INSTRUCTIONS 915-11CAM
Contents
1. engine damage Next check the available travel of your valve springs to assure that they c do not coil bind with the increased cam lift Place a valve spring into a l vise or arbor press and compress until eee A coil bind occurs Measure with your SSS B machinist rule or calipers Subtract E HEIGHT this dimension from the installed height of the valve spring using the 060 safety margin as listed above to calculate the total spring travel available see figure 3 Again if your valve lift exceeds the available spring travel you must install new valve springs The last thing to check on your valve springs is the seat pressure Take them to your local machine shop or use a valve spring pressure tester like our p n 913 81103 Compress the spring to the measured valve spring installed height dimension and check the pressure reading If your valve springs pass all of the above listed requirements they may be reused If they fail on any one of the test criteria they must be replaced with the recommended valve spring set Leave the checking springs installed on the 1 cylinder you will use them again to check piston to valve clearance in a later step 5 Remove timing gear from crankshaft a puller is normally required Clean and inspect the cam bearings and each lifter bore for scoring nicks or other damage Wrap a strip of scotchbrite around a long screwdriver and clean any varnish from each lifter bore On fresh engine builds the lift2. 915 1 1CAM Speedway Motors Inc Dec 2008 PLEASE READ INSTRUCTIONS COMPLETELY BEFORE STARTING YOUR INSTALLATION IMPORTANT NOTE Recent changes in today s oil products and internal engine design as well as other factors have lead to an increase of premature camshaft failures The hardness of the lifter base or the taper of the cam lobe are often suspect however in almost every case it has been determined that the failure is unrelated to the camshaft manufacture or quality The three things with the greatest influence on camshaft durability are PROPER CAMSHAFT INSTALLATION SET UP AND BREAK IN PROCEDURES This instruction sheet will provide the necessary steps that when followed accurately will assure a durable and long lasting camshaft installation Some of the topics may not apply to every application but all of the information will be beneficial during the camshaft installation process If you do not understand these instructions or have questions do not hesitate to contact our tech department for assistance Failures within the first hour of operation are almost always the result of improper installation procedures ADEQUATE LUBRICATION Another major factor in the increase of flat tappet camshaft failures could be your favorite brand of engine oil Due to ever tightening federal environmental regulations the EPA has mandated a reduction of some of the EP extreme pressure additives in traditional motor oils such as zinc
3. ZDDP and manganese Many race oils for off road use only and over the counter diesel oils such as Shell Rotella T still contain those additives Look for oils meeting Cl 4 or Cl 4 Plus certification requirements Failures that occur after the first hour of operation but before the next scheduled oil change are normally due to the lack of EP lubricants in the oil that is being used Synthetic oils are not recommended for use during the break in period to the first scheduled oil change INTERNAL ENGINE MODIFICATIONS OR COMPONENTS Any new camshaft installation must use new lifters Even near new lifters which have been operated on a different cam lobe for even a few minutes can destroy the cam lobe of the new cam Valve springs must be properly matched to the camshaft Valve springs that coil bind due to the increased lift of a new cam will damage the cam lobes and or bend pushrods Springs with excessive seat pressure will destroy a cam lobe on initial startup If your springs exceed 125 lbs of seat pressure or if you are running dual springs you must remove the inner spring or damper or replace with a lighter spring approximately 100 Ibs of seat pressure for the initial break in period Failure to use new lifters and the proper valve springs will void any consideration of warranty High ratio rocker arms should also be avoided during the initial break in period Ratios higher than 1 5 1 increase the load at the cam lifter interface much
4. dings and write the number down This is your valve to piston clearance Rotate the engine to 15 degrees before TDC again take a measurement compress until contact with piston and take another measurement Compare and note readings Continue this process stopping every 5 degrees from 20 degrees before TDC to 20 degrees after TDC Repeat for the intake valve Minimum required piston to valve clearance is 100 on the intake valves and 120 on the exhaust valves When all checks are complete remove rocker arms pushrods and lifters 10 Now is the time to install the appropriate valve springs for the initial break in If your original valve springs have sufficient travel for the camshaft being installed see step 4 but have a lower seat pressure than the recommended springs they can be re installed for the initial 1 hour break in period The lower valve spring pressure will help the cam and lifters seat and establish a good wear pattern during the critical first 10 minutes of operation If your original valve springs do not have adequate travel for the lift of the new cam they must be replaced If the seat pressure of your new valve springs is higher than 100 lbs remove the inner spring or damper for the initial break in run Using the tools and procedures as outlined in step 4 install the appropriate valve springs on all valves note now is a good time to install new valve stem seals 11 With all of the valve springs installed lube and i
5. e engine does not idle below 1500 rpm Start engine and bring to break in rom 2000 rpm adjust idle speed screw as required Change rpm every few minutes to direct oil splash to different places inside the crankcase Maintain engine rpm within the range of 1500 to 2500 rpm for the first 30 minutes of operation If you note a strange noise or a leak or the engine is starting to overheat do not idle engine down shut it off and note run time Investigate and correct the situation then restart engine bring it back into the break in rpm range and start counting run time again If possible to safely do so perform a test drive during the next 30 minutes of break in Placing a load on the engine helps insure proper operating temperatures and distribution of lubricant Adjust idle speed down to 1500 rpm before test drive put transmission selector in neutral if sitting at a stop light do not allow engine to lug down below 1500 rpm Vary the engine speed frequently between 1500 and 2500 as you are driving After 1 hour of operation adjust idle speed to recommended setting 15 After the 1 hour break in period change the oil and filter Add another bottle of oil additive It is imperative that you change the filter as the moly particles and assembly contaminants will clog the filter element Remove the valve covers and inspect the valvetrain closely for any loose or damaged components If you were using break in valve springs or have removed the inner sprin
6. engine is equipped with exhaust valve rotators you should replace all of your retainers with those recommended for the new valve springs that you will be using Alternately you can temporarily install the intake valve retainer on the exhaust valve for checking purposes only After disconnecting compressed air source with checking springs installed slowly rotate the crankshaft approximately 90 degrees to move the piston away from TDC Using hand pressure push down on the valve stem until the under side of the retainer bottoms out on the top of either the valve guide or the valve seal see figure 2 Using your machinist rule again measure between the spring seat in the head and the retainer Subtract this dimension from the spring installed height dimension the resultant difference must be greater than the valve lift listed on your cam card Check both valves EXAMPLE Measured valve spring installed height 1 750 RETAINER RETAINER Measured height interference to retainer 1 200 CLEARANCE CLEARANGE Total obtainable valve travel 550 Safety margin for thermal expansion 060 Available valve travel 490 In this example if the max lift of your cam is 485 you have the necessary clearance to run this cam without issue If however you would install 1 6 1 ratio rocker arms instead of the stock 1 5 1 rockers it would increase the total lift to 517 and be dangerously close to binding the valvetrain and causing
7. er bores should be honed to the proper 0015 002 clearance Drain engine oil Clean all debris and traces of gasket from the lifter valley and timing cover area Flush with mineral spirits or brake cleaner use compressed air to blow dry When all fluid has drained from the oil pan pour a bottle of clean SAE 30 wt engine oil into the lifter valley from front to back when clean oil runs from the drain plug reinstall plug Pour a bottle of break in oil additive with zinc ZDDP such as our p n 282 159 over the lifter valley and then continue to service oil in this fashion to the full mark on the dipstick NOTE The lubricants recommended in these instructions are not interchangeable Each compound is formulated to perform a specific function Moly disulfide paste can plug small oil passages break in lube does not have the anti galling properties of moly assembly fluid does not have zinc for durability like break in lube Use each recommended lube in its specified location and application only 6 Remove the new cam and lifters from the package Make sure that it is the proper part for your application Inspect all lobes bearing surfaces and the distributor drive gear for damage that may have occurred in shipping It is a good idea to lightly burnish the drive gear with a wire brush to remove any sharp edges then wash the camshaft thoroughly with mineral spirits or brake cleaner and blow dry Temporarily install the camshaft timing gear to ac
8. g from your valve springs you can now replace them with the proper springs using the tools and procedures found in step 4 All valve springs must be installed at the manufacturers recommended installed height You may need a selection of different thickness valve spring shims or offset retainers or valve keepers in order to obtain the specified dimension see figure 5 If you do not need to replace the valve springs perform a valve adjustment as outlined in step 8 During the adjustment process pay special attention to note any major differences in valve lash or preload from before the break in run For example if you have installed a mechanical cam and adjusted the valve lash to 020 at installation but measure one valve at 060 clearance after the break in run remove that rocker arm pushrod and lifter and check closely for any bent or damaged components When all is deemed acceptable install valve covers and the job is complete The oil and filter should be changed again at 1000 miles of operation then resume the normal 2500 3000 mile oil change interval Continue to use a quality performance oil or ZDDP additive at each subsequent oil change Standard Taller Shorter Installed Height Installed Height Installed Height IMPORTANT DISCLAIMER In an effort to offer our customers the low prices quick service and great value Speedway Motors reserves the right to change suppliers specifications colors prices materials Each of the pre
9. like a stiff valve spring which leads to premature wear We recommend the use of stock rocker arm ratios for break in You may also choose to use low ratio rocker arms such as our 1 3 1 ratio rockers for break in Another current trend in performance engine building is the use of thinner oils and tighter clearances of the crankshaft bearings and connecting rod side clearance When you add lifter galley oil restrictors crankshaft scrapers and windage trays you greatly reduce the amount of oil being whipped around inside the crankcase The cam lobe lifter interface is lubed only by the oil splashing off of the rotating crank assembly during operation Reducing this oil splash can have an adverse effect on the durability of the camshaft Street cars with near stock oiling systems should be OK however track cars with modified oiling systems may find it beneficial to use special lifters with a pressure oiling hole in the contact face of the lifter We carry these premium lifters for Chevy p n 282 80016 and small block Ford p n 282 81716 and recommend that they be used in all applications with high valve spring rates or aggressive profiles on flat tappet mechanical cams Use of these lifters does not circumvent the necessity to use reduced valve spring pressures and or reduced rocker arm ratios for the initial break in period CAMSHAFT INSTALLATION 1 Prepare a clean work area and assemble the tools needed for the camshaft installation These i
10. nd that the cam sprocket is seated properly on the camshaft Torque bolts to proper spec per your service manual We recommend using locktite or a cam bolt locking plate to positively retain the bolts 8 Install lifters into the 1 cylinder positions Lube only the sides of the lifter body with assembly fluid coat the bottom of each lifter with moly paste Assemble the pushrods and rocker arms do not tighten rocker arm nuts at this time Turn the engine in the normal direction of rotation until the 1 exhaust rocker begins to move This assures that the intake lobe is on the base circle of the cam lobe see figure 4 Adjust the intake rocker arm nut to zero lash by spinning the intake pushrod with your fingers as you tighten the adjuster nut When you feel a slight resistance in rotating the pushrod you are at zero lash Continue to rotate the Incorrect engine in the normal direction of rotation until the intake valve is full open and then Correct Position starts to close When it is nearly closed stop and adjust the exhaust rocker arm to of the cam lobe zero lash and lifter for setting preload 9 Continue to rotate engine until the exhaust valve opens and then begins to close Stop at approximately 20 degrees before TDC of the overlap cycle Using your machinist rule or a dial indicator check the height of the valve spring retainer Push down on the rocker arm until the valve contacts the piston Note the reading Compare the two rea
11. nstall the lifters pushrods and rockers for the 1 cylinder as described in step 8 to achieve zero lash Apply a dab of moly lube to each end of the pushrod and the tip of the valve stem Apply assembly fluid to the rocker arm fulcrum For hydraulic lifter cams turn adjuster an additional turn from zero lash to properly preload the lifter plunger On engines with non adjustable valve trains consult the shop manual for proper shimming procedures or select a custom length pushrod that provides the recommended 020 040 lifter preload On solid lifter cams turn adjuster as required to obtain the valve lash listed on your cam card Non adjustable valve trains must be converted to an adjustable configuration when installing mechanical solid lifter cams Follow the same procedure to install the lifters pushrods and rocker arms on the remaining cylinders Double check everything 12 Initial lubrication is extremely important as the cam lobes can be wiped out in the first 10 minutes if the engine experiences a dry start Prior to installing the ignition distributor it is highly recommended that you pre lube the engine by using a primer shaft and electric drill This assures that the oil filter cam galley and lifters will have oil pressure immediately upon fire up Using a marking compound such as white out place a dot on each pushrod Crank the engine over with the starter 3 or 4 revolutions as you are priming the oil system Watch the val
12. nstructions are generalized due to the wide variety of current production engines and are not intended to cover all aspects of every camshaft installation We suggest that you use the appropriate automotive shop manual for your engine vehicle to help determine which items must be removed from the engine in order to gain access to the camshaft lifters timing chain rocker arms and valve springs 2 Disassemble engine as required Once the timing chain is exposed rotate crankshaft to line up the timing marks This will position engine at Top Dead Center of the 1 cylinder Remove the cam sprocket timing chain and cam retainer plate if so equipped Temporarily reinstall the cam sprocket to act as a handle and remove all lifters Carefully roll and slide cam out of engine using caution not to nick or damage the cam bearings 3 Now is the time to inspect all of the old camshaft and valvetrain related components The first factor to consider is the general condition of the engine As a new performance camshaft can increase power by up to 20 and expand the rev limit by 2000 rpm it stands to reason that the engine must be in top notch mechanical shape As the cam will have more lift and a faster opening rate excessive wear in the valve guides or a wear step in the valve stem can cause immediate catastrophic damage such as bent pushrods broken rocker arms and damaged camshaft lobes Check the pushrods rocker arms and rocker studs for excessive wea
13. r delivery to insure all the parts that you ordered were received Please read the invoice Double check all packing materials small items may be wrapped inside with these products Shortages may occur from damage to the box so save all packing materials Inspect the box for holes that would allow parts to fall out If you are missing any item s be sure to check your invoice for back orders or canceled items before calling the customer service department If Speedway has to split a shipment into multiple boxes packages may be delivered on different days You need to contact the customer service department within 5 days of delivery to assure the prompt replacement Speedway Motors assumes no liability after this period REFUSALS All refused COD customers will be billed a 15 restocking charge plus freight to and from the destination If you have questions please contact Speedway s customer service department WARRANTY CLAIMS If an item has a manufacturer s warranty as being free from defects we will exchange only If the item has been used and you are requesting warranty work this may take up to 30 days as warranty work is done by the manufacturer NOT Speedway Motors If you have any questions please contact customer service RETURNS Speedway wants you to be satisfied with your purchase If within 30 days after you receive your shipment you are not satisfied you may return the item for refund or exchange All exchanged or returned merchandise mu
14. r or damage If the engine has accumulated several thousand street miles the distributor drive gear must be closely inspected for wear as a worn gear will quickly destroy the gear on the camshaft Likewise the timing chain and gears must be replaced as a stretched timing chain will cause cam timing variations and subsequent ignition timing fluxuation NOTE If you are installing a replacement OEM style timing chain and gear set it is highly recommended that you properly degree the new camshaft Many OEM timing sets retarded camshaft timing for emission compliance which greatly detracts from the performance potential of your new camshaft Most aftermarket performance timing sets maintain proper camshaft phasing so it isn t absolutely necessary to degree the cam in order for the engine to run efficiently However to assure maximum performance we recommend that you degree your camshaft to verify that it is phased per manufacturers recommendations To properly degree the cam refer to the instructions provided by the degree wheel manufacturer NOTE A variety of special tools are required for the following steps Consult your shop manual for specifics or contact the Speedway Tech Department for assistance The number one factor in premature camshaft failure is due to the use of incorrect valve springs The following step is very important to the life of your new camshaft follow it closely Many OEM valve springs do not have sufficient travel to accommoda
15. st be in original factory condition with no modifications or alterations Returned merchandise must include all packaging materials warranty cards manuals and accessories If the items being returned need to be repackaged there will be a re packing charge Re pack the item in a sturdy box and include a copy of your invoice and complete the form on the back of the invoice You must ship orders back PRE PAID WE DO NOT ACCEPT COD SHIPMENTS All exchanges need to have reshipping charges included Items that are returned after 30 days are subject to 15 restocking charges All fiberglass returned will have 15 restocking charge No returns on electrical parts video tapes and books Absolutely no returns on special order or close out merchandise FREE CATALOGS Speedway Motors offers FREE catalogs for Race Street Sprint and Midget Sport Compact and Pedal Car restoration Some items are not legal for sale or use in California on pollution controlled motor vehicles These items are legal in California for racing vehicles only which may never be used upon a highway __ ee ID Q Speedway Motors Inc P O Box 81906 PEE OWAV Lincoln NE 68501 402 323 3200 is www speedwaymotors com Speedway Motors Inc 2006
16. t as a handle Use one of the new lifters coated lightly with engine oil and check the fitment in each lifter bore of the block Make sure that lifter fits freely in the bore with no sticking or binding Hydraulic lifters do not need to be pumped up prior to installation 7 Install the crank gear of your new timing set onto the crank snout using the proper tool Rotate the crankshaft back to TDC of the 1 cylinder Apply a moly disulfide paste lube such as our p n 450 R4 to each lobe of the cam including the fuel pump eccentric if applicable and distributor drive gear It is important to coat the lobes completely yet not excessively Do not get moly paste on the camshaft bearing journals Coat the rear bearing journal of the camshaft with assembly lube such as our p n 915 4040 Carefully slide the camshaft into the engine lubing each bearing journal as it slides into the block Take your time be careful not to scar the cam cam bearings or wipe the lube off of the cam lobes Once seated turn the cam until the timing mark lines up properly with the crank gear Remove temporarily installed cam gear Install camshaft retaining plate if so equipped and torque bolts to factory specs Install the new cam gear or sprocket and timing chain If installing an aftermarket timing set that includes thrust washers or bearings follow the installation instructions of the timing set manufacturer Make certain that the timing marks are properly aligned a
17. te the increased lift of your new performance cam If they are not replaced with the recommended valve springs and retainers immediate engine damage will result 4 Remove the valve springs from the 1 cylinder in accordance with the procedures outlined in your service manual this will involve rotating the engine by hand to TDC of the 1 cylinder inserting a compressed air fitting into the spark plug hole and using an on the engine valve spring compressor such as our p n 910 81130 to remove the springs Whenever the valve springs are removed stretch a rubber band across the exposed stems of the two valves or rocker studs to keep them from dropping into the cylinder when the air source is disconnected Using a valve spring height mic such as our p n 910 81125 measure the installed height of your existing valve springs compare this dimension to those listed in the spring requirements of your cam card If you do not have a valve spring height mic you can use a 6 machinist rule Install a pair of lightweight valve height checking springs like our p n 910 81129 and temporarily reinstall the valve spring retainer and keepers Using the machinist rule measure spring height from the spring seat of the cylinder head to the lower edge of the retainer see figure 1 NOTE Many smog era heads were factory equipped with exhaust valve rotators These rotators require shorter valvesprings and add additional weight to the valve train If your
18. vetrain closely as you are cranking for any obvious misalignment or binding Note the white dots on the pushrods to make sure that the lifters and pushrods are rotating as the engine is cranked Correct any noted deficiencies 13 Re assemble the engine in accordance with your shop manual Pay particular attention when installing the distributor so that the engine starts quickly without excessive cranking The following procedure is simple and effective Rotate the crankshaft in the normal direction of rotation until the 1 cylinder is coming up on TDC of the compression stroke both valves closed Align the timing mark on the crank balancer at the recommended initial timing setting approximately 10 degrees before TDC Install the distributor making sure that it engages the oil pump drive properly and is correctly seated it may be necessary to pull the distributor housing and turn the oil pump drive slightly by hand in order to engage the distributor shaft With the distributor properly installed and the hold down clamp left slightly loose rotate the distributor housing until the rotor is aligned with the 1 contact in the distributor cap Tighten hold down clamp 14 Make certain that the fuel system is primed Make sure that radiator is full and coolant hoses are properly connected Once the engine has been started you can not idle it down to make any adjustments or corrections Turn the idle speed screw clockwise 1 2 to 1 turn to assure that th
19. vious items is subject to change without notice Speedway is not responsible for any typographical errors or misinterpretations Quantities are limited on some items WARRANTY DISCLAIMER The purchaser understands and recognizes that racing parts specialized street rod equipment and all parts and services sold by Speedway Motors Inc are exposed to many and varied conditions due to the manner in which they are installed and used Speedway Motors Inc makes no warranties either express or implied including any warranty of merchantability or fitness for a particular purpose other than those contained in its current catalog with respect to the goods identified on the face of the invoice There is no warranty expressed or implied as to whether the goods sold hereby will protect purchaser or ultimate user of such goods from injury or death Speedway Motors assumes no liability after this period DAMAGE CLAIMS Always inspect your package upon delivery Inspect all packages in the presence of the delivery driver The driver must note any damage Ask the driver the Carriers procedures for handling damage claims You must hold the original box packing material and damaged merchandise for inspection or the carrier will not honor the claim Notify Speedway Motors customer service department for instructions on returning damaged goods Speedway is not responsible if no notification is given within 5 days of receipt SHORTAGES Always check the contents of you
Download Pdf Manuals
Related Search