SERVICE MANUAL
Contents
1. K1W120 shown as example pivot ring reused decorative ring reused Figure 2 1 Replacement head 3 4 accessory 2 ASSEMBLY AND INSTALLATION 1 Remove display from K1 head assembly Set aside hardware for reuse 2 Remove button head cap screw spacers and washers to disassemble head from K1 mounting arm See Figure 1 NOTE Set aside decorative ring and pivot ring for reuse K1W120 shown set aside for reuse Figure 1 3 Use 5 16 18 x 2 3 4 button head cap screw D two thin steel washers H plastic washer J thick spacer C pivot pin G removed pivot ring removed decorative ring 5 16 18 lock nut F and socket bit B to secure replacement head assembly A to Kontour mount See Figure 2 NOTE Use 3 4 wrench to hold socket bit B in position while button head cap screw D is tightened Service Manual For recessed mounting hole installation Place four spacers on top of mounting holes on back of display See Figure 5 Using Phillips screwdriver carefully install four M4x25mm screws through corresponding holes on faceplate spacers and into the mounting holes on the display See Figure 5 for recessed mounting holes o quick release faceplate M4x25mm x4 spacers x 45 Figure 5 4 Position display with faceplate attached above mount See Figure 62. Pivot Adjustment 3 Adjust pivot position as desired See Figure 7 4 Use3 16 hex key K to adjust pivot point tension screws to change pivot adjustment tension See Figure 7 Rotational tension pivot point tension tension Figure 7 Rotational Adjustment NOTE Optional Rotational adjustment may be locked by installing rotational locking screw E into back of faceplate See Figure 8 Figure 8 5 The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor See Figure 7 6 Use 3 16 hex key K to adjust rotational adjustment screw to adjust rotational tension See Figure 7 Service Manual Service Manual Service Manual 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 lt lt lt lt TU USA International i CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002743 0 2015 Milestone AV Technologies www chiefmfg com 05 15
3. 5 Slide faceplate onto mounting head until quick release tab clicks into place See Figure 6 Figure 6 Display Installation 1 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 3 Figure 3 2 Carefully place display face down on protective surface NOTE Use display mounting hardware included with K1 Series mount to attach display to new faceplate 3 Connect faceplate to display For flush mounting hole installation Using Phillips screwdriver carefully install four M4x14mm screws through corresponding holes on faceplate and into the mounting holes on the display See Figure 4 for flush mounting holes quick release faceplate o M4x14mm x4 Figure 4 Display Removal WARNING Only remove display from mount when the display can be lifted up from the mount DO NOT remove display unless the display is in the upright position See Figure 9 1 Make sure display is in the upright position 2 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 9 quick release tab Figure 9 Service Manual Adjustments Pitch Adjustment 1 Adjust pitch to desired tilt position See Figure 7 2 Adjust pitch tension screw to change the adjustment tension See Figure 7
4. SERVICE MANUAL Kontour Series Head Replacement Kit i CHIEF Our Mounts Your Vision Service Manual damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located attached to the replacement tilt head accessory up to and including the display does not exceed the weight limit listed for the mount to which it is attached Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS INTERFACE AO TATION RANGE MOUNTING PATTERN COMPATIBILITY 100X100 15115 Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes
5. no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Kontour are registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury DIMENSIONS 6 Service Manual TOOLS PARTS FOR INSTALLATION u 3 16 included 1 8 included A 1 Socket de de 1 l ick spacer D 1 E 1 F 1 5 16 18 2 3 4 10 24 x 1 4 5116 18 _H 2 J 1 Thin steel washer Plastic washer G 1 Pivot pin 4 K 4 L 1 1 1 8 3 16
Download Pdf Manuals
Related Search