SERVICE MANUAL
Contents
1. BRACKET INSTALLATION amp CONSOLE SETUP 3 3 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LMM CONSOLE CONTINUED 19 Use the double sided tape to secure the dongle to the PCTV plastics Figure V If the system is wired skip this step 20 Plug the TV power wire coming up the console mast into the TV power wire installed in step 15 Both wires are labeled TV 21 Reinstall the console 22 Plug the side of the controller wire labeled TO CONSOLE into the C Safe port on the back of the console Figure W NOTE The TV port is next to the C Safe port and will not work for PCTV FIGURE V FIGURE W 23 Install the PCTV back cover Figure X 24 If the PCTV is going to be connected to the internet through an Ethernet Cable plug the Ethernet cable into the Ethernet port on the bottom of the treadmill Figure Y 25 Plug in the PCTV power wire into the base of the cardio Figure Y FIGURE X FIGURE Y 26 Enter Engineering Mode by pressing the INCLINE DOWN and SPEED DOWN keys at the same time and toggling to Engineering then press ENTER 27 Toggle to Audio Source and push ENTER Toggle to PCTV and push ENTER This will ensure the audio from the PCTV can be heard through the treadmill headphone jack 28 If the sound is too quiet or too loud toggle to Volume Control and push ENTER When the screen says Output Default push ENTER again The volume range can be adjusted 29 Press and hold the PAUSE or STO2. za j j mu FIGURE G FIGURE H 8 Mount the TV bracket to the console using 4 socket head screws sent with the TV bracket kit Figure 9 Plug the 4 pin black connector to the power wire coming up the console mast from the base of the unit Figure J FIGURE J FIGURE 10 Plug the side of the controller wire labeled To Console into the CSafe board mounted on the console back Figure K The wire goes into the PCTV port Also change switch SW1 to the top location for PCTV 11 Route the net and power cables through the console These wires are not plugged into the UCB but should be routed through the console to hide the wires The 8 amp 4 pin black connectors shouild stick out the bottom of the console along with the HR wiring Figure L 12 Connect one end of the coax cable to the board on the back cover using the adaptor sent with the TV kit Figure M oz IEE E bn LEETE FIGURE K FIGURE L FIGURE M 26 BRACKET INSTALLATION amp CONSOLE SETUP 3 4 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LAM CONSOLE CONTINUED 13 There should now be 4 wires sticking out the top of the console TV power wire net wire coax cable and controller wire Figure N 14 Re attach the console back to the front using the bottom 6 screws removed in Step 2 NOTE Be sure to route the wiring so that it is not pinched by the bracket or plastic when installing the top 2 screws Figure O The small
3. 10 Connect the TV bracket to the console mast using the 4 screws that were holding the logo in place in Step 7 Figure L FIGURE K FIGURE L 11 Insert the spring pin into the hole at the top of the TV bracket Figure M FIGURE M 12 Install the rabbit ears onto the TV bracket using the bolt nut and washers from the TV bracket kit Figure N NOTE Make sure that the rabbit ears are installed so that the spring pin is restricting the range of motion Figure O C F m 7 j FIGURE N FIGURE O 22 BRACKET INSTALLATION amp CONSOLE SETUP 3 3 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LMM CONSOLE CONTINUED 13 Mount the PCTV to the bracket using 4 screws shipped in the back of the TV Figure P 14 Run the coax cable from the TV bracket to the back of the PCTV and screw it in Figure Q FIGURE P FIGURE Q 15 Plug the power wire from the TV bracket into the back of the TV Figure R 16 Plug the side of the controller wire labeled TO TV into the port titled PCTV Figure S i i FIGURE R g FIGURE S 17 If the system is wired plug the net wire yellow from the TV bracket kit into the Net port in the back of the PCTV Figure T If the system is wireless skip this step 18 If the PCTV is wireless plug the wireless dongle into the USB port on the back of the PCTV Figure U If the system is wired skip this step FIGURE T E FIGURE U 23 24
4. C 3 Remove the back of the console and install the TV Mounting Bracket using the 4 screws and washers from the bracket kit Figure D 7 R i i i P i p 1 FIGURE C FIGURE D BRACKET INSTALLATION amp CONSOLE SETUP 3 1 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x TM LMM CONSOLE CONTINUED 4 Plug the TV power wire into the back of the TV Figure E 5 Plug the controller wire into the port titled PCTV Figure F KU FIGURE E FIGURE F 6 If the system is going to be wired plug the Net Wire from the TV Bracket kit into the Ethernet port in the back of the PCTV Figure G If the system is wireless skip this step FIGURE G 7 If the PCTV is wireless plug the wireless dongle into the USB port on the back of the PCTV Figure H and use the double sided tape to se cure the dongle to the PCTV plastics Figure I If the system is wired skip this step FIGURE H FIGURE 13 BRACKET INSTALLATION amp CONSOLE SETUP 3 1 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x TM LMM CONSOLE CONTINUED 8 Mount the front plate to the PCTV TV using 2 screws sent with the TV bracket kit Figure J 9 Install the PCTV to the TV Mounting Bracket using the 4 screws shipped in the back of the PCTV Figure K Make sure the tabs of the front plate slide behind the console faceplate to create a seamless look FIGURE J FIGURE K 10 Connect the console cable from Step 1 to th
5. Figure V FIGURE U FIGURE V 20 Enter into Engineering Mode by pressing INCLINE DOWN and SPEED DOWN keys at the same time and toggling to Engineering then press ENTER 21 Toggle to Audio Source then press ENTER Toggle to PCTV and push ENTER This will ensure the audio from the PCTV can be heard through the treadmill headphone jack 22 If the sound is too quiet or too loud toggle to Volume Control and push ENTER When the screen says Output Default push ENTER again The volume range can be adjusted 23 Press and hold the PAUSE or STOP key for 3 5 Seconds or press the EMERGENCY STOP to return to normal operation 24 A channel scan should be done using the instructions included in the TV owner s manual 19 20 BRACKET INSTALLATION amp CONSOLE SETUP 3 3 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LMM CONSOLE All Universal 5x consoles have a minimum software version to allow a PCTV See the minimum software version for this console in the table in Section 3 8 The software versions can be found in Manager Mode To enter Manager Mode press and hold ELEVATION and SPEED DOWN at the same time for 3 5 seconds Use the LEVEL keys to scroll to Manager Mode and press ENTER Then use the LEVEL keys to toggle to Software and hit ENTER This will display the current software versions Use the LEVEL keys to toggle through the versions to find the UCB software version Press and hold the PAUSE key to exit ASSEMBLY
6. S Video cable Check that audio console audio out cable is plugged into the console Note The audio cable has a 5V line that enables the S Video output from the treadmill Note The audio cable connector is next to the Ethernet cable connector Video present but audio is not present Loose or unplugged audio cable to console Check audio cable connection to console Note Audio cable is next to the Ethernet connector 2 Check audio settings in Engineering Mode 3 Contact Matrix Technical Support TV Audio Volume does not change from PCTV is a touch screen unit 1 Install the Target Heart Rate Overlay treadmill volume control buttons If a problem with a Netpulse compatible machine is seen follow the directions in this troubleshooting guide to solve the problem If the problem cannot be resolved call Netpulse at 877 NETPULSE 638 7857 59 60 TROUBLESHOOTING 6 4 TROUBLESHOOTING WORKOUT REPORTING ISSUES SYMPTOM CAUSE RESOLUTION No workout history generated There are several possible causes Refer to cardio machine product manual e C SAFE may not be enabled to ensure C SAFE is enabled e C SAFE cables may be loose or not Test the machine to see if workout properly installed statistics can be generated Contact Matrix Technical Support for further assistance 6 5 TROUBLESHOOTING TOUCH SCREEN ISSUES SYMPTOM CAUSE RESOLUTION Touch screen cursor does not line up with Touch screen requires cal
7. a Ae Eat eer FIGURE F 4 Use the on screen keys to enter a gender and date of birth Figure G This is used in some programs like Target Hear Rate Push NEXT 5 Enter a weight this can be changed as personal fitness goals are reached Figure H Push NEXT FIGURE G FIGURE H 6 Confirm the registration Figure I Push NEXT FIGURE 57 58 TROUBLESHOOTING 6 1 TROUBLESHOOTING GENERAL ISSUES SYMPTOM CAUSE RESOLUTION All units off Electricity is shut off 1 Check and restore power to all PCTV machines Users cannot sign in Affects all units Gateway or Internet service is not connected Check power and Cat 6 connections on the Netpulse Gateway in server room or electrical closet Restore as needed 2 Check power and connections to Internet Router reset Router remove power for 15 seconds then restore if no activity 3 Check PCTV machines again 4 If wired Check if GREEN LED is lit where Ethernet cable plugs into the console 5 If problem persists contact Matrix Technical Support One Unit No Power to screen Machine unplugged or failed power cable Reconnect power at outlet or PCTV machine Contact Matrix Technical Support One unit Can t sign on NOTE Check other Check all Internet connections between units for problem machine and Gateway Reboot unit Test unit to ensure it is working Contact Matrix Technical Support One unit Black screen Loose power c
8. are chosen touch NEXT to begin scanning eee TY CONFIGURATION Cheese Tuner Type Live Existing Configuration Analog Handa Angla Cable Digital Digital Cable Cicendasd Configuraiion Analog Cable mE m l Cable HRE Kgilal Gwer thre Ali eh Catia Cable 3440 FIGURE A NOTE Scanning the first PCTV Screen will take more time than the other units in the club Digital scanning can take up to 15 minutes After scanning the first PCTV Screen that configuration can be uploaded and downloaded to the other units being configured in the club 53 PROGRAMMING THE PCTV 4 4 SETTING UP THE PCTV CONTINUED 2 When the scan is successful the Save Configuration to Server screen will appear Touch SAVE CONFIGURATION TO SERVER Figure B NOTE lf the facility has given the installer a list of either digital or analog channels to modify or to order in a particular sequence see the instructions in the Appendix Modifying Channel Settings for modifying scanned channels Once the scanned channels have been modified the configuration still needs to be saved TV CONFIGURATION TV Tuner Configured Standard Analog Cable Channa J Lge aba R r eee Tv Core ju Net a i FIGURE B 3 On the next page select FINISH Figure C The PCTV Screen will reboot and come back up with a GO button Congratulations the installation process is complete When installation of all units at the site is complete
9. contact Netpulse at the on the screen FINISHED Congratulations this umit te installeci When You are compl t installing all units at this site please call 1 87 7 NETPULSE 7 877 563B5 7857 M you ore calling from within USA of Canada cr 01 415 645 0223 if you are calling from outside USA cr Canada A Metpuls e Support Tech will remotely test each unit while You are on thie call FIGURE C 54 PROGRAMMING THE PCTV 4 5 TESTING THE PCTV SCREEN After the PCTV units is installed and configured the functionality of the unit still needs to be tested to ensure it is working properly Starting and Registering 1 Touch GO 2 The first screen seen when the Go button is touched is the registration screen NOTE Some clubs will only use the standalone functionality If this is the case in this club touch Continue Without Registering If the club is connected use the keypad to enter the User ID that has been given for testing and Touch NEXT 3 Touch the password image given for testing and touch the next arrow Touching the next arrow will bring up the Main Menu Testing On Demand 1 Touch On Demand 2 Check an On Demand video and ensure it runs 3 Touch Menu to return to the main menu screen Testing Music Videos 1 Touch Music Videos on the main menu The Music Video screen will be displayed 2 Check one music Genre i e pop and ensure a video runs 3 Touch Menu to return to the main menu Tes
10. cover with the Matrix logo that makes up the top of the rear console cover is no longer used with a TV bracket 15 Mount the console back onto the unit making sure to make all the necessary wire connections including the coax cable net and power wires FIGURE N FIGURE O 16 Mount the plastic front plate to the TV Figure P 17 Plug the coax cable into the back of the TV Figure Q FIGURE Q FIGURE P 18 Plug the power wire into the back of the TV Figure R 19 Plug the side of the controller wire marked TO TV into the back of the TV Figure S NOTE The controller wire should be plugged into the PCTV port on the PCTV FIGURE S FIGURE R 27 BRACKET INSTALLATION amp CONSOLE SETUP 3 4 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LAM CONSOLE CONTINUED 20 If the system is wired plug the net wire yellow from the console into the Net port in the back of the PCTV Figure T If the system is wireless skip this step 21 If the PCTV will be using a wireless signal plug the dongle into the back of the TV and mount the USB flash drive to the console plastic using double sided foam tape Figure U FIGURE T FIGURE U 22 Put the TV into place on the TV bracket being sure to tuck the tabs of the plate installed during Step 16 into the console plastic to create a seamless look Figure V 23 Mount the TV to the TV bracket using 4 screws sent with the TV Figure W FIGURE V FI
11. mashing reveals pre folie pro pH rt ee ier S mrtree Narre mii HMirgtgrhsrga IE 4d Moe 1 Cori Ukru This medkirs war preci irvet ltlrd en te helpata netverk LIE Ksil Ei TE CIHRETKS C KS BC LH JT BADU CCM Hipika Miah ID kJ Mare te Pm ed Bare nrbsra IL i Meee MAP be TE 1 A T SPER PE bol rie hie ofa l kr CHECKE FOR UPDATES INSTALL netpulF FIGURE C 3 In a few seconds a green message should be seen saying All Network Tests have passed Touch the INSTALL key to Auto pair the Machine ID MID Figure D NOTE lt may take several seconds to connect to the network pair the machine Par patie SYSTEM PAIRING Pair this device to the Netpulse Authentication Server Press Test Network To confirm Connectivity amd then Inaral to install this unit on The Netpulte network Machine Re en rt hee PH We chine Con kur abe Getemar IP 16 7 58 1 bite Fade atl uli Cer m md IP k drep jh 1 BA kiitis GG Dd LC i D TS datewey Tals Rite VLU TPO llgklm ap ce ee ee gL mere Ted Peto ae Pee ar Brigama i V VE C di AN mebercrk saba pa a d n tpuls FIGURE D 51 52 PROGRAMMING THE PCTV 4 3 CONNECTING TO THE NETWORK CONTINUED 4 Once the unit has a new MID select NEXT Figure E NOTE If the MID does not appear and text is seen in RED stating that the MID could not be created contact Netpulse support at 1 877 NETPULSE ext 2 SYSTEM PAIRING Pair this device ta th
12. recommended Data Cat 5e or Cat 6 for Network Cabling TV COAXIAL CABLE FOR TV ELECTRICAL Standards e New network cabling must be installed according to BICSI and TIA standards and tested to meet ANSI TIA 568 C 2 Commercial Balanced Twisted Pair Telecommunications Cabling and Components Standard e Pre existing cabling must pass basic Qualification tests for speed and continuity e RJ45 test plugs shall fall within the values specified in ANSI TIA 568 C Annex C for NEXT FEXT and Return Loss TV 75 Ohm Standard TV Hook Ups RG 6 F Connector NOTE TV lines must be connected to TV source and signal strength must be tested If required TV signal amplifier must be installed Standard Analog TV signal must be tested at each coax cable termination and tuned to fall within the range of 4dB and 12dB signal loss 1 0 amp 120 VAC per Netpulse screen Netpulse does not require dedicated circuits Netpulse requires an electrical outlet in the phone closet to support the Internet connection Data and TV must be run in separate conduit from the electrical There should be no exposed TV or data wiring Netpulse recommends that clubs adhere to the American Disabilities Act ADA requirement of 36 inches for the spacing of walkways SIGNAL SPECIFICATIONS 7 3 TV TECHNICAL SPECIFICATIONS The TV signal source is either analog or digital It is likely the source is already configured for the facility If not see th
13. Example 3 Improper Installation Please see the Meraki MR installation guide for additional details on mounting the access point to different fixtures http docs meraki com download attachments 8519767 meraki_setup MR24 pdf version 1 amp modificationDate 1349988446756 NETWORK CONFIGURATION amp SETUP 2 2 SETTING UP A WIRELESS NETWORK CONTINUED 4 After all the APs are up and running perform a post installation coverage check There are many tools that can be loaded onto a laptop that will allow you to check RSSI received signal strength intensity values such as InSSIDer available for free from Metageek With this program or another program installed on a laptop or smartphone check the RSSI values around the fitness equipment Values that are greater than 70 dBm are required If it is noticed that the signal strength is significantly lower than this value 75 dBm or less consider installing additional access points NETWORK CONFIGURATION amp SETUP 2 3 GETTING CONNECTED GUIDE WIRED STEP 1 SITE READINESS customer responsibility PREPARING THE SITE 1 Find a secure location like an AV closet or a server room for the gateway and related network equipment 2 Make sure the location has power and internet access as well as a rack or 19 shelf for the gateway PREPARING INTERNET SERVICE 1 Contract an ISP Internet Service Provider to bring internet connectivity to the closet 2 Make sure that the int
14. GURE W 24 Put the back cover onto the TV and secure with 4 screws Figure X 25 Plug a network wire if using a PCTV not using wireless power wire and a coax cable with a signal strength of 10 Hz to the port on the front of the unit Figure Y 26 Enter Engineering Mode by pressing the INCLINE DOWN and SPEED DOWN keys at the same time and toggling to Engineering then press ENTER 27 Toggle to Audio Source and push ENTER Toggle to PCTV and push ENTER This will ensure the audio from the PCTV can be heard through the treadmill headphone jack 28 If the sound is too quiet or too loud toggle to Volume Control and push ENTER When the screen says Output Default push ENTER again The volume range can be adjusted 29 Press and hold the PAUSE or STOP key for 3 5 Seconds to return to normal operation 30 Achannel scan should be done using the instructions included in the TV owner s manual FIGURE X FIGURE Y BRACKET INSTALLATION amp CONSOLE SETUP 3 5 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LMM CONSOLE All T3x consoles have a minimum software version to allow a PCTV See the minimum software version for this console in the table in Section 3 8 The software versions can be checked in Manager Mode To enter Manager Mode press and hold ELEVATION and SPEED DOWN at the same time for 3 5 seconds Use the LEVEL keys to scroll to Manager Mode and press ENTER Then use the LEVEL keys to toggle to Software and hit ENTER Thi
15. INSTALLATION amp CONSOLE SETUP 3 6 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LAM CONSOLE CONTINUED NOTE The wire connections in Steps 12 15 should be done prior to installing the TV onto the bracket as the bracket will prevent some of the connections from being made 12 Plug the coax cable into the port on the TV Figure M 13 Plug the power wire into the port on the TV Figure N FIGURE M FIGURE N 14 Plug the controller wire into the PCTV port on the TV Figure O 15 Plug the net wire into the port on the TV If using wired internet Figure P FIGURE O E FIGURE P 16 Plug the dongle into the port on the TV if using wireless internet Figure Q 17 Mount the dongle to the TV plastic using double sided tape Figure R FIGUREQ FIGURE R 36 BRACKET INSTALLATION amp CONSOLE SETUP 3 6 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LAM CONSOLE CONTINUED 18 Mount the TV to the bracket using 4 screws sent with the TV Figure S 19 Make sure that the tabs on the front plate are tucked behind the console faceplate to create a seamless look Figure T F r FIGURE S FIGURE T 20 Install the console back cover removed in Step 2 Figure U NOTE Make sure that the coax power net and controller wires are tucked in the slot in the cover created by removing the small Matrix logo cover Figure V s a NU FIGURE U FIGURE V 21 Install t
16. INSTRUCTIONS Please make sure that the power cord is not plugged into the wall outlet while completing the following procedure For the installation of the PCTV a bracket kit containing various parts has been provided Please note that not all parts will be used for this installation as this kit is also used for other Matrix Fitness products Refer to the step by step instructions to determine which parts will be needed and which parts can be discarded To ensure correct assembly of the treadmill TV bracket carefully read and follow these steps ATTENTION The PCTV must be tested for function after installation as some programming may be needed If the channels come in only black and white or if only some channels are received reference the troubleshooting guide at the back of this manual or contact Matrix Fitness at 866 693 4863 The PCTV is a touch screen unit and therefore will not work with the entertainment keypad Leave the Target Heart Rate Overlay NOTE There is more than one version of the Universal 5x console please make sure the correct instructions for the console are being used 1 Turn off power and disconnect the power cord 2 Remove the console from the unit 3 Remove the 6 screws holding the 2 halves of the console together and split the console Figures A amp B a gt FIGURE A FIGURE B 4 Assemble the new head phone jack and wire Figure C 5 Remove the existing blank head phone jack cover NOTE The PCT
17. INUED Sign in Registration After the Attract Screen an exerciser may sign in as a registered user by signing in with their password they may proceed as a guest or they may create a new account Non Registered User Exercisers do not need to have a User ID or create an account in order to use the entertainment system instead they may select the continue as guest button to proceed to the main menu Main Menu The main menu is where the exerciser is directed after the sign in process The main menu displays featured content Virtual Active workout history and more Figure F TV showe sports updates Analog F podcasts are Thousands of Digital Tv more music videos Pao be wir Virtue Tai S Workout History My Flayliat virtual Burs Time Crore through Cut distance playlist for the world calories and Cassy access more FIGURE F PROGRAMMING THE PCTV 4 2 INSTALLATION On Screen Installer The PCTV screen by default will always start up in the Install Application until the install process via the steps in the application is complete to ensure each device is properly configured at the installation The installation application contains four views to lead the installer though configuring the screen 1 Welcome Screen 2 Default Settings language unit type etc 3 Network Selection wired wireless no network and authentication 4 TV Channel Scanning After the install application has been success
18. LE CONTINUED 20 If the PCTV is going to be connected to the internet through an Ethernet cable plug the Ethernet cable into the yellow Ethernet port on the bottom of the treadmill Figure U If the PCTV is wireless skip this step 21 Plug the TV power brick into the bottom of the treadmill Figure U 22 Plug a coax cable with a signal strength of 10 Hz into the bottom of the treadmill Figure U FIGURE U 23 Install the PCTV and console back covers Figure V FIGURE V 24 Enter Engineering Mode by pressing the INCLINE DOWN and SPEED DOWN keys at the same time and toggling to Engineering then press ENTER 25 Toggle to Audio Source and push ENTER Toggle to PCTV and push ENTER This will ensure the audio from the PCTV can be heard through the treadmill headphone jack 26 If the sound is too quiet or too loud toggle to Volume Control and push ENTER When the screen says Output Default push ENTER again The volume range can be adjusted 27 Press and hold the PAUSE or STOP key for 3 5 Seconds or press the EMERGENCY STOP to return to normal operation 28 A channel scan should be done using the instructions included in the TV owner s manual 33 34 BRACKET INSTALLATION amp CONSOLE SETUP 3 6 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LAM CONSOLE NOTE There is more than one version of the T3x console please make sure the correct instructions for the console are being used Figur
19. LEVEL keys to toggle through the versions to find the UCB software version Press and hold the PAUSE key to exit ASSEMBLY INSTRUCTIONS Remove the power cord from the wall outlet prior to completing the steps below For the installation of the PCTV a bracket kit has been provided containing various parts Please note that not all parts will be used for this installation as this kit is also used for other Matrix Fitness products Refer to the step by step instructions to determine which parts will be needed and which parts can be discarded To ensure correct assembly of the treadmill TV bracket carefully read and follow these steps ATTENTION The PCTV must be tested for function after installation as some programming may be needed NOTE The PCTV is a touch screen unit and therefore will not work with the entertainment keypad Leave the Target Heart Rate Overlay on the console NOTE There is more than one version of the T5x console please make sure the correct instructions for the console are being used 1 Assemble the treadmill as outlined in the Assembly Instructions Make sure that the coax cable is free and not wrapped around anything Figure A NOTE The PCTV is a touch screen unit and therefore will not work with the entertainment keypad Leave the Target Heart Rate Overlay on the console Figure B vannu RPilNmsmus mami FIGURE A FIGURE B 2 Remove the Matrix Fitness Logo from the console back and throw away Figure
20. MATRIX PCTV nu SERVICE MANUAL penn INTRODUCTION CHAPTER 1 INTRODUCTION 1 1 IMVOCGVENO0 K BAs a as as S Ss N END eae 1 CHAPTER 2 NETWORK CONFIGURATION amp SETUP 2 1 Getting Connected Guide Wireless i aaa 3 2 2 Setting up a Wireless Network iiiiiaa a 5 2 3 Getting Connected Guide WIre cccccccscccescccseecseecceeeceuceceeecsueecsueesaeesaeessaeeseeessueesaaeenes 9 CHAPTER 3 BRACKET INSTALLATION amp CONSOLE SETUP 3 1 PCTV Bracket Installation amp Console Setup 5x TM LMM Console iii a 12 3 2 PCTV Bracket Installation amp Console Setup 5x TM LAM Console 16 3 3 PCTV Bracket Installation amp Console Setup 5x Universal LMM Console 0008 20 3 4 PCTV Bracket Installation amp Console Setup 5x Universal LAM Console 00008 25 3 5 PCTV Bracket Installation amp Console Setup T3x LMM Console 29 3 6 PCTV Bracket Installation amp Console Setup T3x LAM Console cccccccssceeseeeeeeeeeeeees 34 3 7 PCTV Bracket Installation amp Console Setup Universal 3x Console cccccceeeeeeeeeeeeees 39 3 8 REGUIFEG Software V lsl6hS ts sniegs ii 44 CHAPTER 4 PROGRAMMING THE PCTV 4 1 DENNOM S zeta ee ao eesti as sj a Keis s 45 4 2 INSIAllAU0HS aessa a a a e EA 49 4 3 Connecting to the NeiWOfKi ssseuaisaubisimdsastka satu b s dist Aa its a rs m amgi ease gais 50 AA SEWUNGUPIN FOLV lt sd 53 4 lesu
21. MING THE PCTV 4 1 DEFINITIONS CONTINUED Screen Set up Settings Mode The set up mode for the product is accessible from the Attract Screen The touch sequence is upper left upper right upper right upper left This will display a keypad that will allow the person to enter a number of preset configuration passwords into the system to access various menus 1 At the main attract screen complete the top left top right top right top left tap sequence to bring up the menu code popup Figure C 2 Once the keypad appears Figure D enter the code followed by ENTER Figure E m Q Netpulse FIGURE C PROGRAMMING THE PCTV 4 1 DEFINITIONS CONTINUED pow 8 Netpulse FIGURE D Display IP and MAC STICK Mount USB device on TV and run script USB Install DEMO This allows ANY user login registration to succeed without a network connection Locally stored workout data will display in the Workout History feature SCAN Navigate to the TV channel scanning page of the install application to scan for TV channels INET Navigate to the networking page of the Install application to configure the machines to be network connected wired wireless or non connected DOWN Powers down the computer safely SPEED Display an Internet Speed Test to allow an on site technician to test the internet speed LANG Display and set default language FIGURE E 47 48 PROGRAMMING THE PCTV 4 1 DEFINITIONS CONT
22. P key for 3 5 Seconds to return to normal operation 30 A channel scan should be done using the instructions included in the TV owner s manual BRACKET INSTALLATION amp CONSOLE SETUP 3 4 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LAM CONSOLE NOTE There is more than one version of the Universal 5x console please make sure the correct instructions for the console are being used 1 Remove the console from the unit as outlined in Section 9 1 2 Remove the 6 screws holding the console front to the back and split the console Figures A amp B FIGURE A FIGURE B 3 Remove the 2 screws holding on the blank headphone jack plastic to the console and remove the plastic Figures C amp D D TEn ji cam l i Al 4 FIGURE C FIGURE D 4 Remove the wire in the console that goes from the UCB to the board on the console back Figure E 5 Install the new Y cable sent with the TV bracket kit to replace the wire removed in Step 4 Figure F sE FIGURE E p FIGURE F 25 BRACKET INSTALLATION amp CONSOLE SETUP 3 4 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LAM CONSOLE CONTINUED 6 Run the white end from the Y cable through the headphone jack hole in the console plastic and plug it into the headphone jack sent with the TV bracket set Figure G 7 Mount the headphone jack into the console plastic using the 2 screws removed in Step 3 Figure H
23. RE L 12 Route the TV power and net wires through the console These wires do not plug into the console but should protrude from the top and bottom opening of the console There should now be 4 wires protruding from the top of the console coax power net and controller wires Figure M 13 Use the 4 screws removed in Step 4 to re attach the 2 halves of the console Be careful not to pinch any of the TV wiring 14 Install the bracket to the console using 4 screws Figure N FIGURE M FIGURE N 15 Install the console back onto the console mast and secure it with 5 screws Figure O Make sure to make all wiring connections including the net wire if using wired internet power wire and coax cable Tuck all the wiring into the console or mast to prevent any pinching 16 Plug the power wire into the back of the TV Figure P FIGURE O FIGURE P 41 BRACKET INSTALLATION amp CONSOLE SETUP 3 7 PCTV BRACKET INSTALLATION amp CONSOLE SETUP UNIVERSAL 3x CONSOLE CONTINUED 17 Plug the side of the controller wire labeled TO TV into the port Titled PCTV Figure Q 18 If the system is wired plug the Net Wire from the TV Bracket kit into the Net port in the back of the PCTV Figure R If the system is wire less skip this step FIGURE Q FIGURE R 19 If the PCTV is wireless plug the wireless dongle into the USB port on the back of the PCTV Figure S and use the double sided tape to secure the dongle to the PC
24. SOLE SETUP 3 2 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x TM LAM CONSOLE CONTINUED 12 Plug the net wire into the Net port on the PCTV if wired internet will be used Figure M 13 If wireless internet will be used plug the dongle into the port of the PCTV Figure N and mount the dongle to the PCTV plastic using double sided foam tape FIGURE M FIGURE N 14 Mount the PCTV to the bracket using 4 screws Figure O NOTE Make sure the tabs of the front plate slide behind the console faceplate to create a seamless look Figure P FIGURE O FIGURE P 15 Install the console back cover using the 4 screws removed in Step 1 Figure Q NOTE Make sure to route the wiring through the holes in Figure R The MATRIX logo portion of the back cover will not be used with a TV bracket LI the back cover so that none of the wiring is pinched FIGURE R FIGURE O 18 BRACKET INSTALLATION amp CONSOLE SETUP 3 2 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x TM LAM CONSOLE CONTINUED 16 Install the TV back cover using 4 screws Figure S 17 Plug the PCTV power wire into the port on the front of the treadmill near the power switch Figure T i FIGURE S FIGURE T 18 Plug a coax cable with a signal strength of 10 Hz into the front of the treadmill near the power cord Figure U 19 if using wired internet plug a net wire into the port on the front of the treadmill near the power switch
25. STOP key for 3 5 Seconds to return to normal operation 30 Achannel scan should be done using the instructions included in the TV owner s manual 43 44 BRACKET INSTALLATION amp CONSOLE SETUP 3 8 REQUIRED SOFTWARE VERSIONS All consoles have a minimum software version for functioning with a PCTV Refer to the table below for minimum acceptable software versions for each console If the software version on the console is the one listed or higher it will allow installation of a PCTV PROGRAMMING THE PCTV 4 1 DEFINITIONS Attract Screen The Attract Screen displays a Go button to begin the session and a Screen Off On button to turn the screen black when the exerciser does not desire to use the product Go Button The exerciser upon selection of this button will go to sign in registration page Screen Off On Button When the user selects this button the screen will go black with a button to return the screen to its full Attract Screen If an exerciser selects the screen on button or after 30 minutes the screen will return to the Attract Screen Figure A MATRIX SCREEN OFF FIGURE A Network Availability Icon In the lower right hand corner of the view the icon below will display if the screen is unable to connect to the Internet Figure B This network check is done every 5 minutes If at any time the server availability changes the icon will be hidden FIGURE B 45 46 PROGRAM
26. TV plastics Figure T FIGURE S FIGURE T 20 Install the PCTV onto the bracket making sure that the tabs on the TV lower plastic shield fit into the slots in back of the console Figure U and secure the PCTV to the bracket with 4 screws Figure V FIGURE U FIGURE V 42 BRACKET INSTALLATION amp CONSOLE SETUP 3 7 PCTV BRACKET INSTALLATION amp CONSOLE SETUP UNIVERSAL 3x CONSOLE CONTINUED 21 Run the coax cable from the top of the console to the back of the PCTV and screw it in Figure W 22 Install the PCTV back cover Figure X FIGURE W FIGURE X 23 If the PCTV is going to be connected to the internet through an Ethernet cable plug the Ethernet cable into the yellow Ethernet port on the bottom of the unit Figure Y If the PCTV is wireless skip this step 24 Install the external TV power cord and screw it in Figure Y 25 Install the coax cable at the base of the unit Figure Y FIGURE Y 26 Enter Engineering Mode by pressing the LEVEL UP and LEVEL DOWN keys at the same time and toggling to Engineering then press EN TER 27 Toggle to Audio Source and push ENTER Toggle to PCTV and push ENTER This will ensure the audio from the PCTV can be heard through the treadmill headphone jack 28 If the sound is too quiet or too loud toggle to Volume Control and push ENTER When the screen says Output Default push ENTER again The volume range can be adjusted 29 Press and hold the PAUSE or
27. V is a touch screen unit and therefore will not work with the entertainment keypad Leave the Target Heart Rate Overlay on the console Figure D Earphone Board Fa i m T a ON du a 1 a Earphone aag Wire A SS NI et mu FIGURE C FIGURE D BRACKET INSTALLATION amp CONSOLE SETUP 3 3 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LMM CONSOLE CONTINUED 6 Plug the head phone jack wire into the upper board and the connection board on the console back cover Figures E amp F and put the console back together by replacing the screws removed in Step 3 NOTE There is an existing wire in the UCB and connection board that will need to be removed and discarded SS oo FIGURE E FIGURE F 7 Remove the 4 screws holding the small Matrix Fitness logo to the front of the console mast and remove the logo Figures G amp H This piece is no longer needed FIGURE H FIGURE G 8 Install the rubber pad from the TV bracket kit over the hole in the console mast Figures amp J Tas FIGURE FIGURE J 21 BRACKET INSTALLATION amp CONSOLE SETUP 3 3 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x UNIVERSAL LMM CONSOLE CONTINUED 9 Connect the net wire and coax cable from the TV to the ones coming up the console mast the coax connection will use an adaptor from the bracket kit and push the TV power wire into the console mast so that it is accessible Figure K
28. acility and displayed on any TV including the Netpulse screens 0 Cable Satellite Box Modulator Combiner Coaxial Cable to TVs d al LIFETIME L Ea m 63 64 NOTES MATRIX PC V M SERVICE MANUAL lt Created amp Maintained by Kevin Oeltjenbruns 3 7 13
29. and all distribution Hubs Switches units Ensure that Cat 6 is securely connected to each unit If the Internet cable is secure a link light on the unit where the cable attaches should be seen One unit has no On Demand TV Shows or Machine has lost connection to Gateway Check all Cat 6 connections between Music Videos machine and Gateway Ensure Cat 6 is securely connected at machine Reboot unit Retest video on demand or music video If the problem is not resolved contact Matrix Technical Support 6 3 TROUBLESHOOTING LIVE TV ISSUES SYMPTOM CAUSE RESOLUTION All units No TV TV system is down or coax cabling 1 Check electrical connections at TV head disconnected in closet end system 2 Check coaxial cable in server room or electrical closet 3 Contact the TV vendor All units have fuzzy picture Loose or damaged coax cabling at closet or Check coaxial cable and connections in TV signal strength problem server room or electrical closet and main segment feeding all machines Contact the TV vendor One unit TV not working Loose coax cable connection or poor signal _ Ensure coax cable and connections are strength secure Shut down and restart machine Test unit to ensure it is working Contact Matrix Technical Support Video Present when viewing TV but not Loose or unplugged S Video cable to console 1 Check S Video connection at console present when viewing iPod video side access area Check for damaged
30. ated which include wiring switches wire management and in wall terminations going wireless is often a much more cost effective solution NETWORK CONFIGURATION amp SETUP 2 1 GETTING CONNECTED GUIDE WIRELESS CONTINUED FACILITY RESPONSIBILITIES BEFORE INSTALLATION HOW TO PREP The FACILITY Bring a Coaxial TV cable and wireless signal to each PCTV A designated wireless installation team should install the wireless infrastructure Here s how to prep Find a secure location such as an AV closet or a server room that has available space for the Gateway Server an outlet and a surge protector Make available a 19 shelf near available power Contact an ISP Internet Service Provider to bring internet connectivity to the closet Make internet access available in the shelf area We recommend a dedicated line WHAT IS NEEDED FOR INTERNET Insure sufficient bandwidth for the Gateway Server A bandwidth of 1 Mbps download speed for every 4 touchscreens is recommended The minimum bandwidth is 3 Mbps download speed GATEWAY SERVER r WIRELESS ACCESS POINT HIGH SPEED INTERNET NETWORK CONFIGURATION amp SETUP 2 2 SETTING UP A WIRELESS NETWORK OVERVIEW There are 4 basic steps required to design a wireless network They are 1 Identifying areas that need coverage and estimating the number of APs needed a Wireless coverage only needs to be provided in areas where car
31. ay 1 Turn off power and disconnect the power cord 2 Remove the console from the unit 3 Remove the 2 screws holding the small silver back cover to the console and remove the back cover Figures A amp B FIGURE A FIGURE B 4 Remove the 4 screws holding the rear half of the console to the front half and split the console Figures C amp D FIGURE C FIGURE D 39 BRACKET INSTALLATION amp CONSOLE SETUP 3 7 PCTV BRACKET INSTALLATION amp CONSOLE SETUP UNIVERSAL 3x CONSOLE CONTINUED 5 Remove the 5 screws holding the lower keypad plastic to the front of the console Figures E amp F FIGURE E FIGURE F 6 Install a head phone jack to the new lower keypad plastic with a slot for the Headphone Jack Figure G 7 Remove the Entertainment Keypad and install the Target Heart Rate Overlay to the lower keypad plastic Figure H ATE rt LM EB ee ee ee FIGURE G FIGURE H 8 Plug the head phone jack wire into the head phone jack Figure 9 Plug the head phone jack wire into the UCB Figure J FIGURE FIGURE J 40 BRACKET INSTALLATION amp CONSOLE SETUP 3 7 PCTV BRACKET INSTALLATION amp CONSOLE SETUP UNIVERSAL 3x CONSOLE CONTINUED 10 Plug the coax cable into the coax adaptor attached to the back half of the console Figure K 11 Plug the side of the controller cable labeled To Console into the C Safe port near the top of the UCB Figure L FIGURE K FIGU
32. dio machines equipment need to have a wireless connection If there are spaces in the facility that don t have cardio machines there is no need to install access points in that area b Once the areas needing coverage have been identified calculate the minimum number of access points APs needed to support the equipment This number is only a starting point additional access points will be required depending on the physical distribution of the equipment and the RF challenges presented by the environment c The next step in designing a network is to determine the distance from the AP that each piece of equipment will be placed Equipment cannot be placed further than 50 feet away from any given access point This limitation is a best case scenario and only applies to equipment that has direct line of sight to the access point If there are walls floors lighting fixtures windows or other obstructions that block the line of sight to the access point the maximum distance the equipment can be from the access point is reduced significantly and will need to be determined with empirical testing For each group of equipment stand in the center of the group and measure the distance to the furthest piece of equipment If this distance is greater than 50 feet an additional AP is needed to cover this group of equipment If equipment is installed on different floors additional APs should be used to cover the floors separately d Ceiling height also affec
33. e Netpulse Authentication Server Press Test Network TO confirm connectivity and then Install to instali this unit On the Nerpuise NeTWork ee dj IP ee it r art athi Jalopy hgt rip W di 10 75 1593 MAC Aie 00 74 FE 01 275 JL tr ur j Task bite 2 107 50 Lipia pedis fee es erver Terl lp oe Fee veel Sey a re eee Al Fe m dk eii pated Server tell eg pA a ee a Hee a a PEEL Be Hii LI im 15 Hati m Te mr J dr m LU PERU HA PA PL e I inaFallaFkrar mas zmrrauul paw Fri kuru e AFA netpulse FIGURE E 5 Reboot the PCTV by removing the power by unplugging the power wire from the back of the PCTV PROGRAMMING THE PCTV 4 4 SETTING UP THE PCTV After rebooting the next screen will let a user set up the TV Figure A Use Existing Configuration If the PCTV Screen has been previously configured choose this option to use the existing configuration When a user choose this option the user bypasses the scanning process This option is used after the PCTV Screen unit is set up and facility staff has requested changes to the TV channels Download Configuration If other units have been configured and uploaded to the server choose this option to download the configuration Choosing this option bypasses the scanning process Analog or Digital If this is the first PCTV Screen in the club the user has to choose either analog or digital in order to scan the channels available 1 Once the correct options
34. e and PCTV back covers Figure Q NOTE Be sure to route the cables to the TV through the hole in the console back cover created by removing the Matrix Fitness logo plate Figure R F FIGUREQ FIGURE R 18 Enter Engineering Mode by pressing the INCLINE DOWN and SPEED DOWN keys at the same time and toggling to Engineering and press ENTER 19 Toggle to Audio Source and push ENTER Toggle to PCTV and push ENTER This will ensure the audio from the PCTV can be heard through the treadmill headphone jack 20 If the sound is too quiet or too loud toggle to Volume Control and push ENTER When the screen says Output Default push ENTER again The volume range can be adjusted 21 Press and hold the PAUSE or STOP key for 3 5 Seconds or press the EMERGENCY STOP to return to normal operation 22 A channel scan should be done using the instructions included in the TV owner s manual 15 BRACKET INSTALLATION amp CONSOLE SETUP 3 2 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x TM LAM CONSOLE CONTINUED NOTE There is more than one version of the T5x console please make sure the correct instructions for the console are being used 1 Remove the 4 screws holding the console back cover to the front and remove the console back cover Figures A amp B FIGUREA FIGURE B 2 Slide the TV bracket between the console frame and the fan frame Figure C 3 Secure the TV bracket to the console usi
35. e console cable included with the TV Bracket kit Use the provided adaptor to connect the coax cable from the PCTV to the coax from the console mast Run the coax cable to the back of the PCTV and screw it in Figure L 11 Plug the external TV power wire from the console mast into the TV power wire installed in step 4 Both wires are labeled TV Figure M FIGURE L FIGURE M 12 Plug the controller wire from the TV bracket kit into the C Safe port on the upper control board in the console Figure N There may be a C Safe cable already plugged into the console upper board which is standard from the factory This should be unplugged and remain unplugged inside the console 13 If the system is wired plug the Net Wire from Step 6 into the 8 pin connector coming up the console mast with the console cable Figure O If the system is wireless skip this step FIGURE N 14 BRACKET INSTALLATION amp CONSOLE SETUP 3 1 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x TM LMM CONSOLE CONTINUED 14 If the PCTV is going to be connected to the internet through an Ethernet cable plug the Ethernet cable into the yellow Ethernet port on the bottom of the treadmill Figure P If the PCTV is wireless skip this step 15 Plug the TV power brick into the bottom of the treadmill Figure P 16 Plug a coax cable with a signal strength of 10 Hz into the bottom of the treadmill Figure P FIGURE P 17 Install the consol
36. e following Analog If the facility has traditional cable TV analog the coaxial cable can be run directly to the Netpulse screens and connect to the coaxial connector on the back of the screen Analog TV signal must be tested at each coax cable termination and tuned to fall within the range of 4dB and 12dB signal loss Digital If the facility has digital cable or satellite TV service Dish or DirecTV which requires a box from the cable satellite provider to view the signal a head end will need to be in place to be able to view and change all TV channels from the Netpulse screens or any personal screen device A local Audio Visual contractor will easily be able to create a system a As many cable satellite boxes as channels will be needed to display in the club If 8 channels are needed then 8 boxes are needed The individual channel chosen e g ESPN can be changed at any time but additional boxes may be required to have additional channels b The output of each of these boxes will go into a modulator that will assign a channel number for each box This is the channel chosen from the TV or Netpulse screen So for example in the below figure select channel 7 to view CBS since the box with CBS has been assigned to channel 7 c The signal from each modulator will then be combined via a combiner into a single coaxial cable d The coaxial cable will now contain all the channels in the system and can be run to anywhere in the f
37. ernet has sufficient bandwidth for the Gateway a The minimum bandwidth is 3 Mbps down b Recommended is a bandwidth of 1 Mbps down for every 4 cardio units 3 The Gateway is configured to accept a Dynamic IP address DCHP If only a Static IP address can be provided Netpulse must be contacted prior to Gateway shipment STEP 2 GATEWAY amp SWITCH INSTALLATION 3rd party installer responsibility A Connect the modem to the Gateway with a patch cable B Connect the Gateway to the Switch with a patch cable C Connect the Modem Switch and Gateway to a power source D Plug patch cables from the Switch to the Patch Panel E Label the jacks on the Patch Panel and the corresponding jacks on the fitness floor as well Patch pane Patch cables Dsl cabl modem K tpul Media Galeway S Witch Power sourc NETWORK CONFIGURATION amp SETUP 2 3 GETTING CONNECTED GUIDE WIRED CONTINUED CLOSER DETAIL OF GATEWAY Netpulse Gateway Ethernet cable Ethernet cable Hub Switch es gr F B E j I A R le If d Eu l La j ar me e Fitness Facility Internet Connection Hub Router Modem etc internet Netpulse PCTV Compatible Cardio Equipment from Matrix Fitness NETWORK CONFIGURATION amp SETUP 2 3 GETTING CONNECTED GUIDE WIRED CONTINUED STEP 1 CLUB ETHERNET WIRING customer r
38. es A amp B FIGURE A FIGURE B 2 Cut the wire tie holding the coax cable power wire net wire and controller wire to the console frame Figure C 3 Mount the TV bracket to the frame using 4 socket head screws sent with the bracket kit Figure D FIGURE C FIGURE D 4 Remove the blank head phone plate from the front of the console 5 Install the new headphone jack plastic and wiring into the console Figure E 6 Plug the headphone wire into the open port on the translator board labeled For Phone Figure F Le EL ae E FIGURE E FIGURE F BRACKET INSTALLATION amp CONSOLE SETUP 3 6 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LAM CONSOLE CONTINUED 7 Mount the front plate to the TV using 2 screws sent with the bracket kit Figure G 8 Connect the power wire extension wire to the power wire coming from the base of the unit Figure H FIGURE G FIGURE H 9 Install the coax adaptor sent with the bracket kit to the coax cable coming from the base of the unit Figure and connect the coax extension cable to the cable coming from the base of the unit Figure J a i M FIGURE FIGURE J 10 Connect the net extension wire to the wire coming from the base of the unit Figure K 11 Locate the TV controller wire in the console Figure L This wire was part of the group of wires attached to the console by a tie strap removed in Step 3 FIGURE K FIGURE L 35 BRACKET
39. esponsibility ETHERNET WIRING OPTIONS Each piece of cardio equipment that will be equipped with a PCTV requires connectivity to the Gateway via Ethernet CAT6 cabling is recommended CAT5e is acceptable if CAT6 is unavailable Cable Wiring Option 1 Home Runs Run cable s directly from the patch panel to each touchscreen and terminate with a coupler This option is more secure but can be expensive depending on the size and layout of the club Cable Wiring Option 2 Switches on the Floor Cable from the Patch Panels to switch es on the floor and from the floor switches to the screens This is a less expensive option but leaves more opportunity for disconnection IMPORTANT Commercial grade cable management systems should be used to protect all cabling and distribution hubs from foot traffic tampering and accidental disconnects 11 12 BRACKET INSTALLATION amp CONSOLE SETUP 3 1 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x TM LMM CONSOLE All T5x consoles have a minimum software version to allow a PCTV See the minimum software version for this console in the table in Section 3 8 Check the software versions in Manager Mode To enter Manager Mode press and hold ELEVATION and SPEED DOWN at the same time for 3 5 seconds Use the LEVEL keys to scroll to Manager Mode and press ENTER Then use the LEVEL keys to toggle to Software and hit ENTER This will display the current software versions Use the
40. ful completed the PCTV screen will start in normal mode After installation the settings can be accessed by entering the screen touch sequence and code as detailed in the above Settings Set up mode Screen Configuration Wizard The configuration wizard takes a user through the steps to install the features of the PCTV Screen These features will let club members view TV video on demand and gather statistics of their workouts After configuring the PCTV Screen The PCTV must be tested it to ensure all the features are working properly After it is confirmed that the PCTV Screen is working correctly complete the installation Prerequisites Before using this configuration wizard each PCTV Screen should be cabled as described in Chapter 3 with the following e If wired Cat 5e Cat 6 Ethernet wiring for video on demand e If wireless Wireless USB card connected to Access Point e Coaxial cable for TV viewing e C SAFE cable Tasks Once power is connected to the system the system will boot up Perform the following e Connect pair the PCTV Screen with the Gateway and the back end server so that media can be downloaded to the PCTV Screen and workout statistics can be stored for users e Install and configure the TV tuner so users can watch TV shows on the PCTV screen e Test the unit to ensure the TV and video on demand work correctly e Ensure the unit gathers workout statistics e Complete the installation of the unit by en
41. ges 10 workouts per machine per day User Sign in 100 bytes per workout sent at start of a workout Saving session data 2kb per workout sent at the end of a workout Club messaging 6kb per workout sent during the workout RSS feed updates 80kb per club every 4 hours to the Gateway time interval can be adjusted Internet Traffic Nighttime All traffic below uses port 80 Video Programming 250 MB nightly per club Application Updates 10MB 20x per year per club User Interface Updates 8MB 3x per year per club NSi Units Coaxial Connection Standard 75 ohm terminated in a F Connector Port Electrical 1 0 amps of 120 volt AC Network Connection Ethernet connection terminated in a RJ 45 jack this must be wired back to the Netpulse Gateway so it is on the same subnet to permit remote updates 61 62 TECHNICAL SPECIFICATIONS 7 2 SYSTEM TECHNICAL SPECIFICATIONS The following table describes the details of the network TV and electrical components of the system Components should meet the following component criteria SYSTEM COMPONANT EXPLANATION Pin Out Information 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown T568B Straight through data cable Number all jacks at Netpulse equipment location Numbering should correspond to patch panel at data equipment location NOTE Data line needs to be terminated into the phone closet patch panel is
42. he TV back cover onto the TV Figure W 22 Plug a working coax cable with a signal strength of 10 Hz to the port at the base of the treadmill Figure X PA aoid die Z a K r FIGURE W g FIGURE X 37 38 BRACKET INSTALLATION amp CONSOLE SETUP 3 6 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LAM CONSOLE CONTINUED 23 Plug the TV power wire into the port at the base of the treadmill Figure Y 24 Plug a network cable into the port at the base of the treadmill if using wired internet Figure Z FIGUREY FIGURE Z 25 Enter Engineering Mode by pressing the INCLINE DOWN and SPEED DOWN keys at the same time and toggling to Engineering then press ENTER 26 Toggle to Audio Source and push ENTER Toggle to PCTV and push ENTER This will ensure the audio from the PCTV can be heard through the treadmill headphone jack 27 If the sound is too quiet or too loud toggle to Volume Control and push ENTER When the screen says Output Default push ENTER again The volume range can be adjusted 28 Press and hold the PAUSE or STOP key for 3 5 Seconds or press the EMERGENCY STOP to return to normal operation 29 Achannel scan should be done using the instructions included in the TV owner s manual BRACKET INSTALLATION amp CONSOLE SETUP 3 7 PCTV BRACKET INSTALLATION amp CONSOLE SETUP UNIVERSAL 3x CONSOLE All Universal 3x consoles have a minimum software version to allow a PCTV See the minimum softwa
43. he new head phone jack and wire to the new cover Figure B and install the new head phone jack cover and wire to the console Figure C Plug the head phone jack wire into the 4 pin wire coming from the translator board Figure D FIGURE A FIGURE B FIGURE C I FIGURE D 29 30 BRACKET INSTALLATION amp CONSOLE SETUP 3 5 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LMM CONSOLE CONTINUED NOTE The PCTV is a touch screen unit and therefore will not work with the entertainment keypad Leave the Standard Overlay on Figure E 6 Feed the coax cable and TV power wire 4 pins both wires come up the console mast and controller signal wire 8 pins from the console through the hole in the handlebar frame below the console Figure F FIGURE E 7 Remove the 4 screws holding the upper handlebar assembly to the console masts Figure G 8 Mount the TV bracket to the frame using the 4 screws removed in Step 7 Figures H and I FIGURE G FIGURE H 9 Connect the coax cable that was fed through the hole in the handlebar frame in Step 6 to the cable coming out of the TV bracket using the coax adaptor sent with the bracket kit Figure J 10 Re install the console onto the handlebar frame FIGURE J BRACKET INSTALLATION amp CONSOLE SETUP 3 5 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LMM CONSOLE CONTINUED 11 Plug the power wire into the back of the PCTV Figure K 12 Pl
44. ibration Press and release the touch screen touch points calibration button located on the back of the console If it does not go immediately to the calibration screen repeat the press and release of this button Once the calibration screen appears complete the touch screen calibration If a problem with a Netpulse compatible machine is seen follow the directions in this troubleshooting guide to solve the problem If the problem cannot be resolved call Netpulse at 877 NETPULSE 638 7857 TECHNICAL SPECIFICATIONS 7 1 GATEWAY TECHNICAL SPECIFICATIONS Chassis Form Factor 10 2 x 2 3 x 7 3 Connectivity Dual Ethernet Ports Electrical 12v torage 500 GB Operating System Linux Netpulse Custom Variant Ubuntu 10 04 IP Configuration The Gateway will receive an IP address from the Club Network either static or DHCP and will issue IPs to each Netpulse compatible screen via DHCP on a separate subnet e g 10 4 6 2 than the host network The Gateway establishes an outbound VPN connection to Netpulse Cloud Controller for service and remote monitoring The VPN is perpetual and will automatically reestablish if the connection is lost VPN uses TCP and encrypted UDP protocol If the firewall blocks any outbound ports a single port will be assigned that will need to be open as all services will be re routed over that one port Internet Traffic Daytime All traffic below uses port 80 Typical network usage avera
45. lse can be setup via a wired or wireless system Based on the needs of the facility the facility will determine which setup is to be installed IMPORTANT Many of the components and kits that are sent by Matrix Fitness for the PCTV setup including overlays brackets and wires are used for multiple Matrix Fitness products Not all parts sent will be used for the PCTV by Matrix Fitness feature Be sure to read carefully through all setup steps to confirm which cables and components are needed and which components are to be set aside NETWORK CONFIGURATION amp SETUP 2 1 GETTING CONNECTED GUIDE WIRELESS WHY WIRELESS HOW WIRELESS WORKS WITH NETPULSE Netpulse compatible screens communicate to the internet via Wireless Access Points in the Facility Each Access Point is connected to a local Gateway Media Server at the Facility which is connected to the internet One Access Point can power 20 Netpulse PCTVs THERE ARE THREE KEY REASONS A FACILITY WILL WANT TO GO WIRELESS 1 EASY Without wires to run throughout the facility installation is fast and easy expansion is easy and there is almost no disruption to club members 2 RELIABLE This wireless infrastructure currently powers 20 000 customer networks in 143 countries The hardware is professional grade cloud managed and dual band which allows it to communicate to the equipment above other wireless noise 3 COST EFFECTIVE When the true expenses of wiring a facility are calcul
46. ndg b lbGlvVS560 66 x1 esudaendssdsd gk 55 CHAPTER 5 SETTING UP A USER PROFILE 5 1 selihno up da USefrFf0ll6ss boss dead a sete E nts des 56 CHAPTER 6 TROUBLESHOOTING 6 1 Troubleshooting General Issues aaa 58 6 2 Troubleshooting On Demand TV or Music Video Issues aaa 59 6 3 Troubleshooting Workout Reporting Issues i aaa 60 CHAPTER 7 TECHNICAL SPECIFICATIONS 7 1 Gateway Technical pecilic tlONS zassssiss oss gaiss ieee js 61 7 2 System Technical Specificatlons ii aaa 62 733 1V lecnifica Sp cilic l0f sas sue ad eusedsostl oswda eewsuweedsterinedsifeyisdveisaudiesw dotdasd egs 63 INTRODUCTION 1 1 INTRODUCTION PCTV By Matrix Fitness The Matrix PCTV combines the multimedia capabilities and Internet connectivity of a tablet computer with the high resolution picture of a broadcast TV bringing them directly to a facility s cardiovascular equipment The Matrix Fitness PCTV system is powered by Netpulse and delivers e An interactive media platform with a touchscreen interface e Thousands of On Demand TV shows On Demand Music Videos and Live TV e Individual login to track and store your workout information e Additional customization through Netpulse s website This document sets forth the requirements and best practices that will ensure the highest availability and reliability of the PCTV by Matrix Fitness experience for facility members and staff The PCTV System powered by Netpu
47. ng the 4 socket head screws sent with the bracket kit Figure D FIGURE C FIGURE D 4 Attach the coax cable from the TV bracket kit to the coax cable coming up the console mast Figure E NOTE There is an adaptor to hook the 2 male coax cable ends together included with the TV bracket kit 5 Attach the 4 pin black connector side of the power wire to the TV power wire coming up the console mast Figure F a lt E a re ba FIGURE E FIGURE F 16 BRACKET INSTALLATION amp CONSOLE SETUP 3 2 PCTV BRACKET INSTALLATION amp CONSOLE SETUP 5x TM LAM CONSOLE CONTINUED 6 Plug the controller wire this will have a white RJ45 connector on one end into the bottom left hand corner of the UCB Figure G NOTE There is a wire in this location that will need to be removed to plug in the controller wire 7 Plug the net wire this will have a yellow RJ45 connector on one end into the net wire coming up the console mast Figure H NOTE The net wire is only needed if wired internet will be used FIGURE G FIGURE H 8 Mount the front plate to the TV using 2 screws sent with the TV bracket kit Figure 1 9 Plug the coax cable into the port on the PCTV Figure J FIGURE FIGURE J 10 Plug the TV power wire into the port on the PCTV Figure K 11 Plug end of the controller wire labeled To TV into the port marked PCTV on the PCTV Figure L FIGURE K FIGURE L 17 BRACKET INSTALLATION amp CON
48. o it makes little to no difference how the AP is rotated about the Z axis when mounting The patterns are asymmetrical in the elevation plane XZ with significantly more antenna gain in the area directly above the plane formed by the access point Z This results in a coverage pattern that resembles an inverted cone whose axis of symmetry is normal to the plane of the AP See the diagram below for a side view of the green coverage zone With this type of coverage pattern it is very important to mount the AP so that the base of the coverage cone covers the desired wireless equipment This can be accomplished by mounting the AP to the ceiling above the equipment with the face of the AP the side with the LED lights pointed down toward the floor Alternatively the AP can be mounted on a wall at the approximate height of the equipment antennas with the face of the AP the side with the LED lights pointed at the equipment Do not mount the AP level with the equipment and the face pointed up at the ceiling as this will not achieve the desired coverage pattern NETWORK CONFIGURATION amp SETUP 2 2 SETTING UP A WIRELESS NETWORK CONTINUED See diagrams below Examples 1 and 2 show proper mounting placements Example 3 illustrates a situation to avoid Hack of AP T GOOD COVERAGE Example 1 Ceiling Installation Wall mr GOOD COVERAGE Example 2 Wall Installation LOVETaARe LONE a BAD COVERAGE t Face of AP a
49. onnection Check power connections Check AC power connection to wall adapter Check DC power connection to side access area of console Check DC in line connection between wall adapter and treadmill pre threaded internal cable 2 Shut down unit and restart unit 3 Test unit to ensure it is working 4 Check if RED LED is lit on front lower corner LED on indicates 12V is present from the wall adapter 5 Check that the GREEN LED is on LED on indicates CPU board is powered up Try pressing and releasing the button on the bottom center of the console to toggle the CPU power on function 6 Contact Matrix Support Unit did not completely boot or is otherwise Console CPU is locked up Press and hold the reset button on the unresponsive back of the console for 10 seconds to force a console reboot If a problem with a Netpulse compatible machine is seen follow the directions in this troubleshooting guide to solve the problem If the problem cannot be resolved call Netpulse at 877 NETPULSE 638 7857 TROUBLESHOOTING 6 2 TROUBLESHOOTING ON DEMAND TV OR MUSIC VIDEO ISSUES SYMPTOM CAUSE RESOLUTION All units On Demand Music Videos do not Problem with Gateway network switch or Check power on Netpulse Gateway play Cat 6 cabling at switch or patch panel and network switch in server room or electrical closet Restore as needed Ensure the Cat 6 cable is securely connected to the Gateway network switch patch panels
50. re version for this console in the table in Section 3 8 The software versions can be found in Manager Mode To enter Manager Mode press and hold LEVEL UP and DOWN at the same time for 3 5 seconds Use the LEVEL keys to scroll to Manager Mode and press ENTER Then use the LEVEL keys to toggle to Software and hit ENTER This will display the current software versions Use the LEVEL keys to toggle through the versions to find the UCB software version Press and hold the PAUSE key to exit ASSEMBLY INSTRUCTIONS Please make sure that the power cord is not plugged into the wall outlet while completing the following procedure For the installation of the PCTV a bracket kit has been provided containing various parts Please note that not all parts will be used for this installation as this kit is also used for other Matrix Fitness products Refer to the step by step instructions to determine which parts will be needed and which parts can be discarded To ensure correct assembly of the treadmill TV bracket carefully read and follow these steps ATTENTION The PCTV must be tested for function after installation as some programming may be needed If the channels come in only black and white or if only some channels are received reference the troubleshooting guide at the back of this manual or contact Matrix Fitness at 866 693 4863 The PCTV is a touch screen unit and therefore will not work with the entertainment keypad Install the Target Heart Rate Overl
51. s will display the current software versions Use the LEVEL keys to toggle through the versions to find the UCB software version Press and hold the PAUSE key to exit ASSEMBLY INSTRUCTIONS Please make sure that the power cord is not plugged into the wall outlet while completing the following procedure For the installation of the PCTV A bracket kit containing various parts has been provided Please note that not all parts will be used for this installation as this kit is also used for other Matrix Fitness products Refer to the step by step instructions to determine which parts will be needed and which parts can be discarded To ensure correct assembly of the treadmill TV bracket carefully read and follow these steps ATTENTION The PCTV must be tested for function after installation as some programming may be needed If the channels come in only black and white or if only some channels are received reference the troubleshooting guide at the back of this manual or contact Matrix Fitness at 866 693 4863 NOTE The PCTV is a touch screen unit and therefore will not work with the entertainment keypad Leave the Stan dard Overlay on NOTE There is more than one version of the T3x console please make sure the correct instructions for the console are being used 1 Turn off power and remove the power cord 2 Remove the console 3 Remove the console back cover 4 Remove the existing blank head phone jack cover Figure A 5 Assemble t
52. suring proper cable routing and secure the back panel 49 PROGRAMMING THE PCTV 4 3 CONNECTING TO THE NETWORK The following steps will let a user connect to the network so that media can be downloaded to the unit and workout statistics can be generated for members 1 On the NETWORK DEVICE SELECTION screen Figure A choose either Wired network interface or Wireless network interface depending on how the PCTV screen will be connecting to the Internet NOTE If there is not a wireless connection present only a Wired network interface will be seen as a choice Figure B Click NEXT NETWORK DEVICE SELECTION kakai als meee dieve us Ree kas namam The faitowira devices are ivall li Aired network interface WiIireleads networke interface TWAiPod only Moa network connection ie CL FIGURE A NETWORK DEVICE SELECTION Which meterork device should be uted Tie ll hmg devir oe av lloblu Wired network interface TV only Ho n tvork corrector FIGURE B 50 PROGRAMMING THE PCTV 4 3 CONNECTING TO THE NETWORK CONTINUED 2 The next screen will start the process of connecting to the network Touch TEST NETWORK to make sure that the unit can access the Netpulse Server Figure C SYSTEM PAIRING Pair this devige te the N tpult Authentication Server Pr ts lest Network to confirm connectivity and then inttall to install his unit on the N tpul network au Se tee ton ef thin
53. tified as well as the locations that they should be mounted 2 Once it is determined where the APs are going to be mounted determine where the remaining network equipment will be housed This is often in a secure closet or communications room Once this area is identified plan out the cable runs Each AP will need a home run back to this closet Network cables cannot be split or tapped each run must connect only to a single AP Measure the distance from the communications closet to each access point mounting location This distance cannot be longer than 90 meters 300 If the distance exceeds this limit an IDF intermediary distribution frame will need to be installed which houses an additional network switch to act as a repeater for the signal Once all the runs are planned out pull terminate and test all of the cable runs to the AP mounting locations 3 Once cable has been pulled the access points are ready to be mounted The following section covers the propagation patterns of the APs and the appropriate ways to mount them Both the MR12 and the MR24 have virtually identical coverage patterns The coverage patterns are shown below and on the next page Signal overag Patterns 1 a ati Ey Ayla um aoe a ee J 475 4 ee aa a js TT FI NETWORK CONFIGURATION amp SETUP 2 2 SETTING UP A WIRELESS NETWORK CONTINUED tr Both the 2 4GHz and 5 GHz patterns are fairly symmetric in the azimuthal plane XY s
54. ting Workout History NOTE It is extremely important that the machine is tested and ensure that workout statistics are being generated 1 Start using the equipment Use the equipment for at least a minute 2 Touch END WORKOUT to generate workout statistics NOTE A user must be on one of the entertainment screens in order to end the workout 3 Ensure that statistics are being generated 55 SETTING UP A USER PROFILE 5 1 SETTING UP A USER PROFILE Each user can set up a personal User Profile or workout as a guest Push the GO key on the Attract Screen Figure A MATRIX Netpulse FIGURE A To workout as a guest without setting up or entering a user ID press CONTINUE WITHOUT REGISTERING Figure B To create a new user profile push NEW USER Figure C FIGURE B FIGURE C 1 Use the on screen number pad to create a user ID The ID should be easy to remember and can be up to 10 numbers long Phone numbers are good for this Figure D Push NEXT 2 Use the on screen key board to enter an e mail address Neither Matrix Fitness nor Netpulse share personal information Figure E Push NEXT R Vser D nary l m ja caer g go T i vau ui renpiu g cele eee sel re ER Pei sm ij a x Tili i i on a Oe a FIGURE D FIGURE E 56 SETTING UP A USER PROFILE 5 1 SETTING UP A USER PROFILE CONTINUED 3 Use the on screen keys to Choose an Image Password Figure F ke
55. ts wireless coverage Do not mount APs to ceilings that are higher than 25 or there will not be sufficient coverage to the equipment If the facility s ceilings are higher than 25 consider mounting the AP on a nearby wall illustrated later in this document e Understand and plan around interference There are two main types of interference a facility needs to be concerned about The first is physical interference Physical objects that block line of sight to the access point will interfere with the signal This includes walls windows pillars shelving lighting air ducting etc Try to pick mounting locations that allow for clear line of sight to the equipment It may be necessary to use a drop pole to lower the AP below these types of obstructions The second type of interference is electrical and magnetic interference This includes other wireless and radio frequency devices such as neighboring access points cordless phones baby monitors and two way radios It also includes other devices that emit EMI electromagnetic interference such as microwaves high voltage power lines electrical distribution boxes fluorescent lighting ballasts generators and any other electrical devices that turns currents on and off at high speeds Avoid running network cable and mounting APs near these sources of interference f Once all of the above factors have been taken into consideration the number of access points needed should be able to be iden
56. ug the controller wire into the port titled PCTV Figure L ne il FIGURE K FIGURE L 13 If the system is wired plug the net wire yellow from the TV Bracket kit into the Ethernet port in the back of the PCTV Figure M If the sys tem is wireless skip this step FIGURE M 14 If the PCTV is wireless plug the wireless dongle into the USB port on the back of the PCTV Figure N and use the double sided tape to secure the dongle to the PCTV plastics Figure O FIGURE N FIGURE O 31 BRACKET INSTALLATION amp CONSOLE SETUP 3 5 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LMM CONSOLE CONTINUED 15 Install the PCTV to the TV mounting bracket using the 4 screws shipped in the back of the PCTV Figure P 16 Run the coax cable from the TV bracket to the back of the PCTV and screw it in Figure Q FIGURE P FIGURE Q 17 Plug the TV power wire from the console mast into the TV power wire from Step 6 Both wires are labeled TV Figure R 18 Plug the controller wire from the TV bracket kit into the C Safe Board near the top of the console Figure S gt n FIGURE R FIGURE S 19 If the system is wired plug the Net Wire from Step 13 into the 8 pin connector coming up the console mast with the console cable Figure T If the system is wireless skip this step FIGURE T 32 BRACKET INSTALLATION amp CONSOLE SETUP 3 5 PCTV BRACKET INSTALLATION amp CONSOLE SETUP T3x LMM CONSO
Download Pdf Manuals
Related Search