of the acceptable adjustment range it will take longer before the valves need adjustment again Rotate the engine again until the right cylinder cam lobes are in the proper position a 2T mark will be viewable on the flywheel and repeat the check adjustment process If the exhaust valves need to be adjusted you may need to remove the radiator retaining four 10 mm bolts to move it out of the way the coolant hoses will keep the radiator loosely attached to the bike the exhaust valves tend i sock c to take longer to work on 7 i hi aw F es Wipe the valve cover gask
82. annot ride a bicycle there isn t enough time to learn this during the course e Anyone who has health or physical fitness problems such that riding a bicycle for more than a couple of miles would be dangerous Riding all day is strenuous e The guy who has been riding for 20 years and is taking the course with his wife so she can learn to ride Please don t you ll make her nervous she can t listen to both you and the instructor e The guy who has been riding for two years or more and just heard about the course Take the experienced rider course instead ls the course hard will be able to pass Leon Wed Aug 8 15 37 09 2001 I ve sent a few people home here s why Biggest reason is not showing up on time If you re late for the course cannot let you stay If you have an accident after being late and missing part of the course the program office says they ll hold me responsible for your injuries That won t happen Riding a bike is an important skill I ve only had one person pass the course that had never ridden a bicycle She had done a lot of practice on a little dirt bike at home and had taught herself to ride that Finally you have to progress When you fall so far behind the rest of the class that you endanger them cannot allow you to stay The circle riding that happens on the first day is relatively difficult if after a couple of hours you cant reliably make the bike go in the direction you want it to go have to p
83. around 160 pair Metzeler Daryl Mon Jan 3 15 55 24 2000 I ve gone through two rear and one front Metzeler tires and like them very well I m ordering a set here in a few weeks Front is a Lazer 100 90 16 Rear ME 55 130 90 16 get 20 000 miles from the front and 10 000 miles from the rear Best rain tires I ve ever used with good ride and very good feedback and grip It raises the bike a little with no tire clearance problems Michelin Jeb Sun Mar 6 01 35 27 2000 Michelin no longer makes tires that will fit the EX250 rims How do determine tire size Duke Sat Apr 22 09 48 54 2000 130 80 16 means that the tire is 130mm wide and is 80 as tall as it is wide aspect ratio and fits a 16 rim a A 130 90 16 is the same width but is slightly taller and has a slightly larger diameter Many folks have switched to the 130 90 16 rear and 100 90 16 front due to better tire selection in those sizes No one has reported problems using the larger tires It s unadvisable to change only one of your tires as it s always recommended they be changed in pairs however lve seen a couple folks who have mixed tires w little problem The largest rear tire I ve seen is Leon s 140 90 16 However it rubbed against his swingarm at speed the tire grows slightly when Spinning and wore a section off the tire believe he had to do a little bending of the webbing on his swingarm to make it work To be honest when riding around wi
84. as you catch your breath and look through your cracked windscreen for the next racer to pass You get a good drive out of the corner and shift up through the gears on the straight as you slowly reel in the next racer in front of you You inch up alongside and he glances over The turn at the end of the 110 straight is a 90 MPH left hand sweeper Both bikes are revving at 14 000 RPM in 6th gear the speedometer would read 115 if it wasn t taped up and he isn t going to let you outbrake him and you sure as hell won t let him outbrake you At the same instant you both downshift and heel the bikes over He takes the outside line and you are two feet behind him Will he apex wide enough to let you it drags through the corner and you dive into the apex right under his bike He backs off at the last minute and lets you by but he s right on your ass and that was only the second lap of six Scared Yes Exhilarated scared and so high on adrenaline that the only thought in your mind is how you are going to pass that next rider and you see the line on the race track with a clarity reserved for crystal meth trips How scared do you need to be If riding like that doesn t scare you you are probably too foolish to be riding something capable of more speed Of course there are more suitable and practical streetbikes Bikes with more comfort range capacity and power all have their uses But the 250 is just as capable of scaring a rider as an R1 O
85. ass had some time on both the 125 s and 250 s found it to be a lot quicker and better responding then both of them think it also outperformed the 400 in both acceleration and handling It s a really light bike and handles like a dream It will out accelerate all but the most expensive sports cars But it s also a great beginner bike because the power doesn t come until 8k RPM so it won t intimidate a beginner Power is aplenty from 9k all the way up to the 14k red line peak hp is at 13k if you manipulate the 6 spd properly you will rarely lack for acceleration If you were going to get a 250 the Ninja would be it except for an Aprilla RS250 or something expensive Am I too big for this motorcycle Duke Sat Apr 29 05 12 18 2000 I m not a tall dude but Leon is about 6 2 and he s got over 100 000 miles on one of his 250 s Most of the other guys I ve met on 250 s J eb Andrew Daryl are all around 5 10 6 but they re all skinny think weight is actually the more important factor anyone over 250lbs or so might want to consider the ex500 The ex250 is small but so are most sport bikes That s the whole idea that they re fast and lightweight and small If posing is what s important buy an R6 If having fun s important buy a 250 They re a blast Someone here made a good suggestion the other day Since the dealer won t let you do any sort of test ride to see how you ll fit for a long ride Sit on the bike at the dealer
86. be fixed and what can be overlooked remember that things like aftermarket levers and signals cost much less than factory parts Don t forget to make the insurance pay for the damage estimate also E mail if you have any questions need recommendations for tools parts What should a good set of tools include Wes Sat Mar 22 11 53 49 2003 Here s what you need to work on the bike Metric Socket Set Sears Craftsman or equiv got mine for 10 on sale at Sears e 10 Ratchet with 3 8 drive e 3 8 gt 1 4 drive adaptor e 1 4 drive sockets 4mm 6mm 8mm 10mm e 3 8 drive sockets 10mm 12mm 14mm 17mm Additional Socket type Stuff e 1 2 gt 3 8 drive adaptor 1 2 drive 22mm socket front axle 1 2 drive 24mm socket rear axle Adaptor for 1 4 socket drive gt 1 4 hex head screwdriver bits 2 3 Phillips 1 4 hex head screw driver bits 3mm 4mm 6mm 8mm Allen 1 4 hex head screw driver bits Screw Drivers e Handle to fit 1 4 hex head screw driver bits If you only buy one handle make sure it is the non ratcheting type and try to get one that Is not hollow e Adaptor for above screw driver to fit 1 4 drive sockets usually comes with it if you get an assortment of bits e 1 8 Flat tip screwdriver use for steering head nut you bang it with a mallet 72 Misc e Spark plug tool elbow piece from stock toolkit e Rubber mallet e Torque wrench Must have Minimum 10 deflection bar wrench from WalMart 10
87. can lever the rear tire right off of the ground introducing the words low side and road rash into your vocabulary avoid this While the 250 won t generate modern levels of cornering force due to its narrow tires and outdated stock suspension components it will certainly get into and out of corners faster than most other 26 sportbikes and has no bad habits to speak of Altogether you couldn t pick a better bike on which to learn cornering techniques Downshifting in a turn Duke Mon Aug 7 23 04 27 2000 Last spring while riding at Deal s Gap there were several times that locked up the rear tire going into very sharp turns when downshifting a little too aggressively As someone else mentioned here it causes the rear tire to skip to the outside of the turn just as you release the clutch Nothing unmanageable but something an expert rider probably wouldn t do Since then I ve been working on bliping the throttle slightly while downshifting hard through each gear This allows the RPMs to quickly raise to match the wheel speed for each gear as you downshift and eliminates rear wheel skid It s still effectively using engine drag to slow you and also maintains the proper gear to exit the corner The way you do this is While downshifting through the gears hit the throttle hard and then let off very quick just at the instant you release the clutch You ll want to give it enough throttle to raise the roms by about 1 500 If you do thi
88. can t get it started eee cece eeeeeeeees 68 My battery is dead how do I push start my bike ee ccccccccceeseseeeeeeeeeeeaaeeeees 68 My battery is dead how can I bring it back to life 0 ccceeseeeeeeeeeeeaaeeeeees 69 Myeneine 18 TUNIS POOPY coves cevisdienina tinea a itn detaalannebdenttaw use N 69 My engine lacks power under throttle load eee ccccccssseeeeeecececeseeeeeeececeeeseaaeeeees 69 My En eine 1S BACK TIMING eenaa a tsasancascGe a tecbiaad naacanedsnande 69 My bike will run for a while but keeps losing power and dying when I ride it 70 I thamiksiny ike 4S LOSI ali odie ns o a a a i 70 My brakes are not Operatin normall y esis ess uin A R iene veanats 70 There is a pulsing when I apply my brake c cece cccccceccssesseeeeeeeeeeaeeeececeeeeeaeeneees 70 My Drake Pads are OPM esera A 70 My handlebars shudder when T 11d cciasscecedueiek de beaiitesedceese a 70 What should I check for this problem cccceccecccccccesesseeececeeeeaaeseeeeceeeeseeaesseeees 70 What if steering head bearings are bad icniswiniiisue eects a eee 71 My clutch lever rattles when I rev the engine ccccccssessssececececeeeeeeeeeeceeeeeaaeeees 71 Can I ride my bike home if the clutch cable breaks cc cccccessseeeeeeeeeeeenens 71 need to fix some accident Catia CC ariero a e EE A 71 I need to realign my forks and front wheel ccccccccccecceseseseeeeeeeeeeeeseeeeeeeeeaaas 71
89. ce by smoothing the low and mid range response With a Muzzy exhaust system the Dynojet kit in my bike makes a very noticeable difference Instructions for installation and adjustment are included in the jet kit plus they have a 1 800 number for help If you have a little mechanical aptitude you can install it in a Saturday afternoon However plan on taking the time to make a few adjustments to get it just right For 90 it s worth a try and you ll have everything you need carb wise to add a hi flow pipe or intakes in the future 80 How do l install a jet kit Jeb Fri Mar 31 17 05 50 2000 The instructions that come with the package are concise and assume you have some technical ability if you have a Kawi service manual it will clarify a few things There is a bit of an art to this you ll see that after putting the carbs back in after the first rejet session You may have to pull the carbs out several more times before getting the results you really like There are four main steps to this process e Drill the vacuum hole of each needle holder diaphragm with included drill e Replace the stock needles with new clip retained needles e Replace the stock jets with the recommended replacement this may not be the jet you end up keeping e Drill out the idle screw covers with included drill and close each screw then open 2 5 turns It is important to be careful with these parts they are manufactured to very specific tolera
90. cecceceeeesesesseeseeeeeeceeeeeeeeeeeaaaas 56 What kind of battery should T Use sssc c6ci01 dish evin e A vii ian 56 How dol Work On chichi components ssnin ane erecta 56 How dot ibe the Clutch Cale vase carnasurcauls costnetasusinesactrahisansariusi cunt cous a 56 How do Treplace the clutch cable sccicuntet Lassie ceeecanetboniuenectudusteeberseshereodaskiassuedeteiess 57 How do I refurbish a slipping clutch ileana 57 How should T Clean the DIKE husene maine s a a ntociasetues 57 POW C OFAN Se GV 1Ce Ne ES a E wesuasetmboteenvetansets 58 What ire pressures should Use ss tateetanncesssstsMareateniceaas seaetensaiocang aeuties n 58 What tire pressures should I use for everyday riding cccccesssseeeeeeeeeeeeeeeeees 58 What tire pressures should I use for touring high speed riding etc 0 58 How often should I replace the tires cc ceceeeececceccenseseeeececeeesseaeeseeeeeeeeaaenees 58 What do I need to know when looking for replacement tires cceccccseseeeeeeees 58 What tire makes are available that fit the 250 ccessssseseseeeececceeeeeeeeeeaeaes 58 Flow do T deternmine tire S267 orree a a wera Manieantccacenes 60 Do taller wider tires work better than the stock sizes cceeccceccceceeeeeeeeeeeeeeaaes 61 Do 120 width tires really work better on the rear ccc eeeccecccecesesseeeeeeeeeeeaes 6l How do I raise the front fender to fit a 110 width tire nnnese
91. chs removed my mirrors the e Killer technical track wrong way leaving metal bits just e Quick comfort level waiting to fall out Found error e Quick reduction of lap times removed metal bits to pit wall only e Total confidence that can be found one of two important bits later competitive e Cold in morning e Bad coffee If can ride this well on a box stock EX250 have a pretty good shot at being competitive next year remember a few things John told me at the end of the day which struck me e My stock motor is pulling faster than his 250 racebike He said that coming out of six his ZX6 was not catching up nearly as quick as he would have thought e need to learn to o Pass I m a wimp o Tuck Piece o cake 250 s can scare too Gabe846 Mon Jun 19 19 16 22 2000 If you think the 250 Is incapable of scaring you you need to take it to the racetrack How do you scare yourself on a 250 Ninja Chase another racer into a corner too hot countersteer with all your weight and feel the footpeg bracket dig into the pavement of the off cambered turn making the rear tire slide and bounce around Ease off the countersteering and then feel the bike snap back onto it s line as you give the throttle the last 1 4 inch and the motor bounces off the rev limiter as you inch past the slower rider in front of you with 6 inches between the two bikes You pull in front of him upshift without rolling off gas slam your helmet down onto the tank
92. ck on Doing a full debaffling yourself may be difficult Other options are to drill out the rivets in the endcaps little bit louder tone or to use a long rod place it down the muffler pipe and hit it with a big hammer to puncture the inner baffles to allow a more straight through flow of the exhaust bit louder than drilling rivets or you can do both I want to upgrade my suspension Front end How do I stiffen up the front suspension Paul 311 Fri Jun 2 17 23 06 2000 You can do a few things e Buy aftermarket springs and drop them in e Buy some washers and use them as additional pre load until you get the sag set correctly this won t make the springs any more stiff but will put you in the middle of suspension travel e Cut and grind your stock springs to a shorter length and add big preload spacers this requires a blowtorch and a flat grinding wheel e Send your forks to Aftershocks www aftershocks suspension com and they can do anything from changing the oil to a complete re valve On the rear shock you are limited to getting it replaced or rebuilt Having it re worked will make the valving better but you will also need a stiffer spring Aftershocks has a lot of options there too You can call them from 10am to 6pm California time at 650 494 8849 76 Where can get some preload spacers Daryl Sun May 14 17 52 24 2000 use PVC piping from the hardware store don t remember the diameter of the tubing bu
93. cuum valve in the petcock won t let fuel flow Remove the carbs tip them upside down remove the float bowl and then each of the floats and needles Look for something between the needle and it s seat Another possibility is damage to the needle tip 67 My bike has been sitting for a while and can t get it started MylittleNinjette Tue Dec 24 16 33 48 2002 This assumes the bike was running just fine before it sat and that it sat for months This also assumes that rodents haven t packed your exhaust pipes full of seeds or nesting If the bike just sat for a few weeks odds are that the carb bowls are just empty In this case if you have a prime setting at the petcock set it to prime and try again otherwise keep trying to start with the choke at wherever it usually would be and throttle partway open until it fires So that you don t overheat the starter motor use the starter in short controlled bursts of 5 seconds or so with a 10 second rest in between 1 Does the starter crank the engine If yes go to 2 If not then check the battery eg signal lights or horn works and charge if needed Keep the charger handy in case the battery wears down or hook your battery up to a car battery car off If the battery is OK but the motor won t turn over then there is either a starter problem like it isnt getting power or the motor is seized and this would take years of sitting Put the bike in gear and see if you can turn th
94. d breaker 3 GOOD tire irons 3 rim savers plastic sheaths to protect the rim lip Soapy water 1 Elevate the rear end centerstand 2 Remove the brake a Disconnect the 2 bolts that hold the unit over the rotor just leave it connected to the brake line 62 Remove the axle nut cotter pin Remove the axle nut Slide the wheel axle slightly forward lift the chain off the sprocket and place to side While supporting the wheel remove the axle Simply slide the wheel rearward to remove Lo Via a At this point if you bought the tire from the bike shop you can take it there to change they ll probably charge you 20 30 bucks to replace If you want to do it yourself Now you want to remove the tire from the rim The tire is sealed to the rim by air pressure the bead is sealed to the rim it requires tremendous pressure to break the bead recommend buying a bead breaker rather than the I ll jump on it method which can result in serious damage Through this whole process make sure never to put undue pressure on the sprocket or more importantly the rotor use a milk crate not stolen from wawa promise open side up to place the wheel on such that there s no pressure on the rotor Also you don t want tire irons directly on the rim lip this can result in damage and an inadequate seal Always place a rim saver on the rim before prying with the tron 1 Use the breaker to break the beads You ll know when t
95. d treatment time has been reached open the clamp so that the cleaner stalls the engine do not start the engine again for several hours Reconnect the carb hoses and pour the remainder of the cleaner into the fuel tank if desired When next starting the bike the engine may cough and sputter a bit as well as belch out some nasty stuff from the tail pipe this is to be expected Go for a ride and fully warm the engine up then change the oil Smoother idling and better efficiency may be noted thereafter How do change the spark plugs Jeb Sun Jan 7 13 39 58 2001 Spark plugs are recessed into the top of the engine The owner s manual suggests they can be changed w o removing the gas tank but if you ve never done this before think it s easier to remove it first 47 Remove the seat and remove the two bolts holding the back of the tank to the frame under where the front of the seat attaches Also there is a bolt on each side of the gas tank that holds it to the upper fairing these must be removed as well to get the tank off It should not be necessary to remove the fairing Pull the fuel and vacuum hoses off the petcock and slide the tank rearward and up Now you see the top of the engine Gently remove the two ignitions wires by the boots where they attach to the plugs Then take your handy spark plug wrench that came with your bike s toolkit and remove the old plugs Examine the plugs See of they are dark white bent oily
96. e Stage business is just marketing hype The carb kit may also improve your stock performance by smoothing the low and mid range response With a Muzzy exhaust system the Dynojet kit in my bike makes a very noticeable difference Instructions for installation and adjustment are included in the jet kit plus they have a 1 800 number for help If you have a little mechanical aptitude you can install it in a Saturday afternoon However plan on taking the time to make a few adjustments to get it just right For 90 it s worth a try and you ll have everything you need carb wise to add a hi flow pipe or intakes in the future What is carb sync Duke Thu Jan 13 12 53 14 2000 Carb Sync is matching the butterfly valves in the two carburettors so they both open the same amount Your bike will not run to it s optimum level if one cylinder is running harder than the other The easiest way to understand how the adjustment works is to take your carbs off and look at the linkage There s a screw adjustment in between the two carbs that adjusts one butterfly in relation to the other Carb sync is adjusted by measuring vacuum through each carburettor and setting the butterflies so vacuum matches There are fancy gadgets to do this but there s also a quick and easy way to do it at home 32 Get a piece of clear plastic tubing about 3 long Place some thick liquid in it like motor oil something that won t hurt your engine if it gets sucked
97. e feet to spare and felt the thump as my rear wheel came back down from the involuntary stoppie Never lost control but never had time to think about what was doing either Wish I had a videotape Stopping in traffic Patrik Wed Apr 26 23 20 26 2000 Remember to always check your mirrors whenever you stop for a light to make sure the guy behind you isn t sleeping this is taught in the MSF think that risk is smaller and can be battled if you blow through a yellow light than the chance of someone making a right turn and not seeing you Remember that most people making right turns have a lane of straight or left turners blocking their view as well Stopped in traffic VFR Pilot Thu Aug 2 15 24 03 2001 To avoid being squashed 1 Always leave the bike in first gear while you re stopped at an intersection 2 Watch your mirrors 3 Stay to one side or the other of the car ahead of you It gives you somewhere to go If you must make a quick exit 30 4 If you re in California lanesplit The drunk can t hit you if you re between two other cars But even then still pay attention to items 1 amp 2 and get the heck out of Dodge before any impact 5 Work on developing your situational awareness That s knowing exactly where all the traffic around you is located and constantly updating your mental map of where they will or MIGHT be in the next few upcoming seconds The only real defence a biker has in a bike vs cage col
98. e fender on You ll need a really long socket extension to get them out Remove those two bolts on the lower part of the rear fender as well as the two fender bolts just under the seat and the two bolts under the battery That allows the airbox fender to move back just enough to get the carbs out without bending any of the rubber parts too severely However believe the last time had the carbs out did it without moving the rear fender You just have to get somewhat forceful with the rubber boots If you push the rear ones into the airbox it can be done by forcing one of the front boots off and the other one slips right off Remember this procedure for re installing them How do l adjust the bowl floats Wes Sun Jul 2 08 10 30 2000 Fuel Level 0 5 1 0 mm above the bottom edge of carburettor body Float Height 17mm Drain the fuel out of the carburettors into a suitable container Remove the float bowl by taking out the screws with lockwashers Slide out the pivot pin and remove the float Bend the tang on the float arm very slightly to change the float height Increasing the 51 e float height lowers the fuel level and decreasing the float height raises the fuel level e Assemble the carburettor and recheck the fuel level e If the fuel level cannot be adjusted by this method the float or the float valve is damaged How do I clean the carb parts Duke Tue Aug 29 22 33 47 2000 Crash course in carb cleaning Take o
99. e for wearing with full racing leathers pant inside the boot and if you wear trim fitting jeans you can t always get the pant leg over the boot because of the hard shin armor l m sure other brands like AGV Spidi Dainese etc offer many of the same features as AlpineStars but they may be harder to get www newenough com currently lists quite a few used boots also check www alpinestars com for their current line up Army Boots VFR Pilot Tue Feb 29 22 30 08 2000 Despite having walked many miles in them wouldn t recommend them for biking They have no ankle cups or armor of any sort If you do decide to use Army boots make sure that you re using the all leather boots not the largely nylon Nam boots Nam boots were evolved for tropic heat and provide very little protection except to the sole of the foot As Wolcott mentioned tuck in or duct tape your laces to prevent tangles Imagine pulling up to a stop sign starting to lean to one side and then discovering that your shoelace is tangled in the peg and you can t put your foot down to support the bike Parachute Boots Barry Fri Mar 3 11 39 36 2000 Also called paratrooper boots or jump boots The original paratrooper boots were made by J oseph Corcoran Shoe Co Stroughton Mass during WWII they still make them and they are called Corcoran Jump Boots believe most military people think of them as the best around Better military surplus stores carry them or you can
100. e is any movement at all the steering head bearings are loose To tighten them loosen the top nut that is between the fork legs behind below the ignition Under that and under the top clamp is another nut with a slotted head Use the spanner wrench from the tool kit or a hammer and punch to tighten this lower nut one tooth at a time Tighten the top nut before checking the forks again usually loosen the locknut then tighten the bearings until can feel a noticeable tightening then I back off a bit tighten things back up and go for a test ride Once the forward and back movement of the forks is fixed then you should check for flat spots and over torqueing Move the handlebars left and right there should be no difference in the pressure It takes to move them as you go from left to right Worn bearings will often have a spot right in the middle that the bars want to stay in Overtightened bearings will not move smoothly If you cant find something in between the loose and tight adjustments that feels right then you need new bearings The bearings didn t go bad on my bike until about 30K and that was with the heavy loads put on it My clutch lever rattles when I rev the engine Duke Thu Aug 17 00 40 47 2000 Mine did the same thing a ringing above 8k used a 2 liter Coke bottle and cut a couple shims and slipped in like washers on the clutch lever and it fixed the problem I d imagine you could buy some very thin nylon washers at
101. e motor by turning the rear wheel grunt If the wheel turns then the motor is free and the starter Is the likely problem The battery and starter are OK so if you have starter fluid try using it if not go to 3 Starter fluid is a quick and easy check if everything but the fuel carbs are OK Spray the fluid into the carb openings read the can downstream of the air filter and try starting again If it fires up then you just need to drain the carb bowls and try fresh gas see 4 Check for spark Put the starter fluid can away Reach under the gas tank and pull one of the Spark plug wires with cap out of the head This is kind of a pain but quick enough and thus worth it to do especially if your bike sat in the damp Plug a spare spark plug into the cap hold the plug threads against bare metal of the bike If you don t have a spare plug put a metal screwdriver shaft down in the cap and put some part of the metal shaft up close to bare metal like 1 8 3 mm away Grab the screwdriver with a glove or rag if you don t want a little shock yourself Hit the starter button If you don t see a spark then there is some problem with the ignition likely a short somewhere If you do see spark then the problem is definitely with the fuel or carbs Put the spark plug wire and cap back on the plug in the head and go to 4 Drain and re fill the carb bowls Condensed water and dried fuel varnish can plug up the works enough to keep the bike from sta
102. e on BT45s took the bike to a track day and didn t have any problems but the dual compound rear showed more wear than would have thought but I m no expert The mechanic who put on my tires no bought them from another shop thought they were a good choice for aggressive riding He said that he would have sold them to me over the Dunlop K591s Dunlop K630 Duke Thu Sep 21 17 16 27 2000 Many folks have described how terrible the stock K630s are and admonish everyone else to throw them away and buy better tires for one haven t found the reason the 630s are so bad with exception of wet weather where they do slide around a bit But for dry riding they are just fine fully capable of peg scraping full lean turns Unless of course you are pushing at racing levels which very few of us are capable of doing at least I m not you will not feel them slide As far as the predictability of a slide drift I ve never really experienced much of a slide short of having low tire pressure at the Gap last weekend And even that front end push was not severe just enough to make me think was really sliding Point is the 630s are fine for all but the best of us They are also about 35 less expensive than other Dunlop tires Dunlop K591 Paul 311 Tue Feb 8 23 03 13 2000 On the race track there is no other choice in 16 tires but Dunlop K591 s Front 100 90 16 Rear 120 80 16 front tire or 130 90 16 There is no other combinatio
103. e the 15 cost of a tire swap and wear it down soon after decided that the tire is only worth about a K630 In the performance department if that Don t skimp and get one of these spend another 10 and get a good tire Bridgestone BT45 Jeff Sat Feb 19 00 59 16 2000 The BT45s were new last year and they fit the Ninja 100 90 front 130 90 rear Bridgestone markets the tires as geared towards mileage rather 58 than performance put a set on and the feedback is greatly improved as compared to the stock tires felt much more comfortable leaning the bike over as far as dared to the on BT45s took the bike to a track day and didn t have any problems but the dual compound rear showed more wear than would have thought but I m no expert The mechanic who put on my tires no bought them from another shop thought they were a good choice for aggressive riding He said that he would have sold them to me over the Dunlop K591s Dunlop K630 Duke Thu Sep 21 17 16 27 2000 Many folks have described how terrible the stock K630s are and admonish everyone else to throw them away and buy better tires for one haven t found the reason the 630s are so bad with exception of wet weather where they do slide around a bit But for dry riding they are just fine fully capable of peg scraping full lean turns Unless of course you are pushing at racing levels which very few of us are capable of doing at least I m not you will not feel
104. e you grow until you re 27 years old then you start to die Now what does respecting the engine mean Generally it s all about friction and lubrication Until the engine is run in there is more friction and less lubrication on critical parts valves cams rings bearings etc These parts must be in good shape for the engine to run efficiently and for long periods of time Exceed the proper RPMs and the unworn components will get too hot too fast you will get hardened rings scored cylinders and valves that do not seat correctly This may not make a huge difference at first but the increased wear will encourage more advanced wear Loss of compression noisy bearings leaking seals the list is extensive But it adds up to less power and shorter engine life span in the long run So again What is the proper respect What are the proper RPMs This is a matter of much disagreement But here is what is usually agreed upon Do not mess with an engine until it is fully 35 heated up fully lubricated and ready to be pushed No one will disagree that multiple progressive heat cycles are a Good Thing and that frequent oil changes early can never hurt Is there a formula for all this Not exactly but here s a good method would use make the engine work harder the more you break it in always keeping the temperature and friction inside in mind Example Start the motor and let it work up to running temperature Shut down and cool off
105. ean not lube motorcycle chains for a looong time and have never had a problem In fact my VFR s chain just turned 14 500 hard miles old has always been maintained this way and was pronounced as good as new by our local Honda experts just this afternoon How often should lube the chain what should use to do so Ninja Grrrl Tue Dec 7 16 58 02 1999 clean my chain and sprockets thoroughly with kerosene every 800 1000 miles and apply chain wax every 300 400 miles Chain wax comes In a spray can and is applied with a red tube fitted on the nozzle like WD 40 It Is just one method although a good one of keeping a chain lubed The chain should be warm like after a 10 minute ride and properly adjusted Spray the wax on the inside of the bottom run lubricating the rollers well NOTE Watch out you don t pinch your fingers between the chain and rear sprocket Wipe off the excess then wait about 20 30 minutes This allows the liquid carrier of the lubricant to evaporate leaving the chain waxed Yes kerosene is flammable but not nearly as much as gas or other solvents it s fumes are quite hard to ignite Gunk engine cleaner is similar As always use caution and youll be fine What are some good chain lubes Wolcott Sat Aug 18 09 02 58 2001 Motorcycle Consumer News just did a full test of a bunch of lubes Their best buy is PJ 1 Chain Lube black It got 25 points 4 Their recommended list is Yamaha Perfo
106. ecided to retire the Strada after 10k miles of daily use after a mishap with a nail and a plug that failed It still sits mounted on a rim fully inflated in the event of an emergency tons of tread still on it The BT45 is still going strong at 12k miles but I ll probably replace before the winter sets in Pirelli Sport Demon Brent Wed Apr 16 16 28 04 2003 Pirelli has a new tire option for the 250 ina 100 90 16 front and 130 90 16 rear It s the Sport Demon tire and seems to be marketed as a sporty touring tire It seems wedged between the MT66 which they list as a cruiser and the MT75 which they list as sport The MT75 treated me well so see no reason to why the Sport Demon would not perform well Three of the online tire dealers checked list this tire www mawonline com www discountmotorcycletire com and www denniskirk com they average around 160 pair Metzeler Daryl Mon Jan 3 15 55 24 2000 I ve gone through two rear and one front Metzeler tires and like them very well I m ordering a set here in a few weeks Front is a Lazer 100 90 16 Rear ME 55 130 90 16 get 20 000 miles from the front and 10 000 miles from the rear Best rain tires I ve ever used with good ride and very good feedback and grip It raises the bike a little with no tire clearance problems Michelin Jeb Sun Mar 6 01 35 27 2000 Michelin no longer makes tires that will fit the EX250 rims How do I determine tire size Duke Sat Apr 22 09
107. eees 75 What if I m just installing slipon canisters do I still need to rejet 0 eeeeeeeeees 76 Can I get a better exhaust sound without replacing the stock pipes ccccccsseeeeees 76 1 Want to ups rade ny SUSPENSION s 0 6ci tastes an E ones detaase ieee 76 5 YO DEE 0 6 E ee ne RT ene we aL Tm NCI Bene Ree Ete SNE CARRIO NE ere NTE en ae ee ee 76 How do I stiffen up the front suspension enossssoeeenessssseeeesesssssseeressssseseesressssssess 76 Where can I get some preload Spacers lonicerae a Ena E A T1 Will a fork brace improve the front suspension sssenenssssoseenesssssseseessssssseeresssss T1 Rear cnica a a a Gee katt mesenmnataabaateitaancuaane tices 11 How do Fehangse the tear shock terssnirinirar nee eee T1 How do Tadjust the rear preload at a RN 78 What kind of shocks are available for the 250R ccccccccccccssneeeccceceeeceeeeeeeeeeeeneees 78 Why should I upgrade my suspension e cc eeeeesececececeeneeseececececeaaeeseseeceesesaaaeneeeeees 79 How does modifying the steering geometry help ssnsnnnsssssssseenesssssssesreessssssseresssss 79 What good does reducing unsprung weight do ssennensssssseeresssssseserressssssesresssssssses 80 want to improve my Carburettor jetiNi ursann oe Meee Meee 80 Why would I want to change My Jetting sc ieccc sietuswensisvilande nr i AE 80 Howdolimproyvye my JO 7 susuriin iin N se ends dus E eee menus E 80 How CO Lets tall aje
108. een that is 2 taller than stock it is available only in smoke however have owned one of each and so have had a unique opportunity to line them up together and compare how they look OEM matching precision goes to the LP model which is shaped almost identically to the stock model The bolt holts are in just the right places and bolts in with no fuss The LP models are also a bit cheaper but available in only a few colors smoke purple and red The shape of the ZG windscreen is a little smoother more refined than the stock or LP windscreen It is less flat has a nice curvature to it and the corners are less square it looks a little nicer along side the LP model However the ZG model s bolt holes did not line up quite right with the fairing 100 holes It is due in part to the increased curvature that the holes were placed differently but they are definitely more difficult to align than they should be Due to mounting simplicity and cost savings might recommend getting the LP windscreen if you want a purple smoke or red one and getting the ZG model if you want a different color How do properly attach the windscreen to avoid breakage Jeb Mon Jul 2 16 37 53 2001 It is important to put bolts in the center two holes first loosely then the two holes beside those etc until you ve worked your way around the screen Do not use any type of wrench hand tighten only Gradually tighten the centermost bolts a bit then the
109. else in the manual it says that the intakes are 0 10mm and exhaust 0 13mm Anything in the range listed is probably okay but always make sure mine are set to a consistent number The valve clearances are the same for all 250 Ninja s Are there any advantages to selecting a specific setting within that range Lou Sat Mar 25 02 31 12 2000 The valve clearances affect valve timing and overlap the period that both intake and exhaust valves are open With everything stock on the bike the maximum amount of air gets trapped in the cylinder at about 9 grand peak torque Before 9 grand the overlap actually lets a little air go backwards through the intake valve before it closes reducing the amount for combustion After 9 grand the valves are opening and closing too fast so less air goes in per cycle One way to shift this slightly is with the valve clearance If the clearance is at the minimum the overlap will be more and the valves will open more This shifts peak torque and therefore peak horsepower up slightly at the cost of low to midrange performance 45 If the clearance is at the maximum the overlap is less so it will trap the most air in the cylinder at a lower rpm boosting the low to midrange but at the cost of the higher rpms because the valves arent opening as far Having the valve clearance at its maximum also allows the valves to stay in contact with the valve seat longer transferring heat during that time and he
110. em The EX250 has soft pot metal that bend easily bars that bolt into risers bolted to the top triple clamp For a better idea of what I m talking about look at the parts microfiche for the EX250 on www buykawasaki com then look at a bike with real clip ons like the ZX6 R Many new riders do not like the low position clip ons provide since you need to build up muscles in your arms back and wrist to get used to it The 250 s position is much more comfortable for new riders and shorties How does a carburettor work Duke Wed Jul 5 22 35 52 2000 The Ninja uses a Constant Velocity Carburettor which means the velocity speed the air flows through the carb remains constant however the volume of air moving through changes as the slide raises It s a mutual relationship the more air is drawn through the more vacuum there is to pull up on the diaphragm thus raising the slide and allowing a greater volume of air through The actual throttle cable is connected to a metal butterfly valve which resides in the carb throat just inside the slide As the butterfly opens more air is allowed to enter The Jet Needle which is 31 attached to the bottom of the slide raises out of the Needle J et as the slide raises Thus more air gt more gas The needle has a precise taper to it being thick at the top and thin at the bottom This taper is crucial to the bike having good power through the RPM range This is where all the money Is spent b
111. er pay 105 per year for comprehensive insurance with a low deductible This along with a little bit of depreciation and lost interest on my cash is my only expense to own this bike figure it all adds up to about 500 year or 40 per month about my cable TV bill This is by far the most riding satisfaction can get at anywhere near these prices Period I ve got the cash on hand to go by a huge sportbike but don t like to waste money like to have fun can do that on a 250 Ninja as well as can on anything else If rode 8 000 miles year or more might make the investment in a 600cc but as a pleasure rider with 2 kids college to still plan for I ll take the 250 any day On a pretty day on a windy country road my 3 299 buys me all the riding fun I ll ever want or need If you want to go 0 60 in 3 seconds and top out at 160 mph good luck to you just want to ride have fun and come back in one piece to my family By the way Know a lot of these macho guys are the same ones who go out with t shirts and shorts and no helmets If you crash you re going to be so messed up you ll never want to see a 750 600 or even a 250 ever again Not many guys or girls who have gone through 3 months of Skin grafts ever want to sit back on a bike wear Draggin eans gloves leather jacket and a Snell rated helmet All of that cost me 350 My body s worth thousands of times more than that Good luck daredevils Pay your 7 000 and
112. er hero like and is generally more lightweight and comfortable The best cordura suits like Leon s aerostich are certainly better than a cheap leather ensemble Cordura clothing can be just as well padded as leather and carry the same armor have a leather jacket and wear cordura pants over my regular pants The leather jacket probably gives me a little more peace of mind but still value the extra protection of the pants Again leather will tend perform better in a crash and cordura will perform better in everyday use You have to get what suits you best Pants Joe Rocket Ballistic Pants Wes Tue May 16 15 15 01 2000 They are a little loose but very adjustable had to get Large because have a 34 inseam and the medium was just too short This means that I m wearing pants meant to fit like a 36 40 waist but it isn t too bad just had them altered to pull tighter on the elastic They also have a Velcro belt that you do up The pocket above your left knee is quite big and very convenient The stiff pads at the knees should give good protection they are the same as the elbows in my jacket and soft pads in the hip give some padding but don t restrict your mobility at all Of course you still have the abrasion resistance from the 110 ballistic nylon They are quite waterproof and go over other clothing easily as they have zippers up the legs They also will zip into Joe Rocket Blaster or Ballistic jackets When am
113. er rode before me being one of them We had an experienced rider dump it during the Maximum Breaking exercise Some of the experienced riders had tight cornering problems too say if you want to sharpen your skills and become a more alert and aware rider the course is the way to go It s too bad all states don t require this or a simular course before issuing a motorcycle endorsement on their licenses J ust my two cents What are some good riding techniques Basic Controls Jeb Sat Apr 22 02 17 56 2000 It goes like this e Left hand lever clutch e Right hand lever front brake e Right hand grip throttle e Left foot lever gearshift from neutral down once is 1st gear and up five times will put you In sixth e Right foot pedal rear brake 24 Turning and leaning Speed control Che FriJan 21 06 22 29 2000 The key thing here is to slow down before you start turning While you are still going straight get the bike slowed down to a speed you feel comfortable going around the corner at Now let off of the brakes especially the front and as you start to make your turn you need to also gradually accelerate too Increasing your speed slightly throughout the turn will add stability to your bike If you slow down while you turn the bike s dynamics get worse not better Looking through the curve HJ Sat Jan 22 16 36 33 2000 Look where you want to go That would either be the exit of the curve turn or as far up as
114. ess and can pull in the clutch to drop down the last few gears as come to a stop With practice you can put it back in neutral before putting your foot down When accelerating you can pretty much downshift whenever you want a power boost However downshifting when doing anything over 11k rpm is pretty pointless as you re already in your powerband You want to try to downshift to keep revs between 9 and 12k this is where you get the most tug for each twist of the wrist You should to let off the throttle momentarily while quickly 28 disengaging the clutch and kicking it down then opening the throttle up wide to match engine speed as you release the clutch lever again this will give you the power you need to accelerate effectively Clutchless shifting VFR Pilot Thu Mar 2 11 42 15 2000 Clutchless shifting can easily be done on a motorcycle it s just a matter of matching the rpms On upshifts it s just a matter of backing off the throttle for an instant as you bang the box into the next gear On downshifts you have to rev the engine up a bit as you drop a gear Of course the clutch is there for a reason and shifting without it will wear your tranny out more quickly In short the only place this technique really has is on the racetrack where tiny fractions of a second can make the difference between first and second place My advice Learn how to do it and then don t unless some large person named Mad Dog Al is chasing you with a c
115. et clean of oil and put everything back together carefully when done Use very little torque on the valve cover bolts the book calls for 87 in lbs if you don t have a torque wrench then tighten them by hand followed by a 1 8 turn with a 10 mm wrench to seat them 44 ls there a special tool to make this easier Jeb Wed May 16 01 23 32 34 2001 Here are a couple of pics of the adjuster tool from Kawasaki part number 57001 1220 It s not cheap at 35 but it does make the job a lot easier It s basically just a low profile 9mm 12 point socket welded to an extension that is just the right length a with a hollow shaft so the matching screwdriver can be inserted through it It helps because there are no sockets to lose into the top end and it allows less work to get the adjustment correct without changing the adjuster setting while tightening the retainer nut would recommend it if you plan on doing all of the adjustments yourself Kawi also sells a special feeler gauge 57001 1221 which has the maximum and minimum clearance thicknesses on it it gets pushed in and when the thin end goes but the thick end won t the valves are set For 40 it s not really worth it though use a standard set of gauges from Sears that cost less than 10 What are the acceptable clearance ranges Paul 311 Sun Mar 5 17 05 48 2000 08mm 13mm for the intake valve clearance llmm 16mm for the exhaust valve clearance think somewhere
116. et grips Some are really comfortable and not expensive Your local shop will have the glue to re do them 89 The lever mounts etc are held in place by fasters don t remember if they re phillips or allens but will be metric Use the appropriate correct tool to loosen them or you ll strip the fasteners Reinstall them on your clip ons in reverse order Be sure the clip on position is such that they don t hit the tank or faring The main thing to worry about is routing of the cables and brake lines Be sure they don t bind or rub on anything After it s back together run the engine and make sure the throttle doesn t change when you turn the bars to full lock in both directions If it does adjust the throttle cable route until it doesnt Not difficult but use the right tools I want to change my gearing How do I change my gearing Gazoo Sun Mar 5 19 26 22 2000 For about 50 you can get some new sprockets for the Ninja 250 that will lower the RPM s at highway speeds better mileage On a stock Ninja the front sprocket has 14 teeth and the rear sprocket has 45 teeth Replace the front with a 15 tooth sprocket JT Sprocket Part 24 8637 or PBI Sprocket Part 456 15 Special order from a dealer and or Replace the rear with a 42 tooth sprocket Sunstar Denniskirk com Part 80 017 42S Does installing a new front sprocket make a significant difference Jeb Thu Mar 9 14 24 16 2000 Changing the countershaft gear
117. etting harder to find 100 80 and 130 80 tires though so it s good to know what the other options are Taller tires alter your steering geometry this can be good or bad depending on which tire you change A taller rear tire will steepen decrease the geometry making the bike turn faster a taller front will increase the steering angle Increasing both front and rear tire heights can be good because you get an even steering angle close to stock and get added road clearance and trail length provides stability A taller rear tire will also increase the final drive gearing a bit lowering cruising revs while a taller front will increase soeedometer accuracy Wider tires generally slow the steering of the bike down They also alter the contact patch as the tire is pinched in the rim Wider tires can provide better straight non leaning traction Wider tires are necessary when carrying heavy loads or if the bike makes a lot of power the EX250 typically does neither of these things so wider tires are usually of no benefit Taller and wider tires both weigh more so you have additional unsprung weight to deal with slows down suspension action Considering all of these points use a 90 profile front tire on my bike with a 120 80 tire on the back and suspension setup that offsets these changes lower front suspension higher rear This provides the best performance and handling in my opinion Do 120 width tires really work better
118. f riders who ve either never used a modulator or are afraid that using them will just annoy other drivers instead of alerting them and lead to a more anti biker attitude on the part of the general public And suppose that if we all left our modulators blinking all of the time that might well be the case But when used sparingly as they re intended to be used think that a modulator can significantly improve your safety on a bike When car drivers who ve been involved in car bike accidents are interviewed they nearly always say that they just didn t see the bike A modulator can make that happen a lot less frequently I want to wire extra brake lights into those empty rear sockets ITM Sat Feb 12 15 46 22 2000 It s very easy to do It s also a good idea to add extra brake lights as well in the case that your one and only brake light goes out Makes you more noticeable when stopped with your brakes on e Goto autozone and pick up a couple of double contact sockets part 85803 made by conduct tite e Runa ground wire to each socket solder or tape in place e Runa power wire from each socket to the brake light circuit and accessory or tail light circuit wires blue and red It s very simple to do It s cheap probably under 6 and it makes the back of the bike look bigger gets rid of that old small moped look want to make the stock front flasher pods into DRL s Jeb Sat Jul 1 12 13 31 2000 Daytime Running Lamps increase t
119. ff carbs Take apart Spray carb cleaner inside Put back together Okay now for the long version Once you have the carbs out of the bike turn them upside down and remove the phillips head screws and take off the float bowls Inside are two floats each connected to a float valve that allows fuel into the float bowl When full the float valve shuts off the fuel supply just like the float in a toilet tank With some needle nose pliers gently pull the pin out that holds in the floats and remove along with the float valve plugs Now remove the tops of each carb and carefully remove the slides jet needles Be very careful with the rubber diaphragms which are very fragile Once everything is apart use a can of carb cleaner spray available at any Wal Mart K Mart etc think used the B 26 Chemtool last time to thoroughly clean the inside of the carbs Be sure you get the can with the little tube on the nozzle so you Can spray it in all the little spots in your carbs Spray cleaner through every jet you can possibly find Be careful you don t get the cleaner on any plastic parts on your workbench it will melt them I learned the hard way sorry dad Do not use any sharp objects when cleaning carbs the pressurized spray works fine Also you can clean the tips of the float valve plugs by rubbing against a piece of cloth The tip is rubber inspect for damage Once clean inspect everything and put it all back together You can get the ca
120. fluid drop the springs in and cap em off Put your bike back together and ride away happy How do service electrical components How do replace the headlight r eon Thu Jul 13 18 54 40 2000 Pull the wiring plug off first then the dust cover the bulb is held in place with a little wire retainer The bulb pulls straight out the back once the retainer is loose It is much easier to do all this with the whole assembly removed from the bike 55 think the factory puts some extra paint or other goop to keep the light glare from escaping back into the fairing With the fairing off you should be able to see where some of that got scraped off Some more rubbery black paint should stop that extra light from escaping How do I adjust the headlight beam Vernon Dozier Sat Jul 27 20 48 39 2002 Look at the back of the headlight See the white plastic pieces in the upper right hand and lower left hand corners Those are the guides to adjust your headlight aim The vertical adjuster is the one on the lower left corner and the horizontal is the other Stick a phillips screwdriver in the guide from the bottom and turn the screw that can t be seen You re turning a screw not trying to pry the guides off Those plastic pieces are just guides for the screwdriver What kind of battery should use Jeb Tue Dec 18 18 45 14 2001 After over 3 years and 27 000 miles of service my stock Yuasa YTX7L BS finally stopped retaining a consisten
121. for a 110 and a 120 Worked great It took nearly 100 hours of measurements and calculations to figure out what to tell the machinist to do to the wheels and Spacers to make it all fit wheels centered etc Cost was about 800 before buying the tires EX500 wheels won t bolt right up You can use your stock axles but that s about it The spacers are wrong the sprocket is in the wrong location Both rotors are in the wrong location The rotors are a different size so the callipers are in the wrong location have drawings which show what needs to be machined but the end cost is still exactly what paid Yes it s easier to do a second set but the only part you d get to skip are the measurements and calculations and didn t pay anything for that part since did it myself paid 250 for a set of wheels including rotors which didn t need and hardware spacers and cush drive which had machined down Anyone interested in going to 17 wheels is probably better off getting a set of 16 wheels welded up by Kosman they are the ones that did the machining work on the EX500 wheels too 94 Unless you re going to race it s not worth it Even if you are going to race it s still probably not worth it Security Disc lock VFR Pilot Fri Tue Feb 22 01 03 46 2000 Disc locks are good while temporarily parked in plain sight during the day but they can t prevent a determined pair of thugs from picking the bike up and tossing it in the b
122. from a 14 to 15 tooth sprocket is the most common gearing mod and it does make quite a difference At first thought the bike seemed sluggish after changing mine the torqueyness was used to wasn t really there As rode around town for awhile it seemed the bike just wasn t revving as quickly as it used to this of course was to be expected since the countershaft was working harder But soon realized that the change in acceleration was marginal though the bike was taking longer to rev through the gears each gear was putting out 7 more travel per revolution So the twist on throttle has to be a little greater now to get a satisfying 0 60 run but the high speed cruising has been improved noticeably Twice today thought was already in 6th when was still in 5th It wasn t too difficult a task loosen the rear wheel remove the countershaft housing remove the 14 tooth sprocket put the new sprocket in torque the retainer bolts replace housing set correct tension to chain and torque rear wheel and clean wax the chain The sprocket switch took about an hour overall just followed the process as outlined in the service manual Popping the old sprocket off was a snap putting the new one on took a bit because the countershaft teeth are cut to very close tolerances Cost 15 90 Is there any advantage to installing a smaller front sprocket Paul 311 Tue Dec 11 20 49 30 2001 tried a 13 tooth front on the track for a little w
123. gap it might not be the fastest but it s great fun without the pressure In heavy traffic love passing ZX9 s and CBRs Can t keep up with the mopeds though those guys are crazy 111 Misadventures Dealing with risks Leon Fri Apr 28 04 43 16 2000 Motorcycle accidents happen for a variety of reasons all can be prevented simply by not riding If you ride you face the probability of having an accident You can change that probability but can not make it go away unless you quit riding have fallen on my Ninja 250 twice Both were my fault Most recently the chain jumped the sprocket and got caught between the swingarm and sprocket was riding at roughly 10 mph while going around a corner when it happened was two blocks from home and hoped to make it the rest of the way Yes it was my fault yes was pushing it too far and given the same situation would do it again The other time was backing out of the driveway with two inches of snow on the ground The rear tire made contact with the sloped edge and slid sideways slipped when trying to catch it and fell down was straddle walking it backwards at the time how much slower should have been going It was my fault was pushing it too far and have done that again several times without incident In Washington DC a few years ago made the mistake of stopping as the light turned from yellow to red was rear ended hard enough to get knocked in to the middle of the in
124. gear like the Firstgear and cheap AGV suits are actually just flimsy foam rubber of limited use in an accident Good armor will save you weeks of pain and suffering and may even save a limb or your spine The next most important factor is comfort If your gear is unwearable and impractical it won t do you any good because it s hanging in the closet or strapped to the back of the bike You can break down comfort into two categories fit and temperature control The fit should be comfortable when you are on your bike The tiniest irritation can swell into a big pain after a few hours in the same position Also the clothing should not balloon at high speeds that can add to fatigue Leathers need to be skin tight for the best abrasion resistance since the leather can give you a burn when it moves on your skin in a crash 21 Your suit should be comfortable over the range of temperatures you ride in again your gear won t protect you if you dont wear it Leathers should be perforated to flow air and nylon suits should have lots of vents Buy your textile suit loose enough for a layer or two underneath in cold weather and you can layer over your leathers with a windbreaker or raingear for those chilly Sunday mornings Why is style important Well dont know about you but if wanted to look like a special ed student I d trade my Ninja for a short yellow bus Pick gear that reflects your tastes and fashion sense This is less important for us
125. good company and have one of those It s not cheap but neither is missing 3 weeks of work because of broken ribs Do really need to wear all this stuff Gabe846 Tue Jun 27 23 39 17 2000 People don t wear protective gear because they are ignorant crazy or both It s a simple rule to learn Before you get on your bike look down at yourself and ask Am ready to crash If the answer is no then don t ride Easy as that You ll either learn the easy way by listening to me or learn the hard way by experiencing excruciating pain or permanent injury Most of those guys you see are waiting to learn the hard way After they learn the hard way they inevitably give up motorcycling for good Too dangerous they say And for them they re right This is no place for idiotic irresponsible people and they are better off playing golf So what will it be for you EX250 or a 9 iron What factors should consider when looking for these items Gabe846 Mon Jan 22 00 15 55 2001 I ve preached about riding gear a lot and think 4 crashes in a year most on the race track qualifies me to say a few words about what you should wear while riding First of all let us be clear about one thing crashing is an unplanned event and that s why vehicular mishaps are called accidents Therefore you should assume that a crash could happen at any time whether you re in the corkscrew at Laguna or riding down to the corner for the proverbial quart of
126. h it as it gets squeezed out Tighten each side one turn as a time until you just can t do it anymore more at this point the clamp turn bars may be bent from the torque and there should be a good mm of pin exposed Remove the clamps If you have a riveting master link then take the biggest hammer you have and put it behind the link Using another hammer repeatedly hit each pin until it mushrooms out to about the size of the other rivets it may take a while If you have a clip type link use needle nose pliers to carefully pop on the clip Keep some spare clips on you and check the chain at every gas stop 42 Another option is to buy an endless chain without a master link and drop the swingarm If you ve had the swingarm off before and are comfortable with the procedure then this method of replacement may actually save time over the above options What replacement chain sprockets should consider Dweedlebug Thu Feb 22 08 47 48 2001 As far as the best chains out there don t think anything really comes close to the DID ERV2 Gold X ring It has superior tensile strength and excellent lubrication properties There is a guy that runs the DID ERV2 on his turbo R1 without any hint of failure would think any decent parts supplier whether locally or on the web could get you the 520 106 chain you need would not trust any other type of brand other than a DID You may not want to cough up the dosh for the ERV2 as it is not cheap
127. h the DRL mod 102 Personal Accounts Choosing the Ninja 250 Wanted a bike for years Craig Thu Jan 20 18 09 34 2000 Pull up a seat It all started about 20 years ago as a young adult had a burning desire to buy a motorcycle Back then Honda s were pretty cool But alas my dreams were squished by my inability to afford both a car and a bike Then got myself married some 13 years ago Went once with the wife after getting married and drooled all over all the local iron Still couldn t justify the cost seeing I d only be able to ride a few months out of the year living in RI Having gone through the spring ritual bothering dealers and recalculating the finances for several uneventful years flash to 1999 was bitten by the bug and infected Was positive it would be a cruiser sport bikes are only for wannabe angels kept telling myself J ustified the cost with the wife but honey I m going to be saving so much by not buying another car yada yada yada Gained her approval finally in September Had my heart set on a Marauder until seen a V Star Custom was lust at first sight Figured I d check out the Shadow s at least a check see anyway no go What s that over in the corner a smaller sportbike Hey this thing fits like a glove no weight and balance problems here Dual exhaust like the symmetrical look of dual exhaust a tach temp gauge hey did mention it fit like a glove It was like putting on your favorite pa
128. h your arms out to where the handlebars should be Handlebars from an EX500 can be trimmed and fit on the 250 that will make them a bit taller there are also some kits to adapt standard handlebars Storz Performance Products makes one the bolts spacing for the Concours is the same as the Ninja 250 but don t know if the kit will work on the 250 Rear shock The EX500 shock is a good economical choice 93 On longer rides make sure you stretch regularly Don t grip the bars any tighter than needed to maintain control If you re too far forward and have some of your weight on the bars that also causes fatigue A larger windscreen removes the fatigue caused by the wind beating you around but it also removes the lifting forces that takes some of the weight off your hands Email if you have additional questions I m currently building a ZX6 touring bike for a trip to Alaska this summer I d like to get some new grips Jeb Thu Aug 31 15 24 41 2000 Go to any bike shop and you can find a good pair of replacement grips for 6 12 use a set of Pro Grip brand waffle grips these have a good texture and nice rubber gel composite material which is much more comfy than the stock items Duke has some Oury brand grips that he likes a lot The hardest part of installation is getting those damn bars ends and their phillips head screws out you may need an impact driver heat them up or drill them out Once they re out replace the screws w
129. hainsaw Shifting when stopped Barry Fri Nov 17 09 10 36 2000 It s completely normal to have trouble getting the bike into first from a higher gear when stopped from time to time it happens to me What I do is this When stopped in a gear higher than first press down on the shift lever if the bike goes into the next lower gear fine If not slowly let out the clutch till you feel the engine just start to move the bike then pull in the clutch and press down on the shift lever The bike will then go into the next lower gear Repeat as necessary till you get to first Rocking the bike back and forth works but for me this method takes less effort and think its probably faster Braking Using front and rear brake gabe846 Wed May 3 17 50 23 2000 You have to overcome the car derived impulse to mash the brake pedal with all your might in a panic situation That s going to mean a rear wheel skid and then a highside when you release the back brake Learning to ride well is all about suppressing your survival instincts and replacing them with new ones One of them is to not tense up and clamp down on everything in an emergency situation Smooth progressive braking will save your ass most of the time Your front brake gives you 80 of your stopping power As you brake harder weight transfers to the front of the bike compressing the forks except telelever BMW S and taking weight off the back wheel giving the rear tire even less tract
130. hat every EX500 racer in the world has a stock shock gathering dust in his garage The main difference between an EX500 shock and a stock shock is probably the ride height of the rear end of the bike When you jack up the back a little you make the head angle steeper and it makes the bike steer more quickly and also puts more weight on the front end Another way to get the same effect is to loosen the triple clamps let the forks slide upwards until they stop against the bar risers then re tighten the triple clamps be sure to use a torque wrench for this as the top clamp Is aluminum For real rear end performance you can send your stock shock off to Aftershocks in Palo Alto CA 650 494 8849 or buy a Works Performance shock use an Aftershocks valved WP shock on my Race bike the WP shock will also make the rear end taller You can get a Works Performance shock for the Ninja for about 300 new They aren t adjustable except for preload use one now on my race bike and it s a decent shock for the money Aftershocks can re valve these to make them work better too though Aftershocks may be able to re valve your stock shocks have seen people racing on a re valved stock shocks and they seemed to work ok too Why should upgrade my suspension Wolcott Fri Nov 19 20 10 55 1999 Suspension makes your cornering possible With a lousy suspension you never feel comfortable enough to really lean it over and get on the gas With good suspension
131. haust of fuel mists causing incomplete combustion and further deposits Eventually valves may stick or the sharp edges or hardened deposits may cause hot spots and damaging preignition Rather than waiting for an engine rebuild to clean the valves a simple treatment process can be used every 15000 miles or so to keep the system relatively clean Basically a valve cleaning solution is fed directly into the intake manifold of a hot running engine this hot soak quickly breaks up deposits For this job a 3 length of 1 4 I D clear tubing a 1 4 O D T fitting and a bottle of valve cleaner are needed Cut a few pieces of the tubing off and use the T fitting to make a configuration like this __ After warming up the bike kill the engine and pull the intake manifold vacuum hoses then connect the T hoses to the nozzles Put the other end of the hose into the bottle of cleaner and use a small vise grip or clamp to close it Start the engine and turn up the idle to 2K RPM Slowly release clamp pressure so that the cleaner is drawn up into the engine do not let too much be taken in at once or the engine will stall It is normal to see a white smoke exiting the exhaust pipe After several minutes the engine will start to labor as the carb bowls become empty For a longer interval the free hose connected to the tank petcock can be reattached to one of the intake nozzles to refill the bowls When the intende
132. he assembly 101 The first shows how the unit looks when installed the other has the unit pulled so you can see the mounting holes There s only a bit of space at the back that is left when installing them so didn t worry about it You could bondo over the recess and repaint if you wanted You ll notice there are two posts on the back of the unit One of these fits right into the stock front mounting hole second hole from the front don t know what the very front hole is for may have drilled that one for some reason but don t remember The second hole had to drill to fit the rear mounting post it s the small hole in front of the large hole near the back of the indention There is also a v shaped piece I cut out of the very large hole that would normally accommodate the stock pod post this is to allow the wires to be slipped in and not get crimped by the unit when it is attached on the back side of the fairing each post is held in place with a washer and a 9mm nut included think with the unit To attach mine had to remove the rubber base of the new lamp assy to get it to fit into the stock recess Be careful when drilling the fairing It doesn t take much force to go through that plastic There are only two wires to worry about the red one goes to the green gray hot wire and the black one goes to the black yellow ground wire Installation takes about 15 minutes for the pair These look really good when combined wit
133. he frontal visibility of the Te a rw bike during the day At night they also help by placing an Wiring dia ram amber light on each side of the headlight making it hatta i obvious that a motorcycle is approaching and not a car bottom view with all but one headlight out To make a set of your own go to Radio Shack and get a few 275 248A 12V relays blue base pick up a few feet of light gauge wire while you re there If you don t have a soldering iron you can pick up a soldering kit for 5 10 as well You ll want to solder four wires of about 3 to each of four of the pins above these will then be attached to wires on the bike to complete the circuit Soldering them directly to the bike is more solid but more difficult use the short wire method if you haven t soldered before so you can m easily access your workspace Use different color wires to NO NC make it easier oie The stock flasher hot wi ing f the batt Normally Normally e The stock flasher hot wire coming from the battery side goes to the red pin open closed e A constant wire that you ll have to run yourself will be connected to the blue pin I used the tail light harness but I m sure there s an easier one to get to in the front you need to pick one that is on when the ignition is in on or park positions 97 e Connect the yellow terminal to the hot wire coming from the bulb unit e Remove a bit of insulation from the stock ground wire a
134. he rear are the same as before 130 90 16 or 120 80 16 He did comment that the larger front tire made the bike steer more slowly think the increased tire size and the pinched profile probably offset each other so the contact patch is about the same Robert did his best ever lap times on these tires Sunday He had to lower the front end a little to make the bike turn in more quickly in order to compensate for the fatter tire Robert used these tires to just barely beat me my trick wheels and my trick Dunlop D207GP and GP tires Skill wins over technology again Kenda Jeb Wed Sept 5 10 23 22 2003 The Kenda K657 Challenger and K671 Cruiser tires are both decent quality tires with solid grip good water dispersion and neutral profile They are inexpensive a little over 100 a pair and come in 100 90 and 130 90 sizes for front and rear respectively These tires are heavy 6 ply units that are best used for touring in my opinion They don t match the quality of Metzeler touring tires but are cost effective with good tread wear and can handle heavy loads Pirelli MT75 Jeb Fri Sept 5 10 49 59 2003 If you re looking for an inexpensive sporty replacement for the stock tires this is it IMHO The Pirelli MT75 s are cheap about 100 pair offer good treadwear about the same as stock excellent grip not quite as good as GT501 s but still very good and light weight less unsprung weight means better suspension response These
135. hift from neutral into first because there is not enough oil between the plates for them to slip 36 You can avoid the bike jerking by pulling in the clutch after you start the bike and then holding in the clutch while the engine warms up If the oil is cold pumping the clutch a few times isn t enough After the bike has been fully broken in after say at least 5000 miles you could switch to a synthetic oil that will lessen the tendency of the bike to jump forward Why does my bike take so long to reach normal running temperature Jeb Sat Jan 27 8 51 48 2001 The ninja runs cool the temperature needle will normally stay very close to the cool end of the normal range After startup don t wait for the bike to warm up at idle this will take too long waste fuel and encourage carbon buildup on the valves and spark plugs Instead start it up give the engine a few moments to get into the rhythm then ride away Do not apply excessive throttle or make sudden throttle changes be smooth Keep the tacho below 6k until the needle is over the cold mark and then below 9k until it has reached the normal range 6k and 9k are my limits you must choose what works best for you Riding the bike will help it warm up much more quickly Additionally during the colder months a piece of cardboard can be placed over front of the radiator to partially cover it this will make the radiator less efficient and increase the rate of heat build up If after
136. hile It makes it harder to keep lube on the chain because the chain is turning a tighter corner Also the chain eats into the keeper even if you file it Waaaay back The only advantage is a lower first gear b puts ratios closer together Aside from that it s all the Same because you end up in 3rd when you would normally be in 2nd etc What drive ratios are attainable Paul 311 Wed Dec 15 07 20 34 1999 have a few sets of gearing for my race Ninja Using 14 47 works well at the three tracks race This weekend I m heading to Willow Springs raceway to do some off season racing testing I ll probably use the 15 tooth front sprocket since hear you spend a lot of time WFO at Willow Changing the front sprockets is easy and doesn t take a whole lot of chain adjustment The rear sprocket on the other hand may require links to be added or removed from your chain Here are some gear configurations and their respective final drive ratios 15 42 35714 14 42 33333 13 42 30952 15 45 33333 14 45 31111 13 45 28889 15 46 32608 14 46 30435 13 46 28261 15 47 31915 TAJAT a2 lol errs 13 47 27660 I just want more power Leon Thu Apr 27 13 31 01 2000 How much HP do you want e 1 5 Exhaust pipe intake and jet kit e 3 8 Porting compression cams e 20 trade the Ninja 250 for a bigger bike The most economical of these is the trade You can get a good used 600 or a superbike in fair condition for the
137. his happens because the tire suddenly has a loose spot 2 Wet the entire bead with some soapy water nice lubricant Use an iron to pry the tire bead of one side of the tire over the rim lip 3 Using the other two irons leap frog around the rim prying the bead over the lip Repeat until the entire bead for one side of the tire is off the rim 4 Now turn the tire over Using the iron push the opposite side the side of the tire you didn t work on over the rim lip the same lip you just did work on 5 Leapfrog again to get the whole thing off Congratulations The tire is off Now time to reinstall Remove all balancing weights from the rim Soap water up the beads again not too much this time Using your hands and body weight push the entire one side of the tire over the rim tire should now look like it did after step 3 above Using the tire irons rim savers and leapfrogging push the other bead over the same lip this can be very physically demanding its a very tight fit Now the entire tire should be properly sitting inside the rim lips It will looks oose however because the bead hasn t been set This can be tough 1 Remove the valve stem cap 2 Using an air compressor the good kind with the tank not the little thing you plug in your cigarette lighter if you don t have one go to the gas station that has one pump 40 60 pounds into the stem praying the bead will set you ll know this because you
138. hit the ground and snapped the fairing got a tube of putty type marine epoxy at an auto parts place It says it is good for plastic and will set in any conditions formed it to match the hole and sanded it smooth but knew could never get the paint right so got a Targa upper fairing bra to totally cover it The repaired patch is probably stronger than the original plastic am by no means a professional at this but with the bra on you can t tell it was ever damaged like that epoxy stuff better than body putty kits you can just form it like you want like using play doh I m trying to find touch up paint to cover some scratches Spoon Sun Nov 28 16 42 18 1999 PJ 1 colormatches are damn close it ll take fewer coats with primer underneath available at dennis kirk and most cycle shops I m not sure how available Kawasaki white is PJ 1 makes OEM matches for most every cycle maybe something will be close minor scratches can be taken out with buffing compound and then waxed with something like Nu Finish My bike was wrecked but it wasn t my fault Chris Wed Nov 10 20 01 16 1999 The best thing you can do in this case is take the bike to your local dealer and have them do a damage estimate They will use factory part numbers and prices Take the estimate to the insurance company Do not deal with the person who hit the bike he is out of the loop now The insurance company will cut you a check and you can decide what needs to
139. ick to the road and are also relatively inexpensive and in my opinion outperform and outlast Metzlers and K591 s they are very popular with European racers My ex husband races them at Mosport in Ontario on his TZ250 had them on my RG500 Gamma and the bike held the road like a fly on flypaper while lasting over 20 000 KM with lots of rubber left when sold the bike And ask anyone at the flying saucer in Niagara Falls rode my gamma hard Cheng Shin Jeb Wed Aug 16 06 02 30 2000 Cheng Shin tires are what you might call a value line of tires The thing is they re not that much cheaper than a good set of Dunlops not cheap enough to justify their lack of grip anyway 84 bought a new used set of wheels and one of them came with a Cheng Shin tire still on it thought Heck it still has a few miles left on it and so decided to save the 15 cost of a tire swap and wear it down soon after decided that the tire is only worth about a K630 In the performance department if that Don t skimp and get one of these spend another 10 and get a good tire Bridgestone BT45 Jeff Sat Feb 19 00 59 16 2000 The BT45s were new last year and they fit the Ninja 100 90 front 130 90 rear Bridgestone markets the tires as geared towards mileage rather than performance put a set on and the feedback is greatly improved as compared to the stock tires felt much more comfortable leaning the bike over as far as dared to th
140. ike to accelerate all the way through a corner rather than try to trail brake up to the apex and then accelerate That soft suspension again Altogether the little Ninja did a pretty good job on a very challenging road that will show up the weaknesses in any bike The day was beautiful the road was full of sportbikes and Harley riders the leaves were in full color and even hooked up with a friendly Ducati rider and stayed with him for most of the downhill homeward run Until we finally got to a straightaway 107 1500 Miles in 24 Hours Leon Wed Jan 12 14 55 31 2000 went to Florida and bought some oranges Saturday the bike ran good A low tire at about the 400 mile mark added a few minutes to the trip and hurt the fuel mileage too didn t check it before left d oh A wire to one of my electric gloves broke but it wasn t cold enough to really need them The idle isn t correct now so I ll have to adjust the valves this weekend The Ninja 250 is a decent bike for taking trips Statistics Location Time Odometer Fuel MPG MPH Dale City VA 2 23 76432 N A N A N A Wilson NC 5 31 76659 4 964 45 7 72 4 Florence SC 8 06 76812 3 34 45 8 59 2 Pooler GA 10 39 76997 3 718 49 8 72 5 Live Oak FL 13 53 77211 4 128 51 8 66 2 Hardeeville 17 18 77444 4 775 48 8 68 2 SC St Pauls NC 20 52 77670 4 65 48 6 63 4 Emporia VA 23 15 71832 3 317 48 8 68 0 Dale City VA 1 51 77984 2 381 63
141. ile and fits beneath the carbs The part is 2 50 USD and the element can be replaced as well for a little less replace mine with every oil change Alternatively you can install a 14 or so hose and point it at the drivechain then your blowby will lube your chain How do I make use of the extra space under the seat Jeb Sat Sep 29 15 52 18 2001 I ve spent the last few weeks looking for a storage box of the right size that could be put under the seat between the battery and K amp N s to use the space made available from removing the airbox finally found the right item at a K Mart after checking a few hardware stores looking at mailboxes plastic box planters small parts bins etc it s an ordinary 2 file box for 4 x 6 index cards The box is just the right size well it could be an inch deeper but it works well enough simply removed the flip top lid drilled a hole in each top corner and used some zip ties to suspend it from inside the frame of the bike just below the bracket at the rear of the gas tank A 4 x 4 x 6 box isnt huge but every bit helps There s not a lot you can do with the space otherwise since the drive chain and rear suspension are directly beneath that spot I m thinking about getting new tires What tire makes are available that fit the 250 Avon Super Venom Gammagirl Sat Aug 26 14 30 11 2000 The Avon Super Venom is still available in 130 90 and 100 90 for the 16 tire These tires st
142. im a bit of hose to fit the filter in there but it should fit snugly with about 1 or 2 cm cut from each side Be sure to attach the filter so that the arrow on it points toward the carbs if you cant find an arrow the side with the larger diameter goes toward the carbs You should check the filter every 3k miles for need of replacement Note Post 2000 models have an inline filter stock at the very end of the fuel line going to the carbs It is very small however and could still be assisted by a replicable aftermarket filter though it s certainly better than nothing alone How does weather affect jetting Here s the skinny on weather Cold air is more dense less activity w the molecules thus they re closer together Hot air is less dense More activity between molecules Moist air is lese dense more H20 molecules between the O2 molecules Dry air is more dense more O2 per volume of air So dry cool air is more dense moist warm air is less dense Your carburettors mix a certain amount of fuel with a certain volume of air There is an ideal ratio of fuel to air called the stoichiometric ratio which is about 14 7 1 At this ratio theoretically all of the fuel will be burned using all of the oxygen in the air In reality your bike my bike the fuel to air ratio varies from 14 7 1 quite a bit More air less gas lean more gas less air rich Your job when jetting your bike is to get as close to this ideal 14 7 1 ratio as
143. in Remove your fuel tank On the top side of each intake in front of the carbs is a vacuum nozzle Remove the black hose from each plug the hoses for the duration of the job and place one end of the clear tube on each fitting Let the clear tube hang down so the oil gathers at the bottom of the loop Start up your engine for a moment and if your carbs are in sync the oil will not flow one way more than the other If there s more vacuum from one carb or the other the oil will flow that direction Turn the linkage adjustment screw you ll need either a very long screwdriver ora stubby one in between your carbs so the vacuum is equal and you are all set It may hetp to periodically turn qi the engine for a few moments so the ot con SS at the bottom How does a choke work Chris 2 Tue Feb 29 19 20 51 2000 The choke and throttle are different The choke reduces air flow and increases fuel delivery richening the mixture the throttle adds fuel and air If you have a flooded engine the worst thing to do is pull the choke The full throttle trick works by increasing airflow to lean the mixture enough to get combustion If you take the choke off too soon on a cold engine and try to substitute you ll notice that it is virtually useless the mixture is too lean What is a fairing Zaq Tue Mar 21 11 32 11 2000 The fairing is the plastic usually covering on the motorcycle There are a lot of different kinds but the Ninja 250 is f
144. in my 325i and the 7 year old battery in Ede s 94 EX250 73 Modifications Performance I want to upgrade my exhaust What models are available Muzzy How much difference does the Muzzy exhaust system make Larry Wed Oct 27 22 48 33 1999 have just finished installing my second Muzzy system The entire system weighs just 5 1 2 Ibs on my bathroom scale The stock mufflers alone weighed 13 1 2 Ibs didn t weigh the headpipes and centerstand but it s a few pounds more off the bike as well The stainless steel head pipe looks great and fits perfectly can give installation tips if you need them Less weight more power faster better handling bike The Muzzy is loud but it has a deep tone don t think it is obnoxious A good helmet keeps most of the noise out didn t want the noise either but after considering all the available exhaust options Muzzy is the one will probably be getting a third one for my wife s bike when I can afford it Oil filter and drain plug access is fine Do have to remove the centerstand to install a Muzzy exhaust Jeb Fri Nov 16 19 28 49 2001 too wanted to keep my centerstand when put on my Muzzy system Centerstands are very useful and do miss mine indeed now There are a few problems with this however First the spring that holds the stand in place when retracted rubs the Muzzy s larger head pipe Second there is no stop for the stand anymore when retracted since the lef
145. ing too low can be harmful That said there s still no point in using an octane higher than what the factory says unless the engine s knocking With an older engine sometimes you get knocking unless you go with a higher octane You re not going to get a performance gain with a higher octane fuel If anything you ll get a performance decrease since the higher octane gas may not fully combust 37 What are those tubes hanging down from the bike for Jeb Sat Sep 2 22 14 41 2000 There are a variety of tubes that are bound together at the bottom of the bike These can include fuel tank overflow coolant system overflow carb drainage and battery vent These hoses are usually a little longer than necessary when you first get the bike you can trim them a few inches If you like but be sure to leave enough slack above the lower routing bracket and a few centimeters of travel beneath Should I use the side prop or centerstand when I park Jeb Tue Nov 13 20 07 33 2001 Use the side prop for everyday parking and the centerstand for storage and maintenance The side prop creates a larger tripod than the centerstand does and is more stable for parking on the street The centerstand creates a smaller parked footprint and takes the rear wheel off the ground this is the better position to have when doing work on the bike and when parking it at home Some people do use the centerstand exclusively though Why does my gas tank sometimes whine
146. ion That s why it s easy to lock up the back So when you are learning braking focus on using the front until just before skidding the front Do this in a warm empty parking lot free of gravel or sand Practice stopping from 30 or 40 MPH until you can stop as quickly as possible Two front discs on a 250 Is overkill can lift my back wheel in a panic stop even with a rubber brake line and a warped disc Two discs would leave you wearing your bike as a hat Maximum braking Patrik Tue Feb 29 00 42 20 2000 Remember that when maximum braking all braking power comes from the front wheel unless the surface is slippery this is the case because all weight is on the front wheel If you still have weight 29 on the rear you re not stopping as fast as you could You have to be very careful with the rear brake when doing maximum braking You are normally taught to use 75 25 or 80 20 or something as the distribution of brake power claim that on our bikes when panic stopping that should be 99 1 I m not advocating doing stoppies that s poor control but close My advice to you go to an empty parking lot and practise stopping from 25 35 45 mph carefully It s an essential survival skill to have If you want to check how you are doing a deceleration of 1g is a canonical number for good tires believe This means that your stopping distance should be 7m 25mph 13m 35mph and 21m 45mph Americans multiply by 3 to get
147. ir of raggedy old jeans not only did it fit it felt natural and comfortable astride my newly found mount Did mention it fit like a glove The wife tried to talk me out of it but convinced her I d be saving even more than if bought the cruiser It s liquid cooled it ll last longer honey it ll be less expensive to maintain The rest as they say is history picked it up November 19th and have over 1 500 miles on it No don t live in RI anymore home is now GA so get to ride much more often Now it looks like the Ninja 600 is in the plans for a fall purchase the wife wants the 250 it s a perfect fit for her at 5 1 That s my story and I m sticking to it As a second motorcycle Gazoo Thu Jan 20 19 40 04 2000 Over the summer bought my first motorcycle a Harley Davidson XL883C Sportster love that bike left the stock exhaust on it dont want to tick off the neighbors and have been riding it every weekend since The only problem with it is that don t have a garage so keep it in the basement overnight Getting it out in the morning to go to work meant riding it on the lawn fishtailing a muddy swath through grass wet with the morning dew This wasn t working out started looking at small displacement bikes something could push to the driveway and ride to work My friends tried to talk me out of it a 250 would be a deathtrap Eventually settled on the Ninja 250 mostly because of what read on the board Cheaper than o
148. is very small amount of oil at a time until oil is halfway up oe the level check window Replace the filler cap Start up the bike for a few minutes then shut off the engine and f wait a few more minutes before checking the window again Put another few ounces of oil in Repeat until oil level is consistently in the center of the view window Centerline in the window while the bike is on centerstand is the same as full with both wheels on the ground Do not overfill you could blow a gasket How often should I change the oil What kind should I use eon Wed Mar 15 18 09 35 2000 The book calls for 10W40 to 20w50 The consensus here is not to put synthetic in the bike until the break in period is finished have also heard that you shouldn t switch an old high mileage bike to synthetic as some of the crud may be plugging leaks Personally I believe that synthetic oil may increase the life of the motor by up to 50 but the extra cost of using synthetic oil exceeds the cost of replacing the motor use synthetic automotive Mobil 1 15W50 or 10W30 because don t like changing motors change both oil and filter every 3000 miles unless I m on a trip then wait till get home 39 Are there preferred brands of oil for motorcycle use Daryl Thu Nov 9 16 58 20 2000 Oils 5 00 or less that rate above average at a discount price Belray EXP Blend M C 4 99 Motul 3100 Blend M C 5 00 Golden Spectro Blend M C 4 95 Mobil 1 Tri Syn
149. ith allen head bolts which are much easier to remove With the bar end weights off take a razor and cut off the old grips from the bar up that is do not cut down into the grip work the edge of the razor between the bar under the grip and cut in an upward motion to avoid scratching the bars Then take your new grips and apply a little soapy water to the inside of the grip and to the bar itself you can also use hairspray according to Leon The soapy water or hair spray will make it easy to slide the new grips on then after a few hours will dry to leave a good seal that will keep those grips stuck on there Note the left and right grips do not have the same inner diameter so don t frustrate yourself trying to get the left hand grip onto the throttle it won t fit I d like to get some new pegs Gabe846 Tue Sep 5 01 15 29 2000 I ve got Lockhart Phillips Aluminum Racing Footpegs on my 87 they didn t fit right until bent the hell out of my footpeg brackets but they fit perfectly on the 88 2000 They gave me a noticeable amount of extra ground clearance although don t grip them as well as the stock ones I want to mount up bigger wheels Paul 311 Thu Sep 28 20 26 46 2000 mounted up a set of EX500 wheels on my race bike did it so could use a 110 front tire up front and another 120 front tire in the back EX500 wheels are 3 wide in the front and 3 5 wide in the rear These are exactly the right widths
150. ize for the 2 5 inch wide rear rim so the contact patch may be better depending on the model while a quicker steering response is effected The bead to tread height of a 120 80 tire and a 100 90 usual front stock replacement is almost identical which makes it a great rear front size combo The 120 80 tire also just looks better on the rim than a huge 130 90 in my opinion Why some people think a bigger rear tire makes the bike look bigger don t understand a bigger tire should technically make the bike itself appear smaller by comparison Downsides to using the 120 80 include a loss in final gearing 3 less than a 130 80 6 less than a 130 90 30 lower tread depth assuming a front tire mounted on the rear there are only a few manufacturers of 120 width tires made specifically for the rear wheel anymore and a loss in ride height about 1 2 A 120 width tire is a good choice for around town riding where the quicker performance can make a difference For sport touring a 130 width tire will improve high speed straight line stability How do raise the front fender to fit a 110 width tire lim Race Mon Feb 25 17 58 22 2002 1 Remove the front wheel and fender 2 Using a drill bit slightly larger than the hole in the four pop rivets drill them out from the outside of the fender 3 Remove and discard the internal steel bracket 4 Geta drill bit the same size as the bolts used to mount the fender to the fork legs 5 Caref
151. kes later my Honda SilverWing stopped being reliable wanted to get a bike that was reliable enough to ride to work narrow enough to split lanes in Washington DC traffic common enough to find parts bikes and cheap enough to replace when it wore out The Ninja 250 was the best answer Somewhere along the line took the MSF advanced course and eventually became an instructor j ust like to ride The 250 gives the best bang for the buck so far my next 250 will be running this summer unless the current 250 ZX6 or moped need more work No need for excessive speed expense Sportbiker Mon Aug 28 07 22 31 2000 bought a 250 because like to ride and like to live am happily married and have 2 young kids rode a Kawasaki for 7 years as a kid but that s been 18 years ago My Kawasaki experience then was pure joy never had a single problem with that machine after totally abusing it for 7 great years When I sold it got back half of what I d paid for it To me that s a great deal both from a money perspective and from a fun perspective Let me mention something to the macho 600cc crowd In economics there is something called diminishing marginal return It basically means that after a certain point you start getting less and less results i e riding satisfaction in this case for your money paid full sticker 3 299 for my 250 and was glad to do it the dealer only makes about 200 on this machine anyways at full stick
152. l I be able to pass reic EA 23 What benefit will I cet from 10 oie tivieel eee ee 24 But aren t those courses just for total newbies 0 ccseeeeeeececececeeeeeeeeeeeeeaneeees 24 What are some good riding techniques ccc ceeeesecccececeseesseseeeeeeceaeeeeeeceeeeeseaseegees 24 BAST OUT ONS errs cet tress Do onestineta and E tear eenae ee aeons 24 AE OA leanne erer n stead wasnt bid p sl cantecce sealed dastitaexaan E 25 Accelerating Chansine Gears aissis leae annoa a aiaa 28 Braki sainn an a a a nee Tae 29 nthe Rain Base DITEN ES ariaa a a 31 What s the meaning of some of this bike vocabulary I m hearing eeeeeeees 31 ARE CIMIIG ANI AS OM vrscas actrees ah ites wa a a a tee boendancas ete 31 DIRS le a orc ti tacereet at st cata ge tna enone tatepa ieee anion ean este eee eanete 34 I want to get a bike but my parents won t let ME 0 00 0 eee cccccecececeeseeeeeeeeeeeeaaeeeees 35 I just got a Ninja 250 amp I have some other questions about It cccccccccccccceeeeeeeeeeseseeeeees 35 Do I really have to follow this break in period ec ceecceecccececeeeeseeececeeeeseeeeeeeeeeeeaas 35 How long do I have to wait before switching to synthetic oil ec ccccsseeeeeeeeeeeeeees 36 What is the correct way to apply choke at startup ccccccccccccccesssseseecececeeeeeseeeeeeeeeeeaaas 36 My bike jolts forward when I put it in gear after first starting is this normal 36
153. l working from the left side locate the 17mm bolt at the top of the shock and remove it There is no loose nut on the other side to worry about so just take the bolt out and watch the shock fall to the ground 7 If you are installing a new shock with an external reservoir this is a good time to find a place for it If you have a Works shock and followed J eb s advice when you ordered it reservoir hose at 8 5 and the fitting at 8 30 o clock it attaches to the rear frame tube and tucks neatly behind the coolant tank 8 Slide the new shock into the top bracket and install the 17mm bolt torque spec 9 Line up the shock s bottom shackle with its matching hole by using your prybar to lift the rear tire some judicious tapping The bolt should slide right in This is not a job for a hammer folks Put the nut on and tighten it up Righty tighty lefty loosey eh 10 If you have an external reservoir secure it Use a zip tie to secure the reservoir hose to the frame You re done with your shock 11 Remount coolant tank This is a good time to fill it if needed 12 Replace side cover and seat Shouldn t take more than 30 minutes How do I adjust the rear preload Wolcott Sat Mar 18 13 58 52 2000 The stock shock is not adjustable for preload Assuming you have an EX500 SV650 or some other better shock put the shock on the bike then measure sag To do this with the bike up on the centerstand first measure distance from
154. ld have been even easier imagine So if you ever have trouble getting your slides back in try putting them on ice for a bit My bike is running fine now 32 How do I clean the air filter s Daryl Thu Jan 11 19 09 11 2001 use a little bit of Tide powder detergent and water and mix it up in a pan Let the filter sit in it for 10 to 15 minutes and then run the filter up and down in the mixture a few times Use a water hose to rinse the filter thoroughly from the inside out use a hairdryer to dry the filter then use K amp N Spray oil to lightly and evenly oil it I ve used this method on two filters with over 130 000 miles on them with good results clean filters about every 15 20 000 miles Tide s good for your cotton shirts and ok for your cotton filters How do install a fuel filter Jeb Wed Aug 30 22 12 55 2000 Go to any auto parts store and get a Purolator filter model F 10024 it s a brass filter that is small enough to fit between the tank and carbs and costs about 3 There is also another similar Purolator filter that is transparent and accepts replicable elements but do not know the model number Dennis Kirk sells some smaller see through filters for 2 each part number 18 515 a local small engine shop might also carry these Turn the fuel petcock to off then pull the tank side of the fuel line and empty the hose Reattach it and cut the hose about halfway between the carbs and tank You will have to tr
155. le formula Spending a couple days with other riders of a similar thread is much more about learning things from the others and learning things about yourself Leon and Andrew are the kings of long distance riding J eb is the technically minded computer guy who stops at nothing trying to better his bike and his riding Brian is the former 250 guy on the F3 who is the perfect example of respect for a bike that deserves it I m not sure what am maybe just the guy who sits around thinking up countless ways to re tune his carburettors None of us are about racing or worrying how long it takes the slower folks to go through the Gap or any other road we ride for that matter As fast as think am I m still only 25 to 30 as fast as the actual fast guys Last time we were there we literally crawled through the Gap because it was raining It was still a blast The next day we made the run again and was turning the wick up a bit yet Jeb who had only seen the road once I ve been through maybe 10 15 times lagged behind just a bit No one cared and we all met up at the other end No one will care what your skill level is If you want to go go The only requirement is that you be careful as that s what we ll also be doing For more info about the Gap itself check out www dealsgap com and www tailofthedragon com 113
156. le price They sell quickly and you can get almost all of your investment money back How long will a Ninja 250 engine last Leon Tue Jan 23 07 24 04 2001 The Ninja 250 motor is a consumable item like the brake pads chain sprockets tires and steering head bearings Every 30K to 60K miles you need to put a new motor in it just unbolt the old one and put a good used one back in At the Philadelphia motorcycle show asked Kawasaki about their 4 year unlimited mileage warranty was told that rings are not covered by the warranty but main bearings are and he wasn t sure about valves Shouldn t I consider a bigger bike Won t I want one later anyway Barry Thu Nov 11 16 19 01 1999 Frankly I m a bit sick of this you ll out grow the bike in a few months stuff where are people taught this If this were true everyone would be out to sell you a 250 knowing that you d be back in a few months to buy a bigger bike which means the dealer would get another sale more profit and a barely used bike as a trade in It doesn t make sense What does make sense is that as a beginning rider you need to be very careful that you don t get in over your head saying you like speed suggests to me that could easily happen to you The 250 is a great bike to start with and to keep There are more than a few on the board who have bigger bikes but still pick the 250 because its so easy to handle and that much more fun than their bigger bikes My own man
157. lision is not to be there when it happens In the Rain Basic Differences SteveS Fri Aug 4 10 27 59 2000 Learning to ride in the rain is just like learning to ride It just takes a little time to get accustomed to it believe a lot of the traction lost in the rain is actually psychological Commuters who get stuck in the rain regularly are usually quite comfortable in the rain Things to definitely watch out for e greatly increased stopping distance do not want to risk a lockup obviously road oils rising to surface when rain first starts puddles in the slow lanes near the gutters reduced visibility watchout for the cages hypothermia cold weather long trips Replace tires timely should be done regardless of rain Pick a rainy Saturday and go to an empty parking lot practice turning leaning very slow rear wheel skids What s the meaning of some of this bike vocabulary I m hearing Technical Jargon What are clip ons Gabe846 Sat Nov 25 00 32 50 2000 Clipons are handlebars that clamp individually to each fork tube rather than a single handlebar held by clamps Racers and sport bikers prefer them because they are stronger than tube handlebars are easier to adjust for position and place you lower and closer to the front wheel putting more weight over the front for better road feel and lower wind resistance Also since you can just replace one side clip ons are cheaper if you crash a lot ah
158. little over 16 500 now so it looks like this is something that needs to be done pretty regularly Yoshimura Daryl Fri Sep 22 09 11 54 2000 have a Yosh pipe it s a complete 2 into 1 system It sounds about the same as a Muzzy With The Muzzy you have to eliminate the centerstand but you can get to the oil filter on the Yosh you can keep the centerstand but you have to remove the pipe to change to oil filter Part GP270SSC for the 88 01 model year paid 319 dollars Cobra Chris Hughes Sat Jan 20 01 12 34 2001 There are 2 kinds or slip ons available Cobra F1 s and Cobra F1R s have owned both and recommend the F1 s since a they look nicer and b they sound better The F1R s are way too loud and obnoxious remember this is coming from an 18 year old male here got a noise violation ticket for them The Fl s have a lot nicer tone and of course they are still louder than stock believe Dennis Kirk sells the F1 s for around 160 and the F1R s for around 210 Do I have to rejet when I put in a new exhaust system Duke Mon Jul 3 13 27 42 2000 Just after got my bike which had a Muzzy installed but no jet kit ran it at 10K for about 45 minutes one time which did it in before realized was hurting it wound up with one of the exhaust valves about 15 melted away and the bike would no longer run under about 4 000RPM which made starting a little difficult Before that happened had to run i
159. little spring loaded aluminum parts with a little rubber nub at the end There is a float attached to this valve that pushes it up and closes it when the float bowl has enough fuel These little tiny parts cost about 25 each so your best bet is to remove them clean them and re install them if you think they are the source of the problem Another problem Ninja carbs tend to have is that the rubber O ring that seals up the float bowl will get dry and shrink and suddenly you will find that it looks like gas Is raining down from your carbs onto your starter The third fuel problem Ninja owners are likely to have is when the vacuum operated petcock fails The vacuum petcock keeps fuel from flowing out of the tank unless the bike is drawing a vacuum This keeps the bike from flooding itself when parked The needle valves should also keep this from happening but dont always do their job How do I synchronize the carburettors Duke Thu Jan 13 12 53 14 2000 Carb Sync is matching the butterfly valves in the two carburettors so they both open the same amount Your bike will not run to it s optimum level if one cylinder is running harder than the other The easiest way to understand how the adjustment works is to take your carbs off and look at the linkage There s a screw adjustment in between the two carbs that adjusts one butterfly in relation to the other Carb sync is adjusted by measuring vacuum through each carburettor and setting the butterflies
160. lp to prevent burning an exhaust valve It will idle smoother because there is less overlap that allows exhaust gases to go into the intake and lean out the mixture for the next cycle This is why an engine with cams that put peak torque at 9000 won t idle smooth at 500 rpm The exhaust system used also plays into this because it determines the amount of time the exhaust valve can be open before the gases start flowing backwards If you change the exhaust it changes the rom at which gases will reverse and let exhaust gases back into the cylinder AR anti reversion exhaust systems are supposed to give the broadest range of power because the can prevent reverse flow at a lower rpm Anyway tighter clearances will increase top end power and the chance of burning valves reduce low end power and adversely affect idling Looser clearances will make it idle better increase low to mid power and help to prevent burnt valves at the cost of top end power Of course if you go too loose then you will have a lot of valve train noise You can always try both extremes and see which works best for the kind of riding you do and the exhaust system you have What happens if the clearances are too tight loose Lou Sat Mar 25 02 31 12 2000 Generally running them too tight will increase top end power for a while until the valves overheat Then the valve and seat will erode allow the valve to start to tulip which will close the clearance even more
161. ly Screw a machine screw into each cap and use pliers to pull the screw and cap out together Once the screws are exposed turn them in gently not too tight then back out 2 turns each Put the carbs back on the bike go for a ride Come home on with a warm engine park and leave it idling Put on a jersey glove or something to protect your hand from the heat Use a small screwdriver to turn in each screw until the cylinder for the screw being adjusted starts to miss then turn it back out 1 4 to 1 2 turn Same deal for a K amp N d bike only the screws will be opened a little more 1 5 to 2 turns out should be plenty for a stock machine mine are set at 2 turns out now and have the full Muzzy K amp N package The factory setting is a little over 2 turns out think How does weather affect jetting Duke Sun Jul 14 18 52 15 2002 Here s the skinny on weather Cold air is more dense less activity w the molecules thus they re closer together Hot air is less dense More activity between molecules Moist air is lese dense more H20 molecules between the O2 molecules Dry air is more dense more O2 per volume of air So dry cool air is more dense moist warm air is less dense Your carburettors mix a certain amount of fuel with a certain volume of air There is an ideal ratio of fuel to air called the stoichiometric ratio which is about 14 7 1 At this ratio theoretically all of the fuel will be burned using all of the o
162. mely fun At this point was using some of the gears not a lot at Sears on a 250 apparently and was feeling quite comfortable felt like was doing really well on turns except for 6 and 11 Ale ROAN lt gt PERMIT PARKING VEHICLE GATE ENTRANCE PEDESTRIAN GATE ENTRANCE TRACK TURN NUMBER FIRSTAID CONCESSION RESTROOM E am i WHEELCHAIR ACCESSABLE VIEWING GRANDSTAND SEATING FOOT TRAFIC ONLY __ Fence permanent ranee ANEO y B Pedestrian Crossing Only CONSTRUCTION amp amp DEVELOPMENT a SECURITY Bs f when had my first hard bit touchdown in 7 majorly scraped my right peg and after having a short yet loud conversation with myself inside my helmet managed to get my head back together and rip through 10 nearly WFO in sixth gear just to prove to myself that it was a fluke This lead me to the conclusion that one doesn t really need to make time up on the track in a personal proof as riding so near to the grass and dirt at 100 mph or more Is a very humbling and non gratifying experience think we ran 9 laps or so in this session and my buddy had my watch and was timing me just for my curiosity ran a 2 26 at some point in this session which made me feel pretty damn good Near the end of this session also had experienced a foot cramp which I m blaming on a combination of being out of shape and cramming a 6 2 rider onto a bike that doesn t really fit This got
163. mo no air Also check Is your choke cable mechanism working properly on your carbs The choke may be stuck on Are both spark plugs getting good fire Are your valves adj usted properly Are your carbs synced Have your carbs been cleaned in the past several years My engine is backfiring Jeb Thu May 31 19 51 42 2001 If the engine is just popping a little bit as you decelerate then you re getting preignition This is caused by a lean mixture condition Check carbs for vacuum leaks or richen raise the needles or idle mixture turn out screws If the bike is seriously backfiring then you might still have a lean condition or maybe even a rich condition check your choke This is because a lean mixture can make the engine miss then the unburnt gasses are ignited in the exhaust pipe on the next cycle a rich mixture can have the same effect since unburned fuel will also be present Check pilot circuits in the carbs change the spark plugs make sure to gap them properly check for exhaust leaks If all else fails try a higher octane fuel 69 My bike will run for a while but keeps losing power and dying when ride it Leon Fri Sep 29 10 48 31 2000 This is tight valves It dies at low RPMs but will continue to run if the throttle is opened Take the bike in and have the valves adjusted or do it yourself before you do real damage to the motor I think my tire is losing air Nosferatu_d Thu Jan 13 07 47 4
164. n The Street Real World Performance AR Fri Feb 23 13 25 06 2001 thought you might appreciate two of the recent experiences I ve had gently tooling about San Diego county on my itty bitty 250 The first was an extensive full day ride on highway 1 the coast route smack on the beach in the company of a 2001 Harley Sportster 1200S This Is Harley s not Buell s fastest meanest light 550 Ibs sportbike If he got the drop on me catching me with my revs down he could torque past me but couldn t pull ahead any farther than my front wheel abreast his rear wheel If we took off from a dead stop would jump a half length out and then we stayed at the same point This was on twisty coastal highway and our speeds were restricted we never got above 85 indicated My buddy was miffed The second was a brief three stoplight affair on Frairs Rd with a Honda ST1100 When we stopped at the third light the Honda rider flipped back his face shield and inquired if was riding a new 500 When told him it was a 250 he was stunned His exact words A 250 That bike is awesome Riding in Traffic Leon Tue May 1 10 01 49 2001 Some insight on what it s like to ride a 250 in traffic it s a heck of a lot of fun Very light very flickable quick economical With apologies to the late Roger Miller you can rollerskate in a buffalo herd The Ninja 250 is wonderful in either heavy city traffic or very tight twisty roads like Deal s Gap At the
165. n of tires presently manufactured for 16 wheels which will work as well as these two tires They re cheap too don t have any sort of tire sponsorship so I m not trying to sell anyone Dunlops Every single Ninja 250 that races with the AFM runs Dunlop K591 s except for a couple people I ve seen running stock tires on their very first race weekend Dunlop GT501 Paul 311 Thu Sep 28 20 31 09 2000 The K591 s are now out of major production though will still be available for a while the GT501 s are their replacement Here s a quick second hand review Fast guy Robert Kennedy tested out the new Dunlop GT501 s at the track last weekend He thought they felt as good or better than 591 s and they also seemed to wear pretty well The smallest front is a 110 90 16 which required fender modification moved it up to keep it from dragging The choices for the rear are the same as before 130 90 16 or 120 80 16 He did comment that the larger front tire made the bike steer more slowly think the increased tire size and the pinched profile probably offset each other so the contact patch is about the same Robert did his best ever lap times on these tires Sunday He had to lower the front end a little to make the bike turn in more quickly in order to compensate for the fatter tire Robert used these tires to just barely beat me my trick wheels and my trick Dunlop D207GP and GP tires Skill wins over technology again Kenda Jeb Wed Sept 5 10
166. nces and are easily damaged Also recognize that most of the retaining screws are made of brass and again are easily damaged Use no more pressure than necessary when adjusting them and do not use the screwdriver included with the bike or a cheap Wal Mart screwdriver use a hardened screwdriver with well cut blades 8 at a hardware store should get you something acceptable Where can I purchase a jet kit for my bike Dynojet Research Inc Factory Pro Tuning Can improve carb performance without buying a whole jet kit Paul 311 Sun Jan 23 22 44 30 2000 You can get about 90 of the performance of installing a jet kit by installing new main jets Main jets are available from better motorcycle shops You just bring in your old ones and tell them what size you want or even tell them you want one size larger richer or one size smaller more lean Believe it or not my CB 1 jet kit came with jets that were a size smaller than stock and the bike makes more power A lot of J apanese bikes come jetted a rich on top and will make more power if jetted more lean the needles will then need to be raised a bit to richen them as they are usually on the lean side to start with My race Ninja when bought it had been jetted with size 98 main jets stock Is 105 and it had lots of power The reason suggest buying main jets without the jet kit is that a set of main jets for a Ninja is about 8 A jet kit for a Ninja is about 70 The nice thing
167. nd The Crest is closed all winter due to avalanches that frequently remove and or bury portions of the road so if you want to ride it you must do so either before the first snow falls or after it s melted off in the late spring The Ninja did pretty well although it got a little short of breath at altitudes above six thousand feet The flickability of the bike proved just the thing for threading between the frequent remains of rockslides without upsetting the bike s balance J ust put your eyes where you want to be and the bike will go there for you Also discovered that the Ninja is pretty forgiving of braking into corners rockslides again and tends to stand up less than most sport bikes when you hit the binders The bad news is that the too soft stock suspension lets the bike really nose dive when under full braking This sudden weight transfer pretty much means that you must do 99 of your serious braking with the front wheel only because the rear locks up very easily as it unloads The stock tires that the bike came with are pretty hard which makes the problem worse Other than the soft suspension the bike seems to have no bad habits even when pushed pretty hard Getting the most out of the engine seems to mean keeping it up between 6000 RPM and redline but it does have a wide enough power band to accelerate all the way through most corners without shifting provided that you choose the correct gear before entering And the bike does l
168. nd attractive The vector design for the ZX 2R logo itself is not as streamlined as the present ZX 6R logo it is instead derived an earlier ZX 6 design which is blockier did this because the Ninja 250 is built on a 1988 platform after all and felt more rigid lines would better match the angular fairing design The kit comes with one pair of 10 ZX 2R decals available in white silver or black Also included are two 7 Kawasaki decals in white silver or black and two 5 Ninja decals in white w black shadow silver w black shadow or black w silver shadow A ZX 5R kit is also available The kit is 40 shipped which is very reasonable if you compare to the vinyl kits available from www tapeworks com for example Please email me if you are interested in ordering a set or would like more information Is a seat cowl available for the Ninja 250 Jeb Thu Sept 7 22 34 17 2003 The only seat cowl available for the EX250 at this time is made by AirTech Streamlining It looks similar to this and requires permanent seat mounting and alteration for the tail lights am presently working on a seat model which will allow retaining the stock seat and tail configuration the only part that will require removal will be the rear grab bar It is still in the early modelling phases but will hopefully be ready sometime in the Spring of 2004 It should look very similar to the cowl on the FAQ home page Newbies want to
169. nd Performance Statistics vscicissceiedivessteds eeidedicienadacieecies Mec 12 Baal abla eer ent See meneame Concer ter acr ketene ene Mon reer ene Amen EE tenet TE 14 Wiat Colos ATE Asy Ala le 7 sesh czccte vino savannas a deste tunaseae desea 14 W ene air Tr Rnd Or O Serc oscars wa cesta ace aaeceslea as E 15 I want to know more about motorcycling in general cc eeeeecccccecesseeeeeeceeeceaeeeeesceeeeeeeaneeees 15 I want to get a bike but I don t know the process ssssseensesessssssssseseererereesssssssssseseees 15 What riding sear should Nave Kesini ae tein aeate ERTO E 15 PC LINC eaaa E ee iec castorate Nasnantens ne teak ccd lceuan nee ee E 15 should wear a helmet Tio Nenen tines vances aed oat nvadiae icon leact eel nasteltents 15 How much should I plan on spending cc eceecceecccccceeeeseeeeceeeeeaaeeeeseeeeeeeeaaenees 16 should seta ful ace Kennet isi tciccatasisteie Avieeeeaia a a aden 16 What ate some sood MODES vcssdsenduccdenccucadncesunreuaty dasviedus ate Sduasdordadechactecassdedseedmaweess 16 How do I keep my visor from fogsing UP 0 seseeccccceceeeeseeeecececeeeeeseeeeeeeeseeaeeees 16 MC NC st See EE E active detail cities VAE A tastes bac E E ate eerste enchant 17 Leather VSee o QUA yaa sc a te leatiwiaeaeeaeetoemes 17 PPADS cute ogee wisest corendaniciee uses senasanesers anche sd enneetausleat asses fauna eoruene naan aieatiectoet nate 17 Joe Rocket Ballistic Paints eunea a T E A T ante 17
170. nd connect it to the black pin this will ground the relay without having to cut the ground wire for the bulb e The white pin is not used It works like this normally current will flow through the blue and yellow terminals to the light from the constant wire keeping it lit When you activate the signal switch the voltage coming from the battery with induce an electromagnetic current in the coil between the red and black pins causing the relay to remove voltage from the constant wire and apply to the white pin to which nothing is attached This will make the bulb up front flash off on while the bulb in the rear flashes on off Note the relays will not draw nearly as much current as the stock lamps which will upset the thermal flasher that makes them blink You ll to remove the thermal flasher and replace it with an electric flasher from any auto parts store which is load independent I want tail lights with more brightness contrast Jeb Sun Nov 18 08 34 19 2001 These DOT approved bulbs are interchangeable Trade No Filament Volts Watts Amps CP Life 2057 Low 14 0 6 86 0 49 2 5000 High 12 8 26 88 2 10 32 1200 1034 Low 14 0 7 14 0 51 2 5000 High 12 8 23 04 1 80 26 1200 1157 Low 14 0 8 26 0 59 3 5000 High 12 8 26 88 2 10 32 1200 2397 Low 14 0 6 72 0 48 2 5000 High 12 8 28 54 2 23 40 400 2357 Low 14 0 8 26 0 59 3 5000 High 12 8 28 54 2 23 40 400 CP Candle Power For example I use a 2357 in the center light and 2397 s on the
171. nd if you take the MSF Motorcycle Safety Foundation course you can usually get a discount Should get any extended coverage Patrik Tue Feb 15 00 27 06 2000 hit an ole making a left turn when he was behind a van and in a right hander Don t ask me what he was thinking if he was Probably wasn t he hadn t been thinking for the preceding 4 days when he got his car but no insurance Get uninsured motorist coverage would gladly have paid the extra hundred bucks a year that it would have cost to escape my current situation I m out of pocket about 2k my health insurance has claim of another 2k on me in case ever get any damages from the driver and have no bike My chances of getting damages seem slim as most lawyers won t touch a lawsuit against an uninsured poor economically speaking loser that already has earlier court judgements that he s paying off and even if was to win such a lawsuit the wisdom seems to be that collecting Is unlikely should reemphasize this UM is worth getting The current estimate of the uninsured vehicle rate in California is something like 34 That s 1 OUT OF 3 It makes me pissed off that need to get insurance for something that is someone else s responsibility but that s the situation What insurance companies should check out Geico Progressive 22 Should I take an MSF course What is an MSF course Leon Fri Nov 12 13 15 04 1999 The Motorcycle Safety Fou
172. ndation course teaches the basics of riding a motorcycle then extends those basics to interacting with other road users and finally dealing with unusual things This course is designed for those who have never ridden but does expect some familiarity with driving Some beginners find even the beginner course intimidating but that s usually because the class sizes and time don t allow for any falling behind If you have already ridden on the street and particularly if you already have your motorcycle endorsement you might wish to skip the basic MSF course and go directly to the Experienced Rider Course The beginner course is 16 20 hours long the experienced rider course is about 8 hours Most of the things covered in the experienced rider course are a review of what s in the beginner course Many of the exercises are slightly different so those who have had the earlier course will still find it interesting and challenging Who should take the beginner course e Anyone who has not ridden a motorcycle but can ride a bicycle e Anyone with less than a year or so of riding experience and is interested in learning more about riding e Anyone who needs a motorcycle endorsement on their driver s license Many but not all states will take the course as proof of the riding part of the licensing process The instructors will probably be familiar with the licensing process for your state Who should not take the beginner course e Anyone who c
173. ng it back to life Jake Tue Jan 2 13 39 43 2001 1 Charge the battery after disconnecting and removing it You may have a current leak on the bike somewhere 2 Check that the leads are on correctly I know you didnt hook it up wrong but you d be surprised 3 If the charger has a voltage switch set it to 12V 4 Try a different charger if you have access to one 5 If the battery has removable fill caps add distilled water to the fill line 6 If the battery has removable fill caps and adding water does not improve it s ability to charge and hold a charge buy an electrolyte checker Follow the instructions This device checks the acid content and hence the ability to take a charge of the water in the individual cells 7 If the battery does not have removable fill caps you re done Get a new one In general check the voltage after you unplug and disconnect the charger Shouldn t make a difference but you want to eliminate all but one variables in testing My engine is running poorly My engine lacks power under throttle load Duke Mon Jan 24 22 20 58 2000 Make sure there s nothing covering the openings to the airbox under the seat One time had some maps in a zip lock bag under the seat It was cutting out at full throttle and couldn t figure out why well guess what that zip lock bag was over the two holes in the airbox and every time opened it up the vacuum was sucking the bag down on the airbox and wha
174. ng position is more conducive to countersteering and gives a sense of added control The grips and controls are lower and more forward putting more weight over the front wheel Second lowering the chassis to enable installation lowers the center of gravity slightly and also reduces the rake trail and wheelbase a bit The stock ex250 has a higher rake angle than many sportbikes and so it is easier to ride though not as quick in turning as it could be it is quick to steer because it is so light So by reducing the rake and trail by raising the fork tubes a few centimeters you can find a spot in the steering geometry which is both quicker steering and still quite stable What models will fit the EX250 Dweedlebug Sat Sep 1 01 04 32 2001 As far as know there are five choices 1 2 the Woodcraft lowered risers or clip ons www woodcraft cfm com 3 the Vortex clip ons www vortexracing com 4 the Pro Flo clip ons www pro flo com 5 the Pro Tek clip ons www protekk com Or get a machinist to custom build a pair basically just a 36mm clamp with a 7 8 bar bolted welded to it How do put them on the bike Wolcott Sun Feb 27 06 22 37 2000 Step one Most critical cover the tank and front fender with thick soft cloth so they won t get damaged or scratched Slip a thin tool or screwdriver between the bar and the grip and loosen the glue then work them off the bar If they get damaged coming off buy a set of aftermark
175. ng the tires in is that the front end of the bike no longer feels like its just there You can actually get a feeling for what s going on between the front suspension and the ground Turns at speed became enjoyable instead of feeling like work didn t have to wonder if I m going to fast for the curve anymore because the tires are actually telling me what s going on down there put lots of miles on them in various different conditions Rain slow speed commuting fast speed commuting twisty mountain roads and everything in between They seem to be pretty decent in all conditions save snow decided to retire the Strada after 10k miles of daily use after a mishap with a nail and a plug that failed It still sits mounted on a rim fully inflated in the event of an emergency tons of tread still on it The BT45 is still going strong at 12k miles but I ll probably replace before the winter sets in Pirelli Sport Demon Brent Wed Apr 16 16 28 04 2003 Pirelli has a new tire option for the 250 ina 100 90 16 front and 130 90 16 rear It s the Sport Demon tire and seems to be marketed as a sporty touring tire It seems wedged between the MT66 which they list as a cruiser and the MT75 which they list as sport The MT75 treated me well so see no reason to why the Sport Demon would not perform well Three of the online tire dealers checked list this tire www mawonline com www discountmotorcycletire com and www denniskirk com they average
176. no authority but it sounds like a crap shoot to me and ain t no gambler If you wanna get really flashy look at what ProTek sells Bright dip anodized lightened rear sprockets have no info on anyone that has ever used these but they are the looks if that is what you are after Check out the bar ends they offer too nice stuff eh Their billet ones make any of the other aftermarket bar ends look like crap in my opinion How do adjust the valves Why do the valves need to be adjusted VD Sun Jun 15 02 22 58 2003 The valve clearances determine to a degree when the valves open and close how long they stay open and how far they open Your engine breathes through the valves as these are the openings that allow the air fuel mixture from the carburettor intake valve into the combustion chamber and for the piston to expel what s left after that combustion takes place exhaust valves out through the exhaust pipe to make room for the next fresh charge of air fuel mixture Technical crap aside the most important reason on the 250 is that the parts inside the combustion chamber valve heads and or valve seats on the cylinder head wear at a faster rate than the parts under the valve cover valve nibs rocker arm pads cam lobes tappet screws Wow that sounds like more technical crap Translation the valve clearances get tighter on the 250 as you rack up the miles and if they get so tight that there s zero clearance they ll
177. nocked over by a backing up No damage except a scuff on the handlebar ends and a dirt mark on the bag e nice sturdy clips and straps to hitch to the bike e sleek shape and zoom y looking position on bike e pricey mine were 110 from the Aerostich RiderWearhouse e if you are too exuberant with the zippers all your stuff might fall out The bags can open really wide which is a pro really e you shouldn t carry really heavy stuff in them according to the manual e itis hard to figure out where to hook the straps this could be a pro since it gives you some different options depending on your bike set up e if you don t hook them onto your bike evenly they will look a little goofy and lop sided e depending on how you hook them on it can be a challenge to get them off quickly just leave mine on Lighting I want to know more about headlight modulators VFR Pilot Fri Aug 3 01 01 24 2001 got a Kisan Pathblazer headlight modulator installed on my bike just over two weeks ago and now have circa 600 miles worth of road time to evaluate For those you are feeling confused A headlight modulator causes your high beams to modulate from full bright to about 20 of power at a rate of four times a second Yes it s legal Firstly Kisan and the Feds are right the modulator will get you noticed But the point with this thing is to use it when you need to not just leave it on all the time to annoy oncoming drivers There a
178. o repaint he Dody WO konne a A E n 99 I want to remove the paint from my wheels for a polished look eee eee ceeeeeeeees 100 lwanttorepant my Exhaust PIPES sisisicie tacacdoiaen ene e gana 100 T wantt0 remove the Tat Tenet eini e E a ou 100 DeWalt AMO W Winds CCM sss te vies ins area Saat so bene Ges eiisaen nett nim tc hauhatasde E 100 What models Colors areav allaDle aens E E 100 How do I properly attach the windscreen to avoid breakage ccccccceeesceeeeeeeeeeeees 101 I want to improve the appearance of my Jights cccceseesseecececeeeeeeeeeeceeeeeaaeeeees 101 I want to wire extra brake lights into those empty rear sockets cccccceeeeeeeeees 101 I want to replace the front flasher pods with flush mounted units ceeeee 101 Ferona l ACCOUNTS acceccnncocenasaatusedunsvatenacenacadare osu a aaea 103 Choosine the Ninja 2 Orainean a a NO ET O RA 103 Wanted a Dike TOG VOaUS cara a a oaknareeaeeet 103 WAS A SECON IMOIOECY Cle iai5 tosis oe a a li nado anaconda eee 103 Best DIKE TOr your dolli carpus Serena cndanrea seis dotune aPavka E 104 INO need forex CessiVe Speed EXPENSE a cciweieitscosiseniuintnland dbase eee a cade 104 OV Acie be Ac EO eee eR oe none te Ee ee nee ees ane ee ee gee ee Cee ee ee ee ee 104 TNS YS te E cr ct A eta NE es Ae 107 idan SUMINEROM The CICS Eense E a aa 107 TS OO Mies in 2 FoI OUI sess acute eraser nad en inte ein ah Ledad ani a a dolatiates 108 O
179. orking days cleaning and building In between are several unexpected parts orders Now that I m rebuilding for the 5th or 6th time there are less unexpected parts to be ordered but always some sort of gotcha How do I line everything up after rebuilding the top end James Sun Jul 2 17 37 14 2000 You want rotate the engine counterclockwise until the 2T mark shows in the window then go clockwise 90 degrees Remove the tensioner you probably already have it off You want the EX mark to line up with the head towards the front of the bike and IN mark to line up at the back this sounds backwards but it s straight out of the manual and it worked on my bike The cams can should only fit into the cam gears one way so they should be exactly where you want them if the gears are lined up correctly with the head You should be able to count 33pins in the timing chain between the two timing marks on the gears Once this is done you should be able to put the caps on and timing chain cover along with the tensioner do the tensioner as soon as you have the chain cams gears timed then the caps Tighten the caps in this order top bolts on the 2 and 4 caps then bottoms then tops on the 1 and three then the bottoms then torque them in that order as well torque specs are pretty tight it s like 104 in Ibs I m having trouble putting my bike on its centerstand Wes Sat Nov 10 16 09 57 2001 1 Put bike on sidestand 2 Stand to left of bike 3 P
180. osing traction VFR Pilot Sun Jun 16 02 41 29 2002 If you think your tires are slipping you are almost certainly mistaken When a motorcycle s tires actually lose traction in a corner the bike almost invariably lowsides bang right then and there Unless you re leaned way over and are dragging parts hard enough to lever the rear wheel off of the ground or unless you ve just hit a gravel patch the tires aren t likely to be slipping what you re feeling is probably just the 250 s frame and suspension flexing and or the tires walking sideways a bit across irregularities in the pavement All motorcycles do this to some extent and it s generally nothing to worry about Huge chuckholes frost heaves or nasty tar snakes being obvious exceptions While it s impossible to make one statement that can cover all the variables in these situations you are usually much better off to hold your line through a corner rather than run off of the outside While you might go down if you attempt to hold your line you will almost certainly go down if you run off of the pavement Sliding down the road from a lowside will probably damage both yourself and your bike but not as badly as would laminating yourself to a common roadside object such as a tree rock cow or Armco barrier If it s possible for you to attend a track school such as Reggie Pridmore s CLASS would strongly recommend it Getting out on a track with fresh tires will allow you to learn
181. outer lights The 2357 has a standard low filament like the 1157 and a brighter brake lamp good for a normal running lamp with a bright brake light The 2397 has a dimmer running lamp and a brighter brake lamp than the 1157 good for a bright brake light or in my case turn signals but with more contrast due to the dimmer running filament which also uses less power and produces less heat Aesthetic Modifications I want to remove the decals from my bike Larry Tue Nov 2 07 27 16 1999 The older the bike the harder it is to remove the decals On new bikes they will peel right off On older bikes a hair dryer or heat gun will help soften the sticker Most likely it will leave some glue residue WD 40 or turpentine will help remove the residue Follow with a good coat of cleaner wax 98 I want to repaint my bike I want to repaint the bodywork Scrum Fri Sep 29 17 33 13 2000 was in the market for a used bike but came into some money and was able to buy a new 2000 hated the black color of the older bikes so was practicing stripping and repainting on hard plastic buckets know it s not quite the same material as what s found on a bike but it s close From my experiences stripping the paint is the most difficult part Using a chemical stripper will eat the plastic and most special products don t do much The best way to do it is with wet dry sand paper You can find this in any automotive store like Pep Boys don
182. pin with a new one they re only 25 each check everything one more time and go ride Yes know the right way to line up the rear wheel is with a couple of straight edges But this is about chain tension wheel alignment is a separate topic How do I replace the chain Jeb Tue Mar 19 12 22 18 2002 You don t need any special chain breaking or riveting tools a dremel with cutting wheel two 2 c clamp and 2 hammers work just fine Use the dremel to carefully trim off the excess linkage from the new chain if any Take off the front sprocket cover so you can get a good look at how the new chain should be threaded on Use the dremel to cut off the old chain it will help to remove the left exhaust canister if you have one Loosen the rear axle put the bike on centerstand and kick the wheel forward after loosening the swingarm adjusters and rear brake torque arm Put the new chain over both sprockets and bring the ends together under the top run Grease and assemble the o rings and master link Hopefully you got a riveting master link and not a clip type link the clip type is fine but more likely to fail soontaneously not likely to fail just more likely Both are assembled similarly using the c clamps to compress the link and plate Using one c clamp per pin put the flat side of the c against the far pin the one that s already riveted and the cupped side of the c over the pin that you re pushing through so you don t squis
183. point and nearly running off Only by majorly 108 increasing my lean oh shit my tires are freezing did manage to make it through and continue on was really really determined NOT to have a get off my first track day My next thrill was eleven and not because found it such a tough corner regardless of how many times failed to properly late apex it but because the damn pavement looks so totally screwed up and greasy as hell Especially in an early morning light I m rambling Anyway The rest of the first session went well and had seriously shed any mental fog had at this point and was becoming much more comfortable with the bike revving it up into the early teens with gusto The session ended without incident and we headed back to the classroom The second session was very cool and became much more comfortable with the bike s handling It is a good thing that despite being tall I m also a skinny bastard so I m not upsetting the stock suspension bits as much as a heavier rider might The stock tires although slightly broken in heh by the end of the second session seemed to be relatively confidence inspiring as well A crash in 11 foreshortened the second session two actually one student bike followed another s oil slick at slow speed into the bales and pulled into the pits We took a third quick classroom If remember correctly then broke for lunch and my Mom showed up Cool Third session was extre
184. r than I d like but it s tolerable The repair kit consists of the perforated inner tube wrapped in fibreglass ordered this directly from Muzzy last fall If you could get the right fibreglass material from a muffler shop or auto parts store there is no reason you couldnt just replace this bit since the metal pieces were all in good shape To install this just drill out the rivets and remove the end cap sounds simple but there was the small matter of a broken drill bit and what seemed like a lot of blood at the time Only one end cap needs to come off and the engine side cap Is easier to get off since the mounting hardware provides something to pull on removed both caps because want to experiment with some additional baffling at the outlet end You can go to www muzzys com and order the kit It s about 25 You ll need a pop rivet tool about 10 and rivets 1 8 diameter 3 8 length to put it all back together The end caps are stainless steel and are reused poked around the web and found packing for glass pack mufflers several places for about 6 If were to do it over I d just get the packing suspect that auto stores or motorcycle shops probably stock this kind of stuff I ve no idea where the old packing goes guess it just breaks into small pieces and blows out the tail pipe bought the bike with the Muzzy so don t know how long it has been on there The bike had about 10 000 miles when I got it and it s at a
185. rbs and carb boots back on in the opposite order you removed them Poof Instant clean carbs except that it will actually take you 3 4 hours to do it right How do I get the vacuum pistons back in correctly Jeb Mon Oct 2 13 19 16 2000 After pulling and disassembling my carbs probably 10 times the diaphragms of my carbs jet needle vacuum pistons have started to become a little misshapen Not a big deal but reseating them has become more of chore each time This time thought had them seated adequately but when went for a ride that night found that the throttle input wasn t lifting the guides as much as it should have been so the needles weren t rising out of the jets enough and was running lean and sluggish pulled the carbs again today and sure enough the diaphragms were kinked and out of round under the top boots After another several attempts to get them back in properly gave up and tried to figure out what to with them wasn t about to replace them they were still in decent shape and usable plus new ones are very expensive but couldn t get them back inside the carbs Then remembered something read several months ago about getting them cold so they would shrink enough to be put in correctly So put mine in the freezer for an hour and sure enough they did shrink a little and stiffen up enough for me to get the rubber rims lined up with the groove on the carb body if I d left them in another hour it wou
186. re two situations where a modulator comes in really handy a Passing on two lane roads and b alerting oncoming traffic when you need to a Ive found that slower traffic does move over and let me past more frequently than they did pre Kisan and note four separate reactions to the Pathblazer 1 Little old ladies seem to think that I m a cop and pull over instantly anywhere 2 Drivers who normally don t look in their mirrors are alerted by the flashing and now see me Some move a few dont but it s a net gain 3 The same spaced out whackos who didn t know there was anybody else on the planet still don t notice or care that you re behind them 4 Guys in hot cars seem to take it as a challenge and try to outrun me Which gets them out of my way so that s fine b Better than the improvement in the passing situation is the new ability to grab the attention of the oncoming doofus who s about to make a left turn or pull out in front of you from a 96 side road While riding in the mountains today had this happen to me no less than three times Once a truck started pulling onto the road from the right without really looking and twice drivers started to turn left into me In all three cases they saw me and slammed to a halt as soon as I hit the modulator This is impressive have heard various opinions on modulators ranging from Great to Spawn of the Devil but now suspect that the gt anti lt crowd is largely composed o
187. ried about horribly screwing up the plastic that you just bought relax There is almost nothing you can do the plastic that a body shop can t undo and then repaint As for colors when you go to the automotive store they ll have more colors then you thought possible personally like the candy blue that is close to what some of the EX500 have Oh so nice If you re trying to match a factory color check out www color rite com After a little searching found the site that helped me a lot http www thegsresources com garage gs repaint htm It s the best article I ve found on how to do it yourself 99 I want to remove the paint from my wheels for a polished look Lentz Wed Jun 6 14 00 24 2001 To polish the rims used paint stripper in a spray can and about 2 boxes of Brillo pads put the bike on the centerstand sprayed some stripper on the rims being careful not the get it on the tires let it sit for 10 seconds then scrubbed vigorously with a brillo pad It took about 30 mins per wheel The paint on the spokes and the other rough surfaces on the wheel isn t coming off without a fight The finish is shiny and looks great I want to repaint my exhaust pipes Brent Tue Jul 17 12 37 27 2001 used high heat engine paint from Autozone Dupli Cote in Aluminum color sanded the pipe with fine sandpaper and used a dremel tool with a wire brush to clean around the welds and then painted it If you just strip
188. ring those long high speed freeway runs You can still hear sirens horns and so forth but the wind noise is pretty much gone And that constant wind noise really tires you out Try it and see Best of all these things are legal at least in California under the provisions of the law whereas store bought plugs are not Aerostich suit Paul 311 Tue Jun 6 13 10 49 2000 I m not sponsored by Aerostich but am a big believer in their gear tossed my CB 1 down an offramp at 7Omph about two weeks ago on my way to work had my Aerostich on was wearing Daytona race boots and Held gloves had a bruise on my left hand but that was it wasn t even late to work because of the crash The Stich costs about 700 and you have to wait a while to get one They are worth every dollar They have a website at www aerostich com They only sell their suits direct through rider warehouse which think is the retail side of their company If you plan on crashing at speeds over 70mph would recommend full leathers have a set of Erbo leathers which have crashed on the track about 7 times and have never needed to repair them You can t typically fit regular clothes on under leathers but Aerostich suits are made to be worn with clothing under them A few times a month wear a business suit to work under my Aerostich The Stich is also holds off hard rain for about 30 45 minutes Full leathers Brian F3 Sat Aug 5 20 49 56 2000 AGV
189. rmance Pro Honda HP Lube Kawasaki K Kare Foaming PJ 1 Chain Lube blue and Torco Power Slide Titanium All these scored 21 5 to 23 5 points in their tests for clings rolling resistances grit resistance etc How do I measure chain slack Jeb Wed Dec 5 12 16 33 2001 Cut out a piece of cardboard approximately 1 x 4 long Draw a line on it and put markers at 0 30 and 40 mm points Place the end of the cardboard piece against the bottom of the swingarm toward the front above the center of the bottom chain run Put the bike on its centerstand Gently tug the chain taut down and then up noting the entire amount of slack present Less than 25 mm is too tight more than 45 Is too loose 30 40 mm is just fine How do I adjust chain tension Leon Wed May 31 18 40 07 2000 Remove the cotter pin from the rear axle Loosen the nut on the rear axle a couple of turns Loosen the 17 mm nut that retains the brake calliper arm just a bit Loosen the two 12 mm lock nuts one on each side behind the axle The nuts are actually 8mm nuts but it takes a 12mm wrench to loosen them Back the nuts off about 1 2 in 10 15mm Tighten the chain tension bolt on the left side of the bike until the chain is almost right Look at the mark on the chain adjuster above the axle Adjust the right side so the mark on that side is the same Recheck the chain slack Adjust it again if needed Tighten the locknuts brake arm nut and axle nut replace the cotter
190. rting although it often will at least sputter There Is an allen head screw under the carb that will let fuel drain out that little nipple under the carb put a cup or some such under there to catch the gas If the gas in the tank is older than a year drain the tank and put fresh gas in Now put the petcock to prime if you have that setting and try starting again It will take some cranking of the engine for the gas to re fill the carb bowls so give it 10 tries If it doesn t start go to 5 Clean the spark plugs or put new ones in if you have them It s such a pain to get at the plugs that would definitely leave this to late in the operation and I d even go out and buy starter fluid first but still it s easier than cleaning the carbs If the bike still won t start with good Spark starter fluid or fresh gas and clean plugs then pull the carbs and clean them My battery is dead how do push start my bike Leon Wed Jun 7 13 48 36 2000 The bike won t roll very well when it s in gear the drag from the wet clutch and transmission is very noticeable 1 2 Get the bike rolling with the transmission in neutral the clutch pulled in the ignition and engine cut off switch on Stand up from the seat then simultaneously drop to the seat as you press down into first and release the clutch Dropping to the seat will give the rear tire the extra traction it needs to get the engine rolling 68 My battery is dead how can I bri
191. rts won t seat completely didn t believe them but tiz true What is the correct way to apply choke at startup Jeb Wed Oct 3 14 23 53 2001 Turn ignition key to on position leave choke off Press starter button with one finger no throttle while gradually turning up the choke After about three seconds the choke and carb priming should be adequate to start the engine Use no more choke than necessary to keep the bike idling The gradual application method is better than just turning on the choke and then trying to start it because the ninja rarely needs full choke to get going You don t want to give it too much choke because you risk flooding the engine and encouraging carbon deposits on the valves As soon as the engine is in the rhythm 60 seconds or less ride off do not idle the engine to warm it up Keep the revs low and turn off the choke after you re a few blocks from home Increase revs as the bike warms up Choke should only be needed to start a cold engine It may take some practice to get your starting technique perfected My bike jolts forward when I put it in gear after first starting is this normal Barry Sat Jul 15 21 42 55 2000 It s normal for the bike to jump forward when it has sat for a while The Ninja 250 has a wet clutch the same oil that lubes the engine also flows in around the clutch If the bike sits for a while the oil will be forced out from between the clutch plates the bike jerks when you s
192. s annoying but necessary We generally depend on ONE brake to stop us Cars have 4 and can afford to lose half of the braking power and still slow down enough to stay mostly out of trouble We re screwed if we lose any power How do I change the brake fluid Jeb Wed Mar 22 12 44 54 2000 Okay this is not hard but it can take a long time set aside an hour if you plan on doing front and rear You need to change the brake fluid every two or three years or when you want to bleed the brakes but dont know what kind of fluid is presently in use you should bleed the brakes whenever they start to feel weak or soft used 12 oz bottle of DOT4 brake fluid new 3 ft of clear 3 8 vinyl hose small toolkit cresent wrench small toolkit phillips head screw driver sealable plastic container used an empty milk chug bottle a few old rags Put the bike on centerstand attach the hose to the front bleeder valve and run the length of hose into the empty bottle Carefully open the valve with the wrench and repeatedly squeeze the brake lever until no more fluid comes out Close the valve 48 Now comes the lengthy and frustrating part new fluid has to be poured into the master cylinder reservoir and pumped back into the brake line Two things make this a pain there is no pressure in the line any more so it takes twice as long to put the fluid back in as it did to pump it out also you must constantly monitor the reservoir level and not
193. s in quick succession while going through the gears downshifting it will become a rhythmic second nature habit that occurs simultaneously to braking Once this is perfected it s possible to brake hard into a turn before the turn and downshift at the same time avoiding any rear wheel slide This works best in the lower gears where it s possible to quickly downshift through three or four gears much quicker than the bike slows down Entering a turn too fast Leon Mon Jun 4 15 15 37 2001 I ve heard of a lot of things to do when trying to recover 1 Use the rear brake to tighten up the line a little bit It feels right to me but the real racer guys say this is not the answer because if the rear wheel breaks loose the rear end will go wide and cause you to crash 2 Reduce throttle and use both brakes to slow slightly realizing that most of the traction is being used for turning It will slow you down but uses additional traction 3 Lean to the inside and continue to apply the throttle leaning in will cause the bike to straighten up giving more ground clearance so hard parts don t scrape takes lots of courage to go faster when your brain already says you re going too fast 4 Straighten up brake in a straight line to scrub off speed then release the brakes and turn in tighter Requires some room to run wider than you re already going don t know the right answer but it looks to me like practice should be done before you have to do it in
194. s not necessary to remove the upper fairing Remove two 10 mm bolts holding back of tank to frame bracket Turn the petcock to off pull the petcock vacuum line then carefully pull the fuel line a few cc s of fuel will be in the fuel line so be prepared to pour it into a gas can or something Then simply pull the tank back off the rubber frame stoppers as you lift it up and free of the fairing Tail Remove side panels One bolt each side four bolts underneath bungee hook bolts must also come out There is no need to remove the grab bar Disconnect wiring harness pull and stretch to reach over the key lock Front fender Two bolts on each side of the tire With a little patience you can remove replace the fender without dropping the wheel even with 90 profile tires WARNING Be sure to use the right bolts torques when reassembling the bodywork or it may be damaged Be especially careful with the upper fairing gas tank bolts or you might puncture the tank What is involved in removing rebuilding the engine What is the engine removal process Jeb Sat Aug 16 4 31 05 2003 It takes about 3 hours to do this having a helper for the actual lowering process helps a lot e Remove fairing sidecovers and fuel tank e Remove exhaust headers canisters can stay in place e Remove carburettors 64 e Disconnect shifter remove countershaft cover and sprocket e Unbolt radiator radiator can be left attached by hoses e Temporaril
195. s than a 130 80 6 less than a 130 90 30 lower tread depth assuming a front tire mounted on the rear there are only a few manufacturers of 120 width tires made specifically for the rear wheel anymore and a loss in ride height about 1 2 A 120 width tire is a good choice for around town riding where the quicker performance can make a difference For sport touring a 130 width tire will improve high speed straight line stability 87 How do raise the front fender to fit a 110 width tire lim Race Mon Feb 25 17 58 22 2002 1 Remove the front wheel and fender 2 Using a drill bit slightly larger than the hole in the four pop rivets drill them out from the outside of the fender 3 Remove and discard the internal steel bracket 4 Geta drill bit the same size as the bolts used to mount the fender to the fork legs 5 Carefully measure and drill new holes approximately 13 16 of an inch down from the original holes The measurement should be taken from the center of the old hole to the center of the proposed new hole note The fender does not mount parallel to the ground The center of the new hole should be equidistant from the vertical mould mark of the fork recess Mine measures appx 1 1 8 6 The front holes are difficult to drill without a right angle chuck remounted mine with only the two rear bolts but do not recommend this for street riders check my fender for tightness a lot 7 would suggest you either in
196. same for both with the 250 getting the nod for gas mileage Service requirements are almost identical for both as well being that they re both parallel twins the technology is the virtually the same The downfalls of the 500 2K more than the 250 can do a lot to the 250 with that kind of money buzzy mirrors barely useful heavier weight to have to push around the garage lesser gas mileage 55 60 MPG 250 pushes 70 MPG easily engine is worse than a nervous dog shaking around at idle and at speed here the 250 Is far superior and much smoother In my opinion the 500 is a better suited for a larger rider from a comfort standpoint feel can stretch out a bit more on it than the 250 I m 5 9 160 Ibs The 250 s brakes are better tuned than the 500 and the shifter is much smoother That may be due to the 3 500 mile difference between the two bikes Bottom line both bikes are great the 250 is now my wife s ride mainly and the 500 s mine unless she steals the keys away In time I ll make the adjustments to the 250 she doesn t push it like I do What about the ZZR250 how does it compare Damo Sun Oct 24 12 05 13 1999 My first impression of the ZZR when it was started was wow that sounds identical to a ninja which is hardly surprising seeing as they share the same engine Out on to the road and was immediately impressed by the very powerful front brake and nice firm suspension All was well in a straight line the bike felt
197. sepower by up to 10 However you also lose a bit of low end drivability in the process because the pressured air of the box is gone and the added resonance it provides as well Still would recommend this upgrade if you do a lot of work on your bike makes removing replacing the carbs much easier and can afford to spend the With newer more advanced bikes taking out the airbox would not be a good idea but with the relatively low tech engine of the Kawi 250 you can tune it to achieve an improvement over the stock setup Also note that the stock intake is more restrictive than the stock exhaust This means if you have to choose one or the other the intake mod is more effective not to mention less expensive about 50 instead of 300 for a full system exhaust Taking out the old airbox will be a pain in the ass putting in the pods will take 3 minutes The K amp N s do amplify intake noises or should say do not muffle them like the airbox does You ll also get a little more underseat storage and a slight drop in weight as a bonus How do I get the airbox out to install these Jeb Wed Oct 25 05 13 33 2000 If you re going to take the airbox out altogether it should be for good You need to remove the 10 or so screws that hold the two halves of the box together Remove the battery and the two bolts that hold the back of the box to the frame under the battery then start to work on those screws When you ve got them all ou
198. several hundred miles Most of the sporty street riders replace tires in the low thousands of miles Old guys with touring tires can sometimes go farther than that on a set of tires I ve got 27 000 on the Metzler ME33 and ME88 on my bike now think it s a good idea to replace any tires older than two years rubber deteriorates over time What do I need to know when looking for replacement tires What tire makes are available that fit the 250 Avon Super Venom Gammagirl Sat Aug 26 14 30 11 2000 The Avon Super Venom is still available in 130 90 and 100 90 for the 16 tire These tires stick to the road and are also relatively inexpensive and in my opinion outperform and outlast Metzlers and K591 s they are very popular with European racers My ex husband races them at Mosport in Ontario on his TZ250 had them on my RG500 Gamma and the bike held the road like a fly on flypaper while lasting over 20 000 KM with lots of rubber left when sold the bike And ask anyone at the flying saucer in Niagara Falls rode my gamma hard Cheng Shin Jeb Wed Aug 16 06 02 30 2000 Cheng Shin tires are what you might call a value line of tires The thing is they re not that much cheaper than a good set of Dunlops not cheap enough to justify their lack of grip anyway bought a new used set of wheels and one of them came with a Cheng Shin tire still on it thought Heck it still has a few miles left on it and so decided to sav
199. should I Consider eccecccccccsssseeececeeeceeeeeseeeceeeeeaeaeeeeeeees 49 What other components should I check i atiedaricivndn dw iedia dene ates 50 HOw do LService tile CarDS HINGES sstoriccaussc nus a kus se ste A 50 What carb components do I need to CheECK 00 eee ccccccessseeeseecececeaeeeseesceeeeaaaaesseeees 50 How do I synchronize the carburettOrs ccccceeccescccecceseesseeeceeeeeseeaeeseeeeeeeeeaaegees 50 How do I remove the carbs to work On them ccecccccsssseeeeceeeeeceeeeeseeeeeeeeaeeeeees 51 How do lad ust he DOW TlOAts rreri oean aT E A 51 How do Icleaiwthe Carb Parts 7 cccsiiatbeettaicangasiasteecon sane acai N 52 How do I get the vacuum pistons back in correctly s snnenneessssseeresssssssseerrsssssssses 32 How dolelcan the air Her niie r e Ee nud 53 HO w lt do Tl iis alae Sr zirireri ens see a T TI OE 53 How d0es weather arrect etina consceeinua see iaaldiuaclediamctacbeaewiaieestactes 53 Howdo T check Chane coolant esra AEG 54 How do I checkthe coolant leve rieien ea E decadaececedeacetoceds 54 How dolchanse the COON ereere n a 54 Howdo I workonthesuspensiol eosa ecer eesti lee ees 54 How do remove the fork pistons iiisosciaui nnn n aia a a 54 How dol replace the fork seals especi a eons alent ueetstes 55 How do I service electrical components orescence ini E a 55 HowdoTreplcethe headlie N rinri a T 55 How do I adjust the headlight beam ccc ccccccccce
200. so vacuum matches There are fancy gadgets to do this but there s also a quick and easy way to do it at home 50 Get a piece of clear plastic tubing about 3 long Place some thick liquid in it like motor oil something that won t hurt your engine if it gets sucked in Remove your fuel tank On the top side of each intake in front of the carbs is a vacuum nozzle Remove the black hose from each plug the hoses for the duration of the job and place one end of the clear tube on each fitting Let the clear tube hang down so the oil gathers at the bottom of the loop Start up your engine for a moment and if your carbs are in sync the oil will not fow one way more than the other If there s more vacuum from one carb or the other the oil will flow that direction Turn the linkage adj ustment screw you ll need either a very long screwdriver r a stubby one in between your carbs so the vacuum is equal and you are all set It may help to periodically turn off the engine for a few moments so the oil can regather at the bottom How do I remove the carbs to work on them Duke Tue Aug 29 22 33 47 2000 The carbs are a little difficult to get out if you have the stock airbox After doing this about 10 times think I ve found about the easiest method You have to loosen the rear fender battery holder and move the whole thing back about an inch to get the carbs out There are two bolts directly in front of the back wheel that hold th
201. sseennnsssssseeresssss 6l How can Tehansethetires by myself earienoniesee on E E 62 How can I balance the tires by myself nmrcsiiintsnrassnicien rae 63 How do I remove the fairing fuel tank cte 00 ccccccceccesseseeeececeeecesseeeeeeeeeseseaaeeees 64 4 What is involved in removing rebuilding the engine cccceccssssssseeeceeeceaeeeeeeseeeees 64 What isthe efigine removal process liese e n e E 64 What parts usually need to be replaced in a rebuild on eee c cc ccesseseeeeeeeeeeeeneeees 65 How much work is involved when rebuilding eee cccccsseseeseeeeceeeceeeeeseeeeeeeeaaas 65 How do I line everything up after rebuilding the top end cc eeeeeeeceeeeeee eens 66 I m having trouble putting my bike on its centerstand cc eeeecccccccecesseeeeeceeeeeeeaeeeees 66 laced Nel prep amine My DIK C tecn ee a a td fet owacwnes dtedtmaaeta 66 My DKE WONG THOM seep stata area iri eten eet neato iahcunesea N 66 My battery is good but when I turn on the ignition I get no power cc cece 66 When I try to start my bike I hear a chattering noise ce eececcccccesseseeeceeeeeeeaeeeeees 66 My bike tries to start but won t no matter how much choke I give it 0 67 My bike tries to start but won t and I see white smoke coming from the exhaust 67 My bike starts initially but the carbs flood very soon thereafter cceeeeeeees 67 My bike has been sitting for a while and I
202. t did wait until you are legally and financially independent then you can buy whatever you want just got a Ninja 250 amp have some other questions about it Do I really have to follow this break in period Jeb Sun Jan 16 17 40 50 2006 It has been pointed out that every motorcycle model Kawasaki makes comes with the same 4000 RPM initial break in limit sticker on the tach This really isn t fair because of gearing Some bikes do 50 mph or more in top gear at 4000 rpm while the Ninja 250 only does 35 mph so the bike that does 50 mph in top gear will consume 500 miles sooner It s really backwards because EX250 works harder and would break itself in sooner than say a 2 liter 5k RPM redline Kawasaki Vulcan But a mindful break in is still important This is a much debated topic some say baby it some say ride it like you stole it I m just going to put up my take on the matter backed up with a few empirical items The fact is that an engine is not fully broken for several thousands of miles During that period you have to respect it more than you would a fully broken in engine That said the Ninja 250 Is probably 95 broken in by 500 miles And it s probably 90 broken in by 50 miles Still and this is really beside the point of this article the engine is not fully broken in until 5000 miles or so when everything in the engine is completely seated at which point the engine begins to ever so slowly deteriorate just lik
203. t you should be able to break the two halves apart if you have trouble doing this then you missed a screw trust me they re hidden all over the perimeter of the box Remove the plastics and filter element at this time from inside the box then work the left half of the box out of the frame then the right It is possible to do this carefully and not damage the box The problem is the box is bigger than the frame space it occupies and is tricky to work out This is a frustrating job and can require a lot of grunt work You can make the job a little easier by removing the two bolts at the inside front of the rear fender and pulling the fender back a bit But with no airbox in the way and the modular filter pods in their place removing the carbs is as easy as loosening a few intake screws and popping them out I ve got the filters in now what do I do with the battery Jeb Thu Jul 20 21 10 19 2000 Drill two holes through the bottom of the rubber sheath that the battery sits in then use the two bolts that held the rear part of the airbox to the bike to bolt it down it may not seem like a very sturdy method but I ve had mine like this for months with no trouble Some thin washers can be used to improve stability If you have a 94 or earlier model then you don t have the sealed type battery and rubber sheath you have the larger maintenance type battery that sits directly in the box In this case you can cut the rear part of
204. t KI isnan a i nance noe 81 Where can I purchase a jet kit for my bike 0 0 eecececcccceeeeeseeeeeececeseaeeseeeeeeeeeaas 81 Can I improve carb performance without buying a whole jet Kit eens 81 What components are needed to rejet without a jet Kit oc eecececccececeeeeseeeeeeeeeeees 81 How de Padi st he 1d le Tix te iso os ivide acsaesea ten a sasmannsee eens ea ee ads 82 How docs weather afecte tine henas a a 82 lwant touperade my IMAK Cenaa aa a eeeeiodebntacmne 83 Do K amp N pods provide a significant improvement in horsepower sssesessesessssesee 83 How do I get the airbox out to install these ee cccccccccecsesseeeeeceeeeaaeeseeeeeeeseaaeeeees 83 I ve got the filters in now what do I do with the battery cece eceeccececeeeeeeeeeeeeeees 83 What do I do with the crankcase vent hose 20 0 ccccsssssesseeeescececeeeeeeeeeeeeeeeeeeeeeeeeees 84 How do I make use of the extra space under the Seat 0 cc ceeccccccececesseseesceeeeeeeaneeeees 84 How dor determine ire Size raen aestomete E a muses nlece 86 Do taller wider tires work better than the stock sizes nneeeeessssssssssssssesererresrssssssss 87 Do 120 width tires really work better on the rear nnossonennnsssssssseeressssseseresssssssses 87 How do I raise the front fender to fit a 110 width tire neneeenesseesessssssesererrsesssssssss 88 Tditke to know more about CHDONS siscsi ec naevid iil ee eens 89 AW Piatra O1
205. t canister is gone there is nothing to keep the spring from pulling the centerstand up into the swing arm and drivechain heard once of someone fabricating a bracket to hold it in place but imagine that s not all they had to do Lastly the Muzzy is designed to increase performance a bit sound good and look good One way it looks good is by really cleaning up the back of the bike with the stock exhaust cans gone the swing arm is fully visible If you leave the centerstand on it will be quite an eyesore in my opinion Sorry to discourage but it s probably more trouble than it s worth to keep it You can buy a nice swingarm stand for about 70 though which will let you do most of the maintenance the centerstand allowed The only time still use the centerstand is when I m doing rear suspension work loosely attach the stand temporarily with two 17mm bolts and put it back in the parts bin when I m done How do repack the Muzzy Mark Tue Jun 12 07 31 26 2001 repacked my Muzzy last night using the manufacturer s kit When opened up the can what little fibreglass was left in it had settled to the bottom half of the can so there was no sound absorbing material at all in the top half It s no wonder it was so loud estimate that there was only about 1 3 74 as much fibreglass material in there as there was in the replacement kit With the new packing the bike is quite a bit quieter than it was For my taste it s still loude
206. t charge could ride around all day on it but if it was parked for more than a few days it was dead Instead of spending 70 on a new one decided to go to Wal Mart and sears and try to find some suitable replacement Wal Mart carries a fine substitute for the 88 94 stock battery Yuasa YB9L A2 which is about 20 They do not carry a comparable part for the 95 model however the 88 94 battery will fit the 95 bikes but it is larger and heavier Sears has a good one though part 28 44353 It s a bit smaller in size than the stock 95 battery and it s a wet type unit not maintenance free like the stock one Benefits Well for starters it s 17 very cheap It has a 5 amp hour rating 95 has 6 Ah 88 94 has 9 Ah a 90 CCA rating vs 85 124 and it s smaller and lighter than the other two Actually this could be a good replacement for any year Ninja battery it would have to be shimmed if used in a 88 94 model though It has a shorter standby time but a comparable amount of cold cranking amps to the others After almost a year of use can report that the new battery works just fine How do I work on clutch components How do I lube the clutch cable Jeb Sun Jan 7 07 55 33 2001 Remove the bolts holding the clutch lever cable to the handlebar Remove lever end of cable so that you can hold the little knob on the end of the cable between your fingers Grab a can of WD 40 and a can of 3 in 1 oil Take
207. t if you take the fork spring washer out of the top of the fork you can take it to the store and see what size diameter you need You need to see how much sag in the front end you have before you take the top off Measure the front end topped out and with help measure how much it sags with you and riding gear on the bike You want about 1 1 4 of sag no more than 1 1 2 if it s 2 inches you need 1 2 PVC spacer or more The PVC tubing can be cut to size A guess with stock springs is that you ll need a 1 2 to 3 4 spacer with Progressive Springs you need about 1 4 to 1 2 The Progressive instructions dont call for it but there s too much sag without adding some preload it further improves the front end dive and control You put the spacer on top of the fork springs Will a fork brace improve the front suspension Paul 311 Wed Oct 3 13 15 01 2001 use a fork brace but I really can t tell a difference between having it on or off The main thing a fork brace does for me is to keep the forks from twisting when crash 4 times this season Last crash didn t even have to straighten the triple clamps The fork brace does do something There was enough flex in my front end that the edge of the tire 17 radials was cutting a little groove in the fender When put the fork brace on added a little piece of white duct tape to that spot on the fender and the tape remained untouched So the fork brace does something but sure can
208. t remember the grades but using a fairly coarse grade wet sand the part A crude but effective way to do this is to put the part in a 55 gallon trash can filled with water If this is impractical just be sure to keep the part wet A hose set to a slow dribble works well You don t need to worry about being mirror smooth just dont press to hard or you will make lines that will be difficult to hide later Once the old paint and the clear coat that is on top of the paint are removed you prime it I ve heard that hanging the piece with an unbent hanger is a good way to go Be sure to prime the whole piece at once After letting it dry for as long as the can says you apply a second coat Now after 15 20 minutes you re going to have to wet sand it again Unlike before now you re striving for a mirror smooth surface When you take off too much primer in a spot and you will reprime the whole piece don t do spot priming In my best piece it took about 7 or 8 coats to get it perfect Also applying the primer needs to be done one coat after another so make sure you have plenty of time After 24 hours of drying the easy stuff is all that s left Use paint from the same manufacture of the primer dont remember the brand used but got the primer paint and clear coat from the same company Spray the paint 10 12 inches from the piece using long strokes moving the whole arm and not just your wrist I m sure you ve seen commercials for body shops that
209. t says free to use today only would much rather practice wearing my tires on the sides than in the center It s much more rewarding What is a stoppie VFR Pilot Fri Oct 29 15 04 26 1999 Stoppie A trick often performed by squid E intentionally lifting the rear wheel off of the ground by hitting the front brake This is sometimes followed by the squid being ejected over the handlebars directly into the path of his own motorcycle What is lane splitting VFR Pilot Fri Wed May 24 22 00 48 2000 Lane splitting can also mean more than one thing e Riding between lines of stopped or moving cars legal in California e Passing a car that has moved over to give you room as long as you don t cross a double yellow line to do it this is legal in most states What is a highside lowside gabe846 Tue Jun 20 18 25 40 2000 There two kinds of non collision motorcycle crashes A lowside happens when the bike is leaned over so far that the tires no longer grip the road and the bike falls on its side This is the better kind of accident since the rider has a short distance to the pavement and can gently slide to a halt you do wear protective gear right should know had two last weekend A highside is when the bike s front or rear tire loses traction and suddenly regains it with one of the wheels out of the line of travel The bike reacts with a whip like action spitting the rider off the high side This is b
210. t with the choke partially on all the time which seemed to make it run OK Once into the upper part of the RPM range though the choke makes no difference to 75 the mixture as everything is wide open and mixture is being determined by the main jets which in stock form are way too lean to be running with a non stock pipe If you have to run without jetting go easy on the heat until you can get the right jets installed The difference in performance beyond possible damage is well worth the cost and time involved in jetting What if I m just installing slipon canisters do I still need to rejet Duke Thu Jul 20 20 44 55 2000 You do not have to rejet with slipons as they don t significantly change the flow characteristics of your exhaust system Rejetting is however always a good idea especially if you have the time to experiment and get your jetting just right As we ve seen here recently the optimal jets can change significantly depending on the altitude at which you live There s no magic formula involved with the stock jetting They ve merely jetted it for an average If you are particular and want the most from your little engine splurge for a jet kit and the adjustability it offers Can I get a better exhaust sound without replacing the stock pipes Brent Thu Apr 26 04 05 08 2001 You can take the canisters off and bring them to a machinist to cut off the endcaps cut out the baffles and place the endcaps ba
211. t you need to ride well in the rain Get a sturdy pair of rain pants and rain gloves or covers XXX L dishwashing gloves are good to pull over your regular gloves for short distances Two plastic grocery bags make great emergency rain booties they re tougher than they look and free Another must have is a FogCity shield for your helmet visor it ends fogging completely and mean completely It s just 15 or so and is a great thing to have J ust ride like you usually do just smoother and a little slower You d be amazed at how far you can actually lean on wet pavement and modern brakes work fine once they heat up The important thing is to practice Sell your car and ride everyday 19 Earplugs VFR Pilot Tue Sep 19 13 11 37 2000 There is absolutely no doubt that exposure to noise levels in excess of 100 db causes cumulative hearing damage Worse yet this is hearing loss that you can never recover Once it goes away it s gone forever Eventually you are likely to develop tinnitus a constant singing or whistling in your ears that overlays everything you hear No fun The best solution that I ve found is a pair of custom fitted earplugs made by an audiologist These are cast out of silicon from moulds made in your own ears and contain a tiny valve that allow low level sounds to be heard while at the same time cutting out everything that s above a given sound pressure Mine cut in at 80 db and make life a lot easier du
212. termine if you are using the middle of the available travel on your shock forks The middle range in the travel tends to give the most even damping from what I hear and it will also help keep you from topping out or bottoming out if you have the sag set correctly 79 What good does reducing unsprung weight do Wes Thu Jan 11 14 22 01 2001 e Unsprung weight is anything on a bike not being supported by the suspension e g wheels tires brake rotors chain sprocket swing arm e Unsprung weight is undesirable because the more weight an unsprung component has the more inertia it has omv e The more unsprung inertia there is the harder it is for the suspension to absorb changes in inertia by exerting a compensating force as it has to do more work f ma p nv a4 change in v conservation of momentum energy e So less unsprung weight means the suspension has a faster reaction time to bumps in the road causing less jostling for the rider e Forces not absorbed by the suspension are passed on to the components on top of the suspension including the rider e So the higher the ratio of sorung to unsprung weight the smoother a ride you get e The smoother the intrinsic ride the stiffer you can make the suspension without rattling the rider s teeth out e The stiffer the suspension the better the handling and feedback I want to improve my carburettor jetting Why would I want to change my jetting Duke Thu Jan 13 06
213. tersection should have known better than to brake that hard in the city screwed up bad Since it was a rear end collision and a witness saw that the light was changing the other driver s insurance paid for the damage to my bike From the insurance company s point of view the accident was clearly the fault of the other driver but haven t allowed that to happen again Riding a motorcycle is dangerous There are a lot of things you can do to be safer go to school keep your equipment in good repair and there are a lot of things you can do that improve your riding ability which paradoxically put you in danger of crashing riding in the snow following better riders in curves but to make blanket statements that you should never crash due to your own mistakes or that all riders will crash simply doesn t work Necessity of proper gear Brent Fri Jun 29 19 06 09 2001 Well yesterday another one of my friends went down He was headed over to a friend s house a few block away and decided not to wear his helmet or a jacket Well he took a fall at about 35mph on his Ducati 996 DOH and did some backsliding down the asphalt Then he tumbled up a curve slid in some grass and got cut up be the sprinkler heads in the median He didn t have any broken bones but lost a lot of skin off his back and had several abrasions to his head The moral wear your gear no matter how short or hot the trip is Last April my good friend went down at 40mph on
214. th him it doesn t really look any different than the stock tire if looks are what you re after The racers like Paul 311 are actually using a 120 80 16 rear tire as it said to perform better than the 130 size To be honest the K630 tires stock OEM are fine for all but the most aggressive riders and the racers I ve ridden mine fairly hard uo 3 RAD with no problems at all The only place they ve wandered was riding Deal S so in the rain but that s to be expected 60 Do taller wider tires work better than the stock sizes Jeb Wed May 2 23 03 47 2001 The stock tire sizes are pretty good It s getting harder to find 100 80 and 130 80 tires though so it s good to know what the other options are Taller tires alter your steering geometry this can be good or bad depending on which tire you change A taller rear tire will steepen decrease the geometry making the bike turn faster a taller front will increase the steering angle Increasing both front and rear tire heights can be good because you get an even steering angle close to stock and get added road clearance and trail length provides stability A taller rear tire will also increase the final drive gearing a bit lowering cruising revs while a taller front will increase speedometer accuracy Wider tires generally slow the steering of the bike down They also alter the contact patch as the tire is pinched in the rim Wider tires can provide better straight
215. the airbox off with a dremel works just as well just not quite as clean a job Or you might be able to more easily build a small cage for it out of aluminum brackets or something 83 What do I do with the crankcase vent hose Jeb Sun Sep 9 22 18 20 2001 The crankcase breather tube is an s shaped tube that sticks up from the crankcase below the carbs It is normally routed to the airbox so case gasses can be taken back in through the engine intake and blowby oil reabsorbed to the sump when the mist accumulates and drips back down into the case With the airbox gone this vent is unchecked and the crankcase has no protection from the elements except for the s shaped hose Also if the hose is not otherwise dealt with then the oil mist from the engine will cover the top of the case and the bottom of the carbs The hose could be plugged but then the case would be pressurized not a good idea There are two practical filter options buy a permanent cleanable filter looks like a small K amp N pod or get one with a replicable element chose to do the latter since cleaning the crankcase filter needs to be done much more often than cleaning the carb intake filters selected a compact filter with a good sized surface area part number B23124 Purolator or BF305 Deutsch This filter has a terminal connector of 1 2 O D just like the breather tube used a 1 length of 1 2 I D hose to couple the parts The filter has a low prof
216. the insurer the fax number of the motorcycle dealer also MSF course probably gets you a discount e Insurance company faxes insurance confirmation to the motorcycle dealer e When the dealer has confirmation that you are licensed and are insured the finances are next e The bike is paid for and you ride it home The requirements might vary depending on where you live and the dealer you are doing business with What riding gear should I have Helmet should wear a helmet right VFR Pilot Sun May 14 21 55 25 2000 Most motorcycle accidents occur at relatively slow speeds and in city traffic In fact the most frequent fatal accident involving motorcycles is the one where a car left turns directly into the bike s path causing the bike to bury itself in the car s side panel and the rider to fly over the top usually landing head first You don t have to be going very fast for this one to kill you While I d say that the State has no business telling us that we have to wear helmets under penalty of law there is another much older law at work here Known as Selective Evolution Survival Of the Fittest or just plain Thinning the Herd it means that those who always put on their helmets are more likely to survive and those who don t aren t Your choice 15 How much should I plan on spending VFR Pilot Fri Nov 12 00 33 50 1999 Helmet prices are largely a you get what you pay for proposition The more expensive ones usually
217. ther 250 s and a whole lot more went to the local dealer and looked at one and when sat on it and pulled it off the side stand almost threw it across the room was used to the Sportster s 525lbs what a difference That dealer had a bad rep so looked elsewhere Another dealer who was expecting some Ninja 250 s in November practically refused to sell me one you ll outgrow it he said wound up buying one used cheaper The Ninja out runs out accelerates and easily out turns the Harley and gets better gas mileage Whipping it around corners is about the most fun I ve ever had Other people can t believe its only a 250 If eventually move somewhere else that has a garage I ll move up to a bigger sportbike Till then I ll be building up my experience and skills sportbike skills on the weekdays and cruiser skills on the weekend 103 Best bike for your dollar Leon Thu Jan 20 14 46 24 2000 My first bike was a Honda CB200 that bought for 175 in 1981 It didn t run it had been rusting in the back yard for a couple of years cleaned it up and got it running most of the early practice was to see if the bike would stay running After a month or so hauled it up to the DMV to get my license this was back in the days when the riding test consisted of Take it out there on the street go to the end of the block make a U turn use the turn signal when you come back into the lot here So did Ok you passed About a dozen bi
218. there are two serious choices for helmetry Arai and Shoei You must determine if you have a Shoei or Arai head If the Shoei feels like someone giving you a noogie right above your forehead after 10 minutes get the Arai don t know what an uncomfortable Arai feels like cuz have an Arai shaped head think the RF800 is a pretty good helmet it s not the best Shoei but it s a far cry from the cheap ones It should be good to wear all day and it s really easy to remove the face shield How do I keep my visor from fogging up MattH Fri Sep 27 07 57 53 2002 Rain X makes a special formula for use on plastic but don t use it use Nu Finish car wax like stuff or Lemon Pledge You have to reapply Pledge more often but it gives your riding environment a nice clean smell especially handy in cow country They both do the same thing keep water vapor from collecting and allow water to bead up and roll off more quickly also carry the breath deflector for the helmet and only use it if it starts to fog up inside I ve heard that Rain X standard glass formula is not good for plastic 16 Jacket Leather vs Cordura Leb FriJan 12 11 55 17 2001 It s difficult to say which is better Leather offers better abrasion resistance and sustains damage better in a getoff it is also generally heavier more difficult to care for and not as versatile Cordura a high denier nylon blend breathes better is waterproof doesn t look as sup
219. they should be cheap in the US As for Teknic owned a pair of Violators for about two months they were okay but expensive though they did hold up well to getting crashed at the track Widder heated gloves Wolcott Sun Feb 20 07 44 47 2000 I ve had Widder Electric gloves and vest for 6 years now and they are great They extend my riding season a full month at both the beginning and the end of the season just got a Competition Accessories catalog and they have them listed They re at http www competitionaccessories com your local shop should have them too The prices seem to be about what paid Their prices are gloves 90 electric thermostat 70 vests vary see the catalog recommend the electric thermostat as have the old one and it cycles on and off so you get cool periods The new one is constant and reduces flow from the battery as you adjust it down Comes with a harness with a connector lead to the battery Snake the lead under the seat from the battery out to the tank plug it in or out when you get on or off the bike also use the battery connector lead to attach my Sears Battery Tender 27 recommend the vest too If you get one fit it snug so you feel the warmth directly on the body Mine is a little loose and it is bulky under outer garments You want to wear it close to the skin over a turtle neck and under a fleece The vest with the collar can be bulky at the Aerostitch collar closure notice the new
220. tice it unless you re very aggressive e The major concern is that you lose cornering clearance When dropped the rear only 1 1 4 inch could still lean over quite far without touching anything down When went down 1 7 8 inches however the side stand hit on the left and the pipe hit on the right The center stand does not hit first You lose a lot of the aggressive cornering ability that this little Ninja is noted for However for starting and conservative riders it should have little effect e Regarding the cornering clearance My experience was with an EX500 shock so stock shock cornering clearance will be much worse Strongly recommend installing a used ex500 shock with this modification Note that Ninjagrrl is doing fine with stock suspension but she only lowered it 1 1 8 inches Why is important to raise lower each end of the bike together Paul 311 Wed Feb 9 23 11 53 2000 On my race bike have found a set up that works really well Whenever make a change which has a side effect changes the ride height always try to make a change to counteract it and get things back where they were There are two things that change when you change the height of one end of the bike or the other a fork angle b weight distribution Making the fork angle steeper closer to vertical makes the bike steer more quickly This can make the bike feel twitchy and unstable if you take it too far Getting more weight on the front end is a
221. tra is this The 250 can give you a lot when your riding skill and experience exceed what the bike can give then you ll be ready for a bigger bike But that can take a very long time fell in love with my 250 in 25 years of riding it is the most fun on two wheels of the four bikes I ve owned My last bike was a 750 and rode it for 15 years it was a nice bike with plenty of power but it was also heavy My 250 Is light as a feather in comparison and for around town and back road twisties it s everything want and need Can I get some stats specs for the bike Specifications and Performance Statistics Specifications Engine 4 stroke Parallel twin DOHC Liquid cooled 8 Valve w counter balancer Displacement 248cc Starting Electric Bore x Stroke 62 0 x 41 2mm Compression Ratio 12 4 1 12 Carburetion Ignition Spark Plug Transmission Clutch Frame Rake trail Suspension front Suspension rear Wheelbase Wheel travel front Wheel travel rear Tire front Tire rear Brakes front rear Overall length Overall width Overall height Ground Clearance Seat height Weight Dry Wet Max Load Fuel capacity Fuel type Oil capacity 0 60 mph 0 100 km h 1 4 Mile Maximum Speed Max Horsepower Max Torque Fuel Efficiency Keihin CVK30 2 Constant velocity Diaphragm type CDI electronic advance NGK CR8HSA CR8HIX CR8HVX option CR7HSA CR7HIX 6 speed Constant mesh Return shift
222. trailer rig can help but not if you have to tuck right in behind him to get any benefit This will depend on the angle and speed of the wind do not get right alongside one and try to stay there These guys often can t see you and will change lanes right on top of you with no warning They also occasionally blow right over in high crosswinds Not a good time to be on the downwind side unless you ve always wanted to be a waffle 4 Watch the upwind side of the road ahead of you Billboards parked trucks cuts and stands of trees will cause the crosswind to suddenly stop and you to suddenly zig If you know that it s about to happen it s much easier to cope with 5 If you absolutely must ride in a heavy crosswind take a short break every twenty minutes or so Your concentration will need a rest Note Forget Beaufort In the Southern California deserts we have our own wind scale Tumbleweeds blowing across road mild crosswinds Sand blowing across road moderate crosswinds J ackrabbits blowing across road stiff crosswinds Rattlesnakes blowing across road heavy crosswinds Trucks blowing across road time to get off and walk Maximum lean angles VFR Pilot Tue Jun 20 15 58 17 2000 If your tire pressures are correct and the tires are in good shape you can safely lean a Ninja 250 over until the peg feelers start to scrape It s not a good idea to go much further than that as the centerstand will drag at really high lean angles and
223. ts If you need to add coolant add a 50 50 mixture Never use any coolant other than one specified for motorcycles Other coolants may have abrasives in them that clean other systems but will damage a motorcycle system Fluid levels should always be checked with the bike straight up resting on its tires unless the manual states to do so on the centerstand The slight elevation a centerstand or swingarm stand gives may give you an erroneous reading When in doubt follow the manual then check the other way to see if there s any difference How do I change the coolant Patrik Mon May 15 23 02 47 2000 There are 2 coolant drain plugs First open the filler cap then remove the first one It s on the water pump it s a 10mm bolt as opposed to the 8mm mounting bolts Watch it the water comes out with quite a bit of pressure it goes straight out the side Then drain the coolant in the cylinder the plug is on the front between and slightly under the pipes The expansion tank is probably most easily drained by taking it off and pouring it out the cap If you want to be sure to get all coolant out you should probably flush once with water as well You can t fill it at the expansion tank J ust fill at the filler cap at the radiator and when it s full start the bike and let the engine idle this will make the air bubbles come out and you can fill more When the water starts getting hot and you can rev the engine without having bubbles come out
224. ts that don t get fully lubricated during the first few seconds after startup while pressure is established will suffer less frictional wear Synth oils also maintain their viscosity more effectively over time and under different engine loads Ultimately synth oils just lubricate better What oil filters are available lan Thu Jun 19 17 17 33 2003 You can find the following oil filters which are a direct replacement for the Kawasaki unit sold by dealers Most are around half the price of the Kawasaki filter Amsoil SMF 101 CarQuest CFI 89941 Emgo 10 37500 Fram CH6012 of CH6009 12 is ideal the 09 s o ring is oversized Hastings LF571 Honda 15410 426 010 or 15410 300 024 Kawasaki 16099 003 K amp N KN 401 NAPA 4941 Perf Form J 501 Purolator ML16812 STP SMO 12 or SMO 09 12 is ideal the 09 s o ring is oversized Triumph 1210031 Yamaha 36Y 13441 00 At least one of these filters will be available at any reasonable auto parts store such as AutoZone Pep Boys Schucks Kragen NAPA WalMart etc If you can t find these brands at your favorite auto parts store check to see if they have a cross reference chart for the brand of filters they carry most filter manufacturers do Cross reference their brand to one of those filters listed above 40 How do I service the final drive How do I clean the drivechain VFR Pilot Fri Nov 2 01 43 28 2001 use a spray can of WD40 a spray can of O ring chain
225. ull you out of the course The only other thing can think of is the one guy that had to pull out because he completely lost confidence in both himself and us He was riding quite well he had been cautioned a couple of times to slow down and take it easy but then locked the front wheel and fell at about 15 mph About 10 23 minutes later the same thing happened again After the second incident he wouldn t use the front brake anymore plus he was so spooked by the first two falls that he wasn t paying attention to what we were trying to teach had to ask him to leave This year I ve taught 3 courses 10 12 people per course all have completed the course and taken the riding test but about 1 per class has failed the test To my knowledge all of them passed the retest when they returned the next week Initial failure rate in Maryland is 10 to 20 More than half of those that return pass the retest The best advice can give you before taking this course is study the material before you get to class arrive in class ready to take the written test that way you don t have to study at night Get plenty of rest between sessions This is a very physical class sleep is more important than studying if you live more than 20 miles from the course consider getting a motel room so you can rest instead of commuting Finally if it s hot drink plenty of fluids dehydration tires one out and gives muscle cramps What benefit will get from it Ke
226. ully faired It has a windshield a covered engine and plastic that goes all the way down to the bottom of the bike 33 Biker Speak What is a Squid Ninja Grrrl Fri Oct 29 08 15 06 1999 A squid is a youthful rider that gets ahold of a high powered sport bike and does a lot of stunts and extreme riding not fully realizing that without training and experience disaster is near We worried about one of our young riding partners when he got his F3 He turned out to be a very good rider only a small squid therefore gaining the name of J ohnny Calamari Me on the other hand being such an overly cautious rider was constantly referred to a jellyfish At least still have all my cells What is a burn out Terry Thu Dec 21 18 49 04 2000 Stand on the ground while squeezing the front brake and pressing down on the handlebars with as much weight as you can Rev it to 8 10k and dump the clutch while at the same time twisting the throttle wide open There you go start with the rear wheel on wet asphalt to make it even easier Have fun wasting your back tire if you choose I ll admit did it myself a few times because was curious but quickly realized there is no skill involved in a burnout A trained monkey can learn to do one Since it is such an easy act anyone can perform most motorcyclists that see another will quickly lose respect for that individual unless they see a truckload of rear tires behind him with a sign tha
227. ully measure and drill new holes approximately 13 16 of an inch down from the original holes The measurement should be taken from the center of the old hole to the center of the 61 proposed new hole note The fender does not mount parallel to the ground The center of the new hole should be equidistant from the vertical mould mark of the fork recess Mine measures appx 1 1 8 6 The front holes are difficult to drill without a right angle chuck remounted mine with only the two rear bolts but do not recommend this for street riders check my fender for tightness a lot 7 would suggest you either invest in a right angle drill chuck or use a dremel tool Do it right or don t do it at all 8 When remounting the fender place a suitable flat washer between the outside of the fender and the mounting point This will help prevent gouging the plastic 9 Remount the fender and tire and verify clearance Do not re use the steel bracket Make sure you check often that the mounting bolts are tight Here is a picture of the completed project 6 2 o Si J a d x Q Qe _ o G gt N wy gt amp ks S m lt S f Ai Haon How can I change the tires by myself SteveS Tue Sep 12 11 58 58 2000 Mechanically doing the tire yourself isnt bad at all It does take a bit of physical effort and some time and a few special tools Heres what you ll need Bea
228. up all the pleasure that riding brings just because of a careless mistake and a group of nay sayers Three years ago had a pretty bad accident Broke my left hip The accident wasn t my fault lady decided not to stop for the stop sign and hit her and there was absolutely nothing could have done to prevent it But here s what learned nothing beats motorcycling for sheer enjoyment Even if you re careful things can still get pretty bad but the rest of the time things are just perfect What s the Deals Gap trip all about Duke Sat Aug 19 02 40 35 2000 The 250 Nationals has become a semi annual trip we ve been doing since the Spring of 99 This is a Safe fun relaxing enjoyable trip for riders of all skill levels through some incredibly beautiful mountain areas We are all very careful riders much more interested in learning to ride our little bikes well in the twisties than performing speed demon esque feats of bravado The Deal s Gap area and Surrounding mountains are some of the best riding touring areas in the Eastern US The Gap isn t really as scary as everyone wants to make it out to be You can go as fast or slow as you want Speed is really relative The slowest you could possibly go on a Ninja 250 Is still faster than the 1960 something Ford pickup with the bed full of plastic milk jugs that you re very likely to run across on any given day on the Deal s Gap road The Gap is really only 15 minutes of the who
229. usian e addi isbbemetacoiataen 94 6 I want to mount up bigger wheels ccceessssessssseeeeeeeecececeeceaaeeeeesseseeeeeeeeeeeeeeeeaeaegeas 94 DSC WILY spc AEE N EE AE oy as ous conse ua O E own aera eae eet ena nase E eee 95 DELO E mrad cere emer eater ieee AARC Re rtiw A era ervey e eAATIT en verer Cnet CRT aT Tn eT 95 GlolmNC RCN atc aa te rnrns intr ret mre errrene rer trot a teentnne er tre tere tea int E eae at ane ae 95 DANO tire tu ERA A hens ves pees N as 95 DANK DAS eter al saree otstls sire caccr ave taen tae vase avienbadenatunaain ancdacueasnnan ten a epee anaes 95 FID AM UN YO lt a cose cl ssid cra crs A IE E AT E AA OA E E tical keaton EE AEA an one aeixesen 95 SAIS DAS Snee A eleta le aries Beanies aero 96 DEM A euena a a a a ote 96 I want to know more about headlight modulators cc eeeesecececeeeeeeeeeceeeeeeeaseeees 96 I want to wire extra brake lights into those empty rear sockets ccseeeeeceeeeeeeeeeeeees 97 I want to make the stock front flasher pods into DRL S cccccceseseeeeeeeeeeeeneeeeeeees 97 I want tail lights with more brightness Comntrast ccecccesssssececececeesesseeeceeeesaaasneseeees 98 Aesthete WO GIT IC ALU INS asses cS acer Sead eset sp ches hess hens wa ae lyda N 98 I want to remove the decals from My DIKe 0 0 cece cccccccccsesececeeeeeaeeeseeceeeeeseaeeeseseeeeeeaas 98 lwant to repaint miy Dike sss inca die Seis a8t ace excaluiad E a 99 L Wantt
230. ut left hand on left hand grip 4 Put right hand on handhold Handhold is either the metal bar by the passenger peg helmet lock my choice or the grab bar Bend at the knees not with your back 5 Push down on centrestand footpad until one of its feet touch down 6 Push the bike away from yourself until the other centrestand foot touches down 7 Push down on the centrestand footpad with all your weight and pull back and up mostly back with your right hand it may help lean your right knee into the side of the bike 8 The bike should pop right up I need help repairing my bike My bike won t run My battery is good but when I turn on the ignition get no power Leb Mon Feb 21 03 13 25 2000 This is probably because of a blown main fuse This 30 amp fuse is found in the starter solenoid unit next to the fuse box When try to start my bike hear a chattering noise Greg Tue Mar 28 12 47 43 2000 Most likely there is just enough juice left in the battery to actuate the starter relay but not enough to turn the motor itself That is your clicking noise This happens to cars too Also check that the screws holding the cables on to the battery are snug If the battery and its connections are okay then try this Get someone more mechanically knowledgeable to carefully stick a screwdriver across the starter relay main leads dont touch the metal part of the screwdriver though If the motor turns 66 over fine then have them
231. uying a Dyno et kit Their needle has an excellent taper for the 250 s needs As the needle Is raised to it s highest point it no longer has a part in controlling mixture and the job goes to the Main Jet which resides at the bottom of the tube from which the Needle Jet was raised This is the maximum amount of fuel which can be delivered to your engine Thus the main jet affects your engine s performance at the higher RPM range and is critical in tuning your engine to deliver maximum power The point of this is to deliver the optimum mixture of air and gas 14 1 ratio believe at every RPM The process is difficult which leads to your carburettor having the three different fuel circuits which are each used for a different part of the RPM range pilot needle main Thus the invention of fuel injection in which this is all figured out by a computer What is jetting Duke Tue Jan 11 15 39 41 2000 Carburettor jetting is the fine art of adjusting the jets inside your carburettors to provide optimal fuel flow into your engine A couple different companies sell jet kits that include 2 adjustable jet needles and 4 sets of 2 different sized main jets to allow you to accomplish this goal If you modify your exhaust or intake you will need to also adjust your mixtures in your carbs due to the increased airflow which will cause a lean mixture Depending on what mods you make you ll use Stage 1 or Stage 3 Both are included in the kit th
232. vest in a right angle drill chuck or use a dremel tool Do it right or don t do it at all 8 When remounting the fender place a suitable flat washer between the outside of the fender and the mounting point This will help prevent gouging the plastic 9 Remount the fender and tire and verify clearance Do not re use the steel bracket Make sure you check often that the mounting bolts are tight Here is a picture of the completed project Yr oe 6 Q D Si J a d Se 2 Reis ty WoS oN re Pe j 88 I d like to know more about clipons What are clipons Thundercat Mon Nov 29 16 28 34 1999 Clip ons are kind of like two piece handlebars that clip onto the upper portions of each fork leg Though the 250R has two piece bars they are not true clip ons since they attach to the top triple clamp and are fairly high To see the difference look at a stock bike then check out Damo s pictures 2nd and 6th from the top They usually result in a more forward and lower riding position great for moving weight forward and getting good front end feel while racing Usually the more radical sportbikes will have them mounted to the fork tubes directly below the top triple clamp The drawback to using them is that they can be uncomfortable over longer periods of time How do these improve handling Jeb Wed Jul 19 11 43 18 2000 Steering was positively affected in two ways First the ridi
233. vin Sun Nov 14 05 06 25 1999 totally support the course Not only do you learn critical life saving skills during the course you might be able to pick up a huge insurance discount as well There are many little things you learn in that course that you could never pickup from learning from friends or especially by yourself I ve read that the course equals about 2 years riding experience or something personally think that s kind of far fetched but its definitely worth the money learned a lot in the crash course think they should make that course a LAW or mandatory for all motorcycle riders A lot of accidents could be prevented and riders saved if it was The course is basically designed for the new rider but most of the time people who show up for it are those that have ridden before In a class of about 15 it was only me and this other guy that had never ridden before One guy even rode his brand new Harley to the course He was doing it for insurance supposedly his company gave him a ridiculous discount Hope this helps in your decision nothing but good things will come out of taking that course But aren t those courses just for total newbies Craig Sat Nov 13 12 08 27 1999 Even a seasoned veteran will glean something from the course Tim is correct it does break bad habits and teach he proper set of skills necessary to safely interact with other traffic took the course last weekend 12 in the class two which had nev
234. when I stop Jeb Mon Sep 3 07 57 05 2001 This is due to vapor expansion and it is normal especially on warm days The pressure inside the tank is always changing and restablizing as fuel is pulled out by the carbs and air gets in to fill the space left Add the slow process of gasoline vaporization to the mix and you get a slight whine coming from the vents 38 Maintenance Repair need advice for maintaining my bike How do I change the oil What is the oil change procedure Jeb Sun Jan 7 07 55 33 2001 Here is a diagram of the filter assembly right Warm up the engine Turn off the engine and let it sit for K Sa _ a few minutes place the bike on centerstand Remove the drain plug bolt on the bottom of the engine over a 3 Fi qt container don t burn yourself Once the oil flow has slowed to a drip replace the bolt and tighten to 14 5 16099 Eri a Ib fts don t overtighten it unless you really dig oil leaks Remove the oil filter bolt and filter retainer just in E front of the drain bolt More oil and a dirty filter element will come out Be sure to keep all the O springs grommets in order Place the new filter STP SMO 12 SMO 09 will work if you can t find the SMO 12 on the retainer and replace C D the assembly again torquing the bolt to 14 5 ft Ibs 500 Open the filler cap on the right side of engine Fill w iit 1 5 qts of your favorite oil Wait a minute then add a r
235. wouldn t think that the extra miles will make much of a difference try to adjust the valves every 10 000 miles but do so more often if I ve been riding faster than normal would guess that fewer than half of the Ninja 250s sold ever get their valves adjusted never did mine until discovered how much of a difference it made in the way the bike performed With the valves set wrong the bike runs just fine in most cases with them right it runs noticeably 46 better There are probably several other adjustments the bike could use that just don t know about The valves are also rather intimidating to the novice user They need to be adjusted within a couple thousandths of an inch or else the bike won t run at all measurements of that accuracy are not normally done by the average person What is the hot soak valve cleaning method Jeb Wed Jul 23 01 12 15 37 2001 Over time carbon deposits and varnish can build up on the valves piston crowns and intake tract These deposits are usually greater when the bike is frequently used to make short trips as the engine does not reach full operating temperature Frequent idling and low rpm riding especially when the engine or ambient temperature is cold can also contribute to advanced carbon build up Some carbon on the valves is not harmful but as the deposits accumulate they can cause poor performance Valve surface area increases creating turbulence and disallowing complete intake and ex
236. xygen in the air In reality your bike my bike the fuel to air ratio varies from 14 7 1 quite a bit More air less gas lean more gas less air rich Your job when jetting your bike is to get as close to this ideal 14 7 1 ratio as possible which also produces the most power The problem is denser air Cold Dry produces a leaner condition and thinner air hot wet produces a richer condition The other problem is that the weather is constantly changing So in the end yes you can constantly chase the perfect mixture thus the advantage of fuel injection which is constantly adjusting for weather or you compromise and set up the jetting to work well at about 70 degrees a happy medium A lean condition can hurt your engine over time but you would certainly know it s lean spitting sputtering etc ran 92 mains in my carbs for a long time and had no problems until pulled my airbox top allowing more air to flow thus creating a leaner condition and could immediately tell it was too lean 105 s stock are in it now and it runs very well Why did I pull my airbox lid Why do people use K amp N pods More air in more 02 in more gas in more power 82 I want to upgrade my intake Do K amp N pods provide a significant improvement in horsepower Jeb Sun May 14 13 41 32 2000 K amp N filter pods part RC 1822 pull in more air than the stock airbox does Combined with the proper jetting this can help to increase peak hor
237. y pull the top main hose going to the radiator filler neck and reroute it below the frame you ll lose a few ounces of coolant reattach Pull the small overflow hose Unbolt the thermostat from the frame e Remove the front engine mounting bolt and two front mounting wings along with their coils wires e Disconnect remaining wiring two connectors at rear of engine starter battery ground temperature sending oil pressure radiator fan and neutral position wires e Support motor with a floor jack under the oil filter remove 2 rear motor mount nuts bolts e Lower it slowly and see if anything else is attached Note If you are removing the engine to rebuild it it makes more sense to drain the coolant and oil before pulling it The steps above to avoid draining the coolant are assuming a basic engine swap procedure What parts usually need to be replaced in a rebuild Paul 311 Mon Oct 8 19 26 17 2001 These are the things replace during my annual race motor rebuilds rings 0 5mm new pistons 0 5mm connecting rod Big end bearings 4 halves main bearings 1 amp 3 Need 4 halves 2 Need 2 halves usually don t replace the balance shaft bearings 4 halves cam tensioner spring 92081 1984 cam chain 92057 1210 head gasket 11004 1312 base gasket 11009 1572 clutch cover gasket 11009 1872 alternator cover gasket 11009 1873 shift shaft seal 92051 005 copper exhaust crush washers 11009 1866 qty 2 There are three
238. you can lean way over get on the gas do mid turn swerves to avoid obstacles and stay stable through bumps How much faster light years How Spend money on shocks and forks The stock 250 Ninja is comfortable but sloppy so it s easy to improve How does modifying the steering geometry help Paul 311 Wed Feb 9 23 11 53 2000 On my race bike have found a set up that works really well Whenever make a change which has a side effect changes the ride height always try to make a change to counteract it and get things back where they were There are two things that change when you change the height of one end of the bike or the other a fork angle b weight distribution Making the fork angle steeper closer to vertical makes the bike steer more quickly This can make the bike feel twitchy and unstable if you take it too far Getting more weight on the front end is a good thing The Ninja 250 is pretty light on the front end and will tend to push the front end with the stock ride height Raising the rear a little or dropping the front a little helps cure this Unfortunately ride height is a relative thing so set up is difficult to translate from bike to bike and will be affected by things such as a sag which can be adjusted by changing preload b position of the forks in the triple clamps C tire profile d longer or shorter rear shock Preload is what you change to set the sag Checking sag is one way to de
239. you re set put the filler cap back on How do I work on the suspension How do I remove the fork pistons Gazoo Wed Aug 30 17 42 27 2000 1 Go out and buy a gear puller Sears has them for about 30 If you re on a budget you might also try a battery terminal puller from Autozone for 3 2 Jack up the front of the bike so you don t have to worry about the front forks collapsing while your taking the springs out 3 Remove the handlebars by unscrewing the four hex head bolts on top of the upper fork holder 4 The fork springs are held inside the forks by a piston that thing with a dimple in the top which is secured by a snap ring Use the gear puller to push the piston down so you can pop the snap ring out with a pair of pliers 5 Once the snap ring is out you can loosen the gear puller but not too fast The piston will rise very slowly because its in there tight but once it reaches the top it will want to shoot out like a champaign cork J ust in case don t put your face over the fork tube while doing this Let the gear puller slowly ease the piston out 6 Underneath the piston are some miscellaneous hardware like a large washer and a spacer The spring should be visible once the hardware is out Replace it and assemble in reverse order 54 How do replace the fork seals Brent Tue May 28 18 09 36 2002 Disassembly Remove the top plug and fluid from the forks before removing them from the bike Once the forks are

The Kawasaki Ninja 250 FAQ

Contents

Download Pdf Manuals

Related Search

Related Contents