INSTALLATION & OPERATION MANUAL - Garland
Contents
1. SECTION 3 PREVENTATIVE MAINTENANCE aaa ae ee PREVENTATIVE MAINTENANCE The dishmachines covered in this manual are designed to operate with a minimum of interaction with the operator However this does not mean that some items will not wear out in time Jackson highly recommends that any maintenance and repairs not specifically discussed in this manual should be performed by QUALIFIED SERVICE PERSONNEL ONLY Performing main tenance on your dishmachine may void your warranty if it is still in effect so if you have a question or concern do not hesitate to contact one of the QUALIFIED SERVICE AGENCIES listed in the back of this manual There are many things that operators can do to prevent catastrophic damage to the dishmachine One of the major causes of component failure has to do with prescrapping procedures A dishmachine is not a garbage disposal any large pieces of mate rial that are put into the machine shall remain in the machine until they are either broken up after spreading out on your ware or physically removed Strainers are installed to help catch debris but they do no good of they are clogged Have operators regularly inspect the pan strainers to ensure 1 that they are free of soil and debris and 2 they are laying flat in the tub When cleaning out strainers do NOT beat them on waste cans The strainers are made of metal and can be forgiving but once severe damage is done it is next to impossible for the2. 1 CIRCULATOR PUMP R1 CONTROL RELAY WASH MOTOR CONTACTOR R3 WASH TEMPERATURE RELAY R4 CIRCULATOR PUMP RELAY TM TIMER MOTOR Ci CYCLE SWITCH AUTO START RESET SWITCH SWITCHES VOLTABE WASH CYCLE SWITCH CONNECTION C4 RINSE FILL SWITCH 51 POWER SWITCH s DOOR SWITCH 3 NORMAL DELIME SWITCH El POWER LIGHT E2 CYCLE LIGHT FS FILL SOLENOID TS WASH THERMOSTAT SWITCH WL WATER LEVEL CONTROL HP HIGH LEVEL PROBE CONSTANT VOLTAGE CONNECTION SF SWITCHED VOLTAGE CONNECTION RF RINSE CONNECTION 30 DF DETERGENT CONNECTION CONTROL BOX LAYOUT BLU RINSE AID DISPENSER CONNECTION WHT YEL a ORG BLK BLK ORG BLK ORG WHT SECONDS CYCLE RESET MICRO AUTOSTART RESET MICRO WASH CYCLE MICRO RINSE MCCRO 9903 002 56 891 Jackson Enodis One Enrepara SECTION 4 ELECTRICAL SCHEMATICS TEMPSTAR GPX 208 230 VOLT 50 60 HERTZ SINGLE PHASE Le Re O 8 che St 2 DETERGENT DISPENSER CONNECT ON CONSTANT VOLTAGE e 1119 POWER DISTRIBUTION BLOCK GND GROUND mp Ren 1 WASH PUNP MOTOR 1 CIRCULATOR PUMP R1 CONTROL RELAY Re WASH MOTOR CONTACTOR R3 WASH TEMPERATURE RELAY R4 CIRCULATOR PUMP RELAY TM TIMER MOTOR C1 CYCLE SWITCH Ce AUTO START RESET SWITCH SWITCHED VOLTAGE WASH CYCLE SWITCH CONNECTION c4 RINSE FILL SWITCH 1 POWER SWITCH s2 DOOR SWITCH 5
3. GCS SERVICE INC 696 LARCH AVENUE ELMHURST IL 60126 630 941 7800 800 942 9689 FAX 630 941 6048 GCS SERVICE INC 9722 REAVIS PARK DRIVE ST LOUIS MO 63123 314 683 7444 800 284 4427 FAX 314 638 0135 INDIANA GCS SERVICE INC 5310 E 25TH STREET INDIANAPOLIS IN 46218 317 545 9655 800 727 8710 FAX 317 549 6286 IOWA GOODWIN TUCKER GROUP 3509 DELAWARE AVENUE DES MOINES IA 50313 515 262 9308 800 372 6066 FAX 515 262 2936 goodwintuc aol com IOWA cont CONES REPAIR SVC 1056 27TH AVENUE SW CEDAR RAPIDS IA 52404 319 365 3325 800 747 3326 FAX 319 365 0885 KANSAS GCS SERVICE INC 6107 CONNECTICUT KANSAS CITY MO 64210 816 920 5999 800 229 6477 FAX 816 920 7387 KENTUCKY CERTIFIED SERVICE CENTER 127 DISHMAN LANE BOWLING GREEN KY 42101 270 783 0012 877 907 0012 FAX 270 783 0058 CERTIFIED SERVICE CENTER 1051 GOODWIN DRIVE LEXINGTON KY 40505 606 254 8854 800 432 9269 FAX 606 231 7781 jatkins certifiedsc com GCS SERVICE INC 1002 NANDINO BLVD LEXINGTON KY 40511 606 255 0746 800 432 9260 FAX 606 255 0748 CERTIFIED SERVICE CENTER RAMCO BUSINESS PARK 4283 PRODUCE ROAD LOUISVILLE KY 40218 502 964 7007 800 637 6350 FAX 502 964 7202 cwalker certifiedsc com droenigk certifiedsc com GCS SERVICE INC 4204 SOUTH BROOK STREET LOUISVILLE KY 40214 502 367 1788 800 752 6160 FAX 502 367 0400 LOUISIANA B
4. TABLE OF CONTENTS Section Description Page 1 SPECIFICATION INFORMATION Specifications of the Tempstar GPX 2 Specifications of the Tempstar HH GPX 3 Dimensions for the Tempstar GPX 4 Dimensions for the Tempstar HH GPX 5 Table Dimensions 6 IL INSTALLATION OPERATION INSTRUCTIONS Installation Instructions 8 Electrical Installation Instructions 9 Gas Booster Heater Connection 10 Operation Instructions 12 PREVENTATIVE MAINTENANCE 14 SCHEMATICS 115 Volt 50 60 Hertz Single Phase Tempstar GPX 17 208 230 Volt 50 60 Hertz Single amp Three Phase Tempstar GPX 18 115 Volt 50 60 Hertz Single Phase Tempstar HH GPX 19 208 230 Volt 50 60 Hertz Single amp Three Phase Tempstar HH GPX 20 v JACKSON MAINTENANCE 8 REPAIR CENTERS 21 Jackson Enodis One 1 Salinirnis SECTION 1 SPECIFICATION INFORMATION SECTION 1 SPECIFICATION INFORMATION SPECIFICATIONS OF THE TEMPSTAR GPX PERFORMANCE CAPABILITIES OPERATING CAPACITY RACKS HOUR RACKS PER HOUR DISHES PER HOUR GLASSES PER HOUR OPERATING CYCLE SECONDS WASH TIME RINSE TIME DWELL TIME TOTAL CYCLE TIME TANK CAPACITY GALLONS WASH TANK MINIMUM WASH PUMP CAPACITY GALLONS PER MINUTE 57 1425 1425 45 11 60 8 0 150 ELECTRICAL REQUIREMENTS WASH PUMP MOTOR HP 3 4 RECIRCULATOR PUMP MOTOR HP 1 8 NOTE Typical Electrical Circuit is based upon 1 125 of the full amperage load of the machine and 2 ty
5. NY 13088 315 435 0709 800 371 5921 FAX 315 453 1412 1 8 COMMERCIAL PARTS amp SVC 7387 PITTSFORD VICTOR RD ROCHESTER NY 14610 716 461 2370 800 458 4198 FAX 716 461 5545 NORTH CAROLINA AUTHORIZED APPLIANCE SERVICE CENTER 1020 TUCKASEEGEE RD CHARLOTTE NC 28208 704 377 4501 800 532 6127 FAX 704 377 4504 WHALEY FOODSERVICE 203 D CREEK RIDGE RD GREENSBORO NC 27604 336 333 2333 FAX 336 333 2533 Jackson 24 15 One Enrepara SECTION 5 JACKSON MAINTENANCE amp REPAIR CENTERS 2 2 2 22 2 2222 Sa NORTH CAROLINA cont AUTHORIZED APPLIANCE SERVICE CENTER 109 HINTON AVE WILMINGTON NC 28403 910 313 1250 FAX 910 313 6130 WHALEY FOODSERVICE 8334 K ARROWRIDGE BLVD CHARLOTTE NC 28273 704 529 6242 FAX 704 529 1558 info whaleyfoodservice com WHALEY FOODSERVICE REPAIRS 335 105 SHERWEE DRIVE RALEIGH NC 27603 919 779 2266 FAX 919 779 2224 info whaleyfoodservice com WHALEY FOODSERVICE REPAIRS 6418 101 AMSTERDAM WAY WILMINGTON NC 28405 910 791 0000 FAX 910 791 6662 info whaleyfoodservice com NORTH DAKOTA GCS SERVICE INC 2857 LOUISIANA AVENUE N MINNEAPOLIS 55427 612 546 4221 800 345 4221 FAX 612 546 4286 OHIO CERTIFIED SERVICE CENTER 890 REDNA TERRACE CINCINNATI OH 45215 513 772 6600 800 543 2060 FAX 513 612 6600 sbarasch certifiedsc com CERTIFIED
6. 2 WS 2 1 2 4 MINIMUM 25 1 4 3 4 1 2 ROLL TABLE DIMENSIONS CONNECTION TO DISHMACHINE 4 MINIMUM A N TABLE DIMENSIONS STRAIGHT THROUGH INSTALLATION Jackson Enodis One mires Salinin SECTION 2 INSTALLATION OPERATION INSTRUCTIONS SECTION 2 INSTALLATION OPERATION INSTRUCTIONS INSTALLATION INSTRUCTIONS VISUAL INSPECTION Before installing the unit check the container and machine for damage A damaged container is an indi cator that there may be some damage to the machine If there is damage to both the container and machine do not throw away the container The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new undam aged condition However rough handling by carriers or others may result in there being damage to the unit while in transit If such a situation occurs do not return the unit to Jackson instead contact the carrier and ask them to send a representative to the site to inspect the damage to the unit and to complete an inspection report You must contact the carrier within 48 hours of receiving the machine Also contact the dealer through which you purchased the unit UNPACKING THE DISHMACHINE Once the machine has been removed from the container ensure that there are no miss ing parts from the machine This may not be obvious at first If it is discovered that an item is missing contact
7. 5548 800 624 2117 FAX 303 761 5561 johns hawkinscommercial com METRO APPLIANCE SERVICE 1640 S BROADWAY DENVER CO 80210 303 778 1126 800 525 3532 FAX 303 778 0268 metroappls aol com CANADA Garland Commercial Ranges Ltd 1177 KAMATO ROAD MISSISSAUGA ONTARIO L4W 1X4 905 624 0260 800 427 6668 FAX 905 624 0623 Jackson Enodis One Enrepara Salinirnis
8. Place cups and glasses upside down in racks so that they do not hold water during the cycle The dishmachine is meant not only to clean but to sanitize as well to destroy all of the bacteria that could be harmful to human beings In order to do this ware must be properly prepared prior to being placed in the machine DAILY MACHINE PREPARATION Refer to the section entitled PREPARATION at the top of this page and follow the instruc tions there Afterwards check that all of the chemical levels are correct and or that there is plenty of detergent available for the expected workload WARM UP CYCLES For a typical daily start up it may be necessary to run the machine through 3 cycles to ensure that all of the cold water is out of the system and to verify that the unit is operating correctly To cycle the machine ensure that the power is on and that the tub has filled to the correct level Lift the doors and the cycle light will illuminate When the light goes out close the doors the unit will start run through the cycle and shut off automatically Repeat this two more times The unit should now be ready to proceed with the washing of ware WASHING A RACK OF WARE To wash a rack open the doors completely being careful for hot water that may drip from the doors and slide the rack into the unit Close the doors and the unit will start automatically Once the cycle is completed open the door again watching for the dripping hot water and remov
9. SERVICE CENTER 6025 N DIXIE DRIVE DAYTON OH 45414 937 898 4040 800 257 2611 FAX 937 898 4177 dharvey certifiedsc com COMMERCIAL PARTS amp SVC OF COLUMBUS 1150 WEST MOUND STREET COLUMBUS OH 43223 614 221 0057 800 837 8327 FAX 614 221 3622 cont GCS SERVICE INC 2830 JOHNSTON RD COLUMBUS OH 43219 614 476 3225 800 282 5406 FAX 614 476 1196 ELECTRICAL APPLIANCE REPAIR SVC 5805 VALLEY BELT ROAD CLEVELAND OH 44131 216 459 8700 800 621 8259 FAX 216 459 8707 tomr electapplrep com OKLAHOMA HAGAR RESTAURANT EQMT 1229 W MAIN STREET OKLAHOMA CITY OK 73106 405 235 2184 800 445 1791 FAX 405 236 5592 OREGON RON S SERVICE 16364 SW 72ND AVE PORTLAND OR 97224 503 624 0890 800 851 4118 FAX 503 684 6107 Irobinson ronsservice com PENNSYLVANIA 5 COMMERCIAL PARTS 4 SERVICE 1816 WEST 26TH STREET ERIE PA 16508 814 456 3732 800 332 3732 FAX 814 452 4843 aiserie aol com ELMER SCHULTZ SVC 540 NORTH 3RD STREET PHILADELPHIA PA 19123 215 627 5400 FAX 215 627 5408 elmer2 erols com amp D PARTS amp SERVICE 1833 41 N CAMERON STREET HARRISBURG PA 17103 717 236 9039 800 932 0503 FAX 717 238 4367 PENNSYLVANIA cont AMERICAN KITCHEN MACHIN ERY amp REPAIR 204 QUARRY STREET PHILADELPHIA PA 19106 215 627 7760 800 848 7760 FAX 215 627 1604 GCS SERVICE INC 817 N THIRD STREET P O BOX 35
10. TOTAL CYCLE TIME SELECTION D WASH TIME RINSE TIME DWELL TIME TOTAL CYCLE TIME TANK CAPACITY GALLONS WASH TANK MINIMUM WASH PUMP CAPACITY GALLONS PER MINUTE 53 1325 1325 45 15 60 103 15 120 163 15 180 283 15 300 8 0 150 SPECIFICATIONS OF THE TEMPSTAR HH GPX ELECTRICAL REQUIREMENTS WASH PUMP MOTOR HP 2 0 RECIRCULATOR PUMP MOTOR HP 1 8 NOTE Typical Electrical Circuit is based upon 1 125 of the full amperage load of the machine and 2 typical fixed trip cir cuit breaker sizes as listed in the NEC 2002 Edition Local codes may require more stringent protection than what is dis played here Always verify with your electrical service con tractor that your circuit protection is adequate and meets all applicable national and local codes These numbers are pro vided in this manual simply for reference and may change without notice at any given time RINSE TYPICAL HEATER TOTAL ELECTRICAL VOLTS PH HZ RATINGS AMPS CIRCUIT 110 120 1 60 N A 24 30 AMP 208 240 1 60 N A 7 15 AMP WATER REQUIREMENTS INLET TEMPERATURE BOOSTER OUTPUT BTU LESS THAN 60 F 200 000 60 110 F 100 000 140 F 60 000 WASH TEMPERATURE MINIMUM 150 F RINSE TEMPERATURE MINIMUM 180 F GALLONS PER HOUR 72 0 WATER LINE SIZE NPT MINIMUM 1 2 DRAIN LINE SIZE NPT MINIMUM 1 1 2 FLOW PRESSURE NPT 20 5 NOTE Always refer to the machine data plate for specific electrical and water requirements Th
11. component is not present on your machine Do not confuse static pressure with flow pressure Static pressure is the line pressure in a no flow condition all valves and services are closed Flow pressure is the pressure in the fill line when the fill valve is opened during the cycle It is also recommended that a shock absorber not supplied with the Tempstar models be installed in the incoming water line This prevents line hammer hydraulic shock induced by the solenoid valve as it operates from causing damage to the equip ment WATER CONNECTION TO THE GAS BOOSTER HEATER Refer to page entitled GAS BOOSTER HEATER CONNEC TIONS Jackson Enodis One Enrepara mies Salinirnis SECTION 2 INSTALLATION OPERATION INSTRUCTIONS E INSTALLATION INSTRUCTIONS GAS BOOSTER HEATER ELECTRICAL INSTALLATION The gas booster heater must have a separate electric hookup than that supplied to the dishmachine Please refer to the manual supplied with your gas booster heater GAS CONNECTION TO THE BOOSTER HEATER Please refer to the manual supplied with your gas booster heater VENTILATION OF THE GAS BOOSTER HEATER Please refer to the manual supplied with your gas booster heater PLUMBING CHECK Slowly turn on the water supply to the machine after the incoming fill line and the drain line have been installed Check for any leaks and repair as required All leaks must be repaired prior to placing the machine in operation EL
12. 21 858 549 8411 800 422 7278 FAX 858 549 2323 P amp D APPLIANCE SVC 100 SOUTH LINDEN AVE S SAN FRANCISCO CA 94080 650 635 1900 800 424 1414 FAX 650 635 1919 pndappl aol com COLORADO HAWKINS COMMERCIAL APPLIANCE SERVICE 3000 S WYANDOT ST ENGLEWOOD CO 80110 303 781 5548 800 624 2117 FAX 303 761 8861 cont METRO APPLIANCE SERVICE 1640 S BROADWAY DENVER CO 80210 303 778 1126 800 525 3532 FAX 303 778 0268 metroappls aol com CONNECTICUT GCS SERVICE INC 302 MURPHY ROAD HARTFORD CT 06114 860 549 5575 800 423 1562 FAX 860 527 6355 DELAWARE AMERICAN KITCHEN MACHIN ERY amp REPAIR 204 QUARRY STREET PHILADELPHIA PA 19106 215 627 7760 800 848 7760 FAX 215 627 1604 GCS SERVICE INC 817 N THIRD STREET PHILADELPHIA PA 215 925 6217 800 441 9115 FAX 215 925 6208 ELMER SCHULTZ SERVICE 36 BELMONT AVE WILLMINGTON DE 19804 302 655 8900 800 225 0599 FAX 302 656 3673 elmer2 erols com EMR SERVICE DIVISION 106 WILLIAMSPORT CIRCLE SALISBURY MD 21804 410 543 8197 FAX 410 548 4038 FLORIDA COMMERCIAL APPLIANCE SVC 8416 LAUREL FAIR CIRCLE BLDG 6 SUITE 114 TAMPA FL 33610 813 663 0313 800 282 4718 FAX 813 663 0212 commercialappliance worldnet at t net FLORIDA cont GCS SERVICE INC 3373 N W 168TH STREET MIAMI FL 33056 305 621 6666 800 766 8966 FAX 305 621 6656 GCS SER
13. 3 NORNAL DELIME SWITCH El POWER LIGHT Ee CYCLE LIGHT FS FILL SOLENOID 15 WASH THERMOSTAT SWITCH WL WATER LEVEL CONTROL HP HIGH LEVEL PROBE CF CONSTANT VOLTAGE CONNECTION SF SVITCHED VOLTAGE CONNECTION RF RINSE AID CONNECTION DF DETERGENT CONNECTION CONTROL BOX LAYOUT LUE RINSE ALD DISPENSER CONNECTION WHT YEL Q p ayau TS lt 2 ORG BLK BLK DRG BLK ORG REJ a 9905 DD2 56 900 Jackson Enodis One Enrepara Salinirnis 18 SECTION 4 ELECTRICAL SCHEMATICS TEMPSTAR HH GPX 115 VOLT 50 60 HERTZ SINGLE PHASE BNI LEGEND 8 DF DETERGENT 5 LIN POWER DISTRIBUTION BLOCK CONNECTION GND CHASSIS GROUND M1 WASH PUMP MOTOR CONSTANT VOLTAGE 1 CIRCULATOR PLIMP CONNECTION R1 CONTROL RELAY WASH MOTOR CONTACTOR R3 WASH TEMPERATURE RELAY 51 POWER SWITCH 52 DOOR SWITCH 53 NORMAL DELIME SWITCH 4 CYCLE SELECTOR SWITCH 1 55 CYCLE SELECTOR SWITCH 2 56 CYCLE SELECTOR SWITCH 3 57 CYCLE SELECTOR SWITCH 4 C1 CYCLE SWITCH Ce AUTO START RESET SWITCH WASH CYCLE SWITCH RINSE FILL SWITCH 1 POWER LIGHT Ee CYCLE LIGHT FS FILL SOLENOID HP HIGH LEVEL PROBE TS WASH THERMOSTAT SWITCH TM TIMER MOTOR WL WATER LEVEL CONTROL WCT WASH CYCLE TINER CF CONSTANT VOLTAGE CONNECTION SF SWITCHED VOLTAGE CONNECTION RF RINSE AID CONNECTION DF DETERGENT CONNECTION COMPONENT LAYOUT RINSE AJO BCSPENSER CONNECTION 9905 002 57 6la Jackson Enod
14. 4588 GCS SERVICE INC 748 FESSLERS LANE NASHVILLE TN 37210 615 244 8050 800 831 7174 FAX 615 244 8885 TEXAS GCS SERVICE INC AUSTIN TX 800 822 2303 ARMSTRONG REPAIR CENTER 1700 S LAMAR BLVD 327 AUSTIN TX 78704 512 416 1101 800 392 5322 FAX 512 416 6912 ARMSTRONG REPAIR CENTER 5110 GLENMONT DRIVE HOUSTON TX 77081 713 666 7100 800 392 5325 FAX 713 661 0520 gm armstrongrepair com Jackson Enodis One Enrepara TEXAS cont COMMERCIAL KITCHEN REPAIR CO 1377 N BRASOS P O BOX 831128 SAN ANTONIO TX 78207 210 735 2811 800 292 2120 FAX 210 735 7421 brock commercialkitchen com GCS SERVICE INC 440 WRANGLER DRIVE 100 COPPELL TX 75019 972 906 0307 800 442 5026 FAX 972 906 9886 GCS SERVICE INC HOUSTON TX 800 822 2303 GCS STOVE PARTS 2120 SOLANA STREET FORT WORTH TX 76117 817 831 0381 800 433 1804 FAX 817 834 7754 bud stoveparts com UTAH LA MONICA S RESTAURANT SVC 6182 SOUTH STRATLER AVENUE MURRAY UT 84107 801 263 3221 800 527 2561 FAX 801 263 3229 lamonica81 aol com GCS SERVICE INC 1366 S 400 WEST SALT LAKE CITY UT 84115 801 487 3653 800 955 9201 FAX 801 487 2253 VERMONT NORTHERN PARTS amp SVC 4874 S CATHERINE STREET PLATTSBURGH NY 12901 518 563 3200 800 634 5005 FAX 800 782 5424 info northernparts com GCS SERVICE INC 180 SECOND STREET CH
15. 64 PHILADELPHIA PA 19123 215 925 6217 800 441 9115 FAX 215 925 6208 GCS SERVICE INC 210 VISTA PARK DRIVE PITTSBURGH PA 15205 412 787 1970 800 738 1221 FAX 412 787 5005 RHODE ISLAND GCS SERVICE INC 180 SECOND STREET CHELSEA MA 02150 617 889 9393 800 225 1155 FAX 617 889 1222 SOUTH CAROLINA AUTHORIZED APPLIANCE SERVICECENTER 1811 TAYLOR ST COLUMBIA SC 29202 803 254 8414 FAX 803 254 5146 AUTHORIZED APPLIANCE SERVICECENTER 2249 AUGUSTA RD GREENVILLE SC 29605 864 235 9616 FAX 864 235 9623 WHALEY FOODSERVICE REPAIRS 126 amp US1 P O BOX 4023 WEST COLUMBIA SC 29170 803 791 4420 800 877 2662 FAX 803 794 4630 info whaleyfoodservice com WHALEY FOODSERVICE REPAIRS 748 CONGAREE ROAD GREENVILLE SC 29607 864 234 7011 800 494 2539 FAX 864 234 6662 info whaleyfoodservice com NORTH CAROLINA TO TEXAS SOUTH CAROLINA cont WHALEY FOODSERVICE REPAIRS 1406 C COMMERCE PL MYRTLE BEACH SC 29577 843 626 1866 FAX 843 626 2632 info whaleyfoodservice com WHALEY FOODSERVICE REPAIRS 4740 A FRANCHISE STREET N CHARLESTON SC 29418 843 760 2110 FAX 843 760 2255 info whaleyfoodservice com SOUTH DAKOTA GCS SERVICE INC 2857 LOUISIANA AVENUE N MINNEAPOLIS MN 55247 612 546 4221 800 345 4221 FAX 612 546 4286 TENNESSEE GCS SERVICE INC 3717 CHERRY ROAD MEMPHIS TN 38118 901 366 4587 800 262 9155 FAX 901 366
16. ANA PARTS INC 1501 KUEBLE STREET HARAHAN LA 70123 504 734 0076 800 325 7543 FAX 504 734 8456 LOUISIANA cont BANA PARTS INC 4028 GREENWOOD ROAD SHREVEPORT LA 71109 318 631 6550 800 832 6550 FAX 318 636 5675 MAINE MRE INC 170 JOHN ROBERTS RD UNIT 3 PROTLAND ME 04106 207 772 1152 800 823 9700 FAX 207 772 1445 NORTHERN CROWN SERVICES INC 225 INDUSTRIAL WAY PORTLAND ME 04103 207 797 7333 800 696 7560 FAX 207 696 1128 steve northerncrownservices com richard northerncrownservices com MARYLAND EMR SERVICE DIVISION 700 EAST 25TH STREET BALTIMORE MD 21218 410 467 8080 800 879 4994 FAX 410 467 4191 baltparts emrco com EMR SERVICE DIVISION 106 WILLIAMSPORT CIRCLE SALISBURY MD 21804 410 543 8197 888 687 8080 FAX 410 548 4038 baltparts emrco com EMR SERVICE DIVISION 2626 PITTMAN DRIVE SILVER SPRING MD 20910 301 588 8080 800 348 2365 FAX 301 588 6985 baltparts emrco com GCS SERVICE INC 2660 PITTMAN DRIVE SILVER SPRING MD 20910 301 585 7550 DC 410 792 0338 BALT 800 638 7278 FAX 301 495 4410 IDAHO TO MISSISSIPPI MASSACHUSETTS ACE SERVICE CO 95 HAMPTON AVE NEEDHAM MA 02494 781 449 4220 800 225 4510 MA amp NH FAX 781 444 4789 taceservice aol com MASSACHUSETTS RESTAURANT SUPPLY 34 SOUTH STREET SOMERVILLE MA 02143 617 868 1930 800 338 6737 FAX 617 868 5331 GCS SERVICE INC 180 SECOND STREE
17. DUAL TEMPERATURE GAS HEATED E N 3 d 5 DOOR TYPE DISHMACHINES One Company Countless Solutions INSTALLATION amp OPERATION MANUAL FOR JACKSON MODELS TEMPSTAR GPX TEMPSTAR HH GPX Jackson an Encdis Company Jackson MSC Inc P O BOX 1060 HWY 25E BARBOURVILLE KY 40906 August 06 2007 FAX 606 523 9196 P N 7610 002 57 30 Revision C an MANUFACTURERS WARRANTY ONE YEAR LIMITED PARTS amp LABOR WARRANTY ALL NEW JACKSON DISHWASHERS WARRANTED THE ORIGINAL PURCHASER BE FREE FROM DEFECTS IN MATERIAL OR WORKMANSHIP UNDER NORMAL USE AND OPERATION FOR A PERIOD OF 1 ONE YEAR FROM THE DATE OF PURCHASE BUT IN NO EVENT TO EXCEED 18 EIGHTEEN MONTHS FROM THE DATE OF SHIPMENT FROM THE FACTORY Jackson MSC agrees under this warranty to repair or replace at its discretion any original part which fails under normal use due to faulty material or workmanship during the warranty period providing the equipment has been unaltered and has been properly installed main tained and operated in accordance with the applicable factory instruction manual furnished with the machine and the failure is reported to the authorized service agency within the warranty period This includes the use of factory specified genuine replacement parts purchased directly from a Jackson authorized parts distributor or service agency Use of generic replacement parts may create a hazard and void war ranty certification The l
18. ECTRICAL POWER CONNECTION Electrical and grounding connections must comply with the applicable portions of the National Electrical Code ANSI NFPA 70 latest edition and or other electrical codes Disconnect electrical power supply and place a tag at the disconnect switch to indicate that you are working on the circuit The dishmachine data plate is located on the right side and to the front of the machine Refer to the data plate for machine operating requirements machine voltage total amperage load and serial number To install the incoming power lines remove the control box cover Install 3 4 conduit into the pre punched holes in the back of the control box Route power wires and connect to power block and grounding lug Install the service wires L1 and L2 to the appropriate terminals as they are marked on the terminal block Install the grounding wire into the lug provided and tighten the connections It is recommended that DE OX or another similar anti oxidation agent be used on all power connections VOLTAGE CHECK Ensure that the power switch is in the OFF position and apply power to the dishmachine Check the incom ing power at the terminal block and ensure it corresponds to the voltage listed on the data plate If not contact a qualified ser vice agency to examine the problem Do not run the dishmachine if the voltage is too high or too low Shut off the service break er and mark it as being for the dishmachine Advise all prop
19. ELSEA MA 02150 617 889 9393 800 225 1155 FAX 617 889 1222 SECTION 5 JACKSON MAINTENANCE amp REPAIR CENTERS esses 2 2 22 222 TEXAS TO WYOMING CANADA VIRGINIA DAUBERS INC 7645 DYNATECH COURT SPINGFIELD VA 22153 703 866 3600 800 554 7788 FAX 703 866 4071 daubers aol com GCS SERVICE INC 2660 PITTMAN DRIVE SILVER SPRING MD 20910 301 585 7550 DC 410 792 0388 BALT 800 638 7278 FAX 301 495 4410 GCS SERVICE INC RICHMOND VA 800 822 2303 WASHINGTON RESTAURANT APPLIANCE SVC 7219 ROOSEVELT WAY NE SEATTLE WA 98115 206 524 8200 800 433 9390 FAX 206 525 2890 info restappl com WEST VIRGINIA STATEWIDE SERVICE INC 603 MAIN AVE NITRO WV 25143 304 755 1811 800 441 9739 FAX 304 755 4001 sws3182 aol com WISCONSIN APPLIANCE SERVICE CENTER INC 2439 ATWOOD AVE MADISON WI 53704 608 246 3160 800 236 7440 FAX 608 246 2721 ascmad execpc com APPLIANCE SERVICE CENTER INC 6843 W BELLOIT RD WEST ALLIS WI 53219 414 543 6460 800 236 6460 FAX 414 543 6480 ascmil execpc com WISCONSIN cont APPLIANCE SERVICE CENTER 786 MORRIS AVE GREEN BAY WI 54304 920 496 9993 800 236 0871 FAX 920 496 9927 ascfox execpc com METROPOLITAN SERVICE 3210 LONDON RD EAU CLAIRE WI 54701 715 832 0555 800 848 3945 FAX 715 832 7813 WYOMING HAWKINS COMMERCIAL APPLIANCE SERVICE 300 S WYANDOT ST ENGLEWOOD CO 80110 303 781
20. Jackson imme diately to have the missing item shipped to you LEVEL THE DISHMACHINE The dishmachine is designed to operate while being level This is important to prevent any dam age to the machine during operation and to ensure the best results when washing ware The unit comes with adjustable bullet feet which can be turned using a pair of channel locks or by hand if the unit can be raised safely Ensure that the unit is level from side to side and from front to back before making any connections PLUMBING THE DISHMACHINE All plumbing connections must comply with all applicable local state and national plumb ing codes The plumber is responsible for ensuring that the incoming water line is thoroughly flushed prior to connecting it to any component of the dishmachine It is necessary to remove all foreign debris from the water line that may potentially get trapped in the valves or cause an obstruction Any valves that are fouled as a result of foreign matter left in the water line and any expenses resulting from this fouling are not the responsibility of the manufacturer CONNECTING THE DRAIN LINE The drain for the Tempstar models covered in this manual are gravity discharge drains All piping from the 1 1 2 FNPT connection on the wash tank must be pitched 1 4 per foot to the floor or sink drain All piping from the machine to the drain must be a minimum 1 1 2 NPT and shall not be reduced There must also be an air gap between the ma
21. LL COMPONENTS WITHIN THE DOTTED REGION ARE FOUND WITHIN THE FOOTPRINT OF THE MACHINE ALL OTHER ITEMS ARE INSTALLED AT THE SITE Jackson Enodis One Enrepara 1 Salinirnis SECTION 2 INSTALLATION OPERATION INSTRUCTIONS SS OPERATION INSTRUCTIONS PREPARATION Before proceeding with the start up of the unit verify the following 1 The pan strainer and pump suction strainer are in place and are clean 2 The overflow tube and o ring are installed 3 That the wash and rinse arms are screwed securely into place and that their endcaps are tight The wash and rinse arms should rotate freely GAS BOOSTER HEATER OPERATION For all start up and operation information please refer to the manual supplied with your gas booster heater POWER UP To energize the unit turn on the power at the service breaker The voltage should have been previously verified as being correct If not the voltage will have to be verified FILLING THE WASH TUB TEMPSTAR GPX Ensure that the delime switch is in the NORMAL position and place the power switch into the ON position The Tempstar model should fill automatically and shut off when the appropriate level is reached just below the pan strainer Verify that the drain stopper is preventing the wash tub water from leaking excessively There may be some slight leakage from the drain hole Verify that there are no other leaks on the unit before proceeding any further The wash tub mu
22. T CHELSEA MA 02150 617 889 9393 800 225 1155 FAX 617 889 1222 GCS SERVICE INC 302 MURPHY ROAD HARTFORD CT 06114 860 549 5575 800 723 1562 FAX 860 527 6355 MICHIGAN GCS SERVICE INC 31829 WEST EIGHT MILE ROAD LIVONIA MI 48152 248 426 9500 800 772 2936 FAX 248 426 7555 JACKSON SERVICE COMPANY 3980 BENSTEIN RD COMMERCE TOWNSHIP MI 48382 248 363 4159 800 332 4053 FAX 248 363 5448 MINNESOTA GCS SERVICE INC 2857 LOUISIANA AVENUE N MINNEAPOLIS MN 55427 612 546 4221 800 345 4221 FAX 612 546 4286 MISSISSIPPI GCS SERVICE INC 2815 19TH ANENUE UNIT A GULFPORT MS 39501 228 864 2722 877 964 2722 FAX 228 822 9412 Jackson Enodis One Enrepara Co Sal ninae SECTION 5 JACKSON MAINTENANCE amp REPAIR CENTERS EE MISSISSIPPI TO NORTH CAROLINA MISSISSIPPI cont GCS SERVICE INC 5755 GALLANT DRIVE JACKSON MS 39206 601 956 7800 800 274 5954 FAX 601 956 1200 GCS SERVICE INC 3717 CHERRY ROAD MEMPHIS TN 38118 901 366 4587 800 262 9155 FAX 901 366 4588 MISSOURI GCS SERVICE INC 6107 CONNECTICUT KANSAS CITY MO 64120 816 920 5999 800 229 6477 FAX 816 920 7387 GCS SERVICE INC 9722 REAVIS PARK DRIVE ST LOUIS MO 63123 314 638 7444 800 284 4427 FAX 314 638 0135 KAMMERLIN PARTS amp SVC 1359 SOUTH KINGSHIGHWAY ST LOUIS MO 63110 314 535 2222 FAX 314 535 6205 petek kps s
23. TREET FORT WORTH TX 76117 817 831 0381 800 433 1804 FAX 817 834 7754 bud stoveparts com HAWKINS COMMERCIAL APPLI ANCE SERVICE 300 S WYANDOT STREET ENGLEWOOD CA 80110 303 781 5548 800 624 2117 FAX 303 761 8861 NEW YORK GCS SERVICE INC BROOKLYN NY 11211 800 822 2303 APPLIANCE INSTALLATION AND SERVICE CORP 1336 MAIN STREET BUFFALO NY 14209 716 884 7425 800 722 1252 FAX 716 884 0410 ais worldnet att net B E S T INC 3003 GENESEE STREET BUFFALO NY 14225 716 893 6464 800 338 5011 FAX 716 893 6466 bestserv aol com DUFFY S EQUIPMENT SVC 3138 ONEIDA STREET SAUQUOIT NY 13456 315 737 9401 800 443 8339 FAX 315 737 7132 duffyequip aol com NORTHERN PARTS amp SVC 21 NORTHERN AVENUE PLATTSBURGH NY 12903 518 563 3200 800 634 5005 FAX 800 782 5424 info northernparts com NEW YORK cont JACKSON FASPRAY SVC 155 SARGEANT AVE CLIFTON NJ 07013 973 471 8000 800 356 6740 FAX 973 471 1289 jfs155 aol com ALL ISLAND REPAIR 40 9 BURT DRIVE DEER PARK NY 11729 631 242 5588 800 323 9411 FAX 631 242 6102 1 5 COMMERCIAL PARTS amp SVC 1900 COLLEGE AVENUE ELMIRA HEIGHTS NY 14901 607 734 6072 888 724 7377 FAX 607 734 9294 1 5 COMMERCIAL PARTS amp SVC 13 WESTR MAIN STREET FALCONER NY 14733 716 665 6556 800 552 6556 FAX 716 665 4227 1 S COMMERCIAL PARTS amp SVC 200 SALINA ST SUITE 114 LIVERPOOL
24. VICE INC 3902 CORPORES PARK DR SUITE 350 TAMPA FL 33619 813 626 6044 800 282 3008 FAX 813 621 1174 JONES McLEOD APPLIANCE SVC 854 LAKESIDE DRIVE MOBILE AL 36693 334 666 7278 800 237 9859 FAX 334 661 0223 service jones mcleod com GEORGIA GCS SERVICE INC 3127 PRESIDENTIAL DRIVE ATLANTA GA 30340 770 452 7322 800 334 3599 FAX 770 452 7473 SOUTHEASTERN RESTAURANT SVC 2200 NORCROSS PKWY SUITE 210 NORCROSS GA 30071 770 446 6177 800 235 6516 FAX 770 446 3157 info srs atl com WHALEY FOODSERVICE REPAIRS 109 A OWENS INDUSTRIAL DRIVE SAVANNAH GA 31405 912 447 0827 888 765 0036 FAX 912 447 0826 HAWAII FOOD EQMT PARTS amp SER VICE CO 300 PUUHALE RD HONOLULU HI 96819 808 847 4871 FAX 808 842 1560 fepsco hula net Jackson 15 One Enrepara SECTION 5 JACKSON MAINTENANCE amp REPAIR CENTERS a eee IDAHO RON S SERVICE 703 E 44TH STREET STE 10 GARDEN CITY ID 83714 208 375 4073 FAX 208 375 4402 RESTAURANT APPLIANCE SVC 7219 ROOSEVELT WAY NE SEATTLE WA 98115 206 524 8200 800 433 9390 FAX 206 525 2890 info restappl com ILLINOIS CONES REPAIR SVC 2408 40TH AVE MOLINE IL 61265 309 797 5323 800 716 7070 FAX 309 797 3631 jackb cones com EICHENAUER SERVICES INC 130 S OAKLAND ST DECATUR IL 62522 217 429 4229 800 252 5892 FAX 217 429 0226 esi esiquality com
25. X 334 661 0223 ALASKA RESTAURANT APPLIANCE SVC 7219 ROOSEVELT WAY NE SEATTLE WA 98115 206 524 8200 800 433 9390 FAX 206 525 2890 info restappl com ARIZONA AUTHORIZED COMMERCIAL FOOD EQMT SVC 4832 SOUTH 35TH STREET PHOENIX AZ 85040 602 234 2443 800 824 8875 FAX 602 232 5862 acsboss aol com GCS SERVICE INC PHOENIX AZ 800 822 2303 ARKANSAS BROMLEY PARTS amp SVC 10TH AND RINGO P O BOX 1688 LITTLE ROCK AR 72202 501 374 0281 800 482 9269 FAX 501 374 8352 service bromleyparts com parts bromleyparts com COMMERCIAL PARTS amp SVC 3717 CHERRY ROAD MEMPHIS TN 38118 901 366 4587 800 262 9155 FAX 901 366 4588 CALIFORNIA BARKERS FOOD MACHINERY SERVICES 5367 SECOND STREET IRWINDALE CA 91706 626 960 9390 800 258 6999 FAX 626 337 4541 service barkers com GCS SERVICE INC LOS ANGELES CA 800 822 2303 amp D APPLIANCE 4220 C ROSEVILLE ROAD NORTH HIGHLANDS CA 95660 916 974 2772 800 824 7219 FAX 916 974 2774 INDUSTRIAL ELECTRIC SVC 5662 ENGINEER DRIVE HUNTINGON BEACH CA 92649 714 379 7100 800 4573783 FAX 714 379 7109 GCS SERVICE INC 360 LITTLEFIELD AVE S SAN FRANCISCO CA 94080 650 635 0720 800 969 4427 FAX 650 871 4019 BARKERS FOOD MACHINERY SERVICES 9373 ACTIVITY ROAD G SAN DIEGO CA 92126 858 695 1091 800 995 7955 FAX 858 995 7955 GCS SERVICE INC 9030 KENMAR DR SUITE 313 SAN DIEGO CA 921
26. abor to repair or replace such failed part will be paid by Jackson MSC within the continental United States Hawaii and Canada during the warranty period provided a Jackson MSC authorized service agency or those having prior authorization from the factory performs the service Any repair work by persons other than a Jackson MSC authorized service agency is the sole responsibility of the customer Labor coverage is limited to regular hourly rates overtime premiums and emergency service charges will not be paid by Jackson MSC Accessory components not installed by the factory carry a 1 one year parts warranty only Accessory components such as table limit switch es pressure regulators pre rinse units etc that are shipped with the unit and installed at the site are included Labor to repair or replace these components is not covered by Jackson MSC This warranty is void if failure is a direct result from shipping handling fire water accident misuse acts of god attempted repair by unau thorized persons improper installation if serial number has been removed or altered or if unit is used for purpose other than it was origi nally intended TRAVEL LIMITATIONS Jackson MSC limits warranty travel time to 2 two hours and mileage to 100 one hundred miles Jackson MSC will not pay for travel time and mileage that exceeds this or any fees such as those for air or boat travel without prior authorization WARRANTY REGISTRATION CARD The war
27. chine drain line and the floor sink or drain If a grease trap is required by code it should have a flow capacity of 5 gal lons per minute NOTE This equipment is not recommend for use with deionized water or other aggressive fluids Use of deion ized water or other aggressive fluids will result in corrosion and failure of materials and components Use of deionized water or other aggressive fluids will void the manufacturer s warranty WATER SUPPLY CONNECTION Ensure that you have read the section entitled PLUMBING THE DISHMACHINE above before proceeding Install the water supply line 1 2 pipe size minimum to the dishmachine line strainer using copper pipe It is recommended that a water shut off valve be installed in the water line between the main supply and the machine to allow access for service The water supply line is to be capable of 25 PSI flow pressure at the recommended temperature indicat ed on the data plate For the Tempstar GPX the line should also have the capacity to supply 52 2 GPH 25 PSI flow pressure For the Tempstar HH GPX the line should also have the capacity to supply 72 GPH 25 PSI flow pressure In areas where the water pressure fluctuates or is greater than the recommended pressure it is suggested that a water pres sure regulator be installed The Tempstar models covered in this manual come with water pressure regulators as standard equipment Please notify Jackson immediately if this
28. e material provided on this page is for reference only and may be subject to change without notice Jackson Enodis One Enrepara Co Sal ninae SECTION 1 SPECIFICATION INFORMATION DIMENSIONS FOR TEMPSTAR GPX DRAIN 1 1 2 NPT LEGEND B WATER INLET 1 2 NPT C ELECTRICAL CONNECTION STANDARD WALL CLEARANCE WITH DISHTABLE 4 OUTLET TO BOOSTER HEATER 3 4 NPT F INLET FROM BOOSTER HEATER 3 4 NPT ALL DIMENSIONS ARE 1 2 DUE TO ADJUSTABLE FEET O y T Ia W DOOR 17 OPEN MACHINE OPENING 60 5 8 gt i ELECTRICAL 43 CONNECTION TO THE FLOOR E B TABLE HEIGHT Lr 18 1 4 0 LJ LJ Jackson Enodis One Co Salinirnis SECTION 1 SPECIFICATION INFORMATION DIMENSIONS FOR TEMPSTAR HH GPX LEGEND DRAIN 1 1 2 NPT B WATER INLET 1 2 NPT C ELECTRICAL CONNECTION STANDARD WALL CLEARANCE WITH DISHTABLE 4 OUTLET TO BOOSTER HEATER 3 4 F INLET FROM BOOSTER HEATER 3 4 N P T ALL DIMENSIONS ARE 1 2 DUE TO ADJUSTABLE FEET MACHINE Xy S 86 1 4 W DOOR 74 3 4 OPEN ays 9 A 16 1 4 Jackson Enodis One Enrepara Co Salinirnis SECTION 1 SPECIFICATION INFORMATION TABLE DIMENSIONS 4 MINIMUM N TABLE DIMENSIONS CORNER INSTALLATION
29. e second connection on the other unit before cutting the hose Use a barbed hose fitting that is screwed onto the second connection to gauge the correct distance Ensure a smooth flow of hose without any sharp turns or kinks To aid in pushing the barbed hose fitting into the hose place the fitting on a hard surface i e the floor with the barbed end of the fitting pointing upward and push the hose down onto the fitting A small amount of lubricant i e petroleum jelly may aid in this process Barbed Hose Fitting Attach the hose fitting to this connection before making the cut at the other end of the hose Connection Cut the hose at the location where the hose is even with the yellow plastic stop Jackson Enodis One Enrepara mles Salinirnis 10 SECTION 2 INSTALLATION OPERATION INSTRUCTIONS GAS BOOSTER HEATER CONNECTIONS CONTINUED PRESSURE REGULATING VALVE BUILDINGS WATER gt HE Hal SUPPLY my Ea PHOSPHATE WATER 3 VACUUM RINSE ARM BREAKER Ob PRESSURE DISHMACHINE Y STRAINER TREATMENT CARTRIDGE A oer IO 3 4 HOSE RINSE SOLENOID VALVE AN ASTERISK k E DENOTES ITEMS INCLUDED WITH THE GAS BOOSTER 1 GAS BOOST ER HEATER PRESSURE RELIEF VALVE 3 4 HOSE THERMAL EXPANSION TANK TEMPERATURE PRESSURE GAGE AA A EE A
30. e the rack of clean ware Replace with a rack of soiled ware and close the doors The process will then repeat itself Jackson Enodis One 1 Salinirnis 12 SECTION 2 INSTALLATION OPERATION INSTRUCTIONS 2 242 a OPERATION INSTRUCTIONS CONTINUED OPERATIONAL INSPECTION Based upon usage the pan strainer may become clogged with soil and debris as the workday progresses Operators should regularly inspect the pan strainer to ensure it has not become clogged If the strainer does it will reduce the washing capability of the machine Instruct operators to clean out the pan strainer at regular intervals or as required by work load SHUTDOWN AND CLEANING At the end of the workday close the doors When the unit completes the cycle turn the power switch to the OFF position and open the doors Remove and clean the pan strainer Remove the drain stopper from the tub and allow the tub to drain NOTE the wash tank water will be hot so caution is advised Once the wash tub is drained remove the pump suction strainer Remove soil and debris from the strainer and set to the side Unscrew the wash and rinse arms from their manifolds Remove the endcaps and flush the arms with water Use a brush to clean out the inside of the arms If the noz zles appear to be clogged use a toothpick to remove the obstruction Wipe the inside of the unit out removing all soil and scraps Reassemble the wash and rinse arms a
31. er personnel of any problems and of the location of the service breaker Replace the control box cover and tighten down the screws Jackson Enodis One Enrepara 1 Salinirnis SECTION 2 INSTALLATION OPERATION INSTRUCTIONS GAS BOOSTER HEATER CONNECTIONS A WARNING A ENSURE THAT THERE IS NO ELECTRICAL POWER APPLIED TO THE MACHINE WHEN MAKING GAS CONNECTION CHECK ALL GAS CONNECTIONS FOR LEAKS PRIOR TO APPLYING POWER THE GASES USED FOR COMBUSTION IN THIS DISH MACHINE ARE HIGHLY FLAMMABLE DO NOT SMOKE AROUND THIS MACHINE ENSURE THAT THE AREA WHERE THIS MACHINE IS TO BE INSTALLED IS WELL VENTILATED TO PREVENT THE BUILD UP OF COMBUSTIBLE GASES ENSURE THAT ALL LOCAL HEALTH FIRE AND BUILDING CODES ARE BEING ADHERED TO WHEN INSTALLING THIS MACHINE VERIFY WITH LOCAL OFFICIALS IF THERE ARE ANY QUESTIONS INSTALL A SHUT OFF VALVE AT THE GAS SOURCE Due to the fact that each customer may have different requirements for the orientation of the gas booster heater relative to the main dishmachine the hose lengths that connect the two units must be customized during each installation To prevent incorrect measurements of the hose it is recommended to place one barbed hose fitting into the end of the uncut length of hose coil and attach that fitting to an appropriate connection Run the hose to the corresponding connection on the other unit before cutting the hose Use a barbed hose fitting that is screwed into th
32. is One 1 Salinirnis SECTION 4 ELECTRICAL SCHEMATICS TEMPSTAR HH GPX 208 230 VOLT 50 60 HERTZ SINGLE PHASE LEGEND LL Le Ld POWER DISTRIBUTION BLOCK GND GND 44 2 CHASSIS GROUND WASH PUMP MOTOR CIRCULATOR PUMP CONTROL RELAY WASH MOTOR CONTACTOR WASH TEMPERATURE RELAY POWER SWITCH DOOR SVITCH NORMAL DELIME SWITCH CYCLE SELECTOR SWITCH 1 CYCLE SELECTOR SWITCH 2 CYCLE SELECTOR SWITCH 3 CYCLE SELECTOR SWITCH 4 CYCLE SWITCH AUTO START RESET SWITCH WASH CYCLE SWITCH RINSE FILL SWITCH POVER LIGHT CYCLE LIGHT FILL SOLENOID HIGH LEVEL PROBE WASH THERMOSTAT SWITCH TIMER MOTOR WATER LEVEL CONTROL WASH CYCLE TIMER CONSTANT VOLTAGE CONNECTION SWITCHED VOLTAGE CONNECTION RINSE AID CONNECTION DETERGENT CONNECTION GRY YEL COMPONENT LAYOUT roa Ceic3ic4 gt 9905 002 57 60a ar DETERGENT DISPENSER CONNECTION CONSTANT VOLTAGE CONNECTION Jackson 20 Enodis One 1 Sal ninae SECTION 5 JACKSON MAINTENANCE amp REPAIR CENTERS SECTION 5 JACKSON MAINTENANCE amp REPAIR CENTERS ALABAMA TO HAWAII ALABAMA JONES McLEOD APPLIANCE SVC 1616 7TH AVE NORTH BIRMINGHAM AL 35203 205 251 0159 800 821 1150 FAX 205 322 1440 service jones mcleod com JONES McLEOD APPLIANCE SVC 854 LAKESIDE DRIVE MOBILE AL 36693 334 666 7278 800 237 9859 FA
33. nd replace them in the unit The arms only need to be hand tight do not use tools to tighten them down Reinstall the drain stopper and strainers and close the doors WATER CONSUMPTION ISSUES AND EFFICIENCY The Tempstar HH GPX provides you the customer with the ability to control the hourly rack capacity of the machine Extending the wash cycle to wash severely soiled ware such as mixing bowls does not increase the machine s water consumption However selecting a longer time cycle does lower the amount of dishes the machine will be able to wash per hour It is important for operators to select the correct wash cycle depending on the amount of washing required Not every rack of dishes requires the machine to be set on the longest wash cycle Using good prescrapping procedures and observing the results of individual racks of ware operators will soon gain the expe rience and knowledge required to ensure that the Tempstar HH GPX operates at peak efficiency for your needs Water hardness and detergent usage will also effect the results of the Tempstar HH GPX This manual provides a page enti tled Detergent Control for your reference It is recommended that owners and operators take the time to carefully review this section in order to ensure that everything is done to make sure the Tempstar HH GPX operates at peak performance Jackson Enodis One Enrepara 1 Salinirnis 13 SECTION 3
34. pical fixed trip cir cuit breaker sizes as listed in the NEC 2002 Edition Local codes may require more stringent protection than what is dis played here Always verify with your electrical service con tractor that your circuit protection is adequate and meets all applicable national and local codes These numbers are pro vided in this manual simply for reference and may change without notice at any given time RINSE TYPICAL HEATER TOTAL ELECTRICAL VOLTS PH HZ RATINGS AMPS CIRCUIT 110 120 1 60 N A 14 20 AMP 208 240 1 60 N A 7 15 AMP WATER REQUIREMENTS INLET TEMPERATURE BOOSTER OUTPUT BTU 60 110 F 100 000 110 140 F 60 000 WASH TEMPERATURE MINIMUM 150 F RINSE TEMPERATURE MINIMUM 180 F GALLONS PER HOUR 52 2 WATER LINE SIZE NPT MINIMUM 1 2 DRAIN LINE SIZE NPT MINIMUM 1 1 2 FLOW PRESSURE NPT 20 5 NOTE Always refer to the machine data plate for specific electrical and water requirements The material provided on this page is for reference only and may be subject to change without notice Jackson Enodis One Enrepara Co Sal ninae SECTION 1 SPECIFICATION INFORMATION PERFORMANCE CAPABILITIES OPERATING CAPACITY RACKS HOUR RACKS PER HOUR DISHES PER HOUR GLASSES PER HOUR OPERATING CYCLE SECONDS SELECTION A WASH TIME RINSE TIME TOTAL CYCLE TIME SELECTION B WASH TIME RINSE TIME DWELL TIME TOTAL CYCLE TIME SELECTION C WASH TIME RINSE TIME DWELL TIME
35. ranty registration card supplied with the machine must be returned to Jackson MSC within 30 days to validate the warranty REPLACEMENT PARTS WARRANTY Jackson replacement parts are warranted for a period of 90 days from the date of installation or 180 days from the date of shipment from the factory which ever occurs first PRODUCT CHANGES AND UPDATES Jackson MSC reserves the right to make changes in design and specification of any equipment as engineering or necessity requires THIS IS THE ENTIRE AND ONLY WARRANTY OF JACKSON MSC JACKSON S LIABILITY ON ANY CLAIM OF ANY KIND INCLUDING NEGLIGENCE WITH RESPECT TO THE GOODS OR SERVICES COVERED HEREUNDER SHALL IN NO CASE EXCEED THE PRICE OF THE GOODS OR SERVICES OR PART THEREOF WHICH GIVES RISE TO THE CLAIM THERE ARE NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING FOR FITNESS OR MERCHANTABILITY THAT ARE NOT SET FORTH HEREIN OR THAT EXTEND BEYOND THE DURATION HEREOF UNDER NO CIRCUMSTANCES WILL JACKSON MSC BE LIABLE FOR ANY LOSS OR DAMAGE DIRECT OR CONSEQUENTIAL OR FOR THE DAMAGES IN THE NATURE OF PENALTIES ARISING OUT OF THE USE OR INABILITY TO USE ANY OF ITS PRODUCTS ITEMS NOT COVERED This warranty does not cover cleaning or deliming of the unit or any component such as but not limited to wash arms rinse arms or strain ers at anytime Nor does it cover adjustments such as but not limited to timer cams thermostats or doors beyond 30 days from the date of installation In addition the
36. st be completely filled before operating the wash pump to prevent damage to the component Once the wash tub is filled the unit is ready for operation FILLING THE WASH TUB TEMPSTAR HH GPX For the initial fill ensure that the cycle selection switch is in the AUTO automatic position and place the power switch in the ON position The unit will fill automatically and run through a rinse cycle Open the doors and verify that the water level is correct Hereafter the water level is controlled by the overflow tube Verify that the drain stopper is preventing the wash tub water from draining excessively There may be some slight leakage from the drain hole Verify that there are no other leaks on the unit before proceeding any further The wash tub must be complete ly filled before operating the wash pump to prevent damage to the component Once the wash tub is filled the unit is ready for operation WARE PREPARATION Proper preparation of ware will help ensure good results and less re washes If not done properly ware may not come out clean and the efficiency of the dishmachine will be reduced It is important to remember that dishmachine is not a garbage disposal and that simply throwing unscraped dishes into the machine simply defeats the purpose altogether of washing the ware Scraps should be removed from ware prior to being loaded into a rack Pre rinsing and pre soaking are good ideas especially for silverware and casserole dishes
37. strainer to work in the way it was designed to Wipe out strainers with a rag and rinse under a faucet if necessary For stubborn debris a toothpick should be able to dislodge any obstructions from the perforations Always ensure that strainers are placed back in the machine before operation and that they lay flat in the tub You may wish to also refer to the page entitled Detergent Control in order to learn more about how your water hardness will effect the performance of your machine Hard water makes dishmachines work harder and decreases efficiency Again it is important to remind operators that trying to perform corrective maintenance on the dishmachine could lead to larg er problems or even cause harm to the operator If a problem is discovered secure the dishmachine using proper shut down procedures as listed in this manual and contact a QUALIFIED SERVICE AGENCY as listed in the back of this manual Some problems however may having nothing to do with the machine itself and no amount of preventative maintanence is going to help A common problem has to do with temperatures being too low Verify that the water temperatures coming to your dishmachine match the requirements listed on the machine data plate There can be a variety of reasons why your water tem perature could be too low and you should discuss it with a QUALIFIED SERVICE AGENCY to determine what can be done By following the operating and cleaning instructions in this manual
38. tl com MONTANA RESTAURANT APPLIANCE SVC 7219 ROOSEVELT WAY NE SEATTLE WA 98115 206 524 8200 800 433 9390 FAX 206 525 2890 info restappl com NEBRASKA GOODWIN TUCKER GROUP 7535 D STREET OMAHA NE 68124 402 397 2880 800 228 0372 FAX 402 397 2881 goodwintuc aol com NEVADA HI TECH COMMERCIAL SVC 400 E MEAD BLVD LAS VEGAS NV 89030 702 649 4616 877 924 4832 FAX 702 649 4607 GCS SERVICE INC LAS VEGAS NV 800 822 2303 NEW HAMPSHIRE GCS SERVICE INC 180 SECOND STREET CHELSEA MA 02150 617 889 9393 800 225 1155 FAX 617 889 1222 ACE SERVICE CO 500 HARVEY RD MANCHESTER NH 03103 603 668 5070 800 225 4510 FAX 603 626 6067 taceservice aol com MASSACHUSETTS RESTAURANT SUPPLY 34 SOUTH STREET SOMERVILLE MA 02143 617 868 1930 800 338 6737 FAX 617 868 5331 NEW JERSEY JACKSON FASPRAY SVC 155 SARGEANT AVE CLIFTON NJ 07013 973 471 8000 800 356 6740 FAX 973 471 1289 jfs155 aol com AMERICAN KITCHEN MACHINERY amp REPAIR 204 QUARRY STREET PHILADELPHIA PA 19106 215 627 7760 800 848 7760 FAX 215 627 1604 GCS SERVICE INC 817 N THIRD STREET PHILADELPHIA PA 19123 215 925 6217 800 441 9115 FAX 215 925 6208 NEW JERSEY cont ELMER SCHULTZ SERVICES 201 WASHINGTON AVE PLEASANTVILLE NJ 08232 609 641 0317 800 378 1641 FAX 609 641 8703 elmer2 erols com NEW MEXICO STOVE PARTS SUPPLY CO 2120 SOLANA S
39. warranty will only cover the replacement of wear items such as curtains drain balls door guides or gaskets during the first 30 days after installation Also not covered are conditions caused by the use of incorrect non Commercial grade detergents incorrect water temperature or pressure or hard water conditions Jackson Enodis One Enrepara mies Salinirnis REVISION REVISION MADE APPLICABLE MAW N A MAW NOMENCLATURE FOR THE MODELS COVERED IN THIS MANUAL Jackson an EnSdis company TEMPSTAR HH GPX TEMPSTAR GPX Gas heated hot water sanitizing door type dishmachine TEMPSTAR HH GPX Gas heated hot water sanitizing door type dishmachine with higher hood Model Serial No Installation Date Service Rep Name Phone No Jackson MSC Inc provides technical support for all of the dishmachines detailed in this manual We strongly recommend that you refer to this manual before making a call to our technical support staff Please have this manual with you when you call so that our staff can refer you if necessary to the prop er page Technical support is available from 8 00 a m to 5 00 p m EST Monday through Friday Technical support is not available on holidays Contact technical support toll free at 1 888 800 5672 Please remember that technical support is available for service personnel only Jackson Enodis One Enrepara 1 Salinirnis
40. you should get the most efficient results from your machine As a reminder here are some steps to take to ensure that you are using the dishmachine the way it was designed to work Ensure that the water temperatures match those listed on the machine data plate Ensure that all strainers are in place before operating the machine Ensure that all wash and or rinse arms are secure in the machine before operating Ensure that drains are closed sealed before operating Remove as much soil from dishes by hand as possible before loading into racks Do not overfill racks Ensure that glasses are placed upside down in the rack Ensure that all chemicals being injected to machine have been verified as being at the correct concentrations Clean out the machine at the end of every workday as per the instructions in the manual 10 Always contact a QUALIFIED SERVICE AGENCY whenever a serious problem arises 11 Follow all safety procedures whether listed in this manual or put forth by local state or national codes regulations OOMONDARWDND Jackson Enodis One Enrepara Salinirnis SECTION 4 ELECTRICAL SCHEMATICS SECTION 4 ELECTRICAL SCHEMATICS TEMPSTAR GPX 115 VOLT 50 60 HERTZ SINGLE PHASE N re g 8 WHT DETERGENT DISPENSER CONNECTION LEGEND CONSTANT VOLTAGE ay CONNECTION LI N POWER DISTRIBUTION BLOCK GND GROUND 1
Download Pdf Manuals
Related Search