Home

Form #5386

1. blue side seat elements to the opening in the carpet underneath the seat near the air vent Figure 8 Route the inputs for the driver red and passenger blue side switches to the area in front of the shift knob and set aside Figure 9 Route and connect the two ground terminal rings to ground point I3 below the HVAC controls Figure 10 Remove left door step kick panel and lower instrument panel Route the inputs for the driver and passenger power red and blue wires to the center console beneath the radio and left behind the driver knee panel to the driver side junction box Figure 11 Disconnect connector 3C from the junction box and release the locking tabs on the connector Insert the red wire driver side power into Pin 4 of connector 3C Insert the blue wire passenger side power into Pin 13 of connector 3C Replace the locking tabs on the connector and reconnect the connector to the Junction Box Figure 12a Page 4 of 8 DUAL SEAT HEATER KIT Figure 12a 2012 TOYOTA CAMRY LE SE XLE Section II Installation 9 NOTE XLE models with SmartKey may be pre wired for the factory seat heater Figure 12b In this case remove the RED and VIOLET wires from Pin 4 and Pin 13 respectively and tape them to the harness as shown in Figure 12c ve vs Figure 13 E Camry LE S i 10 Secure the harnesses with wire ties to the factory harness in center console and behind the driv
2. Aaa Form 5386 Rev B 07 11 2014 Page 2 of 8 TOYOTA CAMRY LE SE XLE 2012 DUAL SEAT HEATER KIT Section II Installation Install Heating Elements cont d gt 9 Make sure vehicle floor pan is clear and carefully re locate seat into vehicle gt 10 Ensure all connectors under seat have been properly connected and secured with wire ties and that nothing will be damaged upon seat VW movement 11 Install seat bolts and torque per service manual 12 Reconnect battery cable s Torque 10mm bolt to 48 inch pounds Re enter any theft V deterrent information if applicable 13 Note If the passenger seat cushion has a Seat Occupant Sensor for Airbag Deployment it must be re calibrated per guidelines in the Factory Repair Manual 14 Place the Seat Heater Operation Instructions in the glove box Form 5386 Rev B 07 11 2014 Page 3 of 8 TOYOTA CAMRY LE SE XLE Section II Installation 2012 DUAL SEAT HEATER KIT Install Main Harnesses V gt l l J Form 5386 Rev B 07 11 2014 1 Remove the shift knob bezel cup holders and center floor console Install the driver red tape and passenger blue tape main power harnesses near the factory floor harness as shown Figure 7 NOTE For XLE models take care to route the relays and main harnesses beneath the HVAC ducting at the right of the shifter Route the outputs for the driver red and passenger
3. ED will turn red The heat will be noticeable within 3 minutes The heating time can vary according to the type of seat cover material and kind of clothing coat that is being worn The heating must be switch to the Low setting in order to avoid overheating when the desired temperature has been reached Switch in Low setting The LED will turn green The heating time can vary according to the type of seat cover material and kind of clothing coat that is being worn Troubleshooting The heating does not function although it is switched on The LED is not illuminated Check the fuse and change if necessary The LED in not illuminated although the heating is functioning and switched on The LED in the switch is defective The heating does not function although it is switched on The LED is on The temperature of the seat cover could be too high due to high interior temperature The thermostat in the seat heating unit is connected Wait until the seat cover s temperature has fallen and try again The fuse burns out repeatedly Verify the fuse rating is correct 10 amps Form 5386 Rev B 07 11 2014 Page 7 of 8 TOYOTA CAMRY LE SE XLE 2012 SEAT HEATER KIT Section III Functional Verifications Notes Form 5386 Rev B 07 11 2014 Page 8 of 8
4. TOYOTA CAMRY LE SE XLE Section I Pre Installation Check 2012 DUAL SEAT HEATER KIT Kit Part Number 250 1897 Kit Contents Quantity Reqd Cushion Element Additional Items Required For Installation Item _ Quantity Reqd Switch Cutout Template Vehicle Protection Blankets Conflicts Note Factory leather and cloth Recommended Tools Quantity Reqd Description Form 5386 Rev B 07 11 2014 General Applicability Recommended Sequence of Application Item Accessory S Wris J Ge Legend STOP Damage to the vehicle may occur Do not proceed until process has been complied with OPERATOR SAFETY Use caution to avoid risk of injury CRITICAL PROCESS Proceed with caution to ensure a quality installation m GENERAL PROCESS This highlights specific processes to ensure a quality installation EDIOOLS amp EQUIPMENT This calls out the specific tools and equipment required for this process VEHICLE PROTECTION This calls out for protection of vehicle required for this process Page 1 of 8 TOYOTA CAMRY LE SE XLE 2012 DUAL SEAT HEATER KIT Section II Installation Pre Installation Suggestions Gp 1 Disconnect the negative battery cable and wait o for 3 minutes before beginning installation to gt avoid unintended air bag deployment Note and record any anti theft radio codes prior to disconnecting Figure 1 2 If vehicle is in Electronics work area pro
5. ceed to step 1 page 4 If vehicle is in Leather shop proceed to next section Install Heating Elements Install Heating Elements a 1 Remove seats from vehicle per vehicle s service manual and place on a clean work surface 2 Remove seat covers per vehicle s service manual V 3 Caution The heating elements must be installed wrinkle free ign gt 4 Obtain the back heating element Remove the ee t Wl protective layer from the element s double sided tape and place it onto the seat back foam roughly centered on the foam from side to side with the top of the element just below the transverse listing tie bar trench Figure 2 cutouts gt 5 Route the element wiring harness down to the Route bottom of the seat back inboard of the hinge k N harnesses EN cover and under the seat r here gt 6 Repeat the process above for the seat cushion laying the heating element transversely such that it does not interfere with the horizontal listings Figure 3 gt 7 Secure the seat harnesses to the tie down bar and run down the side listing to the back of the seat then down Re attach seat covers Figures 4 5 harnesses ce ik together 8 Replace the driver and passenger seats into the and route vehicle Connect the seat element connectors Pea G here to the main harnesses Secure the harness with wire ties and allow adequate slack to prevent damage during seat adjustment ioe gt iN Figure 6
6. er knee panel Figures 11 13 Camry LE SE shown Page 5 of 8 Form 5386 Rev B 07 11 2014 TOYOTA CAMRY LE SE XLE 2012 Section II Installation Install Switches V 1 Use the Camry drill fixture to make 3 8 pilot ED holes in trim piece Enlarge hole with a 13 16 21mm hole saw Figures 14a 15 CA NOTE Camry LE SE share one fixture Camry XLE is a separate fixture gt 2 Push the switch harness through hole and snap the switch firmly into place Figure 16 3 Connect the switches to the switch inputs on the main harnesses in the center console Connect left driver switch to the 4 pin connector marked with the red tape and connect the right passenger switch to the 4 pin connector marked with the blue tape 4 Use the Seat Heater Harness Tester to validate switch and harness function and orientation 5 Reinstall all trim panels in the reverse order of removal 6 Reconnect battery cable s Torque 10mm bolt to 48 inch pounds Re enter any theft deterrent information if applicable NIS _ gt 13 16 Drill 2 Holes Figure 15 Form 5386 Rev B 07 11 2014 DUAL SEAT HEATER KIT Camry LE SE Figure 14a Page 6 of 8 TOYOTA CAMRY LE SE XLE Section III Functional Verifications Check 2012 SEAT HEATER KIT Look For Verify Function and Heat IGN ON Check switch in both High and Low position Switch in High setting The L

Form #5386

Contents

Download Pdf Manuals

Related Search

Related Contents