Dell Inspiron B130 Service Manual - MI
Contents
1. 2 Tighten the ZIF socket by turning the cam screw clockwise to secure the microprocessor module to the system board 3 Wipe the thermal grease off of the microprocessor thermal cooling assembly with a clean paper towel 4 Replace the microprocessor thermal cooling assembly See Installing the Microprocessor Thermal Cooling Assembly 5 Update the BIOS using a flash BIOS update program CD See Flashing the BIOS From a CD Back to Contents Page Back to Contents Page Display Assembly Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Display Assembly Removing the Display Bezel Removing the Display Panel Installing the Display Panel Removing the Display Assembly A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the hinge cover See Removing the Hinge Cover 3 Remove the keyboard See Removing the Keyboard 4 Pull straight up on the pull tab that is attached to the display feed flex cable to disconnect the cable from the system board 5 Disconnect the antenna cable 6 Close the display 7 Turn the computer upside down with the bac2. 1 To replace the keyboard connect the keyboard connector to the system board 2 Place the tabs along the front edge of the keyboard into the palm rest and lay the keyboard down on the palmrest 3 Replace the two screws at the top of the keyboard 4 Replace the hinge cover See Replacing the Hinge Cover 1 keyboard 2 system board connector Back to Contents Page Back to Contents Page Modem Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Modem Replacing the Modem Removing the Modem A CAUTION Before you begin the following procedure see the safety instructions in the Product I nformation Guide NOTICE To avoid damaging the system board you must remove the main battery before you begin working inside the computer See Replacing the Battery A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface i Follow the instructions in Before Working Inside Your Computer 2 Remove the hinge cover See Removing the Hinge Cover 3 Remove the optical drive See Removing the Optical Drive 4 Remove the keyboard See Removing the Keyboard 5 Remove the coin cell battery See Removing the Coin Cell Battery 6 Remove the display assembly See Removing the Display Assembly 7 Remove the palm rest See Removing the Pa
3. 5 Install the drivers and utilities for your computer Returning a Hard Drive to Dell Return your old hard drive to Dell in its original or comparable foam packaging Otherwise the hard drive may be damaged in transit A N ia N aa jN o 1 foam packaging 2 hard drive Back to Contents Page Back to Contents Page Hinge Dell Inspiron 1300 B120 Bi30 Service Manual Removing the Hinge Cover Replacing the Hinge Cover A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface NOTICE The hinge cover is fragile and can be damaged if extreme force is used Be careful when removing the hinge cover Removing the Hinge Cover 1 Follow the instructions in Before Working Inside Your Computer 2 Turn the computer right side up and then open the display all the way 180 degrees so that it rests on your work surface NOTICE To avoid damaging the hinge cover do not lift the cover on both sides simultaneously 3 Insert a scribe in the indent to lift the hinge cover on the right side oO e e a 4 Ease the hinge cover up moving from right to left and remove it Replacing the Hinge Cover 1 Insert the left ed
4. mounting bracket Hold a component such as a processor by its edges not by its pins NOTICE Only a certified service technician should perform repairs on your computer Damage due to servicing that is not authorized by Dell is not covered by your warranty NOTICE When you disconnect a cable pull on its connector or on its strain relief loop not on the cable itself Some cables have a connector with locking tabs if you are disconnecting this type of cable press in on the locking tabs before you disconnect the cable As you pull connectors apart keep them evenly aligned to avoid bending any connector pins Also before you connect a cable ensure that both connectors are correctly oriented and aligned NOTICE To avoid damaging the computer perform the following steps before you begin working inside the computer Ensure that the work surface is flat and clean to prevent the computer cover from being scratched Turn off your computer See Turning Off Your Computer NOTICE To disconnect a network cable first unplug the cable from your computer and then unplug it from the network wall jack 3 Disconnect any telephone network and USB cables from the computer 4 Disconnect your computer and all attached devices from their electrical outlets 5 Turn over the computer NOTICE To avoid damaging the system board you must remove the main battery before you service the computer 6 Remove the battery a Slide the battery b
5. See Removing the Modem 13 Remove the speakers connector See Removing the Speakers 14 Remove the system board See Removing the System Board 15 Disconnect the the fan power cable from the system board 16 Turn the system board over and remove the four M2 5 x 5 mm screws holding the metal plate in place i fan assembly M2 5 x 5 mm screws 4 17 Remove the plate and lift the system board off the fan assembly Installing the Cooling Fan 1 Position the system board over the fan assembly aligning the screw holes in the system board with those in the fan assembly 2 Place the metal plate over the holes in the system board and replace the four M2 5 x 5 mm screws 3 Turn the system board over and connect the fan connector to the system board Back to Contents Page Back to Contents Page Hard Drive Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Hard Drive Installing the Hard Drive Removing the Hard Drive A CAUTION If you remove the hard drive from the computer when the drive is hot do not touch the metal housing of the hard drive A CAUTION Before you begin any of the procedures in this section follow the safety instructions in the Product Information Guide NOTICE To prevent data loss turn off your computer before removing the hard drive Do not remove the hard drive while the computer is on in standby mode or in hibernate mode NOTICE Hard drives are extremely fragile even a sl
6. avoid damaging the system board you must remove the main battery before you begin working inside the computer 1 Follow the instructions in Before Working Inside Your Computer 2 Turn the computer over loosen the captive screws on the memory module Mini PCI cover and then remove the cover fo h captive screws 3 Ff 3 Ifa Mini PCI card is not already installed go to step 1 If you are replacing a Mini PCI card remove the existing card a Disconnect the antenna cable from the Mini PCI card 1 antenna cable b Release the Mini PCI card by spreading the metal securing tabs until the card pops up slightly c Lift the Mini PCI card out of its connector NOTICE The connectors are keyed to ensure correct insertion If you feel resistance check the connectors and realign the card 1 Mini PCI card 2 metal securing tabs 2 Installing the Mini PCI Card 1 Install the replacement Mini PCI card NOTICE To avoid damaging the Mini PCI card make sure the antenna cable is not under the card when you press the card into place a Align the Mini PCI card with the connector at a 45 degree angle and press the Mini PCI card into the connector until it clicks 1 Mnipci cara f2 metal securing tas J b Connect the antenna cable to the Mini PCI card Make sure the cable snaps onto the primary connector on the Mini PCI card 2 Replace the memory module Mini PCI cover and tighten the screws
7. from the top cover screw covers display bumpers 6 M2 5 x 5 mm screws 6 display bezel a topcover CT o S Removing the Display Panel A CAUTION Before performing the following procedures read the safety instructions in the Product I nformation Guide CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the display assembly See Removing the Display Assembly 3 Remove the display bezel See Removing the Display Bezel 4 Remove the four M2 x 3 mm screws from each side of the display panel 5 Lift the display panel out of the top cover See ee display panel M2 x 3 mm screws 8 6 Press in both sides of the top flex cable connector and pull the top flex cable connector away from the display connector pull tab on bottom flex cable connector top flex cable connector 4ldisplay connector fo 7 Use the pull tab to disconnect the bottom flex cable connector from the inverter connector Installing the Display Panel 1 Connect the top flex cable connector to the display panel connector 2 Connect the bottom flex cable connector to the inverter connector 3 Lay the display panel into the top cover 4 Replace the eight M2 x 3 mm screws that s
8. modem from the telephone wall jack A CAUTION Using an incompatible battery may increase the risk of fire or explosion Replace the battery only with a compatible battery purchased from Dell The battery is designed to work with your Dell computer Do not use a battery from other computers with your computer To remove the battery 1 If the computer is connected to a docking device docked undock it See the documentation that came with your docking device for instructions 2 Ensure that the computer is turned off 3 Turn over the computer 4 Slide the battery bay latch release lock on the bottom of the computer away from the battery 5 Slide and hold the battery bay latch release and then remove the battery from the bay 1 battery 2 battery bay latch release 3 battery bay latch release lock To replace the battery follow the removal procedure in reverse order Back to Contents Page Back to Contents Page Before You Begin Dell Inspiron 1300 B120 B130 Service Manual Recommended Tools Turning Off Your Computer Before Working Inside Your Computer Computer Orientation Screw Identification This chapter provides procedures for removing and installing the components in your computer Unless otherwise noted each procedure assumes that the following conditions exist You have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer You have read the safety informa
9. 5 Remove the Mini PCI card See Removing the Mini PCI Card 6 Remove the microprocessor thermal cooling assembly See Removing the Microprocessor Thermal Cooling Assembly 7 Remove the microprocessor See Removing the Microprocessor Module 8 Remove the hinge cover See Removing the Hinge Cover 9 Remove the keyboard See Removing the Keyboard 10 Remove the display assembly See Removing the Display Assembly 11 Remove the palm rest See Removing the Palm Rest 12 Remove the modem See Removing the Modem 13 Remove the speakers connector See Removing the Speakers 14 Remove the five M2 5 x 5 mm system board screws and lift the system board out and away from the base plastics 1 M2 5 x 5 mm screws 5 Installing the System Board 1 Insert the video connector on the replacement system board through the side of the base plastics 2 Replace the five M2 5 x 5 mm screws that secure the system board to the base plastics 3 Reconnect the speakers See Installing the Speakers 4 Replace the modem removed from the system board See Replacing the Modem 5 Replace the palm rest See Removing the Palm Rest and follow the procedure in reverse order 6 Replace the display assembly See Removing the Display Assembly and follow the procedure in reverse order 7 Replace the keyboard See Replacing the Keyboard 8 Replace the microprocessor See Installing the Microprocessor Module NOTICE Before you replace the microprocessor th
10. Dell Inspiron 1300 B120 B130 Service Manual Before You Begin Hinge System Components Battery Memory Optical Drive and Mini PCI Card Hard Drive Keyboard Display Assembly Palm Rest Modem Coin Cell Battery Microprocessor Thermal Cooling Assembly Microprocessor Module Speakers System Board Antenna Fan Flashing the BIOS Base Plastics Pinout Assignments for I O Connectors Model PP21L Notes Notices and Cautions K NOTE A NOTE indicates important information that helps you make better use of your computer NOTI CE A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem _ CAUTION A CAUTION indicates a potential for property damage personal injury or death Information in this document is subject to change without notice 2005 Dell Inc All rights reserved Reproduction in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell the DELL logo and Inspiron are trademarks of Dell Inc Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Dell Inc disclaims any proprietary interest in trademarks and trade names other than its own Back to Contents Page Antenna Dell Inspiron 1300 B120 B1i30 Service Manual Replacing the Antenna Replacing the Antenna A CAUTION Before
11. NOTICE If the cover is difficult to close remove the module and reinstall it Forcing the cover to close may damage your computer 3 Insert the battery into the battery bay or connect the AC adapter to your computer and an electrical outlet 4 Turn on the computer Back to Contents Page
12. Remove the cable from the guides and lift the coin cell battery from the computer Replacing the Coin Cell Battery 1 Connect the cable to the system board by pushing it into the connector 2 Route the cable through the channel and press the coin cell battery into place Back to Contents Page Back to Contents Page Microprocessor Module Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Microprocessor Module Installing the Microprocessor Module Removing the Microprocessor Module A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface NOTICE Press and hold the microprocessor down by applying slight pressure to the center of the microprocessor while turning the cam screw to prevent intermittent contact between the cam screw and microprocessor NOTICE To avoid damage to the microprocessor hold the screwdriver so that it is perpendicular to the microprocessor when turning the cam screw 1 Follow the instructions in Before Working Inside Your Computer 2 Turn over the computer 3 Remove the microprocessor thermal cooling assembly See Removing the Microprocessor Thermal Cooling Assembly NOTICE W
13. aiming the marks and names or their products Dell Inc disclaims any proprietary interest in trademarks and trade names other than its own Back to Contents Page Back to Contents Page Memory Optical Drive and Mini PCI Card Dell Inspiron 1300 B120 B1i30 Service Manual Memory Optical Drive Mini PCI Card Memory Removing the Memory Module _ CAUTION Before working inside your Dell computer read the safety instructions in the Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface K NOTE Memory modules purchased from Dell are covered under your computer warranty 1 Follow the instructions in Before Working Inside Your Computer 2 Ground yourself by touching one of the metal connectors on the back of the computer E NOTE If you leave the area ground yourself again when you return to the computer 3 Turn the computer over loosen the captive screws on the memory module Mini PCI cover and then remove the cover 1 captive screws 3 NOTI CE To prevent damage to the memory module connector do not use tools to spread the memory module securing clips 4 If you are replacing a memory module remove the existing module a Use your fingertips to carefully spread apart the securing clips on
14. ay latch release lock on the bottom of the computer away from the battery b Slide and hold the battery bay latch release and then remove the battery from the bay battery bay latch release battery bay latch release lock 7 Press the power button to ground the system board 8 Remove any installed ExpressCards from the ExpressCard slot Computer Orientation 1 1 front 2 left 3 back 4 right Screw Identification When you are removing and replacing components print this section as a tool to lay out and keep track of the screws The printout provides the number of screws and their sizes H H M2x 3mm M3x3mm M25x4mm M25x5mm M25x6Emm M25x8mm Ee PE pe e p p H M M es Optical Drive Fan Module Display Assembly to Computer Base 1 each 4 each haa M2 5x 8 mm M2 5 x 5mm 4 each M2 5 x 8mm Modem to Display Bezel Display Panel System Board 6 each 8 each jana kje H H M2 5 x 5 mm M2 x 3 mm M2 x 3 mm 2 each Top of Palm Rest to Base Plastic to Hard Drive Carrier to Computer Base Palm Rest From Bottom Hard Drive 5 each of M2 5 x 5 mm 10 each 2 each 2 each of M2 x 3 mm M2 5 x 8mm M2 5 x 5 mm M2 x 3mm Speakers to System Board to Keyboard to Palm Rest Base Plastics Base Plastics 2 each 1 for left speaker 2 for right 5 each system board speaker 3 total H H M2 5 x 5 mm M2 5x 5mm Back to Contents Page Back to Contents Pag
15. e Flashing the BIOS Dell Inspiron 1300 B120 B130 Service Manual Flashing the BIOS From a CD Flashing the BIOS From the Hard Drive If a BIOS update program CD is provided with the new system board flash the BIOS from the CD If you do not have a BIOS update program CD flash the BIOS from the hard drive Flashing the BIOS From a CD 1 Ensure that the AC adapter is plugged in and that the main battery is installed properly K NOTE If you use a BIOS update program CD to flash the BIOS set up the computer to boot from a CD before inserting the CD 2 Insert the BIOS update program CD and restart the computer Follow the instructions that appear on the screen The computer continues to boot and updates the new BIOS When the flash update is complete the computer will automatically reboot 3 Press lt F2 gt during POST to enter the system setup program 4 Press lt Alt gt and lt F gt to reset the computer defaults 5 Press lt Esc gt select Save changes and reboot and press lt Enter gt to save configuration changes 6 Remove the flash BIOS update program CD from the drive and restart the computer Flashing the BIOS From the Hard Drive 1 Ensure that the AC adapter is plugged in the main battery is properly installed and a network cable is attached 2 Turn on the computer 3 Locate the latest BIOS update file for your computer at support dell com 4 Click Download Now to download the file 5 If t
16. each end of the memory module connector until the module pops up b Remove the module from the connector Replacing the Memory Module 1 Ground yourself and install the new memory module a Align the notch in the module edge connector with the tab in the connector slot Slide the module firmly into the slot at a 45 degree angle and rotate the module down until it clicks into place If you do not feel the click remove b the module and reinstall it 1 memory slot notch 2 memory slot tab 2 Replace the memory module Mini PCI cover and tighten the screws NOTICE If the cover is difficult to close remove the module and reinstall it Forcing the cover to close may damage your computer 3 Insert the battery into the battery bay or connect the AC adapter to your computer and an electrical outlet 4 Turn on the computer As the computer boots it detects the additional memory and automatically updates the system configuration information To confirm the amount of memory installed in the computer click the Start button click Help and Support and then click Computer I nformation Optical Drive Removing the Optical Drive CAUTION Before working inside your Dell computer read the safety instructions in the Product I nformation Guide NOTICE To prevent damage to devices store them in a safe dry place when they are not installed in the computer Avoid pressing down on them or placing heavy objects on t
17. ecure the display panel to the top cover 5 Route the display feed flex cable so that it rests in the notch located in the bottom edge of the top cover 6 Replace the display bezel Back to Contents Page Back to Contents Page Fan Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Cooling Fan Installing the Cooling Fan Removing the Cooling Fan A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the hard drive See Removing the Hard Drive 3 Remove the optical drive See Removing the Optical Drive 4 Remove the memory module See Removing the Memory Module 5 Remove the Mini PCI card See Removing the Mini PCI Card 6 Remove the microprocessor thermal cooling assembly See Removing the Microprocessor Thermal Cooling Assembly 7 Remove the microprocessor See Removing the Microprocessor Module 8 Remove the hinge cover See Removing the Hinge Cover 9 Remove the keyboard See Removing the Keyboard 10 Remove the display assembly See Removing the Display Assembly 11 Remove the palm rest See Removing the Palm Rest 12 Remove the modem
18. ee Removing the Coin Cell Battery 6 Remove the display assembly See Removing the Display Assembly 7 Turn the computer upside down and remove the ten M2 5 x 8 mm screws from the bottom of the computer 8 Turn the computer top side up and remove the five M2 5 x 5 mm screws from the top of the palm rest and the remaining two M2 5 x 3 mm screws from near the power button and the activity LEDs Disconnect the touch pad connector from the system board by pulling the release tabs forward away from the connector and removing the cable 1 suspend switch 2 touch pad ribbon cable release tabs 3 touch pad ribbon connector 2 cable 10 Disconnect the suspend switch connector from the system board NOTICE Carefully separate the palm rest from the base plastics to avoid damage to the palm rest 11 Starting at the back center of the palm rest use your fingers to separate the palm rest from the base plastics by lifting the inside edge of the palm rest Back to Contents Page Back to Contents Page Pinout Assignments for I O Connectors Dell Inspiron 1300 B120 B130 Service Manual USB Connector Video Connector USB Connector ar Sat a Pin Signal xo Back to Contents Page Back to Contents Page Speakers Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Speakers Installing the Speakers Removing the Speakers A CAUTION Before pe
19. ermal cooling assembly wipe the thermal grease off of the assembly with a clean paper towel Squeeze the contents of the thermal grease packet provided with the kit onto the microprocessor thermal cooling assembly 9 Replace the microprocessor thermal cooling assembly See Installing the Microprocessor Thermal Cooling Assembly 10 Replace the Mini PCI card that you removed from the old system board See Installing the Mini PCI Card 11 Replace the memory module that you removed from the old system board See Replacing the Memory Module 12 Replace the optical drive See Installing the Optical Drive 13 Replace the hard drive See Installing the Hard Drive 14 Insert the battery into the battery bay See Replacing the Battery 15 Connect the AC adapter to the computer and to an electrical outlet NOTICE Before turning on the computer replace all screws and ensure that no stray screws remain inside the computer Failure to do so may result in damage to the computer K NOTE After replacing the system board enter the computer Service Tag into the BIOS of the replacement system board 16 Turn on the computer 17 Insert the CD that accompanied the replacement system board into the appropriate drive Follow the instructions on the screen Back to Contents Page Back to Contents Page System Components Dell Inspiron 1300 B120 B1i30 Service Manual A CAUTION Only a certified service technician should perform repairs
20. ews 4 ER Installing the Microprocessor Thermal Cooling Assembly NOTICE Before you install the replacement microprocessor thermal cooling assembly remove the mylar that covers the thermal grease on the assembly Lower the microprocessor thermal cooling assembly into place on top of the microprocessor aligning the numbered screws labeled 1 through 4 with the numbers on the fan assembly and the arrow on the pull strap pointing toward the outside edge of the system board Tighten the four captive screws labeled 1 through 4 in consecutive order Replace the thermal cooling microprocessor cover and tighten the screws Back to Contents Page Back to Contents Page Dell Inspiron 1300 B120 B130 Service Manual K NOTE A NOTE indicates important information that helps you make better use of your computer NOTI CE A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem _ CAUTION A CAUTION indicates a potential for property damage personal injury or death Information in this document is subject to change without notice 2005 Dell Inc All rights reserved Reproduction in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell the DELL logo and Inspiron are trademarks of Dell Inc Other trademarks and trade names may be used in this document to refer to either the entities cl
21. ge of the cover into place 2 Press from left to right until the cover snaps into place 3 Close the display and turn the computer upside down 4 Replace the battery See Replacing the Battery Back to Contents Page Back to Contents Page Keyboard Dell Inspiron 1300 B120 Bi30 Service Manual Removing the Keyboard Replacing the Keyboard Removing the Keyboard _ CAUTION Before working inside your Dell computer read the safety instructions in your Product Information Guide CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the hinge cover See Removing the Hinge Cover 3 Remove the two screws at the top of the keyboard NOTICE The keycaps on the keyboard are fragile easily dislodged and time consuming to replace Be careful when removing and handling the keyboard 4 Lift up the keyboard and hold it up and slightly forward to allow access to the keyboard connector on the system board 5 Lift the keyboard connector and slide out the keyboard cable Replacing the Keyboard NOTICE To avoid scratching the palm rest when replacing the keyboard hook the tabs along the front edge of the keyboard into the palm rest and then secure the keyboard in place
22. he Export Compliance Disclaimer window appears click Yes Accept this Agreement The File Download window appears 6 Click Save this program to disk and then click OK The Save In window appears 7 Click the down arrow to view the Save In menu select Desktop and then click Save The file downloads to your desktop 8 Click Close if the Download Complete window appears The file icon appears on your desktop and is titled the same as the downloaded BIOS update file 9 Double click the file icon on the desktop and follow the instructions on the screen Back to Contents Page Back to Contents Page Coin Cell Battery Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Coin Cell Battery Replacing the Coin Cell Battery Removing the Coin Cell Battery A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface m Follow the instructions in Before Working Inside Your Computer 2 Remove the hinge cover See Removing the Hinge Cover 3 Remove the keyboard See Removing the Keyboard 4 Locate the coin cell battery and disconnect the cable from the system board connector by pulling toward the coin cell battery 5
23. hen removing the microprocessor module pull the module straight up Be careful not to bend the pins on the microprocessor module 4 To loosen the ZIF socket use a small flat blade screwdriver and rotate the ZIF socket cam screw counterclockwise until it comes to the cam stop The ZIF socket cam screw secures the microprocessor to the system board Take note of the arrow on the ZIF socket cam screw 1 ZIF socket cam screw 2 ZIF socket 3 pin 1 corner of microprocessor 5 Use a microprocessor extraction tool to remove the microprocessor module Installing the Microprocessor Module NOTICE Ensure that the cam lock is in the fully open position before seating the microprocessor module Seating the microprocessor module properly in the ZIF socket does not require force NOTICE A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and ZIF socket 1 Align the pin 1 corner of the microprocessor module so that it points to the triangle on the system board and insert the microprocessor module into the ZIF socket When the microprocessor module is correctly seated all four corners are aligned at the same height If one or more corners of the module are higher than the others the module is not seated correctly NOTICE Hold the microprocessor down while turning the cam screw to prevent intermittent contact between the cam screw and microprocessor
24. ight bump can damage the drive K NOTE Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell K NOTE If you are installing a hard drive from a source other than Dell you need to install an operating system drivers and utilities on the new hard drive To replace the hard drive in the hard drive bay 1 Follow the instructions in Before Working Inside Your Computer 2 Turn the computer over and loosen the two captive screws in the hard drive cover fe fowesrews a S d O NOTI CE When the hard drive is not in the computer store it in protective antistatic packaging See Protecting Against Electrostatic Discharge in the Product Information Guide 3 Lift the cover off the computer and set it aside 4 Slide the hard drive carrier away from the screw holes and then use the tab to lift the hard drive straight up to remove it from the computer Installing the Hard Drive 1 Remove the new drive from its packaging Save the original packaging for storing or shipping the hard drive NOTICE Use firm and even pressure to slide the drive into place If you use excessive force you may damage the connector 2 Seat the new hard drive into the bay and then slide it into the connector by sliding it toward the screw holes until it is fully seated 3 Replace the cover and tighten the screws 4 Install the operating system for your computer using the Operating System CD
25. k of the computer facing you 8 From the bottom of the computer remove the two M2 5 x 8 mm screws labeled D 9 From the back of the computer remove the two M2 5 x 8 mm screws labeled D 10 Turn the computer right side up and open the display 11 Carefully remove the antenna cable and the display cables from their routing guides FN ee e soey ae purs O N N NOTI CE Be careful not to damage the display switch when removing the display 12 Lift the display assembly out of the computer base Removing the Display Bezel A CAUTION Before performing the following procedures read the safety instructions in the Product I nformation Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the display assembly See Removing the Display Assembly 3 Usea plastic scribe to pry the six screw covers display bumpers out of the screw holes on the front of the bezel 4 Remove the six M2 5 x 5 mm screws from the front of the bezel NOTICE Carefully separate the bezel from the top cover to avoid damage to the bezel 5 Starting at the bottom of the display panel use your fingers to separate the bezel from the top cover and lift the inside edge of the bezel away
26. lastics NOTICE Ensure that the speaker cables are under or between their routing clips K NOTE The speakers face out in the base plastics holders K NOTE The right speaker cable is longer than the left speaker cable 2 Route the speaker cables under or between their routing clips 3 Replace the three M2 x 3 mm screws 4 Connect the speaker connector to the system board Back to Contents Page Back to Contents Page System Board Dell Inspiron 1300 B120 Bi30 Service Manual Removing the System Board Installing the System Board Removing the System Board A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface The system board s BIOS chip contains the Service Tag which is also visible on a barcode label on the bottom of the computer The replacement kit for the system board includes a CD that provides a utility for transferring the Service Tag to the replacement system board 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the hard drive See Removing the Hard Drive 3 Remove the optical drive See Removing the Optical Drive 4 Remove the memory module See Removing the Memory Module
27. lm Rest 8 Remove the two M2 x 3 mm screws that attach the modem to the system board 9 Pull up on the pull tab to disconnect the modem from the connector on the system board NOTICE Do not disconnect the modem cable from the system board 10 Disconnect the modem cable from the modem Replacing the Modem 1 Connect the modem cable to the modem NOTICE Ensure that the modem cable is routed correctly when you replace the modem 2 Connect the modem to the system board Align the connector on the bottom of the modem with the modem connector on the system board and press down on the right side of the modem 3 Replace the two M2 x 3 mm screws Back to Contents Page Back to Contents Page Palm Rest Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Palm Rest Removing the Palm Rest A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the hinge cover See Removing the Hinge Cover 3 Remove the optical drive See Removing the Optical Drive 4 Remove the keyboard See Removing the Keyboard 5 Remove the coin cell battery S
28. nual A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the hard drive See Removing the Hard Drive 3 Remove the optical drive See Removing the Optical Drive 4 Remove the memory module See Removing the Memory Module 5 Remove the Mini PCI card See Removing the Mini PCI Card 6 Remove the microprocessor thermal cooling assembly See Removing the Microprocessor Thermal Cooling Assembly 7 Remove the microprocessor See Removing the Microprocessor Module 8 Remove the hinge cover See Removing the Hinge Cover 9 Remove the keyboard See Removing the Keyboard 10 Remove the display assembly See Removing the Display Assembly 11 Remove the palm rest See Removing the Palm Rest 12 Remove the modem See Removing the Modem 13 Remove the speakers connector See Removing the Speakers 14 Remove the system board See Removing the System Board Back to Contents Page Back to Contents Page Battery Dell Inspiron 1300 B120 B1i30 Service Manual Replacing the Battery Replacing the Battery A CAUTION Before performing these procedures disconnect the
29. on your computer Damage due to servicing that is not authorized by Dell is not covered by your warranty NOTICE Unless otherwise noted each procedure in this document assumes that a part can be replaced by performing the removal procedure in reverse order igo o _ 3 5 8 10 11 12 E 14 15 16 17 18 antenna cable Back to Contents Page Back to Contents Page Microprocessor Thermal Cooling Assembly Dell Inspiron 1300 B120 B1i30 Service Manual Removing the Microprocessor Thermal Cooling Assembly Installing the Microprocessor Thermal Cooling Assembly Removing the Microprocessor Thermal Cooling Assembly A CAUTION Before performing the following procedures read the safety instructions in the Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Turn over the computer 3 Loosen the captive screw in the thermal cooling microprocessor cover and remove the cover 4 Loosen in consecutive order the four captive screws labeled 1 through 4 in the thermal cooling assembly 5 Lift the thermal cooling assembly out of the computer by pulling straight up on the pull strap thermal cooling assembly pull strap captive scr
30. op of them NOTE If your computer shipped with a device security screw and the screw is not installed you can remove and install devices while the computer is running and connected to a docking device 1 If you want to remove the optical drive while the computer is turned on double click the Safely Remove Hardware icon on the taskbar click the device that you want to eject and click Stop Otherwise go to step 2 2 Close your display and turn the computer upside down 3 Use a Phillips screwdriver to remove the M2 5 x 8 mm screw from the indention labeled with a lock symbol a 4 Using a screwdriver or some other type of probe push the notch where the device security screw was removed toward the outside of the computer 5 Pull the device straight out of the media bay 1 CD DVD drive 2 drive removal slot 3 M2 5 x 8 mm screw labeled A Installing the Optical Drive 1 Slide the new drive into the bay until it snaps securely into place 2 Replace the M2 5 x 8 mm screw 3 Turn the computer right side up and open the display 4 The operating system automatically recognizes the device If necessary enter your password to unlock your computer Mini PCI Card Removing the Mini PCI Card If you ordered a Mini PCI card with your computer the card is already installed A CAUTION Before you begin any of the procedures in this section follow the safety instructions in the Product Information Guide NOTICE To
31. performing the following procedures read the safety instructions in the Product Information Guide A CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the hard drive See Removing the Hard Drive 3 Remove the optical drive See Removing the Optical Drive 4 Remove the memory module See Removing the Memory Module 5 Remove the Mini PCI card See Removing the Mini PCI Card 6 Remove the microprocessor thermal cooling assembly See Removing the Microprocessor Thermal Cooling Assembly 7 Remove the microprocessor See Removing the Microprocessor Module 8 Remove the hinge cover See Removing the Hinge Cover 9 Remove the keyboard See Removing the Keyboard 10 Remove the display assembly See Removing the Display Assembly 11 Remove the palm rest See Removing the Palm Rest 12 Remove the modem See Removing the Modem 13 Remove the speakers connector See Removing the Speakers 14 Remove the system board See Removing the System Board 15 Remove the antenna cable from the guides 16 Replace the antenna cable securing it under the guides 1 antenna cable 2 guides Back to Contents Page Back to Contents Page Base Plastics Dell Inspiron 1300 B120 B1i30 Service Ma
32. rforming the following procedures read the safety instructions in the Product Information Guide CAUTION To prevent static damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface The speakers are located on the left and right front corners of the base plastics Take note of the speaker cable routing so that you can replace the cables properly under or between their routing clips 1 Follow the instructions in Before Working Inside Your Computer 2 Remove the hinge cover See Removing the Hinge Cover 3 Remove the optical drive See Removing the Optical Drive 4 Remove the keyboard See Removing the Keyboard 5 Remove the coin cell battery See Removing the Coin Cell Battery 6 Remove the palm rest See Removing the Palm Rest 7 Disconnect the speaker connector from the system board M2 5 x 3 mm screws 3 2 speaker connector NOTI CE Remove the speaker cables from their routing clips with care to avoid damaging the cables 8 Remove the speaker cables from under or between their routing clips NOTI CE Handle the speakers with care to avoid damaging them 9 Remove the three M2 x 3 mm screws from the speaker mounts 10 Remove the speakers by pulling them straight up and out of the base plastics I nstalling the Speakers 1 Slide the speakers down into the base p
33. tion in the Product Information Guide A component can be replaced by performing the removal procedure in reverse order Recommended Tools The procedures in this document may require the following tools Small flat blade screwdriver Phillips screwdriver Small plastic scribe Hex nut driver Flash BIOS update program floppy disk or CD Turning Off Your Computer NOTICE To avoid losing data save and close any open files and exit any open programs before you turn off your computer Shut down the operating system a Save and close any open files exit any open programs click the Start button and then click Turn Off Computer b Inthe Turn off computer window click Turn off The computer turns off after the operating system shutdown process finishes Ensure that the computer and any attached devices are turned off If your computer and attached devices do not automatically turn off when you shut down your operating system press and hold the power button for 4 seconds Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety A oO O gt CAUTION Before you begin any of the procedures in this section follow the safety instructions in the Product Information Guide CAUTION Handle components and cards with care Do not touch the components or contacts on a card Hold a card by its edges or by its metal
Download Pdf Manuals
Related Search