For Sales, Service, and Parts Contact ESCO at 1-800-352-9852
Contents
1. and swing wheel W away from the wheel Pull back the unit Safety instruction MANOEUVRING WITH WHEEL LOAD 1 Ensure that the small support wheel W is supporting the wheel load correctly 2 Ensure that the locks M L and S are in locked position WARNING Safety instructions Make sure that lifting only occurs on a flat and strong surface floor The wheel load must be lifted in a vertical angle as the wheel load might otherwise slide on the rollers away from the unit causing the unit to move towards the operator Do not overload the unit Overloading with loads over 1500 kg could result in damage to the unit or in worst case cause other damage and even accidents Lowering a load of more than 1500 kg onto the unit may lead to serious damage to the unit Example If the operator lowers the vehicle itself before lowering and moving the wheel dolly away from the vehicle Before lifting transporting a load the operator MUST take precautions that the load is not allowed to drop and that the weight distribution is safe The operator must before use take precautions that all pins are safely locked with split pins or lock rings ATTENTION The LOAD must be blocked with the guide arm K locked and W in correct position to support the wheels on the opposite side Always lower the load to the lowest possible position before transportation Important The safety valve is calibrated and sealed by the manufacturer and it is ABSOLUTELY PR2. precautions that repair is made by a skilled person Before every use the operator must take precautions that there are no visible faults such as leaks damage of the WD and loose or missing parts In case the operator suspects that the unit has been overloaded or wrongly loaded it must before further use be inspected by a skilled person or an authorized Oil DO NOT use brake fluid motor oil etc Volume 0 6 litres Type Use only hydraulic oil with a gradation viscosity of AWS22 Compac recommends Castrol In case the hydraulic unit has a lack of oil or has been taken apart in order to replace the seals then fill up with the correct oil quantity Activate the pump handle and add oil slowly through the filling hole at the plug The lifting arms must be in minimum position as close together as possible when refilling oil Warning Too much oil quantity might cause problems to the hydraulic system Decommissioning If the unit should ever be scrapped draw off the oil into an approved container and dispose it at an approved authority 10 07 2007 GB VL WD 1500 cs 3459 xoz 0006 3461A BIL WD1500 G3 No DANSK DEUTSCH ENGLISH FRANGAIS 140 Skrue Schraube Screw Vis 206 Split Splint Split pin Goupille 828 Fitting Fitting Fitting Raccord 1144 Skrue Rietstockschraube Pointed screw Vis pointue 1208 Trykfjeder Feder Spring Ressort 1314 Skive Scheibe Washer Rondelle 1324 Spzendstift Spannstift Elastic pin Gou
3. 3 af 3483 it 1 EE No DANSK DEUTSCH ENGLISH FRAN AIS 500 Skrue Schraube Screw Vis 1627 O ring O ring O ring Joint torique 3046 L sem trik Mutter Nut Ecrou 3417 Skrue Schraube Screw Vis 3442 Skrue Schraube Screw Vis 3467 O ring O ring O ring Joint torique 3468 Skrabering Abstreifring Scraper ring Segment racieur 3469 T tningsring Oldichtungsring Ringtoil Anneaux de joint 3477 Pedais t svejst Fusshebel geschwei t Pedal set welded P dale soud 3480 Ventilhus Ventilgen use Valve housing Corps de soupapes 3481 Glider Schieber Saddie support Support pour selie 3482 Endeplade Blech Cover Plaque 3483 Las Schiess Lock Arr t 3484 Pieilstang Schubstange Connectingrod Bielie de manoeuvre 60502 Reparations s t Dichtunassatz Repair kit Jeu de r paration indehoidt I Reparations s t 3464 3470 udgave3 im Dichtungsatz enthalten Contained in the repair kit Contenu dans le jeu de Joint 2007 1 L Q 3402 A B gt 2007 10 31 969 120 2007 11 01 gt 3498j2508 No DANSK DEUTSCH ENGLISH FRANCAIS 15 Olieprop lverschraubung Oil plug Bouchon dhuile 17 Ventilprop Ventilschraube Valve plug Bouchon de valve 18 Kobberring Kupferring Copper ring Anneau de cuivre 19 Kugle Kuge Bal Bille 20 Ventilprop Ventilschraube Valve plug Bouchon de vaive T Oliet tningsring ldichtungsring Ring oil Anneaux de joint 112 Pakdase Stopfbuchse Stuffing box Ecrou de piston bie Pakning Di
4. OHIBITED to open the seal or adjust its calibration Offence against the above safety instructions could in worst case result in loss of the load which could cause personal injury and or damage to the unit or properties In case the unit has any irregularities which could affect the safety the unit must not be operated until it has been repaired The unit should not be used if there are any oil leakages or if the unit seems different to use than when it was new In such cases the unit should be inspected repaired by a skilled person More information on spare parts etc is available on www compac eu under Services The manufacture is not liable for wrong use changes to the construction use of other spare parts than original or adjustments repairs by unauthorised persons Safety Maintenance Inspection of the unit must only be done without load for safety reasons Only authorized skilled personnel may repair adjust the unit Use only original parts For adjustment follow the instructions of the manufacturer For further information please contact www compac eu Maintenance At normal use all mechanical moving parts only requires a monthly lubrication to be maintained The pins must be greased every three months Important Use only oil or grease free from acid An annual inspection must be performed by a skilled person Every eventually wearing out or defective part must be replaced with original spare parts The owner and or user must take
5. ating instruction The unit is operated by moving the foot pedal E into lifting or lowering position and afterwards pumping the pump handle P Labelling Warning and CE approval labels are fitted onto the unit Make sure that lifting only occurs on a The wheel load must be lifted in a vertical flat and strong surface floor angle as the wheel load might otherwise slide on the rollers away from the unit causing the unit to move towards the operator Mounting After opening the packaging check the unit for visible damage leakage etc Please recycle or use the packing material again Safety instructions LIFTING 1 7 Make sure that lifting only occurs on a flat and strong surface floor If not lifting with this unit is prohibited due to risk of danger damages The wheel load should be lifted from the floor Place the rollers F on either side of the wheel that should be lifted Move the unit as close to the wheel load as possible Loosen the vertical support arm H and horizontal support arm A By using grip K it is possible to steer the arm with the small support wheel W to the opposite side of the wheel load Once the small support wheel W is on the opposite side it can be steered behind the wheel load This will prevent the wheel load from dropping to the opposite side during manoeuvring Once you have placed the guide arm A correctly lock its position with the lock M I Lock L should be o
6. chtung Packing Joint 114 Returspindel Ablaf3spindel Return spindie Prvot de retour VAS Fjeaer Feder Spring Ressort 116 M trik Mutter Nut Ecrou AT Kugle Kuge Ball Bille 120 L sering Seegerring Lock ring Circlips 129 Pieilstang Schubstanae Connecting rod Bielle de manoeuvre 393 Nagle Nage Shaft Rivet 529 O ring O ring O ring Joint torique 959 Pumpestempel Pumpenkolben Pump piston Piston ae pompe 960 Manchet Manschette Sleeve Bague 961 St ttering Buchse Back up ring Anneau d aspiration 962 L sering Seegerring Lock ring Circlips 965 Pakdase Stopfbuchse Stuffing box Ecrou de piston 966 O ring O ring O ring Joint torique 969 Nagle Nagel Shaft Rivet 2415 Overtryksventil kompiet Uberdruckventil komplet Excess pressure valve Soupape de surpression 2608 Split Splint Split pin Goupille fendue 2935 Stift Splint Pin Chevilie 3401 Pumpehus kompiet Pumpengeh use komplett Pump hausing complete Corps de pompe complet 349 Nagie Nagel Shaft Rivet 60501 Reparations s t Dichtungssatz Repair kit Jeu de r paration s indeholdt i Reparations Im Dichtungssatz enthalten Contained in the repair kit Contenu aans le jeu de s t joint 3402 2007 10 25
7. efoulment co 3472 Trykr r Druckrohr Pressure pipe Tuyau de refoulment 3473 Pumpearm komplet Pumpenarm komplett Fulcrum arm complete Levier de pompage com 3474 Trykr r Druckrohr Pressure pipe Tuyau de refoulment 3475 Trykr r Druckrohr Pressure pipe Tuyau de refoulment 3485 Hus f L s Geh use Housing Corps 3486 L setap Zapfen Pin Cliquet de rr t 3487 Knop f L s Handgriff Handle Manche 3488 Sk rm Blech Sheet Plaque 3489 Hus f bremse Geh use Housing Corps 3492 Skrue Schraube Screw Vis 3496 Hjul m bremse komplet Rad mit bremsen komplett Wheel w breakes compl Frain pour roue compl te 3497 Hjul komplet Rad komplett Wheel complete Roue compl te OAL006 Skilt Abseichen Badge Insigne 0CC028 Nagle Bolzen Shaft Rivet No DANSK DEUTSCH ENGLISH FRANCAIS 3407 Manchet Manschette Sleeve Bague 3408 Manchet Manschette Sleeve Bague 3448 Pakdase Stopfbuchse Stuffing box Ecrou de piston 3455 Sikringsring Sicherneitsring Safety ring Pousseur rondelle 3462 Stempel komplet Kolben komplett Piston complete Piston complet 3463 Cylinder svejst Zylinder geschwei t Cylinder welded Cylindre soud 3468 Skrabering Abstreifring Scraper ring Segment racleur 3495 Kobberring Kupferring Copper ring Anneau en cuivre 60500 Reparations s t Dichtungssatz Repair kit Jeu de r paration r Indeholdt i Reparations Im Dichtungssatz enthalten Contained in tne repair kit Contenu dans le jeu de s t joint 3470 Pwe HS e
8. es ESCO ESCO 90538 For Sales Service and Parts Contact ESCO at 1 800 352 9852 Instruction manual Compac wheel dolly model WD1500 Important Read and understand the instruction before use Operating and service manual for wheel dolly model WD 1500 Max Capacity 1500 kg Instruction and responsibility This instruction and safety manual must be enclosed with the wheel dolly at all times It is very important that the owner and the operator completely understand the operating safety and maintenance instructions before use The manufacturer is not liable for wrong or irresponsible use or maintenance due to the operators not knowing and following these instructions If the operator is not fluent in English then these instructions and warnings shall be read and explained to the operator in the operator s native language making sure that he understands its contents How to use the wheel dolly WD1500 is a mobile wheel dolly for demounting and mounting large wheels with an outside diameter of 1150 mm up to 2150 mm 84 The wheel load is lifted when the 2 x 4 rollers press horizontally on each side of the wheel Lifting will require more force in the beginning as the rollers are pressing against each other Lifting occurs with pumping the handle P Lowering the wheel load is activated by moving the foot pedal E into the opposite position The pump handle P can then be used for lowering the wheel load again Oper
9. pen while lifting or lowering so that the wheel W supports the wheel load on the opposite side Kindly note that you should NOT lock position L Once you begin lifting the wheel load lock L must be open as this will allow the guide arm to follow the upwards and downwards movement of the wheel as it is raised and lowered The lifting can now start Before you end the lifting procedure active safety pin S so that the manual safety stop is activated should a hydraulic leak occur After a short lifting or lowering action the safety pin S will be activated The safety pin is spring loaded and will lock the movement of the lifting arms To unlock the safety stop pump a little in the opposite direction so that the safety pin S can be pulled up again Safety instruction LOWERING MOUNTING OF WHEEL 1 Release the safety pin S 2 Inspect that the small wheel W has a firm grip on the wheel load before lowering 3 Before lowering the wheel load make sure that vertical guide lock L is released and free to move 4 Once you slowly start lowering the wheel load the guide arm L should be able to freely follow the movement of the wheel If not the risk is that the wheel will drop away from its support W on the opposite side of the wheel and could thereby accidentally fall 5 Activate the pump lever P to lower the load or reach the correct mounting height 6 Once the unit can be removed from the wheel load release locks K
10. pille de serrage 1421 Skrue Schraube Screw Vis 1540 Fitting Fitting Fitting Raccord 1711 Oliebremse Senkbremse Oil valve Frein d huile 2067BL Hjul Rad Wheel Roue 2185 Fitting Fitting Fitting Raccord 2641 Megtrik Mutter Nut Ecrou 2802 Mgtrik Mutter Nut Ecrou 2934 Bolt Bolzen Bolt Boulon 3036 Fjedersplit Splint Split pin Goupille 3046 L sem trik Mutter Nut Ecrou 3064 Skrue Schraube Screw Vis 3076BL Plastprop KunststoffverschluB Cap Bouchon 3192 Skrue Schraube Screw Vis 3384 L sering Seegerring Lock ring Circlips 3402 Pumpe komplet Pumpe komplett Pump complete Pompe compl te 3440 Kugle handtag Kugel Ball Bille 3441 Handtag Handgriff Handle Manche 3443 Skrue Schraube Screw Vis 3444 Skrue Schraube Screw Vis 3446 Rulle Rolle Roller Poulie 3453 Aksel Achse Shaft Axe 3454 B sning Buchse Bushing Manchon 3456 Stop f cylinder Halt Stop Arr t 3457 Trykr r Druckrohr Pressure pipe Tuyau de refoulment 3458A T rn teleskop Zwinger teleskop Tower telescope Chateau t lescope 3459 St tter r komplet St rtz Rohr komplett Supporting pipe compl Support de Tuyau compl 3460 Rulleoph ng komplet Chassis komplett Chassis complete Ch ssis compl te 3461A T rn Zwinger Tower Chateau 3464 Cylinder komplet Zylinder komplett Cylinder complete Cylindre compl te 3470 Omskiftventil komplet Ventil komplett Valve complete Soupape compl te 3471 Trykr r komplet Druckrohr komplett Pressure pipe complete Tuyau de r
Download Pdf Manuals
Related Search