MODEL : LK-P20B
Contents
1. Reliability TPH 50km Battery Continuous printing for 90min Standby for 24hours Communications standard Serial RS 232C USB Bluetooth Class2 Battery Charger input AC100 240V 50 6 Hz output 8 4V 1200 mA Battery Charger Battery type Li ion output 7 4V 1900mAh Charging time 2 Time WXDXH mm 96 X 136 X 58 WXDXH 3 7X5 3X2 2 Temperature 5 40 C 10 50 C Humidity 35 95 e Preventing Overheating To prevent the motor from overheating continuous driving of the printer should be 15 m or less in print length Set the pause time for 30 seconds or more after driving the printer 6 Setting up the software Please refer to the programming manual included in CD Certification FCC Information This device complies with part 15 of the FCC Results Operation is subject to the following two conditions 1 This Device may not cause harmful interface and 2 This device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for CLASS B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when he equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if2. not installed and used in accordance with the instuctions may cause harmful interference o radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by uming the equipment off and on the user is encouraged to try correct the interference by one or more of the following measures 11 Reorient or relocate the receiving antenna 12 Increase the separation between the equipment and receiver 13 Connect the equipment into an outlet on a circuit different from that to which receiver is connected 14 Consult the dealer or experienced radio TV technician for help A WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment 25 A CAUTION Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit
3. 30 seconds after continuous printing 1 5 meter 3 12 MSR usage Insert and swipe the card in the direction of the arrow as shown in the picture 3 13 IC CARD usage Insert the card in the direction of the arrow as shown in the picture This product can communicate with other devices via Bluetooth communication and cable 4 1 Bluetooth Connection 1 The Printer can be connected to devices equipped with Bluetooth communication capacity PDAs PCs etc 2 Use the Bluetooth connection function supported by the device to connect to the printer NOTE Refer to the Bluetooth Manual for more details on connection 4 2 Interface Cable Connection 1 Connect USB or Serial cable into the cable connector on the printer NOTE Use the cable offered by the manufacturer USB Serial 2 Connect the interface cable into the USB or Serial port of the device PDA PC etc 5 1 Specification Printing Method Direct Thermal Printing Speed 80mm sec Resolution 203 DPI X 203 DPI Character ALPHA NUMERIC Character Extension Character Barcode EAN 8 EAN 13 Code39 ITF UPC A Codabar Code93 Code128 PDF417 2D Emulation ESC POS Driver Window CE 4 2 amp 5 0 Window Mobile 5 0 Sensor Paper End Sensor Paper paper type Thermal Paper width 58mm thickness 650 External Diameter Max 48mm Internal Diameter 12 5mm 0 5mm
4. All specifications are subject to change without notice Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronics equipment For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Table of Contents 1 Unpacking 3 2 Product overview 4 3 Usage and Installation 5 3 1 Control panel usage 5 3 2 Battery Installation 6 3 3 Charging battery 7 3 4 Battery charger usage Optional 8 3 5 Usage of Cigar Jack for charging Optional 9 3 6 Battery removal 10 3 7 Belt Clip usage 11 3 8 Loading the media 12 3 9 Loading the media Optional 13 3 10 Leather case usage Optional 14 3 11 Self Test 15 3 12 MSR usage Optional 17 3 13 IC CARD usage Optional 18 Peripherals Connection 19 4 1 Bluetooth Connection 19 4 2 Interface Cable Connection 20 5 Specification 21 6 Setting up the software 23 Serial Cable Quick Manual Strap Belt Buckle Printer case 3 YG D X NS USB Shelded Cabl
5. e Cigar jack charger Roll paper Battery recharger MSR Slot Optional Power switch Paper feed Optional 4 LL DC Power Belt clip hole 3 1 Control panel usage Power Error This button is used to turn the printer on and off When the printer is off press this button for approximately 3 seconds and it will turn on the power When you press this button in a state that the printer is on the printer will turn off Paper output can be done manually by pressing this button Additionally self testing and Hexadecimal Dumping can be processed 1 Refer to 3 10 for self test information 2 Refer to the service manual regarding Hexadecimal Dumping 1 If the Batt LED are Lit the battery is fully charged 2 If you can hear beeping sound and LED light is turned off it means that the battery is at the lowest level 3 If the battery is not charged at all the printer turns off automatically If the red light is turned on it means there is no paper roll or the paper cover is open 3 2 Battery Installation 1 Align battery hook as shown in the picture 2 Push the battery into the printer until it locks in place NOTE As the battery is not charged at the time of your purchase charge the battery prior to using the printer Battery charger or Cradle can be used to charge 3 3 Charging battery 1 Be sure that the printer is turned off 2 Af
6. ight direction Pull a short length of paper out of the printer and close the cover 3 9 Shoulder Strap Usage Optional Insert the strap into the hook on the printer Place the end of strap into the hook of shoulder strap After pulling out the end of strap tightly put it into the clip to be fastened Fasten the strap in the opposite side with the sample way 3 10 Leather case usage Close the Velcro and stick the cover Fasten to the belt by using the clip at the rear of the leather case 3 11 Self Test Turn off the power pressing the While you are pressing the FEED power button for approximately button press the power button 3 minutes NOTE 1 To print ASCII pattern additionally press the Feed button once more 2 After printing ASCII pattern the self test will be finished automatically 3 If the Feed button is not pressed to print ASCII pattern self test will be finished automatically after 30 seconds The printout is produced When the printer is installed initially or when you face a problem you can run the self test and check the information about Control Circuit Mechanism Print Quality ROM Version After checking with self test and no issues are found you can examine other devices and software This function is working independent of devices and software Motor protection from being overheated The motor should be stopped and cooled about more than
7. ter open the DC JACK cover insert DC JACK into the printer 3 Plug the power code to electrical outlet NOTE 1 Unless the exclusive charger is used provided by the manufacturer the printer can be damaged and the manufacturer is not liable for the consequential damage 2 Before removing the battery make sure that power is turned off 3 Printer does not work in the status of being connected with charger only 4 The battery should be installed to operate printer 5 While charging do not turn on the power 6 Do not operate the print while charging the battery 7 Do not connect the charger while the printer is operated 3 4 Battery charger usage Optional 1 Insert the battery into the battery holder as shown above 2 Connect the DC JACK to the power electrical outlet 3 Once the charging is completed remove the battery from the holder 3 5 1 The status of lamp in charging Charging Lamp NOTE In the case the battery is not fixed properly in the holder the red lamp will be blinking Then extract and reinsert the battery 3 5 Usage of Cigar Jack for charging Connect the car cigar JACK charger into the printer or battery holder 3 6 Battery removal Remove the battery as shown 3 7 Belt Clip usage Tighten the screw with driver as shown 3 8 Loading the media XS Place the paper roll as shown Press the cover open button and open Make sure the paper is placed in r
Download Pdf Manuals
Related Search