Service Manual for SR-XFeeder
Contents
1. Y er Ue Installation and INTRODUCTION The Everpure SR X Scale Reduction Feeders are designed to efficiently dispense scale inhibiting products into foodservice water filtration systems There are two versions One SR X is intended for cold water applications such as ice machines and replaces the previous Everpure IMF Feeder The other SR X w Deliming Kit is intended for hot water applications such as steamers and replaces the previous Everpure AR X Feeder THE SR X FEEDER EV9798 45 INCLUDES e Aclear bowl plastic housing e An opaque head with integral mounting bracket e An Everpure SS IMF ScaleStick cartridge containing HydroBlend a unique specially blended compound that inhibits mineral scale deposits and provides corrosion protection for water fed equipment e Two SS IMF Spacers adapts SS IMF to 10 bowl e A sump wrench THE SR X FEEDER W DELIMING KIT EV9797 20 INCLUDES The same housing and head included in the SR X Feeder An Everpure SS 10 ScaleStick cartridge containing the HydroBlend compound A check valve with pipe nipple packed loose to prevent backflow in hot water applications One 2 2 Ib packet of Everpure ScaleKleen scale remover A dip tube to convert the SR X Feeder for use in introducing the ScaleKleen product A sump wrench NOTE The SR X and SR X w Deliming Kit Feeders are supplied with different versions of ScaleStick cartridges The SR X Feeder includes the SS IMF ScaleStick EV9799 32 whi2. 125 psi 8 6 bar 35 F 100 F 2 38 C essure Limit 20 21 22 kilograms of ScaleKleen have been introduced into the boiler chamber Proceed to step 11 With ScaleKleen material introduced into the boiler chamber and the inlet water turned on allow the steamer countertop or boiler base to come up to operating temperature and pressure and hold for one hour Thirty minutes into the de liming procedure turn on steam to cooking chamber s for one minute This will de lime the distribution lines small orifices and steam solenoid valves After one hour of de liming the steamer at operating temperature and pressure turn the steamer power switch off Manually blow down the steamer if it is not done automatically when the power is turned off Fill the boiler with fresh clean water and repeat blow down a second time to void the boiler chamber of any un dis solved loose scale Thoroughly rinse the cooking compartment s with cold water and wipe dry with a clean soft towel After the second blow down turn the steamer power switch off and turn off the water to the SR X Feeder Relieve system pressure by depressing the red button on the SR X head until all air is purged and water begins to escape Unscrew the bowl and remove the dip tube from the head BE SURE TO PLACE THE DIP TUBE IN A CONVENIENT LOCATION Install a new SS 10 cartridge into the head and thread the bowl back on
3. the SR X Feeder and install mounting screws 2 4 apart If installing the EV9797 20 SR X Feeder w Deliming Kit assemble the 3 4 check valve and pipe nipple provided loose onto the outlet of the feeder head 2 Un thread the head assembly from the bowl 3 Locate the ScaleStick cartridge in the carton and remove its shrink wrapping SR X Scale Reduction Feeder EV3114 49B FE05 10 IMPORTANT If installing an SR X Feeder using the SS IMF ScaleStick cartridge approx 7 length locate the two SS IMF Spacers in the bowl This is a short length approx 24 of ScaleStick cartridge bottom used to extend the length of the SS IMF cartridge so that it fits securely into the 10 SR X bowl Insert the spacer into the bottom of the SS IMF cartridge and proceed to the next step Insert the ScaleStick black O band seal at the top onto the outlet stub on the bottom of the feeder head Check to be sure the o ring on the bowl is clean and sufficiently lubricated and apply a high quality food grade silicone lubricant if more is needed Thread the bowl onto the feeder head with ScaleStick by hand while aligning the ScaleStick with the guide seat in the bottom of the bowl Snug the bowl with the sump wrench EV3112 41 Connect the inlet water line to the inlet fitting connection on the SR X Feeder head Connect the SR X outlet to the piping tubing leading to the equipment being treated Continue with installation of the rest of t
4. W EVERPURE DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE TO THE EXTENT REQUIRED BY LAW ANY SUCH IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE PERIOD SPECIFIED ABOVE FOR THE ENTIRE WATER TREATMENT UNIT As a manufacturer we do not know the characteristics of your water supply or the purpose for which you are purchasing this product The quality of water supplies may vary seasonally or over a period of time and your water usage rate may vary as well Water characteristics can also differ considerably if this product is moved to a new location For these reasons we assume no liability for the determination of the proper equipment necessary to meet your requirements and we do not authorize others to assume such obligations for us Further we assume no liability and extend no warranties express or implied for the use of this product with a non potable water source or a water source which does not meet the conditions for use described in the owner s guide or performance data sheet for this product OUR OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT AT EVERPURE S DISCRETION OF THE FAILED PARTS OF THE WATER TREATMENT UNIT AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT INDIRECT INCIDENTAL CONSEQUENTIAL SPECIAL GENERAL OR OTHER DAMAGES Some states do not allow the exclusion of implied warranties or limitations on how long an implied warrant
5. ch is shorter approx 7 in height and contains less of the HydroBlend material than the SS 10 ScaleStick EV9799 02 approx 10 in height included with the SR X Feeder w Deliming Kit The SS IMF cartridge requires two 2 1 4 spacer included with EV9798 45 which adapts it for use in the new longer SR X bowls SR X SCALE REDUCTION FEEDER INSTALLATION SR X Feeders are provided in three forms 1 As stand alone feeders where their functions may be added to existing water consuming foodservice equipment installations 2 As integral elements of standard Everpure water filter systems 3 As add on elements to standard Everpure water filter systems The SR X Feeders incorporate provisions for retrofitting onto new style Everpure multi cartridge multi function filter systems to provide scale control as needed Adaptation is accomplished by adding an optional post feeder bracket to an existing system Detailed installation instructions come with the post feeder brackets Before starting the installation be sure to shut off both power and water to the equipment being served For servicing convenience a manual shut off valve should be installed in the water line ahead of the feeder IMPORTANT Always use a NSF approved pipe dope or Teflon tape at all thread connections CONNECT TO INLET FEED WATER MAKE UP LINES ONLY DO NOT CONNECT TO ICE MACHINE CONDENSER OR STEAMER CONDENSATE COOLING LINES 1 Select a suitable location for mounting
6. f FIVE YEARS The entire system excluding replaceable elements This is for material amp workmanship not filter or water treatment cartridge life The unit must be used in operating conditions that conform to Everpure s recommended design guidelines This warranty will not apply if the unit has been modified repaired or altered by someone not authorized by Everpure If a part described above is found defective within the specified period you should notify Everpure technical service at the phone number listed below Any part found defective within the terms of this warranty will be repaired or replaced at Everpure s discretion by your local dealer or Everpure technical service You pay only freight from our factory and local dealer charges Any repaired or replaced warranty item will be incorporated under the original warranty terms of the existing system We are not responsible for damage caused by accident fire flood freezing Act of God misuse misapplication neglect oxidizing agents such as chlorine ozone chloramines and other related components alteration installation or operation contrary to our printed instructions or by the use of accessories or components which do not meet Everpure s specifications Refer to the specifications section in the Installation and Operating manual for approved application parameters Our product performance specifications are furnished with each water treatment unit TO THE EXTENT PERMITTED BY LA
7. he filter system if the SR X Feeder is being added on Turn on water to the SR X Feeder and momentarily depress the red button on the head to purge air from the unit CARTRIDGE CHANGE INSTRUCTIONS iP The SR X Feeder bowls and ScaleStick cartridges are transparent permitting continuous monitoring of product level When the product level in the ScaleStick cartridge drops to within 1 2 from the bottom the cartridge should be replaced Turn off inlet water to the feeder and momentarily depress the red button on the head to relieve pressure Un thread the bowl from the head empty water from the bowl and remove the used cartridge IMPORTANT If changing cartridges in an SR X Feeder using the SS IMF ScaleStick cartridge approx 7 length remove the SS IMF Spacer from the bottom of the used cartridge and set it aside Do not discard the spacer Proceed to the next step Clean the bowl with a mild solution of unscented dishwashing detergent DO NOT use soap strong or scented detergents chemical solvents or abrasives Remove the shrink wrapping from the new ScaleStick cartridge IMPORTANT If replacing an SS IMF ScaleStick cartridge into an SR X Feeder reuse the SS IMF Spacer set aside from Step 4 Insert the spacer into the bottom of the new SS IMF cartridge and proceed to the next step Note If the SS IMF Spacer is missing or misplaced a replacement spacer may be ordered Alternatively you may cut the bottom 2 1 4 from
8. ridge Dispose of the exhausted cartridge in normal trash and empty any remaining water from the bowl Locate the SR X dip tube and insert the tube O ring first into the center port of the head as far as it will go Open a one kilogram 2 2Ib package of ScaleKleen and empty it into the bowl Wipe off any excess ScaleKleen material which may be on the bowl threads or O ring Thread the bowl back into the SR X head hand tight only NOTE The dip tube end may become packed with ScaleKleen This is normal and will not affect the de liming procedure Turn on the inlet water to the SR X system Turn on the power to the steamer NOTE This action will quickly introduce the ScaleKleen material directly into the boiler chamber If you are de liming a countertop steamer proceed to step 11 If you are de liming a boiler base unit monitor the ScaleKleen level in bowl When the level drops to 1 quickly turn off the inlet water Now relieve pressure and unscrew the bowl from the head Add another kilogram of ScaleKleen to the bowl and reintroduce the material into the boiler Repeat this procedure until four 4 SPECIFICATIONS Overall Dimensions Shipping Weights 12 44 H x 5 16 D 2 Ibs SR X 4 5 Ibs SR X w Deliming Kit Inlet outlet Connections 3 4 FNPT Materials of construction Head polypropylene Clear bowl transparent plastic Service Flow Rate Pr Temperature Limits 0 5 6 0 gpm 1 9 22 5 Ipm
9. the used ScaleStick and use that portion as the spacer Insert the cartridge black O band seal at the top onto the outlet stub on the bottom of the feeder head Check to be sure the O ring on the bowl is clean and sufficiently lubricated and apply a high quality food grade silicone lubricant if more is needed Thread the bowl onto the feeder head with ScaleStick by hand while aligning the ScaleStick with the guide seat in the bottom of the bowl Snug the bowl with the sump wrench EV3112 41 Turn on water to the SR X Feeder and momentarily depress the red button on the head to purge air from the unit INLET 3 4 FNPT gt ff 3 4 FNPT OUTLET STEAMER DE LIMING These instructions apply to the Everpure SR X Feeder as well as to the previous AR X Feeder Use only Everpure ScaleKleen scale remover product Other harsh acids may damage bowl material and clog system orifices Use a one kilogram 2 2 Ib package to de lime most countertop steamers Use four kilogram 2 2 Ib packages to de lime most boiler based steamers Turn off the power switch on the steamer Blow down the steamer Blow down is done automatically on some steamers when power is turned off Manually blow down the steamer if this is not done automatically Turn off inlet water to the SR X system Depress the red button on the head to relieve system pressure Unscrew the clear bowl and remove the used cart
10. to the head Snug the bowl with the sump wrench EV3112 41 Turn on the inlet water Relieve any trapped air in the bow by depressing the red button on the SR X head until all air is purged and water starts escaping Turn the steamer power switch on The steamer is now ready to be placed back into service Be sure to order additional SS 10 replacement cartridges ScaleKleen and carbon filter cartridges to maintain future worry free operation of your steamer REPLACEMENT PARTS Contact your local Everpure dealer for filter cartridges or system replacement parts Description Part Number Head EV3112 37 O ring EV3112 40 10 bowl clear EV3112 39 Sump wrench EV3112 41 SS IMF 7 ScaleStick 12 pack for SR X EV9799 32 SS IMF spacer EV3114 69 SS 10 ScaleStick 12 pack for SR X w Deliming Kit EV9799 02 Dip tube for SR X Deliming Kit EV3080 40 3 4 outlet check valve for SR X w Deliming Kit EV3114 50 LIMITED WARRANTY COMMERCIAL WATER TREATMENT EQUIPMENT You have just purchased one of the finest water treatment units made As an expression of our confidence in Everpure products this product is warranted against defects in material and workmanship to the original end user when installed in accordance with Everpure specifications The warranty period commences from the date of purchase and is administered as follows For a period of ONE YEAR Replaceable elements i e filter amp water treatment cartridges For a period o
11. y lasts so the above limitation may not apply to you Similarly some states do not allow the exclusion of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Consult your telephone directory for your local independently operated Everpure dealer or write Everpure for warranty and service information EV EeVe For sales replacement components and service contact your Everpure dealer or Technical Service Everpure LLC 1040 Muirfield Drive e Hanover Park Illinois 60133 800 323 7873 800 942 1153 In Europe Toekomstlaan 30 B 2200 Herentals Belguim Www everpure com In Japan Hashimoto MN Bldg 7F 3 25 1 Hashimoto Sagamihara Shi e Kanagawa 229 1103 Japan Printed in U S A EV3114 49B FE05
Download Pdf Manuals
Related Search